Many NAND devices use a build recipe with "append-ubi | check-size" to
ensure factory images don't exceed the target flash partition size.
However, UBI reserves space for bad block handling and other operational
overhead, and thus 'check-size' can overestimate the space available by
several MB. In practice, this means a failed check is definitely a failure,
while a passing check is only probably a pass.
Improve the situation by teaching 'Build/append-ubi' to check image sizes
while accounting for UBI reserved blocks. Add new device variable NAND_SIZE
and use with existing IMAGE_SIZE to derate the available space. Each UBI
device reserves 20 PEBs per 1024 PEBs of the entire NAND device for bad
blocks, plus an additional 4 PEBs overhead.
Many devices can transparently enable this check by setting NAND_SIZE based
on their flash storage, and may then remove any unneeded 'check-size'.
Link: http://www.linux-mtd.infradead.org/doc/ubi.html#L_overhead
Suggested-by: Shiji Yang <yangshiji66@qq.com>
Suggested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Current factory image sizes for Linksys devices are 256-byte aligned. This
is not an issue writing factory images from the OpenWrt or Linksys GUIs,
but can lead to failures using a TFTP client from the Linksys bootloader:
NAND write: device 1 offset 0x2800000, size 0xc00100
Attempt to write to non page aligned data
NAND write to offset 2800000 failed -22
0 bytes written: ERROR
Simplify Linksys footer creation by migrating to a makefile build recipe,
and pre-pad the footer (with 0xFF) to ensure the final image is $(PAGESIZE)
aligned. Finally, remove the old linksys-image.sh script no longer needed.
Linksys footer details are given below for future reference. The 256-byte
footer is appended to factory images and tested by both the Linksys
Upgrader (observed in EA6350v3) and OpenWrt sysupgrade.
Footer format:
.LINKSYS. Checked by Linksys upgrader before continuing. (9 bytes)
<VERSION> Upgrade version number, unchecked so arbitrary. (8 bytes)
<TYPE> Model of device, space padded (0x20). (15 bytes)
<CRC> CRC checksum of factory image to flash. (8 bytes)
<padding> Padding ('0' + 0x20 * 7) (8 bytes)
<signature> Signature of signer, unchecked so arbitrary. (16 bytes)
<padding> Padding with nulls (0x00) (192 bytes)
Link: https://github.com/openwrt/openwrt/pull/11405#issuecomment-1358510123
Link: https://github.com/openwrt/openwrt/pull/11405#issuecomment-1587517739
Reported-by: Stijn Segers <foss@volatilesystems.org>
Reported-by: Wyatt Martin <wawowl@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add the make function 'exp_units' for helping evaluate k/m/g size units in
expressions, and use this to consistently replace many ad hoc substitutions
like '$(subst k,* 1024,$(subst m, * 1024k,$(IMAGE_SIZE)))' in makefiles.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Some patched u-boots may have problems with parallel build.
Do not enforce parallel build here so one can set PKG_BUILD_PARALLEL:=0
in the specific u-boot Makefile also before including the u-boot.mk.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This reverts commit 7ceb76ca3a.
Python 3.12 removes the distutils package and is therefore not
compatible. We have to check downstream what relies on distutils before
adding actual support for Python 3.12. Sorry for the noise.
With this in-place, the macOS CI job fails and turns things red, revert
for now.
Signed-off-by: Paul Spooren <mail@aparcar.org>
creates SGE encrypted factory images
to use via the D-Link web interface
rename the old factory unencrypted images to recovery
for use in the recovery console when recovery is needed
DIR-1935-A1 , DIR-853-A1 , DIR-853-A3 , DIR-867-A1 ,
DIR-878-A1 and DIR-882-A1
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
Changes introduced in commit d604a07225 ("build: add CycloneDX SBOM
JSON support") broke ImageBuilder:
Cannot open '/openwrt-imagebuilder-ath79-generic.Linux-x86_64/tmp/.packageinfo': No such file or directory
So lets fix it by wrapping the BOM generation behind condition of IB
feature check.
Fixes: #13881
Fixes: d604a07225 ("build: add CycloneDX SBOM JSON support")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
`true` might be a shell built-in, or simply not accessible in the hardcoded locations.
Replace it with a custom script that does nothing.
Signed-off-by: Ilya Katsnelson <me@0upti.me>
CycloneDX is an open source standard developed by the OWASP foundation.
It supports a wide range of development ecosystems, a comprehensive set
of use cases, and focuses on automation, ease of adoption, and
progressive enhancement of SBOMs (Software Bill Of Materials) throughout
build pipelines.
So lets add support for CycloneDX SBOM for packages and images
manifests.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
There is no standard for ABI versioning, so its not possible to find out
from `libext2fs2`, `libiwinfo20230701` or `libss2` package names if
thats just package name or package name with ABI version included. To
help with the decision, lets make ABI version aviable in package index.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Common Platform Enumeration (CPE) is a structured naming scheme for
information technology systems, software, and packages.
In order for the information to be processed further, it should also be
available in package index files.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Kernel module packages compiling is not cached (e.g. mac80211)
even with CONFIG_CCACHE on.
CC should be set to KERNEL_CC in KERNEL_MAKE_FLAGS at kernel.mk
to allow kernel module packages using ccache.
Signed-off-by: Zeyu Dong <dzy201415@gmail.com>
Make use of new toolchain define. TOOLCHAIN_DIR should be used only for
toolchain related packages and for everything else TOOLCHAIN_ROOT_DIR
and other define should be used instead.
Switch to new entry where possible.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The current code fails if we have package or host tools with no patches
to apply. The error printend is the following: (taking ubus as an
example)
make[2]: Entering directory '/home/ansuel/openwrt-ansuel/openwrt/scripts/config'
make[2]: 'conf' is up to date.
make[2]: Leaving directory '/home/ansuel/openwrt-ansuel/openwrt/scripts/config'
make[1]: Entering directory '/home/ansuel/openwrt-ansuel/openwrt'
make[2]: Entering directory '/home/ansuel/openwrt-ansuel/openwrt/package/system/ubus'
The source directory contains no quilt patches.
make[2]: *** [Makefile:81: quilt-check] Error 1
make[2]: Leaving directory '/home/ansuel/openwrt-ansuel/openwrt/package/system/ubus'
time: package/system/ubus/refresh#0.06#0.00#0.07
ERROR: package/system/ubus failed to build.
make[1]: *** [package/Makefile:120: package/system/ubus/refresh] Error 1
make[1]: Leaving directory '/home/ansuel/openwrt-ansuel/openwrt'
make: *** [/home/ansuel/openwrt-ansuel/openwrt/include/toplevel.mk:232: package/ubus/refresh] Error 2
We exit 1 after saying that there are no patches because later in the
function quilt pop fails to execute.
Having no patches for a package and calling refresh should not be
a critical error and the function should just do nothing.
To handle this improve quilt.mk with the following addition.
- If we don't have any patch for the package, we print a warning and we
create an empty series. This is useful to trick quilt and make it do
nothing.
We also create a status file .quilt_no_patch to detect in the other
function that we don't have patches to handle.
- In refresh makefile target, we check if .quilt_no_patch exist and
we skip quilt cleanup if this exist.
- In RefreshDir function we change the logic and now we delete the
patches directory and not only the content. This is done as a cleanup
to clean case with empty patches directory.
- In RefreshDir we check if .quilt_no_patch exist and we skip creating
the patches directory and copying the refreshed patches.
- In RefreshDir we delete at the end any trace of .quilt_no_patch if
present.
This is needed to support run like package/refresh that will run the
refresh process on any package present in the buildroot.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
To better reference them for diagnostic use, reference the PATCH_DIR and
FILES_DIR with the absolute path instead of using ./ and reference by
the relative location.
No behaviour change intended.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
When cmake is invoked to build a package it usually reports a warning
about unused variables passed to it. This is caused by openwrt passing
all supported variables to cmake, even if they are not all required by
the package being compiled.
To reduce clutter when compiling such packages these warnings are now
suppressed.
Approved-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tjalling Hattink <t.hattink@fugro.com>
Currently, the same information is stored at the Packages.manifest in
the 'Package:' variable and also additionally in the 'SourceName:' variable.
So we have for Packages.manifest for strongswan-charon-cmd:
```
Package: strongswan-charon-cmd
Version: 5.9.11-1
SourceName: strongswan-charon-cmd
License: GPL-2.0-or-later
Section: net
```
This is not correct. Several installable packages are built from the same
strongswan source. Therefore it makes more sense that the source name is
really the source name. In this case the it is 'strongswan'.
After this change the Packages.manifest for strongswan-charon-cmd:
```
Package: strongswan-charon-cmd
Version: 5.9.11-1
SourceName: strongswan
License: GPL-2.0-or-later
Section: net
```
In summary. The 'Package' name is the name of the package to be installed
on the target system. The 'SourceName' is the compile unit from which the
package was build from. This must be the same for all installable
packages built from the same compile unit. This commit fixes that.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
