This patch replaces 'of_flat_dt_is_compatible' with 'of_machine_is_compatible'.
The TL-WDR4900 platform file won't compile in the 6.1 kernel. The platform
files for the rest of the routers have been reworked or based on newer
solutions.
Let's make the TL-WDR4900 consistent with them.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This fixes the following compile problem:
````
CC arch/mips/kernel/vpe-mt.o
arch/mips/kernel/vpe-mt.c: In function 'vpe_run':
arch/mips/kernel/vpe-mt.c:32:23: error: unused variable 'physical_memsize' [-Werror=unused-variable]
32 | unsigned long physical_memsize = 0L;
| ^~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[6]: *** [scripts/Makefile.build:289: arch/mips/kernel/vpe-mt.o] Error 1
````
physical_memsize was removed from upstream kernel, see:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=5b4f6c5ff65c8551018ccea40c569afd759734c0
Fixes: 387fde0da0 ("kernel: bump 5.15 to 5.15.150")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commit 2d63d42f5e ("mediatek: convert to new LED color/function
format where possible") leaves Xiaomi Redmi AX6000 un-converted,
the two LEDs become dead.
Now, LEDs are alive again.
Fixes: 2d63d42f5e ("mediatek: convert to new LED color/function
format where possible")
Signed-off-by: Furong Xu <xfr@outlook.com>
ath25 has been on life support for the last couple of releases, eventually
leading to marking it as source-only in 2023.
It has been basically only touched to do a kernel bump so that we can make
the new OpenWrt release which was a challenge due to small RAM amount.
However, with the attempt of kernel 6.1 update it turns out that kernel
cannot even finish booting due to RAM constraints, so its time to let this
target go.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Netgear WAX214 is a 802.11 ax dual-band AP
with PoE. (similar to Engenius EWS357APV3)
Specifications:
• CPU: Qualcomm IPQ6010 Quad core Cortex-A53
• RAM: 512MB of DDR3
• Storage: 128MB NAND (Macronix MX30UF1G18AC)
• Ethernet: 1x 1G RJ45 port (QCA8072) PoE
• WIFI:
2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate
5GHz: Qualcomm QCN5052 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate
• LEDs:
4 x GPIO-controlled LEDs
- 1 Power LED (orange)
- 1 LAN LED (blue)
- 1 WIFI 5g LED (blue)
- 1 WIFI 2g LED (blue)
black_small_square Buttons: 1x soft reset
black_small_square Power: 12V DC jack or PoE (802.3af )
An populated serial header is onboard, format is
1.25mm 4p (DF13A-4P-1.25H)
RX/TX is working, bootwait is active, secure boot is not
enabled.
The root password of the stock firmware is unknown,
but failsafe mode can be entered to reset the password.
Installation Instructions:
- obtain serial access
- stop auto boot (press "4", Entr boot command line
interface)
- setenv active_fw 0 (to boot from the primary rootfs,
or set to 1 to boot from the secondary rootfs
partition)
- saveenv
- tftpboot the initramfs image
- bootm
- copy
openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
to the device
- write the image to the NAND:
- cat /proc/mtd and look for rootfs partition (should
be mtd11,
or mtd12 if you choose active_fw 1)
- ubiformat /dev/mtd11 -f -y
openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
- reboot
Note: the firmware is senao-based. But I was unable to build
a valid senao-header into the image.
Maybe they changed the header format and senaoFW isn't
working any more.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
BCM63xx maintainance is a PITA since there's no full Device Tree support and
therefore every board needs it's own definition in board_bcm963xx.c
There's no DSA support for this board and there have been very few
contributions in the last years.
Moreover, BCM63xx SoCs >= BCM6358 are already supported in bmips target, so
any efforts to keep this target alive aren't worth the time.
Let's focus the community efforts on improving bmips instead.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The SolidRun ClearFog Pro is a router based on the SolidRun CN9130 SOM.
Specs:
- SoC: Quad-Core Cortex-A72 CN9130 SoC
- RAM: 4GiB DDR4
- Serial: Micro-USB port on front (FT232R, 115200 8n1)
- Storage: 8GiB eMMC, microSD card slot, 8MiB SPI NOR flash
- Ethernet: 7x GbE (1 port dedicated on SoC, 6 port switch with single GbE CPU port)
- SFP: 1x SFP+
- USB: 1x USB-A 3.1 Gen 1
- PCIe: 2x mini PCIe (one slot with USB and SIM card socket)
- SATA: 1x M.2 Key-B
In addition to the usual connectivity options this device also features
an internal mikroBUS expansion connector.
SATA is currently untested due to lack of a suitable M.2 SSD.
Installation
============
1. Write sdcard sysupgrade image to microSD card using dd or similar
2. Insert microSD card into router and apply power
3. Device boots into OpenWRT
4. (optional) dd sysupgrade image to /dev/mmcblk0 to install to eMMC
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
Upstream a patch adding support for cpufreq on AP807-based SoC like the
CN913x was submitted. Include it in patches to ensure best performance
under load and lowest power consumption in idle.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
ELECOM WAB-I1750-PS is a 2.4/5 GHz band 11ac (Wi-Fi 5) access point,
based on QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN : 2.4/5 GHz 3T3R
- 2.4 GHz : Qualcomm Atheros QCA9558 (SoC)
- 5 GHz : Qualcomm Atheros QCA9880
- Ethernet : 2x 10/100/1000 Mbps
- phy ("PD") : Atheros AR8035
- phy ("PSE") : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART : 2x RJ-45 port
- "SERVICE" : TTL (3.3V)
- port : ttyS0
- assignment : 1:3.3V, 2:GND, 3:TX, 4:RX
- settings : 115200n8
- note : no compatibility with "Cisco console cable"
- "SERIAL" : RS232C (+-12V)
- port : ?
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- settings : 115200n8
- note : compatible with "Cisco console cable"
- Buzzer : 1x GPIO-controlled
- USB : 1x USB 2.0 Type-A
- Power : DC jack or PoE
- DC jack : 12 VDC, 1.04 A (device only, rating)
- PoE : 802.3af/at, 48 VDC, 0.26 A (device only, rating)
- note : supports 802.3af supply on PSE (downstream) port
when powered by DC adapter or 802.3at PoE
Flash instruction using factory.bin image:
1. Boot WAB-I1750-PS without no upstream connection (or PoE connection
without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
firmware update page
("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
("アップデート") button
4. Wait ~120 seconds to complete flashing
Revert to OEM firmware:
1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot
Notes:
- To use the "SERVICE" port, the connection of 3.3V line is also
required to enable console output.
The uart line of "SERVICE" is branched out from the internal pin
header with 74HC126D and 3.3V line is connected to OE pin on it.
- "SERIAL" port is provided by HS UART on QCA9558 SoC that has
compatibility with qca,ar9330-uart, but QCA955x SoC's is not supported
on Linux Kernel and OpenWrt.
- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
3.5 A adapter is recommended. (official: WAB-EX-ADP1)
MAC addresses:
Ethernet (PD, PSE): 00:90:FE:xx:xx:0A (Config, ethaddr (text))
2.4GHz : 00:90:FE:xx:xx:0A (Config, ethaddr (text))
5GHz : 00:90:FE:xx:xx:0B
[original work]
Signed-off-by: Yanase Yuki <dev@zpc.st>
[update for NVMEM and others]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
ELECOM WAB-S1167-PS is a 2.4/5 GHz band 11ac (Wi-Fi 5) access point,
based on QCA9557.
Specification:
- SoC : Qualcomm Atheros QCA9557
- RAM : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm Atheros QCA9557 (SoC)
- 5 GHz : Qualcomm Atheros QCA9882
- Ethernet : 2x 10/100/1000 Mbps
- phy ("PD") : Atheros AR8035
- phy ("PSE") : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART : 1x RJ-45 port
- "SERVICE" : TTL (3.3V)
- port : ttyS0
- assignment : 1:3.3V, 2:GND, 3:TX, 4:RX
- settings : 115200n8
- note : no compatibility with "Cisco console cable"
- Buzzer : 1x GPIO-controlled
- USB : 1x USB 2.0 Type-A
- Power : DC jack or PoE
- DC jack : 12 VDC, 1 A (device only, rating)
- PoE : 802.3af/at, 48 VDC, 0.25 A (device only, rating)
- note : supports 802.3af supply on PSE (downstream) port
when powered by DC adapter or 802.3at PoE
Flash instruction using factory.bin image:
1. Boot WAB-S1167-PS without no upstream connection (or PoE connection
without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
firmware update page
("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
("アップデート") button
4. Wait ~120 seconds to complete flashing
Revert to OEM firmware:
1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot
Notes:
- To use the "SERVICE" port, the connection of 3.3V line is also
required to enable console output.
The uart line of "SERVICE" is branched out from the internal pin
header with 74HC126D and 3.3V line is connected to OE pin on it.
- The same PCB is used with WAB-S600-PS.
- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
3.5 A adapter is recommended. (official: WAB-EX-ADP1)
MAC addresses:
Ethernet (PD, PSE): 00:90:FE:xx:xx:04 (Config, ethaddr (text))
2.4GHz : 00:90:FE:xx:xx:04 (Config, ethaddr (text))
5GHz : 00:90:FE:xx:xx:05
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
ELECOM WAB-S600-PS is a 2.4/5 GHz band 11n (Wi-Fi 4) access point, based
on QCA9557.
This device also supports 11ac (Wi-Fi 5) with the another official
firmware.
Specification:
- SoC : Qualcomm Atheros QCA9557
- RAM : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm Atheros QCA9557 (SoC)
- 5 GHz : Qualcomm Atheros QCA9882
- Ethernet : 2x 10/100/1000 Mbps
- phy ("PD") : Atheros AR8035
- phy ("PSE") : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART : 1x RJ-45 port
- "SERVICE" : TTL (3.3V)
- port : ttyS0
- assignment : 1:3.3V, 2:GND, 3:TX, 4:RX
- settings : 115200n8
- note : no compatibility with "Cisco console cable"
- Buzzer : 1x GPIO-controlled
- USB : 1x USB 2.0 Type-A
- Power : DC jack or PoE
- DC jack : 12 VDC, 1 A (device only, rating)
- PoE : 802.3af/at, 48 VDC, 0.25 A (device only, rating)
- note : supports 802.3af supply on PSE (downstream) port
when powered by DC adapter or 802.3at PoE
Flash instruction using factory.bin image:
1. Boot WAB-S600-PS without no upstream connection (or PoE connection
without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
firmware update page
("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
("アップデート") button
4. Wait ~120 seconds to complete flashing
Revert to OEM firmware:
1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot
Notes:
- To use the "SERVICE" port, the connection of 3.3V line is also
required to enable console output.
The uart line of "SERVICE" is branched out from the internal pin
header with 74HC126D and 3.3V line is connected to OE pin on it.
- The same PCB is used with WAB-S1167-PS.
- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
3.5 A adapter is recommended. (official: WAB-EX-ADP1)
MAC addresses:
Ethernet (PD, PSE): BC:5C:4C:xx:xx:7C (Config, ethaddr (text))
2.4GHz : BC:5C:4C:xx:xx:7C (Config, ethaddr (text))
5GHz : BC:5C:4C:xx:xx:7D
[original work of common dtsi part for WAB-I1750-PS]
Signed-off-by: Yanase Yuki <dev@zpc.st>
[adding support for WAB-S600-PS]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The original commit had an invalid setting of the
led status for this device.
There is no gpio pin connected to that led so lets
remove these from the u7621-01 dtsi file.
Signed-off-by: David Bentham <db260179@gmail.com>
Update the default network configuration for Gateworks Newport boards
such that the left-most front-panel NIC is WAN and any additional are in
LAN bridge:
- gw610x/gw6903; single NIC: eth0
- gw620x/gw630x; two NIC's from left to right are: eth1 eth0
- gw640x; multiple NIC's from left to right: eth4 eth0 eth1 eth2 eth3
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
it is possible to boot and run OpenWrt from an image on an USB-Stick
on the MyBook Live DUO. (No, the MyBook Live Single does NOT have an
USB-Port and attempts at enabling it sadly all failed... so far).
To do that:
First, prepare a USB-Stick by writing the raw and uncompressed OpenWRT
factory image for the device onto the stick (i.e.
# gunzip -c openwrt-*wd_mybooklive*-factory.img.gz > /dev/sd$XX).
Then enter the u-boot via an attached TTL/CMOS 3.3V cable adapter and
give the following commands a try in the:
usb start; sata init
ext2load usb 0:1 ${fdt_addr_r} /boot/apollo3g.dtb
ext2load usb 0:1 ${kernel_addr_r} /boot/uImage
setenv bootargs 'root=/dev/sdc2 rw rootfstype=squashfs,ext4 rootdelay=5'
run addtty; bootm ${kernel_addr_r} - ${fdt_addr_r}
Notes:
- booting from USB-Sticks takes a long time! Be prepared to wait a few
minutes. (~3 minutes for 4 MiB /boot/uImage file on a USB 2.0 Stick)
- the bootargs part 'root=/dev/sdX2' depends on how many HDDs/SSDs are
slotted in. (if none: then use sda, if one: sdb. if two: sdc)
- rootdelay is important as the storage on the USB-Sticks do not show
up fast enough. 5 seconds might be excessive though.
- it's possible to concat these commands together in one line and
write it into u-boot's "bootcmd" environment variable and save the
environment to make the device to always boot from USB from then on.
if you have accidentally overridden the 'bootcmd' and want to return
to 'spec' enter the following commands :
setenv bootcmd 'run boot_sata_script_ap2nc'
saveenv
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Note about the MyBook Live.
The MyBook Live didn't have the encompassing fixed-partitions.
This is needed for the u-boot,env compatible to be read as otherwise
the kernel assumes this is a legacy NOR/NAND node and this binding
is unsupported.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Enable DEBUG_BUGVERBOSE by default on qualcommax as without it once BUG()
is called we will not get any output other than
"------------[ cut here ]------------"
which is not usefull at all, so since we dont have kernel size constraints
lets enable it by default.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use type casts to prevent compiler warnings which are going to turn
into errors when we switch to Linux 6.6.
In the long run we should try to get rid of this downstream driver
now that RTL8367S is support by the rtl8365mb DSA driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rename kernel patches accepted upstream to indicate at which version
they have been accepted, replacing downstream variants which what was
accepted upstream. Note that some of them are fixes which will
find their way to older kernel versions as well via linux-stable.
No functional changes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some backported thermal patches ended up with the wrong kernel
version in their filename. Fix this.
Fixes: c36de2e73a ("mediatek: backport a hell of thermal commits")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Kirkwood SoCs all have an onchip RTC that can hold the time
over e.g. a reboot which will help if no NTP servers are available.
Create a kernel module package for the Marvell RTC, and add it to
all Kirkwood devices that do not have their own discrete
battery-backed RTC. Adding it to platforms with a proper RTC
is just surplus.
All Kirkwoods have at least one RTC so add RTC to the features
list for Kirkwood as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MT7981B /256MB /16MB SPI (XM25QH128C)
AX 2.4Ghz
AX 5Ghz 160Mhz wide
1Gbit LAN
OEM:
root@RE3000:~# ifconfig |grep HWaddr
br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0 (label)
br-wan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
ra0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
ra2 Link encap:Ethernet HWaddr 82:XX:XX:28:XX:X0
rax0 Link encap:Ethernet HWaddr 82:XX:XX:38:XX:X0
rax2 Link encap:Ethernet HWaddr 82:XX:XX:58:XX:X0
OpenWrt
root@OpenWrt:/# ifconfig |grep HW
br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
phy0-ap0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
phy1-ap0 Link encap:Ethernet HWaddr 82:XX:XX:08:XX:X1
tftp Installation via u-boot:
Connect TTL3.3V converter
connector is under the radiator Set speed 115200 8 N 1
Interrupt boot process by holding down-arrow key during boot then
>> 6. Load image
>> 0 - TFTP client (Default)
enter IP adresses and initramfs-kernel.bin
write to flash via sysupgrade or gui
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
This target adds support for the Allwinner D1 RISC-V based SoCs.
- RISC-V single-core T-Head C906 (RV64GCV)
- Tensilica HiFi4 DSP
- DDR2/DDR3 support
- 10/100/1000M ethernet
- usual peripherals like USB2, SPI, I2C, PWM, etc.
Four boards are supported:
- Dongshan Nezha STU
- 512Mb RAM
- ethernet
- LicheePi RV Dock
- 512Mb RAM
- wireless-only (RTL8723DS)
- MangoPi MQ-Pro
- 512Mb RAM
- there are pads available for an SPI flash
- wireless-only (RTL8723DS)
- Nezha D1
- 512Mb/1Gb/2Gb RAM
- 256Mb NAND flash
- ethernet, wireless
Installation:
Standard SD-card installation via dd-ing the generated image to
an SD-card of at least 256Mb.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The boot loader does not have a fixed size limit for the kernel,
so we're free to change the layout. This may break sysupgrade, but a fresh
flash from initramfs works.
Fixes: 6e2962d4c5 ("mediatek: mt7622: skip build for MT7622 rfb1 (UBI)")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The Arcadyan VRV9510KWAC23 (trade name Livebox Next) is a Lantiq router distributed by some spanish ISPs
Hardware:
- SoC: Lantiq VRX200
- CPU: 2x MIPS 34Kc 500 MHz
- RAM: 256 MiB DDR2
- Flash: 128 MiB NAND
- Ethernet: Built-in Gigabit Ethernet switch, 5x 1GbE
- Wifi 2.4GHz: Broadcom BCM43222KFBG 802.11b/g/b MIMO 2T2R
- Wifi 5GHz: Broadcom BCM4360KMLG 802.11ac MIMO 3T3R
- USB: 2x USB 2.0
- DSL: Built-in VDSL/ADSL2+ XWAY VRX208
- LEDs: 8x
- Buttons: 4x
- Phone: Lantiq PEF 42068 V XWAY SLIC120
Install instructions:
Detailed instructions can be found on the wiki https://openwrt.org/toh/arcadyan/vrv9510kwac23
1. Boot into UART mode and upload the the https://raw.githubusercontent.com/danielhuici/arcadyan-vrv9510kwac23-utils/main/u-boot.asc file via serial console to boot into U-Boot.
2. Perform a backup of the NAND
3. Setup a TFTP server and serve the https://github.com/danielhuici/arcadyan-vrv9510kwac23-utils/raw/main/u-boot.ltq.lzo.nandspl. Replace the OEM bootloader with this one. Erase your NAND and write the image into it
4. Reboot the router
5. Serve the OpenWrt ramdisk image on your TFTP server and boot it via U-Boot
6. When OpenWrt boots, flash the SquashFS OpenWrt image using LuCi interface, so OpenWrt gets installed into the NAND
Signed-off-by: Daniel Huici <danielhuici@hotmail.com>
Drop the flow-hash of the skb when forwarding to the L2TP netdev.
This avoids the L2TP qdisc from using the flow-hash from the outer
packet, which is identical for every flow within the tunnel.
This does not affect every platform but is specific for the ethernet
driver. It depends on the platform including L4 information in the
flow-hash.
Signed-off-by: David Bauer <mail@david-bauer.net>
The following kernel module package was added to the build recipe for the
Turris Omnia: kmod-mt7915-firmware
This module enables support for the official Wi-Fi 6 upgrade kit sold by
CZ.NIC, which includes the AW7915-NP1 miniPCIE board based on Mediatek
MT7915AN, providing 5 GHz Wi-Fi 6 connectivity. With this commit we now
support the latest Turris Omnia Wi-Fi 6 Edition
Signed-off-by: Jan Jasper de Kroon <jajadekroon@gmail.com>
Because some still unresolved bugs in this driver, which sprout
occasional questions what this patch works around, point to the issue
which started this. Being here, fill headers required by git am.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Reduce and split pcie controller memory ranges for en7523 SoC
in order to properly load a pcie card on the second port.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
