Add minimalistic tool to allow releasing /dev/fit* devices which is
needed on sysupgrade when using the fitblk driver.
The package is hidden in menuconfig, it should only be selected by
adding it to the default package selection of boards using it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make use of recently added UBI support in MediaTek's ARM
TrustedFirmware-A on new MT7988 SoC.
Load fip from static UBI volume instead of fixed offset on SPIM-NAND
and SNFI.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hide arm-trusted-firmware-mediatek packages from interactive config.
Exposing them only causes confusion and needed variants are anyway
selected as dependencies by uboot-mediatek packages.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that Malibu (QCA807x) PHY-s use an upstream driver we dont need support
for defining address of the first PHY in the package so drop the patch.
Signed-off-by: Robert Marko <robimarko@gmail.com>
PoE devices in the realtek target have the possibility to add PSE info
to the board description via 02_network. Make this available for all
targets, by moving the uci_set_poe() function to the globally available
uci-default.sh script.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Drop deprecated Xiaomi LEDs quirk patches as they are not needed anymore
as LEDs are now supported by the upstream qca807x driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
If a PHY doesn't use the integrated driver, SSDK use poll the phydev to
get the real PHY mode. qca807x use PSGMII as PHY mode and this specific
mode is not detected in qca SSDK while used in the entire driver.
Add support for it in the hsl_port_phydev_interface_mode_status_get
function used to translate PHY mode to the internal SSDK value.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Disable Malibu PHY driver in Qca SSDK in favor of the upstream version.
The same workaround are applied and the version upstream is just a drop
in replacement and is well tested from the ipq40xx target.
Also using the upstream version permits further support for LEDs.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
IPQ60xx uses a different codename for SSDK, so lets pass the correct one
as otherwise SSDK asumes we are building for the old MIPS SoC-s.
Signed-off-by: Robert Marko <robimarko@gmail.com>
[ drop outdated commit description info ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Checking for AP_VLAN misdetects ath10k-ath12k as fullmac, because of software
crypto limitations. Check for monitor mode support instead, which is more
reliable.
Fixes: https://github.com/openwrt/openwrt/issues/14575
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- introduce 'DirectInterface' option to bind exactly to specified interface;
fixes#9666 and late IPv4/IPv6 address assignment
- option 'DirectInterface' takes precedence over 'Interface'
- improve interface/address handling,
e.g. verify count of listening endpoints due to dropbear limit (10 for now)
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
- correct maximum receive window size
- adjust receive window size against maximum allowed value
- warn about too high receive window size in syslog
improves f95eecfb
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
end users should have done this since OpenWrt 19.07.
if they didn't do this yet - perform auto-transition.
schedule 'rsakeyfile' removal for next year release.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
these options allow one to configure U2F/FIDO support in more granular way
inspired by upstream commit aa6559db
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
reduces binary/package size and increases overall performance
also:
- adjust 910-signkey-fix-use-of-rsa-sha2-256-pubkeys.patch
to build without DROPBEAR_RSA/DROPBEAR_RSA_SHA256
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
hmac-sha1 and diffie-hellman-group14-sha1 are weak algorithms.
A future deprecation notice of ssh-rsa (2048-bit) has been issued. [1]
It has no place in a potentially internet-facing daemon like dropbear.
Upstream has acknowledged this and offered this solution to disable
these two until this is made to be the default in the next release
of dropbear next year. [2]
1. https://www.openssh.com/txt/release-8.2
2. https://github.com/mkj/dropbear/issues/138
Signed-off-by: John Audia <therealgraysky@proton.me>
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
- "default n" is not needed: options are not selected by default
- wrap config on 80 characters width (assuming tab is 8 characters long)
- add feature cost size and security notes for DROPBEAR_AGENTFORWARD
and DROPBEAR_DBCLIENT_AGENTFORWARD:
describe why and where it should be disabled
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
- switch DB_OPT_COMMON and DB_OPT_CONFIG to comma-separated lists:
this allows to have values with "|" in DB_OPT_COMMON and DB_OPT_CONFIG
which is more likely to be than values with commas;
use $(comma) variable for values with commas.
- sort DB_OPT_COMMON and DB_OPT_CONFIG to have "overrides" on top of list.
- allow DB_OPT_COMMON to have values with commas.
- allow to replace multiline definitions in sysoptions.h.
improves e1bd9645
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
- update dropbear to latest stable 2022.83;
for the changes see https://matt.ucc.asn.au/dropbear/CHANGES
- drop patches:
- 001-fix-MAX_UNAUTH_CLIENTS-regression.patch
- rework patches:
- 901-bundled-libs-cflags.patch
- refresh remaining patches
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Bind to the configured system interfaces only. Switchport interfaces
are no longer ignored and uci interface values for LLDPD are honored.
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
