Avoid flooding the log with the message below by increasing the log
level to debug:
mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The patch was rejected by upstream. The mtk_nand driver should be
modified to support the mt7621 flash controller instead. As there is no
newer version to backport, or no upstream version to fix bugs, let's
move the driver to the files dir under the ramips target. This makes it
easier to make changes to the driver while waiting for mt7621 support to
land in mtk_nand.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Modified the radio frequency hardware part of e2600ac c1/c2,
need to cooperate with the modified board.bin file, the device
can work normally.
Signed-off-by: 张 鹏 <sd20@qxwlan.com>
This commit replaces patch number 0703 with the upstream accepted
version. This patch requires backporting an additional patch to
avoid conflicts.
The only significant change is the lower maximum MTU. Packets with
lengths over 2400 may be dropped.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit moves the patches for the r8152.c driver to the generic
directory. Previously they were only available on the bcm27xx target.
With these patches the Realtek RTL8153C, RTL8153D, RTL8156A and RTL8156B
chips are supported on all targets by the kmod-usb-net-rtl8152 module.
The RTL8156A and RTL8156B are the 2.5Gb/s Ethernet adapters.
The patches have been tested on TP-Link UE300 (RTL8153A) and UNITEK
1313B (RTL8156B).
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This reverts commit 80b7a8a7f5.
Now that 5.10 is the default kernel for all platforms, we can
bring back the NU801 userspace driver for platforms that rely
on it. Currently it's used on the MX100 x86_64 target, but
other Meraki platforms use this controller.
Note that we also now change how we load nu801. The way we did
this previously with procd worked, but it meant it didn't load
until everything was up and working.
To fix this, let's call nu801 from boot and re-trigger the
preinit blink sequence. Since nu801 runs as a daemon this is
now something we can do.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
(removed empty line, currently only MX100 uses it so: @TARGET_x86)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This model, also know as "1&1 HomeServer", shares the same features as 7530.
The vendor firmware has artificial software limitations: only 2 of the 4
LAN-Ports are GBit, and the USB-Host is only v2.0.
With OpenWrt, USB is already working at v3.0.
Signed-off-by: Andre Heider <a.heider@gmail.com>
(updated commit message to reflect current state)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Google WiFi (codename: Gale) is an IPQ4019-based AP, with 2 Ethernet
ports, 2x2 2.4+5GHz WiFi, 512 MB RAM, 4 GB eMMC, and a USB type C port.
In its stock configuration, it runs a Chromium OS-based system, but you
wouldn't know it, since you can only manage it via a "cloud" +
mobile-app system.
The "v2" label is coded into the bootloader, which prefers the
"google,gale-v2" compatible string. I believe "v1" must have been
pre-release hardware.
Note: this is *not* the Google Nest WiFi, released in 2019.
I include "factory.bin" support, where we generate a GPT-based disk
image with 2 partitions -- a kernel partition (using the custom "Chrome
OS kernel" GUID type) and a root filesystem partition. See below for
flashing instructions.
Sysupgrade is supported via recent emmc_do_upgrade() helper.
This is a subtarget because it enables different features
(FEATURES=boot-part rootfs-part) whose configurations don't make sense
in the "generic" target, and because it builds in a few USB drivers,
which are necessary for installation (installation is performed by
booting from USB storage, and so these drivers cannot be built as
modules, since we need to load modules from USB storage).
Flashing instructions
=====================
Documented here:
https://openwrt.org/inbox/toh/google/google_wifi
Note this requires booting from USB storage.
Features
========
I've tested:
* Ethernet, both WAN and LAN ports
* eMMC
* USB-C (hub, power-delivery, peripherals)
* LED0 (R/G/B)
* WiFi (limited testing)
* SPI flash
* Serial console: once in developer mode, console can be accessed via
the USB-C port with SuzyQable, or other similar "Closed Case
Debugging" tools:
https://chromium.googlesource.com/chromiumos/third_party/hdctools/+/master/docs/ccd.md#suzyq-suzyqable
* Sysupgrade
Not tested:
* TPM
Known not working:
* Reboot: this requires some additional TrustZone / SCM
configuration to disable Qualcomm's SDI. I have a proposal upstream,
and based on IRC chats, this might be acceptable with additional DT
logic:
[RFC PATCH] firmware: qcom_scm: disable SDI at boot
https://lore.kernel.org/linux-arm-msm/20200721080054.2803881-1-computersforpeace@gmail.com/
* SMP: enabling secondary CPUs doesn't currently work using the stock
bootloader, as the qcom_scm driver assumes newer features than this
TrustZone firmware has. I posted notes here:
[RFC] qcom_scm: IPQ4019 firmware does not support atomic API?
https://lore.kernel.org/linux-arm-msm/20200913201608.GA3162100@bDebian/
* There's a single external button, and a few useful internal GPIO
switches. I haven't hooked them up.
The first two are fixed with subsequent commits.
Additional notes
================
Much of the DTS is pulled from the Chrome OS kernel 3.18 branch, which
the manufacturer image uses.
Note: the manufacturer bootloader knows how to patch in calibration data
via the wifi{0,1} aliases in the DTB, so while these properties aren't
present in the DTS, they are available at runtime:
# ls -l
/sys/firmware/devicetree/base/soc/wifi@a*/qcom,ath10k-pre-calibration-data
-r--r--r-- 1 root root 12064 Jul 15 19:11 /sys/firmware/devicetree/base/soc/wifi@a000000/qcom,ath10k-pre-calibration-data
-r--r--r-- 1 root root 12064 Jul 15 19:11 /sys/firmware/devicetree/base/soc/wifi@a800000/qcom,ath10k-pre-calibration-data
Ethernet MAC addresses are similarly patched in via the ethernet{0,1} aliases.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
(updated 901 - x1pro moved in the process)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
See my upstream questions:
https://lore.kernel.org/linux-arm-msm/20200913201608.GA3162100@bDebian/
This effectively reverts upstream Linux commit 13e77747800e ("firmware:
qcom: scm: Use atomic SCM for cold boot"), because Google WiFi boot
firmwares don't support the atomic variant.
This fixes SMP support for Google WiFi.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
See firmware-utils.git commits [1], which implemented the cros-vbutil
verified-boot payload-packing tool, and extended ptgen for the CrOS
kernel partition type. With these, it's now possible to package kernel +
rootfs to make disk images that can boot a Chrome OS-based system (e.g.,
Chromebooks, or even a few AP models).
Regarding PARTUUID= changes: Chromium bootloaders work well with a
partition number offset (i.e., relative to the kernel partition), so
we'll be using a slightly different root UUID line.
NB: I've made this support specific to ip40xx for now, because I only
plan to support an IPQ4019-based AP that uses a Chromium-based
bootloader, but this image format can be used for essentially any
Chromebook, as well as the Google OnHub, a prior Chromium-based AP using
an IPQ8064 chipset.
[1]
ptgen: add Chromium OS kernel partition support
https://git.openwrt.org/?p=project/firmware-utils.git;a=commit;h=6c95945b5de973026dc6f52eb088d0943efa96bb
cros-vbutil: add Chrome OS vboot kernel-signing utility
https://git.openwrt.org/?p=project/firmware-utils.git;a=commit;h=8e7274e02fdc6f2cb61b415d6e5b2e1c7e977aa1
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
From a manufacturer's image (version R89-13729.57.27), with appopriate
',variant=' appended to the board names:
$ .../qca-swiss-army-knife/tools/scripts/ath10k/ath10k-bdencoder \
-i ./board-google_wifi.qca4019
FileSize: 48596
FileCRC32: 3966df5d
FileMD5: d54161b0fb9e93691c4272649c37535a
BoardNames[0]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=GO_GALE'
BoardLength[0]: 12064
BoardCRC32[0]: e117f336
BoardMD5[0]: ea35e78c88a8571201da8b75edc9b881
BoardNames[1]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=GO_GALE'
BoardLength[1]: 12064
BoardCRC32[1]: 6c751ec9
BoardMD5[1]: 44cbc4ca6cb7141ba4249615f7065582
BoardNames[2]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=GO_BREEZE'
BoardLength[2]: 12064
BoardCRC32[2]: 24fba117
BoardMD5[2]: b4ac055b3ab67d5a6f5607a96af39a1f
BoardNames[3]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=GO_BREEZE'
BoardLength[3]: 12064
BoardCRC32[3]: a3e16b2a
BoardMD5[3]: 8b26cb285032314247304114b8ac50e7
Naming follows existing Google projects included in upstream board-2.bin
-- GO(ogle) prefix, an underscore (_), and the project code name, all in
caps.
Note that I only tested the "gale" model; the "breeze" model is a later
revision (same marketing name) with very small hardware changes but
otherwise using the same firmware image.
Submitted upstream here:
ath10k-firmware: QCA4019: hw1.0: Add Google Wifi BDFs
http://lists.infradead.org/pipermail/ath10k/2022-March/013465.htmlhttps://lore.kernel.org/ath10k/YjaNGW252Ls%2FyDw8@localhost/
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tel(co Electronics) X1 Pro is preventing ipq40xx generic
from building due to the KERNEL_SIZE.
Whenever bigger kernels are possible, if lzma is supported
is unknown.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Fixes compilation under musl based distros like Alpine Linux.
Also add pcre/host as a build dependency as it's needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Required to allow sysupgrades from OpenWrt 19.07.
Closes#7071
Fixes: 98fbf2edc0 ("ath79: move TPLINK_HWID/_HWREV to parent for tplink-safeloader")
Tested-by: J. Burfeind <git@aiyionpri.me>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some configure scripts look for msgfmt and gmsgfmt. As we don't install
the latter, configure might pick up one from staging_dir/hostpkg, and
the other from the host:
checking for msgfmt... /home/stijn/Development/OpenWrt/openwrt/staging_dir/hostpkg/bin/msgfmt
checking for gmsgfmt... /usr/bin/gmsgfmt
This could potentially lead to hard to debug undefined behaviour.
Install a symlink in the host install phase to avoid this.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
When using external targets there is a symlink being created for the
target under target/linux which then becomes dangling under Image
Builder. Fix it by dereferencing the possible symlink.
Tested on IB with external target, ipq40xx and mvebu.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It is disabled in the generic kernel config and not used in any of the
other targets. There was no specific reason for enabling it, so let's be
consistent and remove it from the qoriq kernel config.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
As the LED controller is working now, we can make good use of the LEDs
now.
- Drop the model-name prefix
- Rename eth0 / eth1 LEDs to LAN1 / LAN2, as they are labeled as such
on the casing
- Enable wired LEDs in userspace
Signed-off-by: David Bauer <mail@david-bauer.net>
Move the GPIO extender to the SoC node. Otherwise, the legacy PowerPC
init code will not populate the BUS and thus never probe spi-gpio.
Signed-off-by: David Bauer <mail@david-bauer.net>
Evaluating the return value of 'json_load' didn't work in the
intended way resulting in PIN status no longer being read on modems
where --get-pin-status doesn't fail.
Fix this by trying --get-pin-status first and checking if pin1_status
field exists in JSON, and if it doesn't try again with
--uim-get-sim-state.
Fixes: #9501
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
While it hasn't always been clear whether the "AP" is part of the model
name on the Ubiquiti website, we include it for all other pre-AC
variants (AP Pro and the AP Outdoor+). Add it to the original UniFi AP
as well for consistency.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Tavis has just reported, that he was recently trying to track down a
reproducible crash in a compressor. Believe it or not, it really was a
bug in zlib-1.2.11 when compressing (not decompressing!) certain inputs.
Tavis has reported it upstream, but it turns out the issue has been
public since 2018, but the patch never made it into a release. As far as
he knows, nobody ever assigned it a CVE.
Suggested-by: Tavis Ormandy <taviso@gmail.com>
References: https://www.openwall.com/lists/oss-security/2022/03/24/1
Signed-off-by: Petr Štetiar <ynezz@true.cz>
* only map filesystems configured in 'loadables'
* allow mapping more than one filesystem (e.g. customization/branding
or localization in addition to rootfs)
* small cleaning here and there
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
engine.mk is supposed to be included by engine packages, but it will not
be present in the SDK in the same place as in the main repository.
Move it to include/openssl-engine.mk to avoid this.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
860ca90 odhcpd: Support for Option NTP and SNTP
83e14f4 router: advertise removed addresses as invalid in 3 consecutive RAs
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Albeit a separate crypto module, lzo-rle uses the same kernel library as lzo.
Crypto API users (zram, for example) expect both lzo and lzo-rle to be
available, so let's include lzo-rle (about 5.5 kiB) in the lib-lzo package.
Based on e9hack's original patch: https://patchwork.ozlabs.org/project/openwrt/patch/541cbfbd-76f2-59b3-a867-47b6f0fc7da9@gmail.com/
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
If the selected boot configuration is stored by U-Boot in '/chosen'
node as 'bootconf' attribute, use that configuration to resolve the
block device used as rootfs. Fall back to use the default configuration
in case 'bootconf' is not present.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
