* Refreshed patches.
* Removed patches:
- target/linux/ar71xx/patches-4.9/103-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch superseded by upstream
- target/linux/ar71xx/patches-4.9/403-mtd_fix_cfi_cmdset_0002_status_check.patch superseded by upstream
- target/linux/brcm63xx/patches-4.9/001-4.11-01-mtd-m25p80-consider-max-message-size-in-m25p80_read.patch accepted upstream
- target/linux/brcm63xx/patches-4.9/001-4.15-08-bcm63xx_enet-correct-clock-usage.patch accepted upstream
- target/linux/brcm63xx/patches-4.9/001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch accepted upstream
- target/linux/generic/pending-4.9/900-gen_stats-fix-netlink-stats-padding.patch
* New backported patch to address ext4 breakage, introduced in 4.9.112:
- backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch
Also add ARM64_SSBD symbol to ARM64 targets still running kernel 4.9
Thanks to Koen Vandeputte for pointing out the need to add the ARM64_SSBD symbol, and the ext4 patch.
Compile-tested on: ar71xx
Run-tested on: ar71xx
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
This is a new & warm feature that allows nesting partiitons in DT and
mixing their types (e.g. static vs. dynamic). It's very useful for
boards that have most partitions static but some of them require extra
parsing (e.g. a "firmware" partition).
It's required to successfully backport support for new devices using
that new syntax in their DT files.
Since brcm63xx has a custom alternative patch the upstream one is being
reverted for it. The plan is to make brcm63xx use the upstream
implementation.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 2a598bbaa3)
THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 67a3cdcbb0)
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit bdc2b58c4b)
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit a08b0d0c31)
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 978543a246)
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit ead26e9db6)
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit f928c338ad)
- DGND3700v1: fix port numbers, they're in reverse order
- FaST2704n: there is no WAN port identified as such, only 4 LAN
- AD1018: configure the "FIBRE" port as WAN
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
(cherry picked from commit fbbb977772)
Refreshed all patches
Added new ARM64 symbol: ARM64_ERRATUM_1024718
Compile-tested on: ar71xx
Runtime-tested on: ar71xx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This bumps the 4.4. kernel in master to 4.4.119.
Includes more Meltdown & Spectre mitigation.
* Refresh patches.
* Refresh x86/config for RETPOLINE.
* Deleted 8049-PCI-layerscape-Add-fsl-ls2085a-pcie-compatible-ID.patch (accepted upstream)
* Deleted 8050-PCI-layerscape-Fix-MSG-TLP-drop-setting.patch (accepted upstream)
* Deleted 650-pppoe_header_pad.patch (does not apply anymore (code was replaced)).
Bumps from 4.4.112 to 4.4.115 were handled by Kevin Darbyshire-Bryant.
Compile-tested on: ar71xx & oxnas.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Rosen Penev <rosenp@gmail.com>
The root= parameter overrides the automatic rootfs detection by partition
name, so drop it. Fixes boot from flash after renumeration changes of
partitions due to parser changes.
Fixes FS#1350.
Fixes: a27d59bb42 ("brcm63xx: switch to new partition layout specification")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for kernel 4.9 based on the more upstream comformant
partition defintions. Increases compressed kernel size by ~95k
compared to 4.4.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Partitions are supposed to be enclosed in an extra partitions node. Allow
the bcm63xxpart parser to cope with that.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The lookup needs to be called just "reset" for the common code.
Fixes: 054c0d4e31 ("brcm63xx: backport mdio-bus reset gpio support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The status led part was missed when changing the board name to *-nor.
Fixes: e12c72bb52 ("brcm63xx: Add Sercomm AD1018 support")
Reported-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Backport the mdio-bus reset gpio support from 4.12 and use it instead
of toggling the reset ourself.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for the Sercomm AD1018 router
This a BCM6328 based board, 128 MB RAM, 128 MiB NAND flash,
with an onboard BCM43217 wifi, 4 ethernet ports and 1 USB
host port (not soldered). The board also has an FXS chip (Si32177)
connected via SPI (SS2#), without support in LEDE.
Since NAND flash chips aren't still supported in brcm63xx, the
support is for now added to work only with SPI flash chips. Therefore
hardware modding, soldering a new SPI flash chip, is required
to make the board work with LEDE (tested and working OK).
The flash at dts is intentionally left without partitioning to let
the user choose a NOR chip of any size (8, 16 or 32 MB).
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
[jonas.gorski: renamed ad1018 to ad1018-nor to signify the modification]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The bcm6368 pinctrl driver passed the wrong variable to
devm_regmap_field_alloc, causing it to blow up when later trying to
access the field.
Fixes#1211.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for the Comtrend AR-5315u router
This a BCM6318 based board, 64 MB RAM, 16 MB SPI flash,
with an onboard BCM43217 wifi, 4 ethernet ports and 1
USB host port
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
[jonas.gorski: refreshed patch]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter. Some device
drivers rely on this, and will cause an OOPS otherwise.
Fixes: FS#735
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fix incorrect offset and size of linux partition.
Fixes: 97b36aca09 ("brcm63xx: add pflash for remaining pflash equipped boards")
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
For targets using the generic board detection and board specific
settings in diag.sh, the board name is still unset at the time the
set_state() provided by diag.sh is called by 10_indicate_preinit.
Change the execution order to ensure the boardname is populated before
required the first time. Do the target specific board detection as
early as possible, directly followed by the generic one to allow a
seamless switch to the generic function for populating /tmp/sysinfo/.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The warning will be triggered by jffs2 or UBI, and partial writes are no
issue for most flash chips.
Fixes: 2a2b16210b ("brcm63xx: backport upstream solution for SPI message size limits")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
SOC: Broadcom BCM6368 (2 * Broadcom BMIPS4350 V3.1 / 400 MHz)
Flash size: 32MB (split 16/16 dual boot)
RAM size: 64MB
Wireless: BCM432x 802.11a/b/g/n(pci)
Ethernet: Broadcom BCM53115
USB: 1 x USB 2.0
Known issues:
- Unable to detect 53115 switch attached to MDIO. Not supported
- No support for the cable port
More info on the device and the research can be found at:
http://www.actiontec.com/212.html
Same FCC ID as:
https://wikidevi.com/wiki/Actiontec_V1000H_(Telus)
Signed-off-by: Anthony Sepa <anthonysepa@yahoo.ca>
[jonas.gorski: fix commit subject/message]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
