By making the kernel argv array const, the .data section can always be
omitted from the laoder binary.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The text section in the ELF loader is aligned to the maximum page size,
which defaults to 64KB. Reduce it to the actual page size to avoid wasting
flash space for this alignment.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some devices (TP-Link TL-WR1043ND v1) don't boot reliably when the
uncompressed loader is too small. This was workarounded in the loader by
adding 512KB of padding to the .data section of the loader binary.
This approach had two issues:
- The padding was only working when .data was non-empty (otherwise the
section would become NOBITS, omitting it in the binary). .data was only
empty when no CMDLINE was set, leading to further workarounds like
fe594bf90d ("ath79: fix loader-okli, lzma-loader"), and this
workaround was only effective because a missing "const" led to the kernel
argv being stored in .data instead of .rodata
- The padding was not only added to the compressed .gz loader, but also
uncompressed .bin and .elf loaders. The prevented embedding the kernel
cmdline in the loader for non-gz loader types.
To fix both issues, move the creation of the padding from the linker script
to the gzip step.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Refresh patches.
Drop patches that have been upstreamed:
target/linux/ar71xx/patches-4.9/106-01-MIPS-ath79-fix-AR724X_PLL_REG_PCIE_CONFIG-offset.patch
target/linux/generic/backport-4.9/095-v4.12-ipv6-Need-to-export-ipv6_push_frag_opts-for-tunnelin.patch
target/linux/generic/pending-4.9/180-net-phy-at803x-add-support-for-AT8032.patch
target/linux/generic/pending-4.9/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch
target/linux/generic/pending-4.9/182-net-qmi_wwan-add-BroadMobi-BM806U-2020-2033.patch
Compile & run tested: ar71xx Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This change was originally meant to go along with the ucidef_set_interface()
fixup.
Fixes: 7e664b7c2d ("base-files: fix ucidef_set_interface() protocol selection")
Fixes: 85048a9c1f ("base-files: rework _ucidef_set_interface to be more generic")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This is a rework of previously submitted patch reworking
ucidef_set_interface_raw [1]. Here, keep the idea but instead
make _ucidef_set_interface more generic and use it instead of
ucidef_set_interface_raw.
Also change the users like ucidef_set_interface_lan and others.
[1] https://patchwork.ozlabs.org/patch/844961/
Signed-off-by: Roman Yeryomin <roman@advem.lv>
PISEN TS-D084 is an wireless router with a battery and integrated power supply based on Atheros AR9331.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz (AR9331)
- 1x USB 2.0
Flash instruction:
The manufacturer are using exactly the same firmware header as TP-LINK TL-WR703N (including device ID!). Simply upload the factory firmware into WebUI and flashing is done.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Using a version number of 16 character causes a buffer overflow in the
version number overwriting the first bit of the signature in the
mkdapimg2 tool.
I am not sure if the version number should be null terminated or not.
This patch reduces the size of the version number by removing the number
of private commits from it.
This was the original version number which caused problems:
OpenWrt-r6727+10
Now it uses this version number:
OpenWrt-r6727
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Wifi button for WNDR3700 dual band routers has been renamed to "rfkill"
and its emitted keycode changed to KEY_RFKILL. This allows OpenWrt/LEDE
to support it 'out of the box' without additional tweaking.
Until this patch, button had been sending BTN_2 keycode which was
ignored by default (no action script present). To get expected behaviour
of switching radios on and off, user had to manually rename/link
'rfkill' script to name 'BTN_2' in /etc/rc.button directory.
This patch follows similar changes for other Netgear ar71xx routers,
for example WNR2000v3. It applies cleanly to both latest trunk and 17.01
branch. Tested on WNDR3700v1.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Refreshed all patches
Added new ARM64 symbol: ARM64_ERRATUM_1024718
Compile-tested on: ar71xx
Runtime-tested on: ar71xx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Fix ART offset (make it universal for 8/16 MB versions of the board) and
while at it, include also GPIO setup for h/w watchdog (EM6324QYSP5B).
Fixes: FS#1532
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.
SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM: Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi: QCA9561 b/g/n 3x3 450Mbit/s
USB: 1x USB 2.0
IN: WPS button, WiFi button
OUT: Power LED green, Internet LED green, WLAN LED green,
LAN LED green, INFO LED green, INFO LED red
UART: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (LAN + WAN)
- WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- LEDs
Not working:
- USB port
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
Kernel support already present.
Patch adds userspace for the 'iLS' suffix model of the RB2011 family.
Enables correct initial switch settings, sysupgrade, etc.
https://mikrotik.com/product/RB2011iLS-IN
Signed-off-by: Simon Paterson <simon.paterson.nz@gmail.com>
Some Ubiquiti U-boot versions, in particular the "U-Boot 1.1.4.2-s956
(Jun 10 2015 - 10:54:50)" found with AirOS 5.6, do not correctly flush the
caches for the whole kernel address range after decompressing the kernel
image, leading to hard to debug boot failures, depending on kernel version
and configuration.
As a workaround, prepend the relocate-kernels loader, which will invalidate
the caches after moving the kernel to the correct load address.
Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Previously, tplink_pharos_check_image() would accept any image with ELF
magic and only non-printable data in the support-list, as in this case the
while-read loop would not run at all. Add the new support-list offset and
ensure an image is only accepted when the model string is actually found.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some Airmax devices can establish a Gigabit link even though the MAC only
supports 10/100 MBit/s, leading to broken connectivity. Prevent this from
happening by limiting the speed to 100MBit/s.
Fixes: FS#296
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
TP-Link Archer C60 v2 is a dual-band AC1350 router, based on
Qualcomm/Atheros QCA9561 + QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction (web):
Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and use
OEM System Tools - Firmware Upgrade site.
Flash instruction (recovery):
1. Set PC to fixed IP address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and
rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~30 second to complete recovery
Flash instruction (under U-Boot, using UART):
tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
reset
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Add support for TL-WR940N v6 board. It is pretty much the same as v5
except they only left WAN LED and removed other ones.
Installation: flash factory image through WEB UI or use TFTP.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rework (again) platform support for dual-role chipidea USB controller:
- include support for QCA9531
- use correct EHCI block size
- drop ar933x_usb_setup_ctrl_config() function
- simplify code after previous "register chipidea only in device mode"
change (fa22714181)
Reworked patch was tested on devices with below QCA WiSOCs (signal/GPIO
name with required bootstrap state for USB bus 0 in device mode):
- AR9331 (GPIO13 pull-down)
- AR9342 (RGMII_TXD1/ETXD1 pull-up)
- AR9344 (GPIO20 pull-up)
- QCA9531 (GPIO13 pull-up)
- QCA9558 (GPIO13 pull-up)
The only way to select device mode for bus 0 is to change SOC bootstrap
configuration which is sampled only once, at hard reset. Likely, other
models, like QCA9556 or AR9341, should also support dual-role USB mode
but they were not tested.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This commit adds correct model detection for UniFi
AC-Mesh. Previously said device was incorrectly detected
as UniFi AC-Lite.
The Information about the device is stored at 0xC in the EEPROM
partition. It corresponds to the sysid in /etc/board.info of the
Ubiquiti stock firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
D-Link DAP-1330 rev. A1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR1)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 6x LED (2 are bi-color), 2x button
- 4 pin on pcb (looking from eth port and from left to right tx,rx,gnd,vcc)
Flash instruction: use "factory" image directly in vendor GUI.
This device has a recovery system that assign the ip addr of env
variable "serverip" via dhcp to a pc, and the "ipaddr" value to itself.
The recovery it's triggered by a not bootable firmware,
or pressing the reset button during the bootloader startup (first 30 seconds).
The recovery uses a http page to restore the firmware, and it's checking
the firmware image header, so use the "factory" image to
restore or the original firmware.
You can access vendor firmware over serial using:
- login: root
- password: linuxrocks
Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
It was wrong from the beginning and the trigger for the wan led was
never set due to the typo.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Only register the chipidea usb device if the strapping option indicates
device mode. If not, use the regular ehci platform driver.
Add qca955x device mode support, tested on 8devices Rambutan.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This bumps the 4.4. kernel in master to 4.4.119.
Includes more Meltdown & Spectre mitigation.
* Refresh patches.
* Refresh x86/config for RETPOLINE.
* Deleted 8049-PCI-layerscape-Add-fsl-ls2085a-pcie-compatible-ID.patch (accepted upstream)
* Deleted 8050-PCI-layerscape-Fix-MSG-TLP-drop-setting.patch (accepted upstream)
* Deleted 650-pppoe_header_pad.patch (does not apply anymore (code was replaced)).
Bumps from 4.4.112 to 4.4.115 were handled by Kevin Darbyshire-Bryant.
Compile-tested on: ar71xx & oxnas.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Rosen Penev <rosenp@gmail.com>
With this change, the timestamp variable is only used in ag71xx_check_dma_stuck. Small tx speedup.
Based on a Qualcomm commit. ag->timestamp = jiffies was not replaced with netif_trans_update(dev) because of this quote:
It should be noted that after this series several instances
of netif_trans_update() are useless (if they occur in
.ndo_start_xmit and driver doesn't set LLTX flag -- stack already
did an update).
From: http://lists.openwall.net/netdev/2016/05/03/87
Signed-off-by: Rosen Penev <rosenp@gmail.com>
GainStrong Oolite V5.2 is a small (39.5 x 78 mm), dual-band system on
module, based on Qualcomm QCA9531 + QCA9887. All QCA9531 SOC GPIOs are
available on castellated pins.
Specification:
- 650/400/200 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet (all ports available on castellated pins)
- 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA
- 1T1R 5 GHz (QCA9887) with ext. FEM (SKY85710-11)
- 3x U.FL
- 1x USB 2.0
The dedicated development board includes 5 FE ports, USB 2.0 port, two
buttons (one directly connected to SOC reset input), header with all
GPIOs and several LEDs.
Flash instruction:
Vendor firmware is based on OpenWrt. LuCI or sysupgrade can be used to
flash OpenWrt firmware.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
- combine support for Oolite/MiniBox V1.0 in single mach-*.c file
- fix model/board names
- include correct/full vendor name
- drop redundant package and factory image
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This adds support for AR9331 based Hak5 penetration testing tools:
- WiFi Pineapple NANO
- LAN Turtle
- Packet Squirrel
WiFi Pineapple NANO specifications:
- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: 1T1R AR9331 (built-in), 1T1R AR9271 (built-in via USB bus)
- Ethernet: 1x FE over USB (ASIX AX88772A)
- Ports: 2x RP-SMA for antennas, 1x USB 2.0 (host), 1x micro SD
- Power: USB 5 V, 1.5 A
- Other: status LED, reset button
LAN Turtle specifications:
- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: none
- Ethernet: 1x FE (AR9331), 1x FE over USB (Realtek RTL8152B)
- Ports: 1x RJ45, version dependent: micro SD or 3G SIM slot
- Power: USB 5 V, 0.5 A
- Other: status LED, reset button (inside, on PCB)
Packet Squirrel specifications:
- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: none
- Ethernet: 2x FE (AR9331)
- Ports: 2x RJ45, 1x USB 2.0
- Power: USB 5 V, 0.12 A
- Other: status LED, reset button, 4-way switch
Flash instructions for all 3 devices:
Original firmware is based on OpenWrt.
Use sysupgrade via SSH to flash.
Signed-off-by: Sebastian Kinne <contact@sebkinne.com>
[squashed commits, combined and reworked mach files, aligned board
naming with general convention, fixed minor issues, tested on real
hardware, reworded commit subject and description]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Some NBG6716 do not have ath10k calibration data in flash, only in chip
OTP. To determine if flash has a valid calibration data, the first two
bytes telling the length of the calibration data are checked against the
requested length. If the lengths match, calibration data is valid and
read from flash.
Signed-off-by: Matti Laakso <matti.laakso@outlook.com>
Vendor released new model (AP80Q) which is identical from hardware point
of view with already supported AP90Q. Include AP80Q in machine name.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
YunCore T830 is a simple N300 router with 5-port FE switch, detachable
antennas and USB 2.0 port.
Specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz (QCA9531), with ext. PA (SKY65174-21) and LNA
- two external, detachable antennas (RP-SMA)
- 1x USB 2.0
- 8x LED (7 driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12 V)
- UART and JTAG headers on PCB
Flash instruction:
1. First, gain root access to the device, following below steps:
- Login into web gui (default password/IP: admin/192.168.188.253).
- Go to "Advanced" -> "Management" -> "System" and download backup of
configuration (bakfile.bin).
- Open the file as tar.gz archive, edit/update "shadow" file and change
hash of root password to something known.
- Repack the archive, rename it back to "bakfile.bin" and use to
restore configuration of the device.
- After that, device will reboot and can be accessed over SSH.
2. Then, install OpenWrt:
- Login over SSH and issue command:
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
- Upload "sysupgrade" image and install it (only if previous command
succeeded) with command: "sysupgrade -n -F openwrt-...".
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Samsung WAM250 is a dual-band (selectable, not simultaneous) wireless
hub, dedicated for Samsung Shape Wireless Audio System. The device is
based on Atheros AR9344. FCC ID: A3LWAM250.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet
- 2T2R 2.4/5 GHz (AR9344), with ext. PA (SE2598L, SE5003L) and LNA
- 1x USB 2.0
- 4x LED (all are driven by GPIO)
- 2x button (reset, wps/speaker add)
- DC jack for main power input (14 V)
- UART header on PCB (J4, RX: 3, TX: 5)
Flash instruction:
This device uses dual-image (switched between upgrades) with a common
jffs2 config partition. Fortunately, there is a way to disable this mode
so that more flash space can be used by OpenWrt image.
You can easily access this device over telnet, using root/root
credentials (the same also work for serial console access).
1. Make sure that your device uses second (bootpart=2) image using
command: "fw_printenv bootpart".
2. If your device uses first image (bootpart=1), perform upgrade to the
latest vendor firmware (after the update, device should boot from
second partition) using web gui (default login: admin/1234567890).
3. Rename "sysupgrade" image to "firmware.bin", download it (you can use
wget, tftp or ftpget) to "/tmp" and issue below commands:
mtd_debug erase /dev/mtd3 0 $(wc -c /tmp/firmware.bin | awk -F' ' '{print $1}')
mtd_debug write /dev/mtd3 0 $(wc -c /tmp/firmware.bin)
fw_setenv bootpart
fw_setenv bootcmd "bootm 0x9f070000"
reboot
Revert to vendor firmware instruction:
1. Download vendor firmware to "/tmp" device and issue below commands:
fw_setenv bootpart 1
sysupgrade -n -F SS_BHUB_v2.2.05.bin
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
COMFAST CF-E385AC is an AC2200 ceiling mount AP with PoE support, based
on Qualcomm/Atheros QCA9558 + QCA9984 + QCA8337N.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 256 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet, with PoE support
- 3T3R 2.4 GHz (QCA9558), with external LNA and PA (SE2576L)
- 4T4R 5 GHz (QCA9984), with external FEM (SKY85728-11)
- 7x internal antennas
- 1x RGB LED (driven by GPIO)
- 1x button (reset)
- UART, LEDs/GPIO and USB headers on PCB
- external watchdog (Pericon Technology PT7A7514)
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
There are now supported two versions of the CF-E355AC board which differ
in 802.11ac radio chip. Include version number in board, model, image
filename, etc., also for the v1.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
COMFAST CF-E355AC v2 is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9531 + QCA9886.
Short specification:
- 2x 10/100 Mbps Ethernet, with PoE support
- 128MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, 802.11b/g/n
- 2T2R 5 GHz, 802.11ac/n/a, WAVE 2
- built-in 4x 3 dBi antennas
- output power (max): 500 mW (27 dBm)
- 1x RGB LED, 1x button
- built-in watchdog chipset
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Ding Tengfei <dtf@comfast.cn>
[updated kernel config for both boards]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The "QCA9531 v2.0 802.11n 2x2 2.4 GHz Premium SOC for WLAN Platforms"
datasheet (80-Y7991-1 Rev. C - October 2014) doesn't specify support for a
40 Mhz reference clock. The register description for "Bootstrap Options"
(page 31) defines following states for the bit 4 (REF_CLK):
* 0 - CLK25 (default)
* 1 - (reserved)
Devices like the TP-Link CPE210 v2 has this bit set to 1 but is using a 25
Mhz reference clock. OpenWrt is still interpreted this bit as 40 Mhz and
then break the bootup of the system due to this incorrect interpretation.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[refreshed patches]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
WHQX E1700AC v2 is based on Qualcomm QCA9563 + QCA9880 + QCA8334.
Specification:
- 750/400/250 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz (QCA9563) with external FEM (SKY85309-11)
- 3T3R 5 GHz (QCA9880) with external FEM (SKY85728-11)
- 2x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 1x USB 2.0
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (J5) and LEDs (J13) headers on PCB
WHQX E600G is based on Qualcomm QCA9531.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9531) with external PA (LXK-6601)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J100), SIM (J34), JTAG (J5) and LEDs (J7) headers on PCB
WHQX E600GAC is based on Qualcomm QCA9531 + QCA9887.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887) with external FEM (SKY85703-11)
- 2x 10/100 Mbps Ethernet
- 6x LED (1x RGB, 5 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-12 V)
- UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB
Important notice:
First version of these boards are using different mtd layout, with ART
data at the end. You should not use v2 images on v1 board because it
will result in lost of ART data!
Flash instruction (using U-Boot CLI and tftp server):
1. Configure PC with static IP 192.168.1.10 and tftp server.
2. Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
3. Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
4. Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
1. Configure PC with static IP 192.168.1.xxx(2-254)/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
3. Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: Peng Zhang <sd20@qxwlan.com>
[reworked: image generation code, mach-* files, commit description,
fixed minor code style issues, rebased on master]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Calling nand_do_upgrade() from platform_pre_upgrade() was deprecated
with 30f61a34b4 ("base-files: always use staged sysupgrade").
Update the platform upgrade code to use platform_do_upgrade() for NAND
images as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The watchdog kill command was meant for busybox watchdog. Busybox watchdog
was replaced by the procd watchdog mid 2013 with commit df7ce9301a
("busybox: disable the watchdog utility by default"), which makes the kill
command obsolete since quite some time.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add more registers and flags to ar71x_regs.h for QCA955x and QCA956x
SoCs. Values come from Qualcomm Atheros u-boot code.
Patches can be merged into
622-MIPS-ath79-add-more-register-defines-for-QCA956x-SoC.patch
Signed-off-by: Julien Dusser <julien.dusser@free.fr>
EG-200 is a DIN rail mountable device with one ethernet port, wifi,
an RS-485 port, and an internal USB attached uSD card reader.
Two leds, "modbus" and "etactica" are managed by userspace applications
in factory firmware.
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Karl Palsson <karlp@etactica.com>
This device is identical as TP-Link RE450
RE355 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9558+QCA9880.
Specification:
720/600/200 MHz (CPU/DDR/AHB)
64/128 MB of RAM (DDR2)
8 MB of FLASH (SPI NOR)
3T3R 2.4 GHz
3T3R 5 GHz
1x 10/100/1000 Mbps Ethernet
7x LED, 3x button
UART header on PCB
Flash instruction:
Web:
Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin
and use OEM System Tools - Firmware Upgrade site.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
COMFAST CF-E375AC is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337.
Short specification:
2x 10/100/1000 Mbps Ethernet, with PoE support
128MB of RAM (DDR2)
16 MB of FLASH
3T3R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11ac/n/a, wave 2
built-in 5x 3 dBi antennas
output power (max): 500 mW (27 dBm)
1x RGB LED, 1x button
built-in watchdog chipset
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Ding Tengfei <dtf@comfast.cn>
Qualcomm claims this improves the D-cache footprint. Origina commit message below:
From: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Date: Fri, 7 Jun 2013 10:57:28 -0500
Subject: [ag71xx] cluster/align structs for cache perf
Cluster the frequently used, per-packet structures in ag71xx near
to each other, and cacheline-align them. Some other re-ordering
occurred to move "warmer" structures near the per-packet structures.
Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This machfile also contains the code for the TL-WR842N/ND v2, which is in
ar71xx-generic and not in ar71xx-tiny.
Fixes: 0cd5e85e7a "ar71xx: create new ar71xx/tiny subtarget for 4MB flash
devices"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Add the Embedded Wireless "Balin" platform
SoC: QCA AR9344 or AR9350
RAM: DDR2-RAM 64MBytes
Flash: SPI-NOR 16MBytes
WLAN: 2 x 2 MIMO 2.4 & 5 GHz IEEE802.11 a/b/g/n
Ethernet: 3 x 10/100 Mb/s
USB: 1 x USB2.0 Host/Device bootstrap-pin at power-up
PCI-Express: 1 x lane PCIe 1.2
UART: 1 x Normal, 1 x High-Speed
JTAG: 1 x EJTAG
GPIO: 10 x Input/Output multiplexed
The module comes already with the current vanilla OpenWrt firmware.
To update, use "sysupgrade" image directly in vendor firmware.
Signed-off-by: Catrinel Catrinescu <cc@80211.de>
commit e15c63a375
ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC)
changed the existing rb-nor-flash-16M-ac image in a way that it would
now only support the rb-wapg-5hact2hnd.
The board show however rather be added to the existing boards in the
rb-nor-flash-16M image template.
Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The patch adds support for the MikroTik RB911-2Hn (911 Lite2)
and the RB911-5Hn (911 Lite5) boards:
https://mikrotik.com/product/RB911-2Hnhttps://mikrotik.com/product/RB911-5Hn
The two boards are using the same hardware design, the only difference
between the two is the supported wireless band.
Specifications:
* SoC: Atheros AR9344 (600MHz)
* RAM: 64MiB
* Storage: 16 MiB SPI NOR flash
* Ethernet: 1x100M (Passive PoE in)
* Wireless: AR9344 built-in wireless MAC, single chain
802.11b/g/n (911-2Hn) or 802.11a/g/n (911-5Hn)
Notes:
* Older versions of these boards might be equipped with a NAND
flash chip instead of the SPI NOR device. Those boards are not
supported (yet).
* The MikroTik RB911-5HnD (911 Lite5 Dual) board also uses the
same hardware. Support for that can be added later with little
effort probably.
Installation:
1. Setup a DHCP/BOOTP Server with the following parameters:
* DHCP-Option 66 (TFTP server name): pointing to a local TFTP
server within the same subnet of the DHCP range
* DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
of the to be booted image. The usable intramfs files are:
- openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
- openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
- openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin
2. Press the reset button on the board and keep that pressed.
3. Connect the board to your local network via its ethernet port.
4. Release the button after the LEDs on the board are turned off.
Now the board should load and start the initramfs image from
the TFTP server.
5. Upload the sysupgrade image to the board with scp:
$ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin
5. Log in to the running system listening on 192.168.1.1 via ssh
as root (without password):
$ ssh root@192.168.1.1
7. Flash the uploaded firmware file from the ssh session via the
sysupgrade command:
root@OpenWrt:~# sysupgrade /tmp/fw.bin
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Add patches for the leds-gpio driver to make it usable with
open-drain and open-source kind of GPIO lines.
This type of functionality is required by various MikroTik boards.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Modify the rbspi_platform_setup() function to return the pointer of the
rb_info structure. This allows board specific setup routines to access
the various fields of the information. It is useful for investigating
the hardware option bits for example.
Also update the board setup codes, to ensure that those handle the new
return value correctly.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Add bit definitions for the 'hardware options' tag which is used in
the MikroTik devices' hardware configurations. These values can be
used in board setup codes, to do different initialization sequences.
The values were obtained from the RouterOS 6.41-rc38 patches.
Additionally, introduce two helper functions what make the processing
of the hardware options easy.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The setup code of the OpenMesh OM5P ACv2 device uses nothing
from the mdio-gpio.h header, so remove the inclusion of that.
Also remove the kernel version check which is needed only
because the mdio-gpio.h header exists in a different path
in older kernels.
Compile tested only.
Cc: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Commit e15c63a375 ("ar71xx: add support for MikroTik RouterBOARD wAP
G-5HacT2HnD (wAP AC") broke the format of the patches. In unified diff
format, the unchanged, contextual lines must be preceded by a space
character.
Refresh the patches with quilt to fix them.
Fixes: e15c63a375 ("ar71xx: add support for MikroTik RouterBOARD wAPG-5HacT2HnD (wAP AC")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The patches introduced in commit 20e68f6d39 ("ar71xx: kernel: enable
PCI on QCA9556 SoC") have non standard format. In unified diff format,
the unchanged, contextual lines must be preceded by a space character.
Refresh the patches with quilt to fix them.
Fixes: 20e68f6d39 ("ar71xx: kernel: enable PCI on QCA9556 SoC")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The setup code defines four individual structures for the
Reset buttons of the supported boards. The only difference
between the definitions is the GPIO number used for the
button.
Replace the different structures with one generic variant,
and add a helper function to simplify the button registration.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Match mapping of the switch LEDs according to the TP-Link
firmware behavior. LAN port 1 triggers the most right LAN LED,
LAN port 2 the second LAN LED from the right and so on.
Signed-off-by: David Bauer <mail@david-bauer.net>
Current EnGenius ENS202EXT factory image recipe version causes factory
images of the following devices to be corrupted. This issue wasn't
visible until recent changes of image Makefile snippets order.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This patch adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP
AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with
integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet
ports.
See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9556
- RAM: 64 MB
- Storage: 16 MB NOR
- Wireless:
· Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
· Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
- Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port, passive
PoE in
Working:
- Board/system detection
- Sysupgrade
- Serial console
- Ethernet
- 2.4 GHz radio
- 5 GHz radio
- Reset button
Not working:
- LEDs (added according to Mikrotik's GPL sources but not functional)
Unsupported:
- ZT2046Q SPI temperature and voltage sensor
Contributors: Giuseppe Tipaldi (@Ciusss89)
Ricky (@rickydee)
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: whitespace fix, use PHYADDR instead of PHYMASK]
This patch enables the PCI bus on the QCA9556 SoC, the same way it is
done on the same family SoC QCA9558.
Tested on a MikroTik RouterBoard wAPG-5HacT2HnD (wAP AC).
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
GL.iNet GL-AR750 is a small size, dual-band (AC750) router, based on
Qualcomm/Atheros QCA9531 v2 + QCA9887. FCC ID: 2AFIW-AR750.
Specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 1x USB 2.0 (power controlled by GPIO)
- 1x microSD (GL857L)
- 3x LED (all driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- header for optional PoE module
- 1x micro USB for main power input
- UART + I2C header on PCB
Flash instruction:
Vendor firmware is based on OpenWrt/LEDE. GUI or sysupgrade can be used
to flash OpenWrt/LEDE firmware.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network R36A is a successor of the previous model, the R36 (Ralink
RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2.
Specification:
- 650/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB
- 1x USB 2.0 (power controlled by GPIO)
- 6x LED (5 of them are driven by GPIO)
- 2x button (reset, wifi/wps)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- DC jack for main power input (12 V)
- UART header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Teltonika RUT900 is an industrial 3G router based on Atheros AR9344.
There are available 3 other models in RUT9xx series: RUT905, RUT950 and
RUT955, which differ in availability of additional I/O ports, built-in
GSM modem type, GPS antenna and other features. FCC ID of the RUT950
model (LTE module built-in): 2AET4-RUT950.
This patch adds support for the RUT900 model only but can be easily
extended to cover whole series. Also, as there are several different
3/4G modules (Huawei, Quectel, Telit) used in whole series, packages
required for WWAN support are not included by default. It is up to the
user to install required software for built-in modem.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA
- built-in 3G module (example: Telit HE910-D)
- 2x miniSIM slot
- 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G)
- PCA9539 16-bit GPIO I2C expander
- 12x LED (4 are driven by AR9344, 7 by PCA9539)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- UART available on PCB edge connector
Serial console pinout:
- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side
Flash instruction:
Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1".
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network N5Q is a successor of previous model, the N5 (outdoor
CPE/AP, based on Atheros AR7240 + AR9280). New version is based on
Atheros AR9344.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 5 GHz (AR9344), with ext. PA (RFPA5542) and LNA, up to 27 dBm
- 8x LED (7 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmare which is based
on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network AP91-5G is a 5 GHz outdoor AP/CPE board, based on Atheros
AR7240 + AR9280.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 32 MB of RAM (DDR1)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1T1R 5 GHz (AR9280), with ext. PA (SE5004L) and LNA, up to 27 dBm
- 6x LED (5 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART and LEDs headers on PCB
Flash instruction:
Use "factory" image in vendor GUI (in case of problems, make sure your
board has up to date firmware). Alternatively, TFTP in U-Boot can be
used: select option "2. Load system code then write to Flash via TFTP"
during early boot and use "sysupgrade" image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This new subtarget sets the small_flash flag and removes unused kernel
configuration.
small_flash removes KERNEL_KALLSYMS, which saves ~107KB in the default
configuration; removing unneeded hardware support from ar71xx/tiny saves
another ~18KB (both after LZMA).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Rather than including all machines for the generic subtarget in the base
configuration, leave the base configuration without specific machines and
create a proper subtarget config for ar71xx/generic. The configuration
diffs of the mikrotik and nand subtargets get significantly shorter, as
will the configurations of future subtargets.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
While we'd like to convert ar71xx to DT-based configuration
eventually, we aren't quite there yet, and shipping half-baked DT support
that is not used at all wastes precious space.
Saves ~120KB before LZMA, ~33KB after LZMA.
Run-tested on TP-Link CPE510 and TL-WR841 v7.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The TP-Link firmware uses (primary_mac-1) as MAC-address
for the 5GHz WiFi. This applies the same behaviour to LEDE.
Currently, the MAC-address is retrieved from eth1, which
does not exist on the Archer C7 v4. As a result from this,
every C7 v4 with LEDE carries the same MAC-Address on the 5GHz WiFi.
Signed-off-by: David Bauer <mail@david-bauer.net>
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.4.0 is always
false. Remove the obsolete check from mach-rb4xx.c to clean up the code
a bit.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.2.0 is always
false. Remove the obsolete check from ag71xx_main.c to clean up the code
a bit.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 3.15.0 is always
false. Remove the obsolete checks from the target specific source files
to clean up the code a bit.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Disable the drivers for the following ethernet switches:
Realtek RTL8306
Realtek RTL8366/8367
Marvell 88E6060 (DSA)
Marvell 88E6063 (DSA)
Also disable the phy driver for Marvell PHYs.
None of the supported RouterBOARDs are using any device
which needs these drivers.
Disable the DSA framework too, because it is not required
by the remaining switch drivers.
This reduces the compressed kernel size by ~20KB.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The Marvell 88E6063 ethernet switch driver depends on the DSA
framework. Add a 'depends on NET_DSA' statement to its Kconfig
entry to state that explicitly.
Fixes the following Kconfig warning:
warning: (NET_DSA_MV88E6060 && NET_DSA_MV88E6063) selects NET_DSA_TAG_TRAILER which has unmet direct dependencies (NET && NET_DSA)
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Building Linux 4.4 for ar71xx throws the following warnings in
drivers/net/phy/mdio-bitbang.c:
CC drivers/net/phy/mdio-bitbang.o
In file included from include/linux/irqflags.h:14:0,
from drivers/net/phy/mdio-bitbang.c:20:
drivers/net/phy/mdio-bitbang.c: In function 'mdiobb_read':
include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
(void)(&__dummy == &__dummy2); \
^
include/linux/irqflags.h:63:3: note: in expansion of macro 'typecheck'
typecheck(unsigned long, flags); \
^
include/linux/irqflags.h:124:3: note: in expansion of macro 'raw_local_irq_save'
raw_local_irq_save(flags); \
^
drivers/net/phy/mdio-bitbang.c:162:2: note: in expansion of macro 'local_irq_save'
local_irq_save(flags);
^
include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
(void)(&__dummy == &__dummy2); \
^
include/linux/irqflags.h:68:3: note: in expansion of macro 'typecheck'
typecheck(unsigned long, flags); \
^
include/linux/irqflags.h:126:39: note: in expansion of macro 'raw_local_irq_restore'
#define local_irq_restore(flags) do { raw_local_irq_restore(flags); } while (0)
^
drivers/net/phy/mdio-bitbang.c:175:2: note: in expansion of macro 'local_irq_restore'
local_irq_restore(flags);
^
drivers/net/phy/mdio-bitbang.c:159:11: warning: unused variable 'i' [-Wunused-variable]
int ret, i;
^
In file included from include/linux/irqflags.h:14:0,
from drivers/net/phy/mdio-bitbang.c:20:
drivers/net/phy/mdio-bitbang.c: In function 'mdiobb_write':
include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
(void)(&__dummy == &__dummy2); \
^
include/linux/irqflags.h:63:3: note: in expansion of macro 'typecheck'
typecheck(unsigned long, flags); \
^
include/linux/irqflags.h:124:3: note: in expansion of macro 'raw_local_irq_save'
raw_local_irq_save(flags); \
^
drivers/net/phy/mdio-bitbang.c:185:2: note: in expansion of macro 'local_irq_save'
local_irq_save(flags);
^
include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
(void)(&__dummy == &__dummy2); \
^
include/linux/irqflags.h:68:3: note: in expansion of macro 'typecheck'
typecheck(unsigned long, flags); \
^
include/linux/irqflags.h:126:39: note: in expansion of macro 'raw_local_irq_restore'
#define local_irq_restore(flags) do { raw_local_irq_restore(flags); } while (0)
^
drivers/net/phy/mdio-bitbang.c:200:2: note: in expansion of macro 'local_irq_restore'
local_irq_restore(flags);
^
These are caused by the 900-mdio_bitbang_ignore_ta_value and
901-phy-mdio-bitbang-prevent-rescheduling-during-command patches.
The first patch removes some code but it does not remove the variable
which is used by the removed code only.
The second patch adds local_irq_{save,restore} calls. The type of the
argument of these calls must be 'unsigned long', but the patch defines
the variable as 'long'.
Fix both patches to silence the warnings.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Commit c312cef223 ("ar71xx: spi-rb4xx fix.") replaced the clk_enable() call
with clk_prepare_enable() to meet the common clock framework requirements.
However it did not change the clk_disable() call in the error patch which
thus leads to imbalance.
Fix the code by using the correct counterpart of clk_prepare_enable() in both
places.
Fixes: c312cef223 ("ar71xx: spi-rb4xx fix.")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
This patch adds support for the MikroTik RouterBOARD 921GS-5HPacD r2
(mANTBox 15s), an outdoor sector antenna with a built-in 802.11ac
wireless router. Additionally, it adds a new profile for devices with
>= 128 MB NAND flash and 802.11ac to the ar71xx/mikrotik subtarget.
See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9558 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9822 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in
- SFP: 1x host
Working:
- Board/system detection
- NAND storage detection
- Wireless
- Ethernet
- 1x user LED
- Reset button
- Sysupgrade
Untested:
- SFP cage (probably not working)
Installation:
- Boot initramfs image via TFTP and then flash sysupgrade image
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Apply code from commits 9e1bc27e6d
(ar71xx: Fix UBIFS work on Mikrotik RB95x devices) and
665bb27499 (ar71xx: fix invalid pointer
dereference in rb95x_nand_scan_fixup()) to RB92x devices too.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
In the stock firmware both eth0 and eth1 are set to br-lan,
add this behavior to our images.
Fixes: FS#1084
Signed-off-by: Marty E. Plummer <hanetzer@protonmail.com>
Since Linux 4.6, mtd->priv no longer points to the NAND specific
structure. Under 4.9 it contains NULL, thus using it to access
chip->options causes an invalid pointer dereference (FS#1200).
Update the code to use the mtd_to_nand() helper under 4.9 to obtain
the address of the chip specific data.
Fixes: 7bbf4117c6 ("ar71xx: Add kernel 4.9 support")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Since Linux 4.6, mtd->priv no longer points to the NAND specific
structure. Under 4.9 it contains NULL, thus using it to access
the fields of the nand_chip structure causes an invalid pointer
dereference.
Update the code to use the mtd_to_nand() helper under 4.9 to obtain
the address of the chip specific data.
Compile tested only.
Fixes: 7bbf4117c6 ("ar71xx: Add kernel 4.9 support")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
This reverts commit 256990cbc0.
this commit caused a compile error
"TL_WR1043_V5_GPIO_LED_WANORANGE" is undefined.
Signed-off-by: John Crispin <john@phrozen.org>
Add missing definitions for the orange WAN LED on the TL-WR1043N(D) v4 and
v5. Minor format correction on a constant for consistency.
Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
This patch fixes the switch port numbering on Mikrotik RB951Ui-2nD (hAP).
Also fixes the switch port numbering shown on LuCI for Mikrotik RB493G.
Signed-off-by: João Chaínho <joaochainho@gmail.com>
For an unknown reason gcc tries to link in crti.o when building with a
glibc toolchain (this does not happen with other targets). Prevent this
by telling gcc explicitly to not do that.
Fixes the following build error:
/home/jonas/git/lede/staging_dir/toolchain-mips_24kc_gcc-5.5.0_glibc/lib/gcc/mips-openwrt-linux-gnu/5.5.0/../../../../mips-openwrt-linux-gnu/lib/crti.o: In function `_init':
(.init+0x18): relocation truncated to fit: R_MIPS_GOT16 against `__gmon_start__'
/home/jonas/git/lede/staging_dir/toolchain-mips_24kc_gcc-5.5.0_glibc/lib/gcc/mips-openwrt-linux-gnu/5.5.0/../../../../mips-openwrt-linux-gnu/lib/crti.o: In function `_init':
(.init+0x28): relocation truncated to fit: R_MIPS_CALL16 against `__gmon_start__'
collect2: error: ld returned 1 exit status
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This will avoid some conflicts when doing a git rebase or merge,
specially when adding support to a new device.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
[drop brcm47xx changes which rename the images]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Recent RouterBOOT version (at least version 3.41 on RB911G-5HPacD)
use "Board=" kernel parameter instead of "board=" to pass the board
name to the kernel. Due to this change the board detection code is
not working on the devices shipped with the new RouterBOOT version.
Because the kernel is unable to identify these boards they become
unusable despite that they are supported by the current code.
Update the prom_init code to convert the 'Board' kernel parameter to
'board'. After this change, the board detection works also with the
new RouterBOOT versions.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The boardname isn't used any longer to find the subdirectory in the
sysupgrade tar archive, which makes this override useless.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Qualcomm claims this reduces cache misses. Original commit message below:
From: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Date: Tue, 11 Jun 2013 12:18:46 -0500
Subject: [ag71xx] reduce NAPI weight
In an attempt to increase our cache warmth, we are decreasing NAPI.
This increases the warmth of the reused SKBs.
Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The motivation for this was misguided. It turns out tuning the NAPI weight could be useful for testing purposes. Therefore reverting.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This commit fixes LAN Port 1 not transferring data in case no
other LAN Port has active link-state on TP-Link Archer C58/C59.
Signed-off-by: David Bauer <mail@david-bauer.net>
