As we're now going to pad all images by default to 128MiB let's enable
compression of the images for armvirt and malta in order to save some
space and bandwidth.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
As we're now going to pad all images by default, lets decrease the
default rootfs partition size from 256MiB to 128MiB in order to save
some space.
I'm keeping it above 100MiB in order to keep current behavior, where
overlay filesystem is using F2FS.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It's being used only in x86 target to produce combined images, where
it's mandatory to have padded images in order to produce working
squashfs combined images usable in QEMU.
Currently we're producing unusable x86 combined squashfs images
(18.06.1, 18.06.2 and snapshots) as we don't enable TARGET_IMAGES_PAD,
thus providing very small space for the overlay filesystem, leading to
the following with OpenWrt 18.06.1 r7258-5eb055306f images on x86 QEMU:
root@(none):/# mount | egrep 'root|overlay'
/dev/root on /rom type squashfs
/dev/loop0 on /overlay type ext4
overlayfs:/overlay on / type overlay
root@(none):/# df -h | egrep 'root|overlay|Size'
Filesystem Size Used Available Use% Mounted on
/dev/root 2.5M 2.5M 0 100% /rom
/dev/loop0 113.0K 8.0K 97.0K 8% /overlay
overlayfs:/overlay 113.0K 8.0K 97.0K 8% /
So we should rather ensure proper image padding in image generation code
and we shouldn't rely on config options in order to generate usable
images.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit eae6cac6a3 ("lantiq: add support for AVM FRITZ!Box 7362 SL"), but
one needs an initramfs image to flash OpenWrt from stock firmware (as
described in the commit log). This patch has the initramfs image built
by default.
Thanks to blogic (for pointing to the FEATURES declaration in the target
Makefiles) and Musashino on the forum for suggesting
config/Config-images.in needed editing too. While at it, reorder the
TARGET_INITRAMFS_COMPRESSION_LZMA declarations alphabetically.
This patch will result in initramfs images for all lantiq subtargets
that have the ramdisk flag set. I tested on the falcon and ase
subtargets, which lack that flag, to confirm they don't produce any
initramfs images with this patch - which they do not.
Given the limited scope of the lantiq (sub)target(s), blogic indicated
this should be OK.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[fixed the wrong reference to eae6cac6a3 commit]
VBoxManage is not used and the image is created with proper permisions:
0f5d0f6 image: use internal qemu-img for vmdk and vdi images drop host
dependencies on qemu-utils and VirtualBox
Unreachable config symbols:
9e0759e x86: merge all geode based subtargets into one
No need to define those symbols since x86_64 is subtarget of x86:
196fb76 x86: make x86_64 a subtarget instead of a standalone target
Unreachable config symbols, so remove GRUB_ROOT:
371b382 x86: remove the xen_domu subtarget
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This patch adds the boot-part feature which enables the brcm2708
target move from the custom boot partition size config option to
the generic CONFIG_TARGET_KERNEL_PARTSIZE.
Note:
For people using custom images: Just like with
CONFIG_TARGET_ROOTFS_PARTSIZE changing the value
can cause sysupgrade to repartition the device!
Make sure to have a backup in this case.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds the boot-part feature to the apm82181 sata target.
This makes it possible to configure the boot partition size with
the generic CONFIG_TARGET_KERNEL_PARTSIZE symbol.
Please note: For people using custom images: Just like with
CONFIG_TARGET_ROOTFS_PARTSIZE changing the value can cause
sysupgrade to repartition the device!
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The sdcard image generation uses CONFIG_TARGET_ROOTFS_PARTSIZE, which is
currently bound to TARGET_ROOTFS_EXT4FS on this target.
Since the rootfs is squashfs anyway, allow deselecting of the ext4fs
one.
Sort the target list alphabetically while here.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Extend the small_flash feature to disable swap, core dumps, and
kernel debug info, and change the squashfs block size to 1024KiB.
Also change squashfs fragment cache to 2 for small_flash to ease memory
usage.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Symbol CONFIG_INITRAMFS_FORCE allows to ignore the value passed by the
bootloader.
By default, all symbols containing INITRAMFS are wiped from the final
config and then re-added conditionally.
Add support for this symbol, as the build will stop otherwise
questioning the user about this option:
* Restart config...
*
*
* General setup
*
Cross-compiler tool prefix (CROSS_COMPILE) []
Compile also drivers which will not load (COMPILE_TEST) [N/y/?] n
...
Initial RAM filesystem and RAM disk (initramfs/initrd) support
(BLK_DEV_INITRD) [Y/n/?] y
Initramfs source file(s) (INITRAMFS_SOURCE) []
Ignore the initramfs passed by the bootloader (INITRAMFS_FORCE)
[N/y/?] (NEW)
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The following patch enables building of initramfs images by default for
the P1020 subtarget in mpc85xx.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
On the more sophisticated (i.e. deeper FIFO) serial controllers,
flow-control might be needed to avoid dropping output.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Prior to commit 1496b95a0 ("x86: clean up default grub baudrate
settings") we had three different baud rates for the Geode targets:
19200 for net5501, 38400 for alix2, and 115200 for Geos.
It doesn't seem that there's a very good reason for varying from our
default 115200 baud, so let's make the Geode target do that instead.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2 GB is overkill and was only added to allow unlimited ext4 resizing,
which is a pretty rare use case. 256 MB allows resizing up to 256 GB,
which should be good enough for almost all users.
A lot of this is mostly irrelevant anyway, since you can just use
squashfs + ext4 overlay.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The current default rootfs size of 256MB in conjunction with 4K blocks
produces an ext4 filesystem which lacks the appropriate amount of backup GDT
entries to support online-resizing.
For x86 targets, increase the default rootfs size to 2048MB which allows
online resizing the filesystem to up to 2TB which is the current theoretical
maximum for LEDE, due to missing GPT support on the root block device.
Note that the filesystem artefact will not occupy 2GB on the build system as
the make_ext4fs utility uses sparse files to generate the filesystem images,
so the actual disk usage is much lower. Furthermore the filesystem images
are gzip compressed, shrinking them to only a few megabytes on the download
server.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Michael Heimpold <mhei@heimpold.de>
There is very little practical use to limit the number of available inodes on
an ext4 filesystem and the make_ext4fs utility is able to calculate useful
defaults by itself.
Drop the option to make resulting ext4 filesystems more flexible by default.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Michael Heimpold <mhei@heimpold.de>
Added gen_mvebu_sdcard_img.sh to facilitate creating an fixed-size sdcard image,
adding the bootloader and populating it with actual data.
Added the required rules for creating a 4GB sdcard image according to this layout:
p0: boot (fat32)
p1: rootfs (squashfs)
p2: rootfs_data (ext4)
This should be generic to any mvebu boards that can boot from block storage.
Added the new sdcard image to the Clearfog image profile.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup]
The MR24's u-boot takes it sweet time decompressing the
LZMA-packed initramfs image. A user reported that
compared to the old gzip method in v2: it "takes a ton
longer to decompress like 4\x the old boot time for
decompression".
This patch also fixes a issue with the WNDR4700's initramfs
image getting to big and causing the following u-boot crash
during the decompression:
"Uncompressing Multi-File Image ... Error: inflate() returned -5
out-of-mem or overwrite error - must RESET board to recover"
This patch fixes both issues by reverting the MR24's initramfs
compression method back to gzip. And choosing to compress the
initramfs within the initramfs image as LZMA by default.
Cc: chrisrblake93@gmail.com
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
If jffs2 support was not enabled by the target, jffs2 are quite likely
to be broken, so we shouldn't build them.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This changes the x86 image generation to match x86_64, using the PARTUUID for
the rootfs instead of explicitly configuring the device.
It unbreaks KVM with VirtIO, which uses /dev/vda2 instead of /dev/sda2.
Tested in QEMU/KVM with VirtIO, VirtualBox and VMware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44966
Non-functional changes to config/Config-*.in files, including:
* spelling mistakes
* inconsistent terminology
* grammar
* overly long lines in "help" components
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
SVN-Revision: 42519
