Refreshed all patches.
Removed patches because included in upstream:
- 499-mtd-parser-cmdline-Fix-parsing-of-part-names-with-co.patch
- 0071-2-PCI-qcom-Fixed-IPQ806x-PCIE-reset-changes.patch
Compile-tested on: ipq40xx, lantiq/xrx200, x86/64, ipq806x
Runtime-tested on: ipq40xx, lantiq/xrx200, x86/64
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Refreshed all patches.
Removed patches because included in upstream:
- 315-v5.10-usbnet-ipeth-fix-connectivity-with-ios-14.patch
Compile-tested on: ipq40xx, ath79, x86/64
Runtime-tested on: ipq40xx, ath79
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commit c9c7b4b394 ("kernel: add netfilter-actual-sk patch") has
touched net/ipv6/netfilter/ip6table_mangle.c which in turn has affected
910-unaligned_access_hacks.patch so the patch needs to be refreshed.
Fixes: c9c7b4b394 ("kernel: add netfilter-actual-sk patch")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The device uses a rf-kill switch instead of a button. Furthermore the
GPIO is active high.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
(cherry picked from commit 0af656e978)
As the ath79 port of this device uses a combined kernel + root
partition the uboot bootcmd variable needs to be changed. As using
cli/luci is more convenient than opening up the case and using a uart
connection, lets unlock the uboot-env partition for write access.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
(cherry picked from commit 982c1f6e42)
Commit 1bfbf2de6d ("ar71xx: serial: core: add support for boot console
with arbitrary baud rates") added support for arbitrary baud rates which
enabled 250000 baud rate for Yun. But the patch was not ported to kernel
4.9, and since then the kernel set its baud rate to 9600. This commit ports
the patch to kernel 4.14, thereby restoring the serial console of Yun.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit c90db26e05)
Commit 05d73a2a73 enabled GPIO on ethernet LED, but proper LED setup was
not added then. This commit fixes it by reverting the change on the LED.
Fixes: 05d73a2a73 ("ar71xx: Arduino Yun board 'WLAN RST' button support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit a5e404d192)
Commit bb46b635df changed its partition scheme, but sysupgrade image
validation still uses the old format. This commit fixes it so that
force flag is not needed for sysupgrade.
Fixes: bb46b635df ("ar71xx: move Arduino Yun to generic building code")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 58dc1d0637)
This reverts commit 077253dd66.
The output enable pins should be disabled by default, and only enabled when
used. Otherwise unwanted conflicts might occur between MCU and SoC pins.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 43896dc0b0)
This fixes the following compile error:
drivers/mtd/nand/rb91x_nand.c: In function 'rb91x_nand_remove':
drivers/mtd/nand/rb91x_nand.c:445:16: error: 'rbni' undeclared (first use in this function)
nand_release(&rbni->chip);
Fixes: 9cad70044f ("kernel: fix nand_release() usage.")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 66e04abbb6)
There is one closing bracket too much.
Fixes: 9cad70044f ("kernel: fix nand_release() usage.")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 014d3f593a)
During porting support for this router to ath79 target
it was discovered that GPIO mapping was incorrect (GPIO11 active high).
Correct mapping for both V1 and V2 is GPIO12 active low.
Default configuration from GPL source for V2 explicitly states this, and
this was confirmed experimentally on ath79 by looking on
/sys/kernel/debug/gpio. Correctness of this was also validated for V1 by
cross-flashing vendor firmware for V1 on V2 hardware, in which reset
button also worked.
Fix it.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit f841e70640)
The TP-Link TL-MR3020 has a three-state mode slider which was previously
integrated as a button (EV_KEY). This led to spurious activations of
failsafe mode.
Set the type for the button to switch (EV_SW), to avoid unintended
activations of failsafe mode.
Related: commit 27f3f493de ("gpio-button-hotplug: unify polled and
interrupt code")
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b017a016cc)
The -O option for the tplink-v1-header was missing for the TP-Link
TL-WR902AC v1, while safeloader and MTDPARTS where set up with a
single firmware partition.
This led to bootloops after using sysupgrade.
Fixes: FS#3118
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a7b07f8ba8)
So far, specifying "BOARD_NAME := routerboard" is required by the
upgrade code of Mikrotik NAND devices, as "sysupgrade-routerboard"
is hardcoded in platform_do_upgrade_mikrotik_rb().
This patch replaces the latter with a grep for the name like it
is already done in nand_upgrade_tar() in /lib/upgrade/nand.sh.
This should enable upgrades from ar71xx to ath79 without setting
BOARD_NAME for the latter.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(backported from commit 281785d74f)
The id parameter in __rb_get_wlan_data() was incorrectly used on the
assumption that id "0" would always be tied to ath9k with RLE encoding
and positive id (in fact, only id "1" was valid) would always be tied to
("external") ath10k with LZO encoding.
Newer hardware revisions of supported devices prove this assumption to
be invalid, with ath9k caldata being now wrapped in MAGIC_ERD and LZO
compressed, so disable this check to allow newer hardware to correctly
decode caldata for ath9k. Since ath10k caldata is no longer pulled from
this implementation, this commit also disables the publication in sysfs
to avoid wasting memory.
Note: this patch assumes that ath9k caldata is never stored with the new
"LZOR" encoding scheme found on some ath10k devices.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Fetch ath10k calibration data from backported mikrotik sysfs driver
which supports the newer "LZOR" encoding.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Refreshed all patches and removed upstreamed:
oxnas/001-irqchip-versatile-fpga-Handle-chained-IRQs-properly.patch
oxnas/002-irqchip-versatile-fpga-Apply-clear-mask-earlier.patch
Fixes: CVE-2020-12114 and CVE-2020-11669
Runtime-tested on: qemu-x86-64
Compile-tested on: ath79/generic, x86/64, imx6
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Without this patch, when using rev 3 of the Atheros AR9344 SoC, the
gigabit switch (AR8327) does not work or works very erratically.
This is a re-spin of http://patchwork.ozlabs.org/patch/419857/ with a
different PLL value, according to the feedback from several users
(including myself) as shown here:
https://openwrt.org/toh/mikrotik/rb2011uias#tracking_reported_experience_with_suggested_patch_for_the_5_gige_ports
Performance is acceptable: testing L3 forwarding without NAT yields a
performance of 370 Mbit/s (iperf3 TCP) and 41 Kpps (iperf3 UDP with 64
bytes payload). Both tests show that 100% of CPU time is spent on softirq.
A similar fix for a different device (RB2011) was added in e457d22261
("Make GBit switch work on RB2011").
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
(cherry picked from commit 247043c968)
Use power led for device status.
The status led behavior has already been fixed in af28d8a539
("ath79: add support for GL.iNet GL-AR750S") when porting the
device to ath79. This fixes it for ar71xx as well.
Signed-off-by: Jan Alexander <jan@nalx.net>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit d394c354ee)
The labels on the LAN ports of the TP-Link Archer C60 v1/v2 are
actually inverted compared to the ports of the internal switch.
Add this information to 02_network.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 14a07fa1f0)
The adjustment of the MAC address for Archer C60 v2 in 10_fix_wifi_mac
is broken since a "mac" partition is not set up for this device on
ar71xx. Instead, the MAC address is already patched correctly in
11-ath10k-caldata.
Remove the useless adjustment.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit cbdc919024)
The MAC addresses for lan/wan are swapped compared to the vendor
firmware. This adjusts to vendor configuration, which is:
lan *:7b label
wan *:7c label+1
2.4g *:7b label
5g *:7a label-1
Only one address is stored in <&mac 0x8>, corresponding to the label.
This has been checked on revisions v1, v2 and v3.
Since ar71xx calculates the ath10k MAC address based on the ethernet
addresses, the number there is adjusted, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 14eb54938b)
When changing the LED names for the Archer C7 to represent the correct
color, a migration for existing UCI entries was not created.
Add a migration to keep existing LED configurations working.
Fixes commit c79c001b59 ("ar71xx: Archer C7 v1 LED names and RFKILL
fixes")
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4349d4c682)
The AVM FRITZ!WLAN Repeater 450E's WPS button is not active low.
Correct the active low flag to avoid unintenional activation of
failsafe mode on boot.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 1d4f2ca610)
Change u-boot-env partitions to be mounted as read-write for gl-ar150,
gl-domino and gl-mifi so uboot-envtools support is possible.
Signed-off-by: Kimmo Vuorinen <kimmo.vuorinen@gmail.com>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 2c1cfacdde)
When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti Rocket M Titanium, it missed connection to actual interface.
Therefore create the mapping to interface, so RSSI LEDs work without
additional configuration, after starting rssileds service.
While at that, split RSSI into ~equal intervals for 6 LEDs,
and remove coefficients needed for PWM LEDs, as this board does not
support PWM LEDs.
Finally, for complete support, enable 'rssileds' package in per-device
rootfs, so the indicator works out of box.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 83708f233d)
This image is only needed on one device (wAP AC); since this target is
going to be removed anyway it doesn't make sense to add an extra "low
RAM" image.
Fixes OOM issues on RouterBoard wAP AC.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
(cherry picked from commit 788c8485eb)
The current ethernet MAC address setup of TL-WDR4300 board is different
from the setup of stock firmware:
OpenWrt: lan = label_mac -2, wan = label_mac -2
stock: lan = label_mac, wan = label_mac +1
This patch applies to all devices using TL-WDR4300 board:
TL-WDR3600 v1
TL-WDR4300 v1
TL-WDR4300 v1 (IL)
TL-WDR4310 v1
Mercury MW4530R v1
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 9b02d32e34)
