tools/env/fw_env.c misses to include stdint.h.
Apparently musl doesn't mind and includes this header by default,
but glibc does not and causes the build to fail.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
In company networks everything except the http and https protocol is
often causes problems, because the network administrators try to block
everything else. To make it easier to use LEDE in company networks use
the https/http protocol for git access when possible.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Based on a submission to the uboot-lantiq repo by Eddi De Pieri.
Major cleanup and addition of brnboot second stage u-boot was done by
me.
The second stage brnboot u-boot is untested, since the brnboot prompt
is secured by a still unknown password. But should work.
The former ram values are replaced with the ram values extracted from
the original brnboot. The old ones didn't worked with the ramboot
image.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The default bootloader partition of some devices is to small for an
u-boot with uncompressed gphy firmware(s).
Instead of increasing the bootloader partition size, in compare to the
stock firmware, compress the firmware. This would allow the bootloader
of at least the FritzBox 3370 as well as the bootloader of the
VGV7510KW22 to fit into the bootloader partition of the stock firmware.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Based on a submission to the uboot-lantiq repo by Eddi De Pieri.
Devices like the xrx200 Arcadyan VGV7519 are using two NOR flash chips.
Signed-off-by: Mathias Kresin <dev@kresin.me>
According to the author, all SPI related configs are copy & paste
leftovers. Which makes sense since nothing is connected to the SPI bus
on this device.
The NOR SPL isn't required for this board, since the NOR is directly
memory mapped.
Allow to overwrite the env in ram while using brn variant. Do not set
the power GPIO pin twice.
Signed-off-by: Mathias Kresin <dev@kresin.me>
use:
- 00nn for u-boot patches
- 01nn for new boards
While doing the rework, the board definitions for the easy50712 and
easy80920 were moved to distinct board definitions patches.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
v3 includes changes suggested by L. D. Pinney & Karl Palsson-
Eliminate en25q64 (4MB) flash chip
Alphabetization
Remove hyphen in model
Rename profile from miwifinano.mk to xiaomi.mk
Add gpios that are attached to leds
SVN-Revision: 49024
Explicit sets the size of the mtdparts, because the kernel has also an explicit value.
If they have diffent sizes the ubi won't be detected.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49018
otherwise the uboot is missing important commands like bootz
Signed-off-by: Martin Mueller <mm@sig21.net>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49017
Since switching to new ubi(kernel,squashfs,ubifs) layout, the kernel lies in a
ubi volume. Dropping the mtd parts because the mtd layout is saved in the
device-tree, which is appended to the zImage.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49016
Add support for Xilinx ZC702 Dev board
Zynq target is using 4.4 kernel and mainline 2016.1 u-boot.
Patch is tested with Xilinx ZC702 Dev board with SD boot mode.
known issues:
- no QSPI driver in 4.4 kernel: no QSPI flash support
- USB is not working in 4.4 kernel
Signed-off-by: Jason Wu <jason.wu.misc@gmail.com>
create mode 100644 package/boot/uboot-zynq/Makefile
create mode 100644 target/linux/zynq/Makefile
create mode 100644 target/linux/zynq/base-files.mk
create mode 100755 target/linux/zynq/base-files/etc/board.d/02_network
create mode 100644 target/linux/zynq/base-files/etc/config/network
create mode 100644 target/linux/zynq/base-files/etc/inittab
create mode 100644 target/linux/zynq/config-4.4
create mode 100644 target/linux/zynq/image/Makefile
create mode 100755 target/linux/zynq/image/mkits.sh
create mode 100644 target/linux/zynq/patches-4.4/0001-arm-dts-zynq-zc702.dts-Set-default-rdinit-to-sbin-in.patch
create mode 100644 target/linux/zynq/profiles/zc702.mk
SVN-Revision: 48697
U-boot ships with the `mx6qsabresd` configuration file to configure a
bootloader suitable for booting the Freescale i.MX6q SABRE evaluation board
from SD card. Expose this option in the uboot-imx6 Makefile.
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
SVN-Revision: 48014
