Commit Graph

2 Commits

Author SHA1 Message Date
Daniel Golle
7c459ac1d5 mac80211: rt2x00: experimental improvements for MT7620 wifi
Serge Vasilugin reports:

To improve mt7620 built-in wifi performance some changes:
1. Correct BW20/BW40 switching (see comments with mark (1))
2. Correct TX_SW_CFG1 MAC reg from v3 of vendor driver see
	https://gitlab.com/dm38/padavan-ng/-/blob/master/trunk/proprietary/rt_wifi/rtpci/3.0.X.X/mt76x2/chips/rt6352.c#L531
3. Set bbp66 for all chains.
4. US_CYC_CNT init based on Programming guide, default value was 33 (pci),
   set chipset bus clock with fallback to cpu clock/3.
5. Don't overwrite default values for mt7620.
6. Correct some typos.
7. Add support for external LNA:
    a) RF and BBP regs never be corrected for this mode
    b) eLNA is driven the same way as ePA with mt7620's pin PA
	but vendor driver explicitly pin PA to gpio mode (for forrect calibration?)
	so I'm not sure that request for pa_pin in dts-file will be enough

First 5 changes (really 2) improve performance for boards w/o eLNA/ePA.
Changes 7 add support for eLNA

Configuration w/o eLAN/ePA and with eLNA show results
tx/rx (from router point of view) for each stream:
 35-40/30-35 Mbps for HT20
 65-70/60-65 Mbps for HT40

Yes. Max results for 2T2R client is 140-145/135-140
with peaks 160/150, It correspond to mediatek driver results.
Boards with ePA untested.

Reported-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[directly include v3 of the patchset submitted upstream]
(cherry picked from commit 31a6605de0)
(cherry picked from commit e785ca05e9)
(cherry picked from commit 412fcf3d44)
2022-09-19 02:48:26 +01:00
Shiji Yang
80e70be0ab ramips: add new flash layout support to Phicomm K2
Descriptions:
Phicomm K2 (PSG1218) got a new "permanent_config" partition after
update firmware to v22.5. This partition located in front of the
firmware partition, same as The Phicomm K2P and K2G. Due to this
change the new bootloader can't load previous firmware any more.
This commit is aimed at add support for Phicomm K2 which official
firmware version is 22.5.x or newer. For which runs old firmware
version, just update OpenWrt that has a prefix of "k2-v22.4".
For uniform naming, this commit also changed the model name
PSG1218 to a more recognizable name K2, refer to Phicomm K2G,
K2P K2T.

OpenWrt selection table:
official firmware version           OpenWrt
v22.4.x.x or older              phicomm_k2-v22.4
v22.5.x.x or newer              phicomm_k2-v22.5

Installation:
Same as Phicomm K2G, K2P, PSG1208.
a. TFTP + U-Boot
b. Open telnet by some web page vulnerability (Search Baidu by key
   words "K2 telnet"), and then we can upload firmware image to
   /tmp and write it to firmware partition with mtd instruction.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[rebase, add/harmonize version in model variables, fix version typo
 in commit message, wrap commit message properly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-24 20:26:00 +02:00