Use the same Yafut code revision for both updating devices with NAND
flash and preparing firmware images for devices with NOR flash.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
Link: https://github.com/openwrt/openwrt/pull/13453
Signed-off-by: Robert Marko <robimarko@gmail.com>
Dual-slot NAS based on Marvell Kirkwood.
Specifications:
- Marvell 88F6702 @1GHz
- 256Mb RAM
- 128Mb NAND
- 1x GbE LAN (Marvell 88E1318R)
- 1x USB 2.0
- 2x SATA
- Weltrend WT69P3 ("supervisor" MCU chip)
- Serial on J2 (115200,8n1)
- Newer bootROM so kwboot-ing via serial is possible
Notes:
- The Weltrend MCU is controlled by the package added in utils/dns320l-mcu.
- The original MAC address is stored in the "mini firmware" image's first
17 bytes.
- Compared to the original MTD layout, the uImage+rootfs are now stored in
a common ubi partition.
Installation:
1. Serial console
- Connect your levelshifter to the serial console
on J2 (refer to the wiki page for pinout)
2. Update u-boot
- Download the u-boot.kwb image for the device
- Powercycle the NAS
- Run "kwboot -b u-boot-dns320l/u-boot.kwb /dev/ttyUSB0 -p"
- Connect to the serial console with minicom
- tftp 0x0800000 u-boot-dns320l/u-boot.kwb
(Please note that "PHY reset timed out" seems to be customary
on kirkwood devices, the egiga0 interface works regardless.)
- nand erase 0x0 100000
- nand write 0x0800000 0x0 0x100000
- reset
3. Install OpenWrt
- Boot up the initramfs image
- tftpboot 0x800000 openwrt-kirkwood-generic-dlink_dns320l-initramfs-uImage; bootm 0x800000
- Download the sysupgrade image and perform sysupgrade
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
This 4G/LTE modem is a WiFi hotspot, and also works as cdc_ether modem
when plugged over USB. It needs usb-modeswitching. With HuaweiNewMode,
it will modeswitch from 3426:1f01 (mass-storage) to 3426:14db
(cdc_ether).
Signed-off-by: Didier 'OdyX' Raboud <odyx@raksha.ch>
Link: https://github.com/openwrt/openwrt/pull/15497
Signed-off-by: Robert Marko <robimarko@gmail.com>
The 'nandbiterrs' tool is useful to find out of bit error correction of
NAND is working as expected by deliberately introducing bit errors and
telling up to which number they can be corrected.
Enable build of the testing tools and package the 'nandbiterrs' tool as
part of the nand-utils package.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Changes:
- new URL for sources (old address is dead)
- daemon and utils from packages feed are merged in here
- only build once
- no need to update at the same time in both places
- update to v3.1.4
- removed unneeded patches
- added audisp-syslog
- removed audispd (no longer exists)
- rename and move to package/utils/audit
- update new path in one dependent package
Signed-off-by: Marius Dinu <m95d+git@psihoexpert.ro>
With the switch to ZSTD for git clone packaging, hashes have changed so
fixup remaining package hashes that were missed in the inital update.
Fixes: b3c1c57 ("treewide: update PKG_MIRROR_HASH to zst")
Signed-off-by: Robert Marko <robimarko@gmail.com>
When using zst instead of xz, the hash changes. This commit fixes the
hash for packages and tools in core.
Signed-off-by: Paul Spooren <mail@aparcar.org>
With the change in version schema the downloaded files changed, too,
mostly the hash is now prefixed with a tilde `~` instead of a dash `-`.
Since each downloaded archive contains folder with the same name as the
archive, the checksum changed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Different from OPKG, APK uses a deterministic version schema which chips
the version into chunks and compares them individually. This enforces a
certain schema which was previously entirely flexible.
- Releases are added at the very and end prefixed with an `r` like
`1.2.3-r3`.
- Hashes are prefixed with a `~` like `1.2.3~abc123`.
- Dates become semantic versions, like `2024.04.01`
- Extra tags are possible like `_git`, `_alpha` and more.
For full details see the APK test list:
https://gitlab.alpinelinux.org/alpine/apk-tools/-/blob/master/test/version.data
Signed-off-by: Paul Spooren <mail@aparcar.org>
this patch separates libe2p from e2fsprogs package, like all other
provided libraries are their own packages. Also some development headers
were missing so I added those along with pkg-config files.
Signed-off-by: Oskari Rauta <oskari.rauta@gmail.com>
Add minimalistic tool to allow releasing /dev/fit* devices which is
needed on sysupgrade when using the fitblk driver.
The package is hidden in menuconfig, it should only be selected by
adding it to the default package selection of boards using it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It appears `md5` is no longer state of the art. Let's switch it to
something slightly newer to increase security.
Suggested-by: abnoeh <abnoeh@mail.com>
Signed-off-by: Paul Spooren <mail@aparcar.org>
The raspberypi/userland repository has been deprecated and the RPi tools have
been moved to the raspberrypi/utils repository.
96a7334ae9
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This is the last update for bcm27xx-userland as it has been
deprecated but funcional up to raspberry pi 5.
96a7334 README: Update to make it clear that most code in this repo is deprecated
3c97f76 userland: dtoverlay: /boot/firmware is a valid path
153a235 Assorted clang static analysis fixes
eca070c bcm_host: Update kms/fkms check for pi5
06a7618 dtoverlay: Support bcm2712 as a platform
0489c07 dtoverlay: Add dtoverlay_first/next_subnode
a1c7f81 dtoverlay: Support literal assignments of path strings
44a3953 raspivid: Also flush PTS file if flush is enabled
cc1ca18 userland: dtoverlay: Use os_prefix if set
9d5250f libfdt: Add null-ptr check for prop-data to resolve clang --analyzer warning
50527c6 mmal: Only include Videocore components if not running on Videocore
df245ea tvservice: Update unsupported message to recommend kmsprint
de0cfe8 dtoverlay: Fix clang warnings
0182f05 dtoverlay: Fix various compiler warnings
2a6306b dtoverlay: Fix path rebasing and exports
d1e92d7 dtoverlay: Add support for string escape sequences
b1ee39e gencmd: Add a fallback to mailbox interface if vchiq is not available
54fd97a hello_pi: Fix some build issues
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Setting up usb gadgets using g_* kernel modules are considered a
legacy approach, but the usb_gadget configfs is a bit annoying
to use directly.
The usb_gadget configfs works by creating magic directories
and writing to magic files under /sys/kernel/config/usbgadget.
This new package is an init script to setup usb_gadget configfs
using uci. In the config file, gadget/configuration/function
sections create corresponding directories. UCI options are magic
files available in the configfs and strings/0x409 directories,
grabbed with a 'find' command. UDC option in gadget writes
the UDC file under the 'gadget' directory to attach the
generated gadget config.
It's also possible to apply pre-made config templates under
/usr/share/usbgadget. The templates use the same UCI config
format, with the 'gadget' entry named 'g1'. Currently, there
are templates for CDC-ACM and CDC-NCM gadgets written based
on existing g_*.ko module code.
Certain SBCs come with only a USB device port (e.g. Raspberry Pi
Zero). With this script, it's now possible to perform initial
setup on them by adding a default NCM gadget.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Fix typo calling lua53 instead of lua5.3 for Package Default definition.
This cause only missing description of the package and doesn't cause
any build regression.
Fixes: c52ca08d40 ("lua5.3: build shared library")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Let ucode-mod-* packages select the ucode interpreter instead of depending
on it to avoid recursive dependency chains in unrelated packages.
Fixes: https://github.com/openwrt/packages/issues/22837
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This fixes the mirror hash to the version of the file uploaded to the
download mirror and which my build calculated.
Fixes: b117e7244f ("firmware-utils: update to Git HEAD (2023-11-21)")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
1d42292d8063 tplink-safeloader: Add TP-Link Archer A6 V3.20
3338f5389d72 tplink-safeloader: add TL-WPA8635P v3
17ca5eeb1c10 tplink-safeloader: add TL-WPA8631P v4
f730ad2fa0b4 bcmblob: new tool for reading Broadcom's BLOBs
cb1ddac98124 firmware-utils: fix typo in error message when no OpenSSL library found
916633160dc9 bcmclm: new tool for reading Broadcom's CLM data
a2d49fb1e188 tplink-safeloader: add RU support-list entry for Archer C6U v1
bb12cf5c3fa9 tplink-safeloader: Add support for TP-Link Deco M5 The special_id values are the same for EU and Asian models, and they apply to all models: v1, v2, and v3. They are not sorted as they are currently in the same order as extracted from the official firmware image.
9e2de8515be1 tplink-safeloader: add EAP610 v3 and EAP613 v1
a170683c0e11 firmware-utils: fix use of NULL string progname
89875fc18b57 tplink-safeloader: CPE510: add Canadian support
9e211d2980fe mktplinkfw2: add support to extract bootloader images
c18f662f3c74 mktplinkfw2: add support to pack bootloader
3dc133915f87 mktplinkfw2: show exact exceed bytes when the image is to big
d16ff798d58a tplink-safeloader: WPA8631: add v4 AU, US
0fa1cc51013f zytrx: add LTE5398-M904
635466123429 firmware-utils: ptgen: add SiFive GPT partition support
ba5bc4e1ae9d add dlink-sge-image for D-Link devices by SGE
3b114de29cf7 lxlfw: move code opening LXL to helper function
8e149e480391 lxlfw: move code copying data to helper function
16fa89076122 lxlfw: fix struct lxl_hdr attribute
d770cab82e58 lxlfw: support embedding blobs
eaf2ea28dbe6 lxlfw: support extracting image
12bf1a99bd6e lxlfw: support certificate & signature blobs
Fixes: https://github.com/openwrt/openwrt/issues/12939
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Information about package license is important, so lets add it.
Fixes: 79ee0d2cee ("debugcc: add new package to debug IPQ based SoC clocks")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
I find myself manually compiling dtc as a staticly linked binary rather
often while porting a new device to OpenWrt as dtc is rarely included in
various vendor modifications of OpenWrt.
So, since dtc offers a convenient meson option to build it as staticaly
linked binary, lets make it a compile time option.
Signed-off-by: Robert Marko <robimarko@gmail.com>
0352a33 uloop: support new interval and signal APIs
1468cc4 syntax: don't treat `as` and `from` as reserved keywords
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Store the private key with read and write permission for the user only
and not with read permissions for everyone. This converts the
write_file() function from fopen() to open() because open allows to
specify the permission mask of the newly created file. It also adds and
fixes some existing error handling.
OpenSSL does this in the same way already.
With this change it looks like this:
root@OpenWrt:/# ls -al /etc/uhttpd.*
-rw-r--r-- 1 root root 749 Nov 6 23:14 /etc/uhttpd.crt
-rw------- 1 root root 121 Nov 6 23:14 /etc/uhttpd.key
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Store the private key with read and write permission for the user only
and not with read permissions for everyone. This converts the
write_file() function from fopen() to open() because open allows to
specify the permission mask of the newly created file. It also adds and
fixes some existing error handling.
OpenSSL does this in the same way already.
With this change it looks like this:
root@OpenWrt:/# ls -al /etc/uhttpd.crt /etc/uhttpd.key
-rw-r--r-- 1 root root 519 Nov 6 22:58 /etc/uhttpd.crt
-rw------- 1 root root 121 Nov 6 22:58 /etc/uhttpd.key
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes building with USE_LTO enabled.
<artificial>:(.text+0xcc8): relocation R_MIPS16_26 against `luaL_argerror' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol strcpy
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
Remove ABI version, since its format is not accepted by the linker.
Enable rpath to avoid clash with system libraries
Signed-off-by: Felix Fietkau <nbd@nbd.name>
1) clear nvram partialboots upon successful boot
This behavior is already defined for EA9500; enabled for EA9200 too.
2) fix MAC address in board.d/02_network
Use the correct nvram variable to derive lan/wan MAC address.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Add missing PKG_MIRROR_HASH. This is always needed as is used to
generate and use a tar instead of git clone and validate the hash of it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The PKG_CPE_ID links to NIST CPE version 2.2.
Assign PKG_CPE_ID to all remaining package which have a CPE ID.
Not every package has CPE id.
Related: https://github.com/openwrt/packages/issues/8534
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
350b960 add support for multi GNSS solutions
fb87d0f ugps: add baud rate command line option
a8171a0 main.c: -S does not take any options
Build-tested: ramips/ltap-2hnd
Run-tested: ramips/ltap-2hnd
Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
Hardware
--------
CPU: Mediatek MT7981
RAM: 512M DDR4
FLASH: 256M NAND
ETH: MaxLinear GPY211 (2.5GbE N Base-T)
WiFi: Mediatek MT7981 (2.4GHz 2T2R:2 5GHz 3T3R:2 802.11ax)
BTN: 1x Reset
LED: 1x Multi-Color
UART Console
------------
Available below the rubber cover next to the ethernet port.
Settings: 115200 8N1
Layout:
<12V> <LAN> GND-RX-TX-VCC
Logic-Level is 3V3. Don't connect VCC to your UART adapter!
Installation Web-UI
-------------------
Upload the Factory image using the devices Web-Interface.
As the device uses a dual-image partition layout, OpenWrt can only
installed on Slot A. This requires the current active image prior
flashing the device to be on Slot B.
In case this is not the case, OpenWrt will boot only one time, returning
to the ZyXEL firmware the second boot.
If this happens, first install a ZyXEL firmware upgrade of any version
and install OpenWrt after that.
Installation TFTP / Recovery
----------------------------
This installation routine is especially useful in case of a bricked
device.
Attach to the UART console header of the device. Interrupt the boot
procedure by pressing Enter.
The bootloader has a reduced command-set available from CLI, but more
commands can be executed by abusing the atns command.
Boot a OpenWrt initramfs image available on a TFTP server at
192.168.1.66. Rename the image to nwa50axpro-openwrt-initramfs.bin.
$ atnf nwa50axpro-openwrt-initramfs.bin
$ atna 192.168.1.88
$ atns "192.168.1.66; tftpboot; setenv fdt_high 0xffffffffffffffff;
bootm"
Upon booting, set the booted image to the correct slot:
$ zyxel-bootconfig /dev/mtd9 get-status
$ zyxel-bootconfig /dev/mtd9 set-image-status 0 valid
$ zyxel-bootconfig /dev/mtd9 set-active-image 0
Copy the OpenWrt sysupgrade image to the device using scp.
Write the sysupgrade image to NAND using sysupgrade.
$ sysupgrade -n image.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
colrm is already built, package just isn't generated.
colrm can be used to remove columns from file/stdin.
Use cases vary, personally I needed it because I build openwrt
natively - and wolfssl configure script wants either colrm, or cut
but busybox's cut isn't accepted.
Built: x86_64, latest git
Tested: x86_64, latest git
Signed-off-by: Oskari Rauta <oskari.rauta@gmail.com>
Safely detect integer overflow in try_addint() and try_subint().
Old code relied on undefined behavior, and recent versions of GCC on x86
optimized away the if-statements.
This caused integer overflow in Lua code instead of falling back to
floating-point numbers.
Signed-off-by: Adam Bailey <aebailey@gmail.com>
commit c0611b45a9 ("e2fsprogs: symlink e2fsck to fsck.ext{2, 3, 4},
and tune2fs to findfs") introduced a symlink from tune2fs to findfs.
This only works when the included private libblkid library is used, but
commit 5b1660a538 ("utils/e2fsprogs: Update to 1.43.6") disabled the
usage of this private lib and enabled the shared lib support.
Removing this symlink makes it possible to install tune2fs and findfs
package.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
It's required by bcm53xx. This allows dropping separated oseama package
and avoids some code duplication.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Some of firmware utils may be required on target devices. It's useful
e.g. for dealing with some firmware formats. That is often required
(supporting specific format) to provide an option to revert to original
firmware.
So far we had packaged "otrx" util only for use on Broadcom targets.
Refactor that to package the whole firmware-utils project so we can
package any single util needed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Release Notes:
http://lists.busybox.net/pipermail/busybox-cvs/2023-May/041510.html
Refresh commands, run after busybox is first built once (nothing changed
compared to 1.36.0):
cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-mipsel_24kc_musl/busybox-default/busybox-1.36.1
cd ..
./convert_defaults.pl ../../../build_dir/target-mipsel_24kc_musl/busybox-default/busybox-1.36.1/.config > Config-defaults.in
Manual edits needed afterward:
* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
BUSYBOX_DEFAULT_FEATURE_IPV6
* Config-defaults.in: OpenWrt config TARGET_bcm53xx logic applied to
BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)
* Config-defaults.in: OpenWrt logic applied to
BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)
* Config-defaults.in: correct the default ports that get reset
BUSYBOX_DEFAULT_FEATURE_HTTPD_PORT_DEFAULT 80
BUSYBOX_DEFAULT_FEATURE_TELNETD_PORT_DEFAULT 23
* config/editors/Config.in: Add USE_GLIBC dependency to
BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)
* config/shell/Config.in: change at "Options common to all shells" the conditional symbol
SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
(discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
Apparently our script does not see the hidden option while
prepending config options with "BUSYBOX_CONFIG_" which leads to a
missed dependency when the options are later evaluated.)
* Edit a few Config.in files by adding quotes to sourced items in
config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014f)
Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Nick Hainke <vincent@systemli.org>
The getrandom syscall is not hanging at bootup any more if there is
not enough entropy. This was fixed upstream in 2018 in commit:
a9cf659e05
This OpenWrt patch is not needed any more.
This reverts commit e64463ebde ("util-linux: avoid using the getrandom syscall")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes the following error:
* check_data_file_clashes: Package taskset wants to install file build_dir/target-powerpc_8548_musl/root-mpc85xx/usr/bin/taskset
But that file is already provided by package * busybox
* opkg_install_cmd: Cannot install package taskset.
Fixes: 3c3d797c4d ("busybox: enable taskset by default")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove upstramed patches:
- 100-configure.ac-fix-AC_ARG_WITH.patch
- 101-configure.ac-fix-cross-compilation.patch
Remove deprecated f2fstat tool:
https://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs-tools.git/commit/?id=77bf7ed29f1dd1341079913f3b36fc62f812c4f5
Changelog:
06c027a f2fs-tools: upgrade version 1.16.0
542cc57 fsck.f2fs: fix sanity check logic for cp_payload
a7df89e mkfs.f2fs: remove indentation
c82985a fsck.f2fs: don't call report_zone on normal partition
0ac168e f2fs-tools: relax zone size of power of 2
641be32 mkfs.f2fs: trim all the devices except the first one
3835fef f2fs-tools: fix # of total segments
5b08ca9 f2fs_io: support AES_256_HCTR2
ae3301c f2fs_io: Fix out of tree builds
ddbde27 fsck.f2fs: relocate chksum verification step during f2fs_do_mount()
77bf7ed f2fs-tools: Remove deprecated f2fstat
fb6575e Remove sg_write_buffer
1bb669e fsck.f2fs: avoid uncessary recalculation
ccd2361 fsck.f2fs: fix potential overflow of copying i_name
cd6b133 fsck.f2fs: add parentheses for SB_MASK
399600a dump.f2fs: remove unavailable option -g
3e6e178 f2fs-tools: define HAVE_CLOCK_GETTIME properly
907b972 f2fs-tools: support F2FS_IOC_START_ATOMIC_REPLACE
9ff70fb f2fs-tools: give less overprovisioning space
844f821 f2fs-tools: set host-aware zoned device similar to host-managed one
88ac76d fsck.f2fs: fix missing to assign c.zoned_model
8cbe34e fsck.f2fs: trigger repairing if filesystem has inconsistent errors
2f1dde2 fsck.f2fs: trigger repairing if filesystem was forced to stop
465159f fsck.f2fs: export valid image size
3486b62 mkfs.f2fs: update allocation policy for ro feature
bdd51e5 fsck.f2fs: fix __end_block_addr()
5a5e419 Always use sparse/sparse.h when building for Android
19f77c6 f2fs-tools: fix build error on lz4-1.9.4
986c1f1 Fix format strings in log messages
0d6acbe fsck.f2fs: use elapsed_time in checkpoint for period check
9b7a4c5 mkfs.f2fs: catch total_zones=0 instead of crashing
6148db3 f2fs-tools: use F2FS_BLKSIZE instead of PAGE_*_SIZE
f09c2b7 f2fs_io: support triggering filesystem GC via ioctl
32e7d27 configure.ac: fix cross compilation
65fe94e configure.ac: fix AC_ARG_WITH
6325cf7 Use F2FS_BLKSIZE as the size of struct f2fs_summary_block
c89be7a Use F2FS_BLKSIZE for dev_read_block() buffers
5317d18 Improve compile-time type checking for f2fs_report_zone()
92e2e52 Fix f2fs_report_zone()
648a491 Fix the struct f2fs_dentry_block definition
c964547 resize.f2fs: add option to manually specify new overprovision
a741438 fsck.f2fs: drop compression bit if inline_data is set
406b1c9 f2fs-tools: fix cannot get bdev information
9d0cb9e f2fs_io: add dsync option for write
a7b8b46 tools: fix file too large causing overflow
bddca6f dump.f2fs: add -I nid to dump inode by scan full disk
ebc3879 android_config: add time headers
c1144bf Check fallthrough in mount.h for Mac
bcb9929 avoid unnecessary function
7d902f4 Fix dependencies on linux/blkzoned.h when using Bionic.
274abbb Remove unnecessary config.h
8c97ab3 libzone: remove duplicate header
adcec10 Support zoned device if libc exists
efc2bc7 mkfs.f2fs: fix typo
3034a41 mkfs.f2fs: split unused parameter
dd8d8e5 f2fs-tools: do not use SG_IO in Android
4f216e6 f2fs-tools: move android_config before defining them
48c5dbb f2fscrypt: adjust config file first
4b55459 android_config: add missing uuid library
Signed-off-by: Nick Hainke <vincent@systemli.org>
This fixes the build of util-linux on powerpc and arc. Both CPU
architectures were not supported here in addition to the missing MIPS
support.
Fixes: 628a410ed1 ("util-linux: update to 2.39")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
8f78aff2cb68 ubus: support multiple call return values
51f4dba67313 ucode: also link libresolv if ns_initparse() is not found
5c7d07773a59 uci: fix ctx.commit() without arguments
5163867269fc Merge pull request #148 from jow-/uci-fix-commit
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Based on Paul Fertser <fercerpav@gmail.com>'s guidance:
Change AUTORELEASE in rules.mk to:
```
AUTORELEASE = $(if $(DUMP),0,$(shell sed -i "s/\$$(AUTORELEASE)/$(call commitcount,1)/" $(CURDIR)/Makefile))
```
then update all affected packages by:
```
for i in $(git grep -l PKG_RELEASE:=.*AUTORELEASE | sed 's^.*/\([^/]*\)/Makefile^\1^';);
do
make package/$i/clean
done
```
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
_LARGEFILE64_SOURCE has to be defined in the source, or CFLAGS can be used
to pass -D_LARGEFILE64_SOURCE to allow to keep using LFS64 definitions.
Fixes error in the form of:
restripe.c: In function 'restore_stripes':
restripe.c:758:43: error: 'off64_t' undeclared (first use in this function); did you mean 'off_t'?
758 | (off64_t)read_offset) {
| ^~~~~~~
| off_t
restripe.c:758:43: note: each undeclared identifier is reported only once for each function it appears in
restripe.c:758:51: error: expected ')' before 'read_offset'
758 | (off64_t)read_offset) {
| ^~~~~~~~~~~
| )
restripe.c:757:36: note: to match this '('
757 | if (lseek64(source, read_offset, 0) !=
| ^
make[3]: *** [Makefile:193: restripe.o] Error 1
Fixes: fff878c5bc ("toolchain/musl: update to 1.2.4")
Signed-off-by: Nick Hainke <vincent@systemli.org>
musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces and
autotools failed to check the lseek64 function.
Force enable ac_cv_func_lseek64 to workaround it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces and
autotools failed to check the lseek64 function.
Force enable ac_cv_func_lseek64 to workaround it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The resize tool will resize the prompt to match the current terminal
size. This is helpful when connecting to the system using UART to make
the vi or top output match the current terminal size.
This increases the busybox binary size by 136 bytes and the ipkg size by
335 bytes on aarch64.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commit 9d96b6fb72 ("ath79/mikrotik: disable building NAND images")
disabled building images for MikroTik devices with NAND flash due to a
less than satisfactory method used for updating the kernel on those
devices back then.
To address the problem, add support for updating the kernel on MikroTik
devices with NAND flash using a new tool, Yafut, which enables copying
files from/to Yaffs file systems even if the kernel does not have native
support for the Yaffs file system compiled in. Instead of erasing the
entire NAND partition holding the kernel during every system upgrade
(which is what the previously-used approach employing kernel2minor
involved), Yafut preserves the Yaffs filesystem present on that
partition and only replaces the kernel executable. This allows bad
block information to be preserved across sysupgrade runs and also
enables wear leveling on the NAND partition holding the kernel. Yafut
does not rely on kernel2minor in any way and intends to eventually
supersede the latter for NAND devices.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
I found use for this in my scripts; I noticed that it is already
compiled with util-linux - there just isn't package for it -
let's package it then.
Description:
The rev utility copies the specified files to the standard output,
reversing the order of characters in everyline.
Signed-off-by: Oskari Rauta <oskari.rauta@gmail.com>
This reduces open coding and allows to easily add a knob to enable
it treewide, where chosen packages can still opt-out via "no-lto".
Some packages used LTO, but not the linker plugin. This unifies 'em
all to attempt to produce better code.
Quoting man gcc(1):
"This improves the quality of optimization by exposing more code to the
link-time optimizer."
Also use -flto=auto instead of -flto=jobserver, as it's not guaranteed
that every buildsystem uses +$(MAKE) correctly.
Signed-off-by: Andre Heider <a.heider@gmail.com>
This reduces open coding and allows to easily add a knob to
enable it treewide, where chosen packages can still opt-out via
"no-gc-sections".
Note: libnl, mbedtls and opkg only used the CFLAGS part without the
LDFLAGS counterpart. That doesn't help at all if the goal is to produce
smaller binaries. I consider that an accident, and this fixes it.
Note: there are also packages using only the LDFLAGS part. I didn't
touch those, as gc might have been disabled via CFLAGS intentionally.
Signed-off-by: Andre Heider <a.heider@gmail.com>
This splits the code in 4 files:
- uencrypt.h
- uencrypt.c - main program
- uencrypt-openssl.c - OpenSSL/wolfSSL implementation
- uencrypt-mbedtls - mbedTLS implementation
Other changes, accounting for ~400 bytes increase in ipk size:
- more error condition checking and reporting,
- hide key and iv command line arguments
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This commit includes some additional changes:
- better handling of iv and keys in openssl/wolfssl variants
- fix compiler warnings and whitespace
- build all 3 variants as separate packages
- adjust the new package name in targets' DEVICE_PACKAGES
- remove PKG_FLAGS:=nonshared
[Beeline SmartBox Flash - OK]
Tested-by: Mikhail Zhilkin <csharper2005@gmail.com>
[after test: replaced a hardcoded IV size of 16 by cipher_info->iv_size]
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Changelog:
039a994 Bump version to v1.7.0
3f29d6d pylibfdt: add size_hint parameter for get_path
2022bb1 checks: Update #{size,address}-cells check for 'dma-ranges'
abbd523 pylibfdt: Work-around SWIG limitations with flexible arrays
a41509b libfdt: Replace deprecated 0-length arrays with proper flexible arrays
2cd89f8 dtc: Warning rather than error on possible truncation of cell values
55778a0 libfdt: tests: add get_next_tag_invalid_prop_len
7359034 libfdt: prevent integer overflow in fdt_next_tag
035fb90 libfdt: add fdt_get_property_by_offset_w helper
98a0700 Makefile: fix infinite recursion by dropping non-existent `%.output`
a036cc7 Makefile: limit make re-execution to avoid infinite spin
c6e9210 libdtc: remove duplicate judgments
e37c256 Don't generate erroneous fixups from reference to path
5045465 libfdt: Don't mask fdt_get_name() returned error
e64a204 manual.txt: Follow README.md and remove Jon
f508c83 Update README in MANIFEST.in and setup.py to README.md
c2ccf8a Add description of Signed-off-by lines
90b9d9d Split out information for contributors to CONTRIBUTING.md
0ee1d47 Remove Jon Loeliger from maintainers list
b33a73c Convert README to README.md
7ad6073 Allow static building with meson
fd9b8c9 Allow static building with make
fda71da libfdt: Handle failed get_name() on BEGIN_NODE
c7c7f17 Fix test script to run also on dash shell
01f23ff Add missing relref_merge test to meson test list
ed31080 pylibfdt: add FdtRo.get_path()
c001fc0 pylibfdt: fix swig build in install
26c54f8 tests: add test cases for label-relative path references
ec7986e dtc: introduce label relative path references
651410e util: introduce xstrndup helper
4048aed setup.py: fix out of tree build
ff5afb9 Handle integer overflow in check_property_phandle_args()
ca72944 README: Explain how to add a new API function
c0c2e11 Fix a UB when fdt_get_string return null
cd5f69c tests: setprop_inplace: use xstrdup instead of unchecked strdup
a04f690 pylibfdt: add Property.as_*int*_array()
8310271 pylibfdt: add Property.as_stringlist()
d152126 Fix Python crash on getprop deallocation
17739b7 Support 'r' format for printing raw bytes with fdtget
45f3d1a libfdt: overlay: make overlay_get_target() public
c19a4ba libfdt: fix an incorrect integer promotion
1cc41b1 pylibfdt: Add packaging metadata
db72398 README: Update pylibfdt install instructions
383e148 pylibfdt: fix with Python 3.10
23b56cb pylibfdt: Move setup.py to the top level
69a7607 pylibfdt: Split setup.py author name and email
0b106a7 pylibfdt: Use setuptools_scm for the version
c691776 pylibfdt: Use setuptools instead of distutils
5216f3f libfdt: Add static lib to meson build
4eda259 CI: Cirrus: bump used FreeBSD from 12.1 to 13.0
0a3a9d3 checks: Add an interrupt-map check
8fd2474 checks: Ensure '#interrupt-cells' only exists in interrupt providers
d8d1a9a checks: Drop interrupt provider '#address-cells' check
52a16fd checks: Make interrupt_provider check dependent on interrupts_extended_is_cell
37fd700 treesource: Maintain phandle label/path on output
e33ce1d flattree: Use '\n', not ';' to separate asm pseudo-ops
d24cc18 asm: Use assembler macros instead of cpp macros
ff3a30c asm: Use .asciz and .ascii instead of .string
5eb5927 fdtdump: fix -Werror=int-to-pointer-cast
0869f82 libfdt: Add ALIGNMENT error string
69595a1 checks: Fix bus-range check
72d09e2 Makefile: add -Wsign-compare to warning options
b587787 checks: Fix signedness comparisons warnings
69bed6c dtc: Wrap phandle validity check
9102211 fdtget: Fix signedness comparisons warnings
d966f08 tests: Fix signedness comparisons warnings
ecfb438 dtc: Fix signedness comparisons warnings: pointer diff
5bec74a dtc: Fix signedness comparisons warnings: reservednum
24e7f51 fdtdump: Fix signedness comparisons warnings
Remove upstreamed:
- 0001-Support-r-format-for-printing-raw-bytes-with-fdtget.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
* Fix incorrect error message in case input file opening fails
* Don't close files in case the pointers are invalid
Signed-off-by: David Bauer <mail@david-bauer.net>
