Commit Graph

46285 Commits

Author SHA1 Message Date
Michal Cieslakiewicz
ad6c6361f9 ath79: enable all space on Netgear ar9344-based WNDR routers
Netgear WNDR routers (AR9344 models) like WNDR4300 have 128 MiB of flash
memory but only first 32 MiB are used now - both by vendor's firmware and
OpenWrt. This patch concatenates two regions of flash memory: ubi part
of firmware partition and reserved (unused) space beyond 'caldata_backup'
while preserving ART backup. No data is wiped or moved away.
This increases area for OS ubi volumes from 23 to 119 Megabytes.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-12-19 22:41:57 +01:00
Paul Fertser
174ff7d754 base-files: send informational UDP message each second waiting
The preinit network initialisation and failsafe informational message
are inherently racy as the interface takes some time to become
functional after "ip link set $pi_ifname up" command.

Consider this timing:

[   12.002713] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   12.008819] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
[   12.118877] random: procd: uninitialized urandom read (4 bytes read)
[   13.068614] eth1: link up (1000Mbps/Full duplex)
[   13.073309] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   13.080445] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.1: link becomes ready

Since the UDP message was sent prior to link becoming ready, it was
never seen on the wire.

The default failsafe timeout is set to 2 seconds, so with this patch
there are two attempts to send the message, one spent in vain, and the
other visible in tcpdump on an attached host. Of course, in cases when
the interface is brought up faster it leads to two messages, however it
should be harmless. This patch (almost) doesn't affect normal boot time
while still allowing to enter failsafe reliably with a single button
press, matching the official "generic failsafe" documentation.

Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-12-19 22:41:57 +01:00
Petr Štetiar
98b3526bf2 iputils: move iputils tools to packages feed
iputils has moved from the master tree to the packages feed, and is
switching from the abandoned skbuff.net upstream to
github.com/iputils/iputils.

Ref: https://git.openwrt.org/556698cedf9e86a0ffe9f148d4e8e733676c26f6
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-12-19 22:41:57 +01:00
Ansuel Smith
2a82e0e1ca ipq806x: switch to 4.19 kernel version
It has been used by several people for some time already and feedback
has been mostly positive.

Ref: https://github.com/openwrt/openwrt/pull/2472
Tested-by: Hannu Nyman <hannu.nyman@iki.fi> [ipq8065, R7800]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065, NBG6817]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[separate commit, commit subject and description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-12-19 22:41:57 +01:00
Ansuel Smith
ce8707ea79 ipq806x: update USB3 modules for 4.19
- Use new dwc3-qcom usb driver.
- Drop dwc3-of-simple as we have a dedicated driver now.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[split into separate commit, commit subject facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-12-19 22:41:57 +01:00
Pavel Kubelun
77e7d6c20d ipq806x: add missing core1 voltage tolerance
Voltage tolerance is accounted per core, not per cpu, so add
missing DT entry.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2019-12-19 22:41:57 +01:00
Ansuel Smith
1698b36bb4 kernel: make dwc3 usb driver depends on kernel 4.14
- usb-dwc3-of-simple is not used anymore as we have qcom dedicated driver
- usb-phy-qcom-dwc3 is not dependent of dwc3-of-simple

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2019-12-19 22:41:57 +01:00
Ansuel Smith
402153623d ipq806x: fix tsens driver in 4.19
Added patch:

 - 063-3 Fix tsense shared memory problem

Recent changes in ioremap_resource function are causing fails for the
memory areas which are already mapped. This changes are causing tsense
driver failures during initialization:

  qcom-tsens 900000.thermal-sensor: tsens init failed

So this patch uses simple ioremap in order to use this shared memory
space.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[commit subject and desciption facelitf]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-12-19 22:41:57 +01:00
Christian Lamparter
f28e6ae7ce ipq806x: improve mdio gpios list
Improve rediability of gpio mdio list. No functional change.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-12-19 22:41:57 +01:00
Christian Lamparter
2296d41a1c ipq806x: ap161: fix wrong definition stdout
From documentation
https://www.kernel.org/doc/Documentation/devicetree/bindings/chosen.txt
should be just stdout-path

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-12-19 22:41:57 +01:00
Christian Lamparter
044c79689b ipq806x: ap148: reorganize dts
Reorganize dts to use tags from ipq8064 dtsi

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2019-12-19 22:41:57 +01:00
Christian Lamparter
fe26364065 ipq806x: d7800: fix warning on dtc compilation
There is warning with "property has invalid length (4 bytes)"
related to nand definition. Set size-cells to zero to fix this.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2019-12-19 22:41:57 +01:00
Christian Lamparter
1acc054341 ipq806x: r7800: add missing wifi definition for pcie
Add missing wifi compatible definition for r7800 device.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2019-12-19 22:41:57 +01:00
Christian Lamparter
2da033eaa6 ipq806x: use ipq8064 dedicated watchdog
Add missing watchdog to list of compatible timers

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2019-12-19 22:41:57 +01:00
Christian Lamparter
df35293000 ipq806x: add nand and sata tags
Add some tags for nand and sata structure to easily
reference them in other dts.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2019-12-19 22:41:57 +01:00
Christian Lamparter
5ce72009ac ipq806x: increase drive-strength for pinmux
Increase drive-strength from
https://lore.kernel.org/patchwork/patch/626885/

2mA drive strength is not enough when we connect multiple i2c devices
on the bus with different pull up resistors.

This issue was detected when multiple i2c devices
connected on the other side of level shifters on Linaro sensor board.
Maxing up to 16mA made i2c much stable.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2019-12-19 22:41:57 +01:00
Christian Lamparter
9e7a8beb9c ipq806x: add missing gpio and gsbi declaration
Adds missing gpio and gsbi declaration.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2019-12-19 22:41:57 +01:00
Ansuel Smith
2336c2dbb1 ipq806x: disable spc on ipq8065 soc
Spc is disabled in ipq8065 board as it does cause cpu lockup
(probably caused by wrong register being set)

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2019-12-19 22:41:57 +01:00
Ansuel Smith
71b1062230 ipq806x: set apq8064 regulator to support cpuidle
Set qcom,apq8064-saw2-v1.1-cpu as regulator to make cpuidle work.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2019-12-19 22:41:57 +01:00
Christian Lamparter
61505922dc ipq806x: convert ipq8064 dtsi interrupts
Convert hardcoded interrupts value to types defined in gci include file.
Interrupts sets to 0 are converted to IRQ_TYPE_LEVEL_HIGH to fix
kernel warning. Same fix has been applied to arm64 dts.

https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1797143
https://patchwork.kernel.org/patch/10367453/
https://patchwork.kernel.org/patch/10315315/

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2019-12-19 22:41:57 +01:00
Christian Lamparter
afcb78f103 ipq806x: use new usb3 implementation
Use new usb3 implementation and refresh dts to the new dwc3 structure

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-12-19 22:41:57 +01:00
Christian Lamparter
96a509eeeb ipq806x: fix missing compatible and rename
- ipq8064 compatible was missing from nbg6817.
- Rename ap148 with a better descriptive name.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-12-19 22:41:57 +01:00
Christian Lamparter
9e9fe2392e ipq806x: convert ok to okay in dts
DT spec require okay instead of ok in dts files

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2019-12-19 22:41:57 +01:00
Christian Lamparter
63066d3006 ipq806x: refresh 4.19 patches
Reworked:

 - 0034 patchset update

Added:

 - 080 Add support for pinctrl-msm framework

Removed:

 - 0074-ipq806x-usb-Control-USB-master-reset.patch
   (we now have a dedicated driver for qcom usb)

 - 0047-mtd-nand-Create-a-BBT-flag-to-access-bad-block-marke
   (merged upstream)

 - 310-msm-adhoc-bus-support
   (it looks like it was never actually used in any dts)

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[commit subject and description facelift, SoB fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-12-19 22:41:57 +01:00
Ansuel Smith
53801ae1c7 kernel: generic: add missing config symbol to 4.19
PCI_V3_SEMI config symbol was found missing in generic kernel config
after ipq806x config refresh to 4.19.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[commit subject and description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-12-19 22:41:57 +01:00
Ansuel Smith
f81e148eb6 ipq806x: update 4.19 kernel config
These changes are needed in order to migrate old kernel 4.14 config to
the upcoming kernel version 4.19.  Also add missing configuration
options that comes up with this SoC.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[line wrap long commit description, add 4.19 to subject, soc->SoC]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-12-19 22:41:57 +01:00
Ansuel Smith
c5d2f3c476 ipq806x: copy files from 4.14 to 4.19
This copies files from files-4.14 to files-4.19 directory in order to
get clear diffs for any changes done from now on.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[added missing commit description, refreshed ea8500 and wpq864 DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-12-19 22:41:57 +01:00
Lech Perczak
b1e8a390ea ath79: restore gpio-export on TL-WDR3600/4300
This partially reverts commit 32144ba275.

This commit replaced gpio-exports in favor of gpio-hogs for enabling USB
power at boot, but this rids the user of control of the USB port power
present on this device for a long time. It was agreed on a mailing list
[1] that this is not the way to go, and this patch breaks a very common
use-case of WWAN modem reset by power cycle, used on a lot USB equipped
routers, hence revert this change until a better solution can be found.

[1] http://lists.infradead.org/pipermail/openwrt-devel/2019-November/020151.html

Tested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[adjusted commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-19 15:40:49 +01:00
Lech Perczak
60de1fdbb4 ath79: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
  resitors are missing on TX/RX lines)
- 1x micro USB (for power only)

Flash instructions:

Use "factory" image under vendor GUI.

Recovery instructions:

This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
   to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
   and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.

MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label

Root access over serial line in vendor firmware: root/sohoadmin.

Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-19 15:40:40 +01:00
Maxim Anisimov
ebf535a6cf ramips: fix portmap for TP-Link Archer C50 v4
According to 02_network portmap is wan=0 lan1=1 lan2=2 lan3=3 lan4=4

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2019-12-19 15:40:33 +01:00
Rafał Miłecki
17e2246eca mac80211: brcm: add support for BCM4359 SDIO chipset
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-12-19 09:17:22 +01:00
Rafał Miłecki
c3aa33bf70 mac80211: brcm: backport 5.5 and 5.6 kernel patches
This update doesn't include:
3b1e0a7bdfee brcmfmac: add support for SAE authentication offload
be898fed355e brcmfmac: send port authorized event for FT-802.1X
due to nl80211 dependencies.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-12-19 08:41:34 +01:00
Álvaro Fernández Rojas
922b538cc9 brcm2708: switch to cypress-nvram package
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-12-18 08:44:48 +01:00
Álvaro Fernández Rojas
859fac2b93 cypress-nvram: add new package
This package contains nvram files for brcmfmac, a mac80211 driver for FullMAC
Cypress devices.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-12-18 08:44:48 +01:00
Kevin Darbyshire-Bryant
ca7ed1712e wireguard: bump to 0.0.20191212
1ec6ece version: bump snapshot
e13de91 main: remove unused include <linux/version.h>
72eb17c wg-quick: linux: support older nft(8)
1d8e978 global: fix up spelling
e02713e wg-quick: linux: add support for nft and prefer it
b4e3a83 compat: support building for RHEL-8.1 instead of RHEL-8.0
f29e3ac socket: convert to ipv6_dst_lookup_flow for 5.5

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2019-12-17 19:46:41 +00:00
Álvaro Fernández Rojas
1115c9aad3 brcmfmac-board-rpi: remove uneeded package
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-12-17 19:20:02 +01:00
Álvaro Fernández Rojas
efe15993d3 brcm2708: switch to cypress-firmware package
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-12-17 19:20:02 +01:00
Álvaro Fernández Rojas
e332453857 cypress-firmware: add new package
This package contains firmwares provided by Cypress
See https://community.cypress.com/community/linux

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-12-17 19:20:02 +01:00
Imran Khan
27d69d2561 uboot-envtools: check for config prior to append
In the rare event a pre-populated fw_env.config exists in the rootfs prior
to firstboot, calling fw_setenv after the system has initialised will
annihilate the devices environment due to two identical lines in
fw_env.config.

Check for existence prior to blind appendage.

Signed-off-by: Imran Khan <gururug@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: fixed patch format, improved grep, cosmetics]
2019-12-17 19:35:16 +02:00
Adrian Schmutzler
f45a16dead ramips: allow to set switchdev by board in ramips_set_preinit_iface
This adds the option to determine switchdev by board when setting
preinit iface for failsafe. The patch reorganizes the code to use
functions for setting correct switchdev based on SOC and board,
which is supposed to improve readability and maintainability.

In this patch, the ramips_switchdev_from_board function is added
without specifying an actual device using it. This is meant to
make the life of device supporters waiting for merge easier, as
there is less to rebase and keep track of.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-17 15:09:48 +01:00
Sungbo Eo
38bdfcdb87 ramips: add support for ipTIME A104ns
ipTIME A104ns is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610EN
- Ethernet: 5x 10/100Mbps
  - Switch: SoC internal
- USB: 1x 2.0
- UART:
  - J2: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

In contrast to to-be-supported A1004ns, the A104ns has no usable
value in 0x1fc40 (uboot), so wan_mac needs to be calculated.
Also note that GPIOs for the LEDs really are inverted compared to
the A1004ns.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[moved state_default to device DTS, reordered properties in wmac,
added comment about wan_mac and LED GPIOs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-17 13:36:11 +01:00
Sungbo Eo
01d39cd18c ath79: migrate LED paths of TL-WDR4300 board
TL-WDR4300 board uses only green LED names in DTSI.
This patch adds migration for them.

The actual LED colors on the devices have been reported to vary
across subrevisions (v1.x). Despite, the USB LEDs on the back might
have different color than the other LEDs on the front.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-17 13:35:24 +01:00
Adrian Schmutzler
2708d58c1d ramips: add label MAC address for Edimax RG21S
The Edimax RG21S has a label which bears two MAC addresses:
2.4 GHz (n) and 5 GHz (n+1)

The complete MAC address setup is as follows:
2.4 GHz  *:83  factory 0x4, u-boot-env wlanaddr
5 GHz    *:84  factory 0x8004
LAN      *:83  u-boot-env ethaddr
WAN      *:85  u-boot-env wanaddr

Since 2.4 GHz is the first address on the label and the same
as used for ethernet, take this one for label MAC address.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-17 13:33:58 +01:00
Birger Koblitz
c79df949ab ramips: increase SPI frequency for Edimax RG21S
This increases SPI frequency from the relatively low 10 MHz to 40 MHz.

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[added commit title/message, split patch]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-17 13:33:27 +01:00
Birger Koblitz
8007853f79 ramips: remove unnecessary nodes in DTS for Edimax RG21S
This sdhci and i2c nodes were copy-pasted, but are not needed as
the device does not provide that functionality. Remove them.

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[added commit title/message, split patch]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-17 13:32:57 +01:00
Jo-Philipp Wich
762aac50c0 rpcd: update to latest Git HEAD
aaa0836 file: extend exec acl checks to commands with arguments

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-12-17 08:33:33 +01:00
David Bauer
9e1e432469 ar71xx: indicate upgrade using system LED
This enables the system LED to indicate a running firmware upgrade. This
pattern is used on most platforms provided by the generic base-files
package. ar71xx uses it's own implementation for the system-LED, where
the upgrade case is not yet implemented.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-12-16 00:51:01 +01:00
David Bauer
6ec288a178 mac80211: fix txpower when using DFS channels
With this patch, txpower for the PHY is applied when configuring the PHY
instead of the VIF. Otherwise, the configured txpower is not applied for
the first initialized VIF when using DFS channels, as it is currently
applied too early when the CAC hasn't finished.

Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
2019-12-16 00:50:10 +01:00
Hans Dedecker
a15f658ed0 odhcpd: update to latest git HEAD
d60f0a6 treewide: optimize syslog priority values

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2019-12-15 20:54:25 +01:00
David Bauer
16b01fb1b9 mpc85xx: add support for Enterasys WS-AP3710i
Hardware
--------

SoC:   NXP P1020 (2x e500 @ 800MHz)
RAM:   256M DDR3 (Micron)
FLASH: 32M NOR (Spansion S29GL128S)
BTN:   1x Reset
WiFi:  1x Atheros AR9590 2.4 bgn 3x3
       2x Atheros AR9590 5.0 an 3x3
ETH:   1x Gigabit Ethernet (Atheros AR8033)
LED:   System (green/red) - Radio{0,1} (green)
       LAN (connected to PHY)
        - GE blue
        - FE green

Serial is a Cisco-compatible RJ45 next to the ethernet port.
115200-N-8 are the settings for OS and U-Boot.

Installation
------------

1. Grab the OpenWrt initramfs, rename it to 01C8A8C0.img. Place it in
   the root directory of a TFTP server and serve it at
   192.168.200.200/24.

2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot
   by pressing Enter when prompted. Credentials are identical to the one
   in the APs interface. By default it is admin / new2day.

3. Set the bootcmd so the AP can boot OpenWrt by executing

   $ setenv boot_openwrt "setenv bootargs;
     cp.b 0xee000000 0x1000000 0x1000000; bootm 0x1000000"
   $ setenv bootcmd "run boot_openwrt"
   $ saveenv

   If you plan on going back to the vendor firmware - the bootcmd for it
   is stored in the boot_flash variable.

4. Load the initramfs image to RAM and boot by executing

   $ tftpboot 0x1000000 192.168.200.200:01C8A8C0.img; bootm

5. Make a backup of the "firmware" partition if you ever wish to go back
   to the vendor firmware.

6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp
   folder.

7. Flash OpenWrt using sysupgrade.

   $ sysupgrade -n /tmp/openwrt-sysupgrade.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-12-13 22:40:19 +01:00