Commit Graph

5 Commits

Author SHA1 Message Date
Mathew McBride
cef98caf6e layerscape: remove Traverse LS1043 boards
The Traverse LS1043 boards were not publicly released,
all the production has been going to OEM customers who
do not use the image format defined in the OpenWrt tree.

Only a few samples were circulated outside Traverse
and our OEM customers. The public release (then called
Five64) of this series was cancelled in favour of our
LS1088A based design (Ten64).

It is best to remove these boards to avoid wasting
OpenWrt project and contributor resources.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 8e7ba6fbae)
2023-07-26 13:36:58 +02:00
Mathew McBride
68a4c60b5c layerscape: armv8_64b: add Traverse Ten64 NAND variant
The Ten64 board[1] is based around NXP's Layerscape LS1088A SoC.
It is capable of booting both standard Linux distributions
from disk devices, using EFI, and booting OpenWrt
from NAND.

See the online manual for more information, including the
flash layout[2].

This patchset adds support for generating Ten64 images
for NAND boot.
For disk boot, one can use the EFI support that was
recently added to the armvirt target.

We previously supported NAND users by building
inside our armvirt/EFI target[3], but this approach
is not suitable for OpenWrt upstream. Users who
used our supplied NAND images will be able to upgrade
to this via sysupgrade.

Signed-off-by: Mathew McBride <matt@traverse.com.au>

[1] - https://www.traverse.com.au/hardware/ten64
[2] - https://ten64doc.traverse.com.au/hardware/flash/
[3] - Example:
285e4360e1
(cherry picked from commit af0546da34)
2023-07-26 13:36:58 +02:00
Wojciech Dubowik
924a5aabc7 layerscape: Add ls1028ardb support
Add support for NXP LS1028ARDB reference board. It's a dual core
Coretex-A53 board with 4G RAM and 5 Eternet ports (4 ports are
connected to MSCC Felix switch).

The original layout of NXP board has been kept but firmware
images are adapted to be more sysupgrade friendly. At the moment
NOR and SD boots are supported.

NOR flash instructions:
* make sd card with sdboot image
* boot
* write firmware image to spi flash
$ mtd write /tmp/openwrt-layerscape-armv8_64b-fsl_ls1028a-rdb-
squashfs-firmware.bin /dev/mtd0
* change jumper to NOR boot and reset

V3:
 * Added board specific network defaults for lan/wan

v2:
 * Added INA220 curent monitor, PCF2129 RTC clock and NXP
   SA56004ED temperature sensor to default packages
 * removed compat fixups for thist board

Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
2023-05-07 14:50:50 +02:00
Adrian Schmutzler
85b1f4d8ca treewide: remove execute bit and shebang from board.d files
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.

Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.

Note:

This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-06 11:30:06 +01:00
Mathew McBride
08714738d2 layerscape: add Traverse LS1043-S support
The Traverse LS1043-S board is a router board based on
NXP/Freescale's LS1043 SoC, with 4x1GBase-T, 1 SFP and 1 SFP+,
as well as miniPCIe and M.2 LTE.

Unlike the Layerscape reference boards, the LS1043-S board has
NAND flash and uses the mainline U-Boot.

This patch implements support for the LS1043-S board, as well as
the earlier LS1043-V board. It is our intention that all boards
in this family (LS1043-S and later, Five64) will boot the same binary.

Not included in this patchset are the hwmon drivers not in the kernel
(emc1704,pac1934) or the bootloader.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2018-07-30 10:53:57 +02:00