Just by running `make kernel_oldconfig` and unsetting following options
manually as those cores are cortex-a7 based and thus irrelevant for the
currently default cortex-a9 used cores.
CONFIG_CLK_IMX6SL is not set
CONFIG_CLK_IMX6SX is not set
CONFIG_CLK_IMX6UL is not set
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Turned out those are simply MBR with active boot partition. And not
needed at all on emmc. Remove them as ptgen can now generate hybrid
MBR sufficient to boot MT7622 from SD Card.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
mt7622 uses MBR partition for booting from SD card.
Add hybrid MBR entry with boot flag after PMBR entry.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Do not align partitions with sectors. Only kb align
for GPT is supported.
Use 254 heads and 63 sectors for PMBR.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Adding -H option copies partition to MBR after pmbr entry.
Max 3 partitions can be copied to MBR.
Hybrid MBR is needed only in special cases.
For example mt7622 SD card boot needs MBR entry with boot
flag enabled.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
autoconf-lean was not ready yet. Revert it until things get sorted.
This reverts commit 32c664ff02.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
These make a big difference when doing WireGuard with small armv7
routers, and the 5.4 backport already has it.
Suggested-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Without this patch, the chacha block counter is not incremented on neon
rounds, resulting in incorrect calculations and corrupt packets.
This also switches to using `--no-numbered --zero-commit` so that future
diffs are smaller.
Reported-by: Hans Geiblinger <cybrnook2002@yahoo.com>
Reviewed-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This is required for devices that use NVRAM data for detecting currently
used firmware partition (e.g. Linksys devices).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The previous approach of referencing artifacts in follow-up artifacts
can't work with parallel builds in the current way image.mk is built.
Refactor things so this is not needed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Write everything needed for eMMC install into the gaps between
partitions on SD card. In that way, installation to eMMC only needs
the SD card, no additional files need to be loaded via TFTP any more.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds the latest version of ofpart commit. It hopefully
1. Doesn't break compilation
2. Doesn't break partitioning
(this time).
It's required to implement fixed partitioning with some quirks. It's
required by bcm53xx, bcm4908, kirkwood, lantiq and mvebu.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
autotools.mk does not have any protection currently that would prevent
it from being sourced multiple times. Note that both package.mk and
host-build.mk source autotools.mk. So any package Makefile that includes
both will cause hooks to be added twice (at least twice).
This is fixed by declaring a new variable, __autotools_inc, and only
continuing if this variable doesn't equal 1. The same is done by
rules.mk already.
Also, this commit does away with an ifneq that checks PKG_FIXUP (instead
of HOST_FIXUP) for patch-libtool before adding to the host pre-configure
hook. This does not make sense.
The second ifneq is amended. The current one manually does what the
define patch_libtool_host is already doing. It can just use the define.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
This was provided by the old static config.site files and is required by
some software, i.e. freeswitch.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Don't download all of vim just to build xxd. Use a tight tarball
containing only xxd sources instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This profile is meant to be used on MT7622 rfb1 AP, indicate that in
the name to make things less confusing.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
p2p_add_device() may remove the oldest entry if there is no room in the
peer table for a new peer. This would result in any pointer to that
removed entry becoming stale. A corner case with an invalid PD Request
frame could result in such a case ending up using (read+write) freed
memory. This could only by triggered when the peer table has reached its
maximum size and the PD Request frame is received from the P2P Device
Address of the oldest remaining entry and the frame has incorrect P2P
Device Address in the payload.
Fix this by fetching the dev pointer again after having called
p2p_add_device() so that the stale pointer cannot be used.
This fixes the following security vulnerabilities/bugs:
- CVE-2021-27803 - A vulnerability was discovered in how p2p/p2p_pd.c
in wpa_supplicant before 2.10 processes P2P (Wi-Fi Direct) provision
discovery requests. It could result in denial of service or other
impact (potentially execution of arbitrary code), for an attacker
within radio range.
Fixes: 17bef1e97a50 ("P2P: Add peer entry based on Provision Discovery Request")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
At this moment driver start fail with error:
[ 3.771991] fsl,elbc-fcm-nand: probe of ffa00000.nand failed with error -22
elbc-fcm-nand driver use legacy method of ecc mode detection. It detect hw/sw
ecc mode when system configure it to "none". [1]
This patch adds 'nand-ecc-mode = "none"' propoerty to use generic driver
ecc mode detection.
[1] https://elixir.bootlin.com/linux/v5.10.18/source/drivers/mtd/nand/raw/fsl_elbc_nand.c#L730
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
At this moment p2020rdb has broken images, because NOR memory connected
to eLBC bus isn't detected.
In 642b1e8dbed7 linux tree commit, config dependencies of MTD_PHYSMAP_OF
was changed and now MTD_PHYSMAP is required.
This patch adds MTD_PHYSMAP option to kernel config in p2020 subtarget
and fix booting of p2020rdb.
Fixes: 13b1db795f ("mpc85xx: add support for kernel 5.4")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Amazon AWS T3 cloud instances require kernel support
for the Elastic Fabric Adapter to access storage
and for Elastic Network Adapter to use network
interfaces.
Since the Fabric Adapter is needed to access
root filesystem, enable in x86_64 kernel.
Elastic Network Adapter goes in a module,
and add this module to default list in x86_64.
The module is set to AutoLoad because AutoProbe does
not seem to load it.
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
Changes:
- Remove custom Build/Compile because it's no longer needed
- Remove std=gnu99 which is added automaticaly by igmpproxy if needed
- Remove -Dlog from CFLAGS because igmpproxy doesn't have log function
Signed-off-by: Jan Pavlinec <jan.pavlinec@nic.cz>
libunwind dependency check does not allow for MIPS64 arch. Add MIPS64 awareness.
libunwind seems to support MIPS64 without issues, it was limited by the dep arch
check in the Makefile.
Used to compile Suricata6/Rust locally without issue.
Signed-off-by: Donald Hoskins <grommish@gmail.com>
Non Linux systems e.g. macOS lack the __u64 type and produce build errors:
In file included from tools/aisimage.c:9:
In file included from include/image.h:19:
In file included from ./arch/arm/include/asm/byteorder.h:29:
In file included from include/linux/byteorder/little_endian.h:13:
include/linux/types.h:146:9: error: unknown type name '__u64'; did you mean '__s64'?
typedef __u64 __bitwise __le64;
Resolved by declaring __u64 in include/linux/types.h
Build tested on macOS and Ubuntu.
Signed-off-by: Georgi Valkov <gvalkov@abv.bg>
Compile and run-tested on malta/mip32be, using bpftool directly and also
libbpf (linked with tc) to inspect and load simple eBPF programs.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The latest iproute2 version brings various improvements and fixes:
https://git.kernel.org/pub/scm/network/iproute2/iproute2.git/log/?qt=range&q=v5.10.0..v5.11.0
In particular, ip and tc now use libbpf as the standard way to load BPF
programs, rather than the old, limited custom loader. This allows more
consistent and featureful BPF program handling e.g. support for global
initialized variables.
Also fix a longstanding problem with iproute2 builds where unneeded DSO
dependencies are added to most utilities, bloating their installation
footprint. From research and testing, explicitly using a "--as-needed"
linker flag avoids the issue. Update accordingly and drop extra package
dependencies from Makefile.
Additional build and packaging updates include:
- install missing development header to iproute2/bpf_elf.h
- propagate OpenWrt verbose flag during build
- update and refresh patches
Compile and run tested: QEMU/malta-mips32be on kernels 5.4 & 5.10.
All iproute2 packages were built and installed to the test image. Some
regression testing using ip-full and tc was successfully performed to
exercise several kmods, tc modules, and simple BPF programs.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Changes:
* Increase "oem" partition size from 0x10000 to 0x20000
* Correct partition lables, synchronize with official firmware
Evidence:
It should be the same as hiwifi hc5x61a and the fact indeed the
case. Here is part of dmesg boot log read from official firmware:
[ 1.470000] Creating 7 MTD partitions on "raspi":
[ 1.470000] 0x000000000000-0x000000030000 : "u-boot"
[ 1.480000] 0x000000030000-0x000000040000 : "hw_panic"
[ 1.490000] 0x000000040000-0x000000050000 : "Factory"
[ 1.490000] 0x000000fc0000-0x000000fe0000 : "oem"
[ 1.500000] 0x000000fe0000-0x000000ff0000 : "bdinfo"
[ 1.510000] 0x000000ff0000-0x000001000000 : "backup"
[ 1.510000] 0x000000050000-0x000000fc0000 : "firmware"
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Simplify cmake option handling by putting everything in blocks.
Add openssl patch as there's no easy way to disable.
Rebase the skip manpages patch.
Remove the monitor mode patch as it no longer applies.
Remove flex patch as normal Makefile is no longer used.
Remove USB path patch. While it is deprecated, the codepath is never
taken. /sys/bus/usb/devices is checked before hand. If it exists, the
function does stuff and returns. Additionally, this path is used
elsewhere in the code.
Refresh other patches.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
