Commit Graph

20633 Commits

Author SHA1 Message Date
Bart Lauret
4386054549 ath79: add support for TP-Link Archer C5 v1
TP-Link Archer C5 v1 is a dual band router
based on Qualcomm/Atheros QCA9558 + QCA9880.

Specification:

 - 720 MHz CPU
 - 128 MB of RAM (Various chips)
 - 16 MB of FLASH (Various chips)
 - SoC QCA9558 integrated 3T3R 2.4 GHz Wi-Fi
 - minipcie slot with 3T3R 5 GHz QCA9880-BR4A
 - 5x 10/100/1000 Mbps Ethernet (AR8327N Switch)
 - 10x LEDs, 2x software buttons

For further informwation on the device, visit the wiki:
<https://openwrt.org/toh/tp-link/archer-c5-c7-wdr7500>

Signed-off-by: Bart Lauret <bblauret@gmail.com>
2019-02-28 11:32:55 +01:00
David Santamaría Rogado
34b10b468e ath79: TP-Link Archer C7 v4 swap usb port leds
USB 1 triggers usb2 led and USB 2 triggers usb1.
Lower LED is usb1 and upper LED usb2.

Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
2019-02-28 11:32:55 +01:00
Luo chongjun
693c8fb0e3 ath79: Modify glinet x750 and AR300m MAC address offsets
In the production of glinet, the MAC address of ethernet port is
only written at the position where the ART area offset address
is 0, and the MAC address of eth1 is added 1 on the basis of eth0.

Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
2019-02-28 11:32:55 +01:00
David Bauer
95b0c07a61 ipq40xx: add support for FritzBox 7530
Hardware
--------
CPU:   Qualcomm IPQ4019
RAM:   256M
FLASH: 128M NAND
ETH:   QCA8075
VDSL:  Intel/Lantiq VRX518 PCIe attached
       currently not supported
DECT:  Dialog SC14448
       currently not supported
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
LED:    - Power/DSL green
        - WLAN green
        - FON/DECT green
        - Connect/WPS green
        - Info green
        - Info red
BTN:    - WLAN
        - FON
        - WPS/Connect
UART:  115200n8 3.3V (located under the Dialog chip)
       VCC - RX - TX - GND (Square is VCC)

Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz7530'
   subdirectory. Place it in the same directory as the 'eva_ramboot.py'
   script. It is located in the 'scripts/flashing' subdirectory of the
   OpenWRT tree.

2. Assign yourself the IP address 192.168.178.10/24. Connect your
   Computer to one of the boxes LAN ports.

3. Connect Power to the Box. As soon as the LAN port of your computer
   shows link, load the U-Boot to the box using following command.

   > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin

4. The U-Boot will now start. Now assign yourself the IP address
   192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
   server root directory and rename it to 'FRITZ7530.bin'.

5. The Box will now boot OpenWRT from RAM. This can take up to two
   minutes.

6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
   scp. SSH into the Box and first write the Bootloader to both previous
   kernel partitions.

   > mtd write /path/to/uboot-fritz7530.bin uboot0
   > mtd write /path/to/uboot-fritz7530.bin uboot1

7. Remove the AVM filesystem partitions to make room for our kernel +
   rootfs + overlayfs.

   > ubirmvol /dev/ubi0 --name=avm_filesys_0
   > ubirmvol /dev/ubi0 --name=avm_filesys_1

8. Flash OpenWRT peristently using sysupgrade.

   > sysupgrade -n /path/to/openwrt-sysupgrade.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
[removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:32:55 +01:00
Christian Lamparter
18e942b6c4 ipq40xx: fix pcie msi IRQ trigger level
From: Niklas Cassel <niklas.cassel@linaro.org>
|The databook clearly states that the MSI IRQ (msi_ctrl_int) is a level
|triggered interrupt.
|
|The msi_ctrl_int will be high for as long as any MSI status bit is set,
|thus the IRQ type should be set to IRQ_TYPE_LEVEL_HIGH, causing the
|IRQ handler to keep getting called, as long as any MSI status bit is set.
|[...]
|Not having the correct IRQ type defined will cause us to lose interrupts,
|which in turn causes timeouts in the PCIe endpoint drivers.
|
|Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
|Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:26:11 +01:00
Christian Lamparter
46b949a067 ipq40xx: enlarge PCIe BAR size
David Bauer reported that the VDSL modem (attached via PCIe)
on his AVM Fritz!Box 7530 was complaining about not having
enough space in the BAR. A closer inspection of the old
qcom-ipq40xx.dtsi pulled from the GL-iNet repository listed:

| qcom,pcie@80000 {
|       compatible = "qcom,msm_pcie";
|       reg = <0x80000 0x2000>,
|             <0x99000 0x800>,
|             <0x40000000 0xf1d>,
|             <0x40000f20 0xa8>,
|             <0x40100000 0x1000>,
|             <0x40200000 0x100000>,
|             <0x40300000 0xd00000>;
|       reg-names = "parf", "phy", "dm_core", "elbi",
|                       "conf", "io", "bars";

Matching the reg-names with the listed reg leads to
<0xd00000> as the size for the "bars".

BugLink: https://www.mail-archive.com/openwrt-devel@lists.openwrt.org/msg45212.html
Reported-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:26:11 +01:00
Christian Lamparter
ddece08bf4 kernel: owl-loader: fix sparse endian warnings
owl-loader.c:83:21: sparse: warning: incorrect type in assignment (different base types)
owl-loader.c:83:21: sparse:    expected unsigned short [usertype] reg
owl-loader.c:83:21: sparse:    got restricted __be16 const [usertype] reg
owl-loader.c:84:21: sparse: warning: incorrect type in assignment (different base types)
owl-loader.c:84:21: sparse:    expected unsigned int [usertype] val
owl-loader.c:84:21: sparse:    got restricted __be16 const [usertype] low_val
owl-loader.c:85:28: sparse: warning: restricted __be16 degrades to integer

Reported-by: kbuild test robot
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:26:11 +01:00
Christian Lamparter
ca769e081f kernel: disable touchscreen symbols
This patch removes the obsolete touchscreen config symbols
and all disables all remaining ones in the generic config.

Generated by running drivers/input/touchscreen/Kconfig

 sed -n 's/^config[[:space:]]\(.*\)/# CONFIG_\1 is not set/p' Kconfig |\
 sort -d
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:26:11 +01:00
Christian Lamparter
8bdc241d01 x86: fix geode image builds
This patch adds the disabled DRM_RADEON and DRM_AMDGPU
config symbols from the x86' config to the generic target
configs. The existing symbols in the x86' configs are kept
for now, until we know whenever we want to remove such
symbols or not (see Github PR #1831, #1825, #1828).

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:26:11 +01:00
张鹏
bbab33724d ipq40xx: add support for Qxwlan E2600AC C1 and C2
Qxwlan E2600AC C1 based on IPQ4019

Specifications:
SOC:	Qualcomm IPQ4019
DRAM:	256 MiB
FLASH:	32 MiB Winbond W25Q256
ETH:	Qualcomm QCA8075
WLAN:	5G + 5G/2.4G
	* 2T2R 2.4/5 GHz
	 - QCA4019 hw1.0 (SoC)
	* 2T2R 5 GHz
	 - QCA4019 hw1.0 (SoC)
INPUT:  Reset buutton
LED:	1x Power ,6 driven by gpio
SERIAL: UART (J5)
UUSB:	USB3.0
POWER:	1x DC jack for main power input (9-24 V)
SLOT:	Pcie (J25), sim card (J11), SD card (J51)

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Qxwlan E2600AC C2 based on IPQ4019

Specifications:
SOC:	Qualcomm IPQ4019
DRAM:	256 MiB
NOR:	16 MiB Winbond W25Q128
NAND:	128MiB Micron MT29F1G08ABAEAWP
ETH:	Qualcomm QCA8075
WLAN:	5G + 5G/2.4G
	* 2T2R 2.4/5 GHz
	 - QCA4019 hw1.0 (SoC)
	* 2T2R 5 GHz
	 - QCA4019 hw1.0 (SoC)
INPUT:  Reset buutton
LED:	1x Power, 6 driven by gpio
SERIAL: UART (J5)
USB:	USB3.0
POWER:	1x DC jack for main power input (9-24 V)
SLOT:	Pcie (J25), sim card (J11), SD card (J51)

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "ubi" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
[ added rng node. whitespace fixes, ported 02_network,
ipq-wifi Makefile, misc dts fixes, trivial message changes ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:26:11 +01:00
Roger Pueyo Centelles
59c2f8af8c ath79: add support for COMFAST CF-E120A v3
This patch adds support for the COMFAST CF-E120A v3, an outdoor wireless
CPE with two Ethernet ports and a 802.11an radio.

Specifications:

 - AR9344 SoC
 - 535/400/267 MHz (CPU/DDR/AHB)
 - 2x 10/100 Mbps Ethernet, both with PoE-in support
 - 64 MB of RAM (DDR2)
 - 8 MB of FLASH
 - 2T2R 5 GHz, up to 25 dBm
 - 11 dBi built-in antenna
 - POWER/LAN/WAN/WLAN green LEDs
 - 4x RSSI LEDs (2x red, 2x green)
 - UART (115200 8N1) and GPIO (J9) headers on PCB

Flashing instructions:

 The original firmware is based on OpenWrt so a sysupgrade image can be
 installed via the stock web GUI. Settings from the original firmware
 will be saved and restored on the new one, so a factory reset will be
 needed. To do so, once the new firmware is flashed, enter into failsafe
 mode by pressing the reset button several times during the boot
 process, while while the WAN LED flashes, until it starts flashing
 faster. Once in failsafe mode, perform a factory reset as usual.

 The U-boot bootloader contains a recovery HTTP server to upload the
 firmware. Push the reset button while powering the device on and
 keep it pressed for >10 seconds. The recovery page will be at
 http://192.168.1.1

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-02-28 11:26:10 +01:00
Marcel Jost
e6f047fa36 ramips: add TP-Link TL-WR802N-v4 support
This patch adds support for the TP-Link TL-WR802N-v4.
https://openwrt.org/toh/tp-link/tl-wr802n

Specification:
- MT7628N (580 MHz)
- 64 MB RAM
- 8 MB FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet
- 1x LED

Flash instruction:

The only way to flash the image in TL-WR802N v4 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr802n-v4-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
   the router and keep button pressed for around 10 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Marcel Jost <majo@icutech.ch>
2019-02-28 11:26:10 +01:00
Thomas Vincent-Cross
a915ad8464 ramips: use generic board detection for Wavlink WL-WN575A3
Bring Wavlink WL-WN575A3 in line with other Wavlink ramips devices.

Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
2019-02-28 11:26:10 +01:00
Thomas Vincent-Cross
25c0b41901 ramips: various Wavlink WL-WN575A3 fixes
* assign pinmux groups to gpio function for LEDs/buttons
* rename flash node to be more generic in line with other device nodes
* remove useless/incorrect eeprom property from wmac node
* correct base mac address for embedded switch

Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
2019-02-28 11:26:10 +01:00
Aleksander Jan Bajkowski
00d89b4a89 sunxi: add support for Orange Pi One
CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz
GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0)
Memory: 512MB DDR3 (shared with GPU)
Onboard: Storage TF card (Max. 64GB) / MMC card slot
Onboard header: SPI, I2C, GPIO, UART
USB 2.0: One USB 2.0 HOST, One USB 2.0 OTG

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2019-02-26 23:20:04 +01:00
David Bauer
4ecf2ee4a0 ath79: fix support-list for TP-Link WDR3600
The TP-Link WDR3600 shares the same machine-code in the ar71xx target,
thus expecting "tl-wdr4300" not "tl-wdr3600" in the support-list
metadata to allow non-forced sysupgrades from ar71xx to ath79.

With this, it is possible to flash a WDR4300 image on the WDR3600. It
is no problem however, as the only difference is the 5GHz WiFi chip
which has 3SS instead of 2SS. Both work with either image.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-02-26 23:20:04 +01:00
David Bauer
5568c8a9fe ath79: add ar71xx support-list entry for Fritz4020
This adds the support-list entry the AVM FRITZ!Box 4020 expects in the
ar71xx target to allow non-forced sysupgrades from ar71xx to ath79.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-02-26 23:20:04 +01:00
Andreas Ziegler
53c46b504c ar71xx: GL.iNet AR300M family: correct LED definitions
remove USB as this is no LED but power control
rename WiFi LED with correct color red (like in stock firmware)
set middle LED to be used for LAN link/activity

Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
2019-02-26 23:20:04 +01:00
Piotr Dymacz
c568c6dc09 ipq40xx: add support for ALFA Network AP120C-AC
ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm
IPQ4018 + QCA8075 platform.

Specification:

- Qualcomm IPQ4018 (717 MHz)
- 256 MB of RAM (DDR3)
- 16 MB (SPI NOR) + 128 MB (SPI NAND) of flash
- 2x Gbps Ethernet, with 802.3af PoE support in one port
- 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922)
- 3x U.FL connectors
- 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas
- Atmel/Microchip AT97SC3205T TPM module (I2C bus)
- TI CC2540 Bluetooth LE module (USB 2.0 bus)
- 4x LED (all driven by GPIO)
- 1x button (reset)
- 1x USB 2.0 (optional, not installed in indoor version)
- DC jack for main power input (12 V)
- UART header available on PCB (2.0 mm pitch)

Flash instruction:

1. This board uses dual-image feature (128 MB NAND is divided into two
   64 MB partitions: 'rootfs1' and 'rootfs2').
2. Before update, make sure your device is running firmware no older
   than v1.1 (previous versions have incompatible U-Boot).
3. Use 'factory' image in vendor GUI or for sysupgrade tool, without
   preserving settings.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-02-26 00:16:22 +01:00
Piotr Dymacz
99f72c0d62 ipq40xx: add support for Macronix MX35LF1GE4AB SPI NAND
Without a proper SPI NAND support (SPI NAND framework is available in
kernel >= 4.19) the only way to make such flash working is to include
it in raw/parallel NAND subsystem support and combine with mt29f staging
driver. Obviously, this approach isn't going to be accepted by upstream
(similar support for Winbond W25N01GV was rejected).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-02-26 00:15:38 +01:00
Koen Vandeputte
f20fea9dcd kernel: bump 4.19 to 4.19.25
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-25 17:33:16 +01:00
Koen Vandeputte
ceed0665cc kernel: bump 4.14 to 4.14.103
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-25 17:33:16 +01:00
Koen Vandeputte
151d806c78 kernel: bump 4.9 to 4.9.160
Refreshed all patches.

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-25 17:33:16 +01:00
Stijn Tintel
ffc65a80d1 kernel: add missing config symbols
The addition of kmod-input-touchscreen-ads7846 enabled
INPUT_TOUCHSCREEN, which exposes several other symbols on various
targets. Add those symbols to the generic kernel configs to fix build.

Fixes: 77a54bbf13 ("kernel: add kmod-input-touchscreen-ads7846")
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-02-25 15:46:10 +02:00
Stijn Tintel
77a54bbf13 kernel: add kmod-input-touchscreen-ads7846
This module adds support for ADS7846 based touchscreens used in devices
like the WaveShare 3.5" and 4" LCD displays designed for Raspberry Pi.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-02-24 01:17:01 +02:00
Stijn Tintel
9f4a7de48a kernel: add kmod-fb-tft
This module adds support for small TFT LCD display modules. While this
module also exists in the 4.9 kernel, we are not going to support this
kernel in the next major release, so don't make it available for 4.9.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-02-24 01:15:22 +02:00
Koen Vandeputte
d9ab3240a5 kernel: bump 4.19 to 4.19.24
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-22 10:53:42 +01:00
Koen Vandeputte
3a2668c6d5 kernel: bump 4.14 to 4.14.102
Refreshed all patches.

Remove upstreamed:
- 272-uapi-if_ether.h-prevent-redefinition-of-struct-ethhd.patch

Remove upstreamed hunks:
- 080-pinctrl-msm-fix-gpio-hog-related-boot-issues.patch

Fixes:
- CVE-2018-1000026

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-22 10:53:42 +01:00
Koen Vandeputte
8f980a8cfe kernel: bump 4.9 to 4.9.159
Refreshed all patches.

Remove upstreamed:
- 023-1-smsc95xx-Use-skb_cow_head-to-deal-with-cloned-skbs.patch
- 023-6-ch9200-use-skb_cow_head-to-deal-with-cloned-skbs.patch
- 023-7-kaweth-use-skb_cow_head-to-deal-with-cloned-skbs.patch
- 050-usb-dwc2-Remove-unnecessary-kfree.patch
- 092-netfilter-nf_tables-fix-mismatch-in-big-endian-syste.patch
- 272-uapi-if_ether.h-prevent-redefinition-of-struct-ethhd.patch

Fixes:
- CVE-2018-1000026

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-22 10:53:42 +01:00
Koen Vandeputte
26f8644510 kernel: bump 3.18 to 3.18.135
Refreshed all patches.

Fixes:
- CVE-2019-3819
- CVE-2019-7221
- CVE-2019-7222

Compile-tested on: adm5120
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-22 10:53:42 +01:00
Chuanhong Guo
3bd871ad52 ath79: fix wmac memory region for qca953x
According to /arch/mips/include/asm/mach-ath79/ar71xx_regs.h
the size of wmac register range for qca953x is only 0x20000.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-02-20 18:51:31 +01:00
Linus Walleij
c72b1d8468 gemini: Generate harddisk image for DNS-313
This makes OpenWrt build an Ext2+Ext4 partitioned image
for the D-Link DNS-313 with two blank partitions, a boot
partition on /dev/sda3 and a rootfs partition on
/dev/sda4.

This uses the methods already used in apm821xx including
the tricks to convert the generated Ext2 filesystem
partition to version 1 so that the firmware bootloader
will properly recognize it.

We patch a bit around the build files to make sure we
get the rootfs size set and that genext2fs is properly
built.

Tested on the D-Link DNS-313.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[Fixing and tricksing]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-02-20 18:51:31 +01:00
Christian Lamparter
a69e101ed1 ipq40xx: speed up ath10k-caldata extraction
Reading and writing to and from flash storage is slow and currently,
the ath10kcal_extract() scripts are even more at an disadvantage
because they use a block size of 1 to be able skip.

This patch reworks the extraction scripts to be much faster and
efficient by reading and writing the calibration data in possibly
one big block.

before: (Tested on a RT-AC58U, which has SPI-NAND).

 # time dd if=/dev/ubi0_1 of=/lib/firmware/... bs=1 skip=4096 count=12064
12064+0 records in
12064+0 records out
real    0m 0.28s
user    0m 0.02s
sys     0m 0.24s

after:

 # time dd if=/dev/ubi0_1 of=/lib/firmware/... bs=12064 skip=4096 count=1 iflag=skip_bytes
1+0 records in
1+0 records out
real    0m 0.01s
user    0m 0.00s
sys     0m 0.00s

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-20 18:51:19 +01:00
Pawel Dembicki
02644e5612 generic: kernel: Add missing config option
DRM packages break modules compilation for sunxi target,
cortexa7 and cortexa8 subtargets.

This patch add missing symbol to generic config.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-02-19 22:11:29 +01:00
Yousong Zhou
afe00a79ee armvirt: 32: enable CONFIG_ARM_LPAE
This is required for running armvirt_32 on QEMU 3.0 [1], otherwise the
kernel will emit the following complaint and virtio-net-pci devices will
fail to be initialized

        [    1.124214] OF: PCI: host bridge /pcie@10000000 ranges:
        [    1.125093] OF: PCI:    IO 0x3eff0000..0x3effffff -> 0x00000000
        [    1.125942] OF: PCI:   MEM 0x10000000..0x3efeffff -> 0x10000000
        [    1.126403] OF: PCI:   MEM 0x8000000000..0xffffffffff -> 0x8000000000
        [    1.127748] pci-host-generic 4010000000.pcie: can't claim ECAM area [mem 0x10000000-0x1fffffff]: address conflict with /pcie@10000000 [mem 0x10000000-0x3efeffff]
        [    1.129752] pci-host-generic: probe of 4010000000.pcie failed with error -16

Running QEMU with "-M virt,highmem=off" is an option, but "highmem" was only
introduced as a default on flag since QEMU 2.5.0 and QEMU will fail and quit on
encounter of unknown flags

 [1] Armv7 guest fails to boot with qemu-3.0.0-1,
     https://bugzilla.redhat.com/show_bug.cgi?id=1633328#c5

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2019-02-19 13:13:49 +00:00
Yousong Zhou
0aedf5cfcb armvirt: 32: refresh kernel config
The diff was genereated by running the following command without
actually changing any kernel config options

	make kernel_menuconfig CONFIG_TARGET=subtarget

Here are some initial findings on the change

 - CONFIG_ARCH_OPTIONAL_KERNEL_RWX is now arch default
 - CONFIG_ARM_GIC_V3_ITS is selected by CONFIG_ARCH_VIRT
 - CONFIG_CPU_SPECTRE is select by CONFIG_CPU_V7
 - CONFIG_TIMER_OF is now a arch default
 - CONFIG_TIMER_PROBE is select by CONFIG_TIMER_OF

The following options should probably be moved to generic config

 - CONFIG_MIGRATION is a default on option
 - CONFIG_TREE_SRCU is a default on option for !PREEMPT && SMP system
 - CONFIG_RCU_NEED_SEGCBLIST

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2019-02-19 13:13:48 +00:00
Paul Wassi
d42c9ce326 kirkwood: add kernel 4.19 support
Add patches for 4.19
Drop patch 200-disable-tso, as the packet corruption was fixed in
kernel commit 3b89624ab54b9dc2d92fc08ce2670e5f19ad8ec8

Restructure the DTS for Marvell switch in 104-ea3500 and 105-ea4500
to fix DTC warning.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-17 19:22:39 +01:00
Lucian Cristian
e711fd48be x86: video: disable buildtin amdgpu DRM driver
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2019-02-17 19:22:39 +01:00
Lucian Cristian
cb3798cf3f x86: DRM: add x64 subtarget support
copy settings from generic subtarget

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2019-02-17 19:22:39 +01:00
Lucian Cristian
edb21ee3d2 x86: video: disable builtin radeon DRM driver
builtin driver can't access the /lib/firmware while booting,
module driver will be able to read and load the firmware files

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2019-02-17 19:22:39 +01:00
Yangbo Lu
5d11672d07 kernel: disable CONFIG_USB_IMX21_HCD in default for kernel 4.14
CONFIG_USB_IMX21_HCD should be handled in generic config and
module package. So moved it into generic config.
This also fixed build issue (kernel config question) of layerscape
armv8_32b since it also used ARCH_MXC.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[Deactivate CONFIG_USB_IMX21_HCD also for kernel 4.19]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-02-17 19:22:39 +01:00
Oskari Lemmela
cd1e9c88f3 sunxi: fix: A64 unstable timer
Backport A64 unstable timer patches from linux 5.1

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
[Split the single patch into the two original patches]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-02-17 19:22:39 +01:00
Pawel Dembicki
d5f615bf2a sunxi: add support for Sinovoip Banana Pi M2 Plus
CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz
GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0)
Memory: 1GB DDR3 (shared with GPU)
Onboard: Storage TF card (Max. 64GB) / MMC card slot
Onboard: Network 10/100M Ethernet RJ45 (Realtek RTL8211E)
Onboard: Network BT4.0/WiFi 802.11 b/g/n (Ampak AP6212)
Onboard header: SPI, I2C, GPIO, UART
USB 2.0: Two USB 2.0 HOST, One USB 2.0 OTG

Untested:
Audio, Video

Not working:
Bluetooth

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-02-17 19:22:39 +01:00
Tomasz Maciej Nowak
55b808e0c4 x86: image: add test module to bootloader
It was previously added in 546fced, which was part of "intel-microcode:
load as early as possible" series.
Unfortunately the conditionals added to GRUB config caused error on boot,
because on sysupgrade, bootloader is not updated and is left with old
features/modules. Since this module is needed for early microcode load
and transition to this needs to be done step by step, enable the test
module now, so that every newly created image has it already embedded.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-02-17 18:22:40 +01:00
Tomasz Maciej Nowak
bb0e4f9fb0 build: remove leftovers from previous x86 commits
VBoxManage is not used and the image is created with proper permisions:
0f5d0f6  image: use internal qemu-img for vmdk and vdi images drop host
         dependencies on qemu-utils and VirtualBox

Unreachable config symbols:
9e0759e  x86: merge all geode based subtargets into one

No need to define those symbols since x86_64 is subtarget of x86:
196fb76  x86: make x86_64 a subtarget instead of a standalone target

Unreachable config symbols, so remove GRUB_ROOT:
371b382  x86: remove the xen_domu subtarget

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-02-17 18:22:40 +01:00
Adrian Schmutzler
319c5d7c49 ar71xx: Fix 5 GHz MAC address for Archer C60 v2
Looks like C60 v2 needs the MAC address to be calculated
manually, while the C60 v1 gets it correctly without manual
interference.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-02-17 18:22:39 +01:00
Rosen Penev
5e8f18fef6 kernel: Remove CONFIG_UDF_NLS for kernel 4.19
kernel 4.18 removed the symbol and made NLS implicit.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2019-02-17 17:33:18 +01:00
Koen Vandeputte
ca13820d13 kernel: bump 4.19 to 4.19.23
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-15 21:53:27 +01:00
Koen Vandeputte
3967376eb7 kernel: bump 4.14 to 4.14.101
Refreshed all patches.

Fixes:
- CVE-2019-3819

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-15 21:53:27 +01:00
Oever González
c35d7f3f8a ipq40xx: fix ipq40xx_setup_macs for Linksys EA6350v3
This commit fixes the script that sets the MAC address of the LAN
switch. The LAN MAC address should be the WAN MAC address plus one.

Without this patch the WAN and the LAN interface will use the same
MAC address and an error will be generated.

With this patch all interfaces will have a different MAC address,
consecutive in the following order: WAN, LAN, radio0 and radio1.

Signed-off-by: Oever González <notengobattery@gmail.com>
2019-02-14 16:56:15 +01:00