With some debug in qmi.sh using following patch, some errors are visible
in the registration step
@@ -29,6 +29,7 @@ proto_qmi_init_config() {
}
proto_qmi_setup() {
+ set -x
local interface="$1"
local dataformat connstat plmn_mode mcc mnc
local device apn auth username password pincode delay modes pdptype
@@ -224,6 +225,8 @@ proto_qmi_setup() {
fi
done
+ registration=$(uqmi -s -d "$device" --get-serving-system)
+
[ -n "$modes" ] && uqmi -s -d "$device" --set-network-modes "$modes" > /dev/null 2>&1
echo "Starting network $interface"
During the boot of the system, modem could not start automatically its
network registration.
netifd: wan (9235): + echo 'Waiting for network registration'
netifd: wan (9235): Waiting for network registration
netifd: wan (9235): + local 'registration_timeout=0'
netifd: wan (9235): + uqmi -s -d /dev/cdc-wdm1 --get-serving-system
netifd: wan (9235): + grep '"searching"'
netifd: wan (9235): + uqmi -s -d /dev/cdc-wdm1 --get-serving-system
netifd: wan (9235): + registration='{"registration":"not_registered","plmn_mcc":208,"plmn_mnc":20,"plmn_description":"","roaming":true}'
netifd: wan (9235): + '[' -n ]
netifd: wan (9235): + echo 'Starting network wan'
As the while loop checks only "searching" pattern, uqmi.sh script quits
searching loop and continues whereas the modem is not registered
Other issue, after X seconds modem stops searching.
netifd: wan (9213): + uqmi -s -d /dev/cdc-wdm0 --get-serving-system
netifd: wan (9213): + grep '"searching"'
netifd: wan (9213): + '[' -e /dev/cdc-wdm0 ]
netifd: wan (9213): + '[' 3 -lt 0 -o 0 '=' 0 ]
netifd: wan (9213): + let registration_timeout++
netifd: wan (9213): + sleep 1
netifd: wan (9213): + uqmi -s -d /dev/cdc-wdm0 --get-serving-system
netifd: wan (9213): + grep '"searching"'
netifd: wan (9213): + uqmi -s -d /dev/cdc-wdm0 --get-serving-system
netifd: wan (9213): + registration='{"registration":"not_registered"}'
netifd: wan (9213): + '[' -n ]
netifd: wan (9213): + echo 'Starting network wan'
netifd: wan (9213): Starting network wan
If registration_timeout is not expired, registration can be restarted
Signed-off-by: Thomas Richard <thomas.richard@kontron.com>
Tested-by: Florian Eckert <fe@dev.tdt.de>
(cherry picked from commit 2eda042d55)
OpenWRT requires a number of Perl modules to be installed. It wasn't checking on all of them.
This patch adds checks for Perl FindBin, File::Copy, File::Compare and Thread::Queue modules.
Failing to install these, will have the build break at some point. By adding these to the
prereq-build.mk script, they are checked on forehand.
Tested on a Fedora 33 and 34 (beta) that was freshly installed. Fedora appears to
break up Perl modules into small packages that need to be installed for the build to succeed.
Signed-off-by: Bas Mevissen <abuse@basmevissen.nl>
(cherry picked from commit f68c9474ac)
The stock firmware does not accept firmware with "Talon" in the name.
Tested on firmware version 1.0.10 Build 20160902 rel. 57400 which came
preinstalled, as well as latest firmware version 2.0.1 Build 20170103
rel.71053 flashed from
AD7200v1-up-ver2-0-1-P1[20170103-rel71053]_2017-01-04_10.08.28.bin.
Fixes: 1a775a4fd0 ("ipq806x: add support for TP-Link Talon AD7200")
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
[added details about vendor firmware]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit dfef88b6ca)
Fixes issue with merged DNS requests in 2.83/2.84 not being
retried on the firsts failed request causing lookup failures.
Also fixes the following security problem in dnsmasq:
* CVE-2021-3448:
If specifiying the source address or interface to be used
when contacting upstream name servers such as:
server=8.8.8.8@1.2.3.4, server=8.8.8.8@1.2.3.4#66 and
server=8.8.8.8@eth0 then all would use the same socket
bound to the explicitly configured port. Now only
server=8.8.8.8@1.2.3.4#66 will use the explicitly
configured port and the others random source ports.
Remove upstreamed patches and update remaining patch.
Signed-off-by: Alan Swanson <reiver@improbability.net>
[refreshed old runtime support patch]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 3980daffa4)
This package depends on the lantiq target and is only build for that
target. A normal package would be build by the SDK builder probably
under a different target and then this package will not be selected.
Mark it as nonshared to build it when the lantiq target gets build.
Fixes: FS#3773, FS#3774
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 454d514f46)
The removed patches were applied upstream and are not needed anymore.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 17ac9849d3)
This backports a fix for the low priority CVE-2021-28831:
decompress_gunzip.c in BusyBox through 1.32.1 mishandles the error bit
on the huft_build result pointer, with a resultant invalid free or
segmentation fault, via malformed gzip data.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 13397b2b95)
This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD),
an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet
port.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 256 MB
- Storage: 16 MB NOR
- Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae
- Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in
- 1x Ethernet LED (green)
- 7x user-controllable LEDs
· 1x power (blue)
· 1x user (green)
· 5x rssi (green)
Note:
Serial UART is probably available on the board, but it has not been
tested.
Flashing:
Boot via TFTP the initramfs image. Then, upload a sysupgrade image
via SSH and flash it normally. More info at the "Common procedures
for MikroTik products" page https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
(cherry picked from commit d1f1e5269e)
[Compile and Run Tested]
Signed-off-by: Nick Hainke <vincent@systemli.org>
This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC
(hAP ac²), a indoor dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional antennae, USB port and five
10/100/1000 Mbps Ethernet ports.
See https://mikrotik.com/product/hap_ac2 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 128 MB
- Storage: 16 MB NOR
- Wireless:
· Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
· Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in
- 1x USB Type A port
Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit faea7becaf)
[Compile Tested]
Signed-off-by: Nick Hainke <vincent@systemli.org>
The mode on the SGMII SerDes on the QCA9563 is 1000 Base-X by default.
This only allows for 1000 Mbit/s links, however when used with an SGMII
PHY in 100 Mbit/s link mode, the link remains dead.
This strictly has nothing to do with the SerDes calibration, however it
is done at the same point in the QCA reference U-Boot which is the
blueprint for everything happening here. As the current state is more or
less a hack, this should be fine.
This fixes the issues outlined above on a TP-Link EAP-225 Outdoor.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Tested-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit fbbad9a9a6)
Before: Kernel reported "usb_vbus: disabling" and the USB was not
providing power
After: USB power is switched on, peripheral is powered from the
device
Signed-off-by: Tom Stöveken <tom@naaa.de>
[squash and tidy up]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a6f7268dc7)
Removed because in upstream*
mvebu/patches-5.4/319-ARM-dts-turris-omnia-configure-LED-2--INTn-pin-as-interrupt-pin.patch
Manually rebased*
generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch
Added new backport*
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
All others updated automatically.
The new backport was included based on this[1] upstream commit that will be
mainlined soon. This change is needed because Eric Dumazet's check for
NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use
napi_gro_frags().
Compile-tested on: x86/64, armvirt/64, ath79/generic
Runtime-tested on: x86/64, armvirt/64, ath79/generic
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since support for SFP on the MikroTik RouterBOARD 922UAGS-5HPacD was
added by 4387fe00cb, the MAC addresses for eth0 (Ethernet) and eth1
(SFP) were swapped. This patch fixes the 02_network script to assign MAC
addresses correctly, so they match the label and the vendor's OS.
Tested on a RouterBOARD 922UAGS-5HPacD board.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
(cherry picked from commit 14a95b36b1)
This patch enables the SFP cage on the MikroTik RouterBOARD 922UAGS-5HPacD.
GPIO16 (tx-disable-gpios) should be governed by the SFP driver to enable
or disable transmission, but no change is observed. Therefore, it is
left as output high to ensure the SFP module is forced to transmit.
Tested on a RouterBOARD 922UAGS-5HPacD board, with a CISCO GLC-LH-SMD
1310nm module and an unbranded GLC-T RJ45 Gigabit module. PC=>router
iperf3 tests deliver 440/300 Mbps up/down, both via regular eth0 port
or SFP port with RJ45 module. Bridge between eth0 and eth1 delivers
950 Mbps symmetric.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
(cherry picked from commit 4387fe00cb)
Missing braces in a macro were leading to badly working rates sometimes
getting a success probabilty of 1.0
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 12cb52bd06)
It's in backports-5.4, but it wasn't ever merged. Upstream followed another
approach, with flow offloading, which has much better performance. Drop this
obsolete patch and refresh the kernel patches.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 17576b1b2a)
With the old ubus dsl API, the numbers for the individual line_states and
power_states were also returned. These were not ported to the new DSL
C-API. This commit adds the missing information.
For this the internal values are mapped to numbers.
* additional JSON output for state_num:
"state_num": <map_state_number>
Since not all values are meaningful only the following values are
implemented, this can be extended if the future.
* LSTATE_MAP_NOT_INITIALIZED
* LSTATE_MAP_EXCEPTION
* LSTATE_MAP_IDLE
* LSTATE_MAP_SILENT
* LSTATE_MAP_HANDSHAKE
* LSTATE_MAP_FULL_INIT
* LSTATE_MAP_SHOWTIME_NO_SYNC
* LSTATE_MAP_SHOWTIME_TC_SYNC
* LSTATE_MAP_RESYNC
* additinal JSON output for power_level:
"power_state_num": <map_power_satte_number>,
Since there are not so many here, all are mapped.
* PSTATE_MAP_NA,
* PSTATE_MAP_L0,
* PSTATE_MAP_L1,
* PSTATE_MAP_L2,
* PSTATE_MAP_L3,
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
v6:
Add state LSTATE_MAP_NOT_INITILIZED at the beginning of the list
Start the list LSTATE_MAP with -1
Reviewed-by: Andre Heider <a.heider@gmail.com>
(cherry picked from commit 4407d45d96)
Switch to Actual Net Data Rate (ACTNDR) for speed reporting on lantiq VDSL modems
Refer to ITU-T G.997.1 chapter 7.5.2.8
Independent whether retransmission is used or not in a given transmit direction:
- In L0 state, this parameter reports the Net Data Rate (as specified in G.992.3, G.992.5 or G.993.2) at which the bearer channel is operating.
- In L2 state, the parameter contains the Net Data Rate (as specified in G.992.3, G.992.5 or G.993.2) in the previous L0 state.
Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com>
Reviewed-by: Andre Heider <a.heider@gmail.com>
(cherry picked from commit 4f27ea7c33)
This commit adds monitoring for a couple of DSL line features that are
present in the lantiq firmware blobs.
* G.INP ON/OFF
* Trellis encoding ON/OFF
* Virtaul Noise ON/OFF
* Bitswap ON/OFF
Difference in size for ltq-vdsl-app = 1k
Difference in size for kmod-ltq-vdsl-vr9 < 1k
Reviewed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com>
(cherry picked from commit 48162e4c0c)
U-Boot uses the "bootpartition" variable stored in
"u-boot-env2" to select the active system partition. Allow
updates to enable system switching from OpenWrt.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit 11d24ffe96)
Switch the Netgear DTSI for the Realtek target from the OEM partition
naming scheme to accepted OpenWrt naming practices. A quick git grep for
'u-boot-env' e.g. in the OpenWrt tree turns up almost 500 hits whereas
grepping for 'bdinfo' (the OEM equivalent) returns a meagre 14.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
(cherry picked from commit 1601b39b61)
Otherwise, the last defined value will be set for all devices.
Fixes: c6c8d597e1 ("realtek: Add generic zyxel_gs1900 image definition")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 851dadc257)
The rtl83xx-phy driver is necessary for proper configuration of the
PHYs if U-Boot hasn't done that.
1000Base-T SFPs often contains a Marvell 88E1111 and will not work
without this driver. Include it by default to support copper SFPs.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit 07bf5aaa4c)
There is no need to define a static link or a phy for the sfp
ports. Using phy-mode and managed properties to describe the
link to the sfp phy.
We have to keep the now unconnected virtual "phys" because the
switch driver uses their "phy-is-integrated" property to figure
out which ports to enable as fibre ports.
Acked-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit e8d391bd46)
From the validate docs in include/linux/phylink.h:
When state->interface is PHY_INTERFACE_MODE_NA, phylink expects the
MAC driver to return all supported link modes.
Tested-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit 785d830e88)
This bug was the root cause for the failing sfp driver.
Acked-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit b8e473d18c)
The ZyXEL GS1900-8 is a 8 port switch without any PoE functionality or
SFP ports, but otherwise similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-8 v1.2
* SoC: Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash: Macronix MX25L12835F 16 MiB
* RAM: Nanya NT5TU128M8GE-AC 128 MiB DDR2 SDRAM
* Ethernet: 8x 10/100/1000 Mbit
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
8 ethernet port status LEDs (green, SoC controlled)
* Buttons: 1 on-off glide switch at the back (not configurable)
1 reset button at the right side, behind the air-vent
(not configurable)
1 reset button on front panel (configurable)
* Power 12V 1A barrel connector
* UART: 1 serial header (JP2) with populated standard pin connector on
the left side of the PCB, towards the back. Pins are labelled:
+ VCC (3.3V)
+ TX (really RX)
+ RX (really TX)
+ GND
the labelling is done from the usb2serial connector's point of
view, so RX/ TX are mixed up.
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
Instructions are identical to those for the GS1900-10HP and GS1900-8HP.
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-10HP is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only boot off the first partition anyway (hardcoded in the DTS). To
make sure we are manipulating the first partition, issue the following
commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-generic-zyxel_gs1900-8-squashfs-sysupgrade.bin
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e6ba970b6e)
Add a new common device definition for the Zyxel GS1900 line of
switches.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit c6c8d597e1)
Demote a number of debugging printk's to pr_debug to avoid log
nosie. Several of these functions are called as a result of
userspace activity. This can cause a lot of log noise when
userspace does periodic polling.
Most of this could probably be removed completely, but let's
keep it for now since these drivers are still in development.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit ba220ad2fd)
This adds the necessary nuts and bolts for the uboot settings for both the ZyXEL GS1900-8HP v1 and v2.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
(cherry picked from commit b5bc53813d)
If service() is called w/o parameter then the status display for services
with multiple instances is incorrect. E.g. samba4 or wpad have 2 instances.
root@OpenWrt:~# /etc/init.d/samba4 status
running
root@OpenWrt:~# /etc/init.d/wpad status
running
Before change:
/etc/init.d/samba4 enabled stopped
/etc/init.d/wpad enabled stopped
After change:
/etc/init.d/samba4 enabled running
/etc/init.d/wpad enabled running
Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
(cherry picked from commit 9318f61556)
Since KERNEL_SWAP is only enabled by default for !SMALL_FLASH targets, we need
to check if the current kernel supports swap before trying to configure
zram-swap, as opkg can't check for kernel dependencies.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
(cherry picked from commit 565dfeb128)
Without 'BUILD_DEVICES' defined, the U-Boot related package won't be
automatically selected when building for Toradex Apalis device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(cherry picked from commit 8c3383799a)
Looks like 'openat', 'pipe2' and 'ppoll' are now needed, possibly due
to changes on libraries used by umdns now using slightly different
calls.
Found using
/etc/init.d/umdns trace
now use umdns, ie. cover all ubus call etc., then
/etc/init.d/umdns stop
find list of syscalls traced in /tmp/umdns.*.json
Fixes: FS#3355 ("UMDNS: does not start on master with seccomp")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 00a85a1634)
Now that ujail supports seccomp also on Aarch64, add missing syscall
'fstat' to the list of allowed syscalls.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit d28880cdd8)
The mt7530_{r,w}32 operation over MDIO uses 3 mdiobus operations and
does not hold a lock, which causes a race condition when multiple
threads try to access a register, they may get unexpected results.
To avoid this, handle the MDIO lock manually, and use the unlocked
__mdiobus_{read,write} in the critical section.
This fixes the "Ghost VLAN" artifact[1] in MT7530/7621 when the VLAN
operation and the swconfig LED link status poll race between each other.
[1] https://forum.openwrt.org/t/mysterious-vlan-ids-on-mt7621-device/64495
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
(cherry picked from commit f99c9cd9c4)
Fix the PLL register value for 10 Mbit/s link modes on the UniFi AC Lite
/ Mesh / LR. Otherwise, 10 Mbit/s links do not transfer data.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 956407292d)
Fix the PLL register value for 10 Mbit/s link modes on TP-Link EAP
boards using a AR8033 SGMII PHY.
Otherwise, 10 Mbit/s links do not transfer data.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Tested-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit bbff6239e2)
e78ea9bd26 Update Nios II libm-test-ulps.
98bb18f52a malloc: Fix a realloc crash with heap tagging [BZ 27468]
fc4ecce85b S390: Also check vector support in memmove ifunc-selector [BZ #27511]
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
(cherry picked from commit d49f1acff1)
For some reason, one of the configure checks results in some infinite
loop and ends up spawning endless gcc processes, causing OOM. Just pass
a configure var to avoid it.
Same fix as 6e23813c1e
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit fc093c3f9c)
Reduce spi-max-frequency for Xiaomi MI Router 4AG model
Xiaomi MI Router 4AG MTD uses two flash chips (no specific on router versions when produced from factory) - GD25Q128C and W25Q128BV.
These flash chips are capable of high frequency, but due to poor board design or manufacture process.
We are seeing the following errors in the linux kernel bootup:
`spi-nor spi0.0: unrecognized JEDEC id bytes: cc 60 1c cc 60 1c
spi-nor: probe of spi0.0 failed with error -2`
This causes the partitions not to be detected
`VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6`
Then creates a bootloop and a bricked router.
The solution to limit this race condition is to reduce the frequency from 80 mhz to 50 mhz.
Signed-off-by: David Bentham <db260179@gmail.com>
(cherry picked from commit 17e690017d)
The crypto engine in Armada 370 SoCs is currently broken. It can be
checked installing the required packages for testing openssl with hw
acceleration:
opkg install openssl-util
opkg install kmod-cryptodev
opkg install libopenssl-devcrypto
After configuring /etc/ssl/openssl.cnf to let openssl use the crypto
engine for digest operations, and performing some checksums..
md5sum 10M-file.bin
openssl md5 10M-file.bin
...we can see they don't match.
There might be an alignment or size constraint issue caused by the
idle-sram area.
Use the whole crypto sram and disable the idle-sram area to fix it. Also
disable the idle support by adding the broken-idle property to prevent
accessing the disabled idle-sram.
We don't care about disabling the idle support since it is already broken
in Armada 370 causing a huge performance loss because it disables
permanently the L2 cache. This was reported in the Openwrt forum and
elsewhere by Debian users with different board models.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(cherry picked from commit 2e1ebe96c6)
The GL.iNet GL-MV1000 is booting from eMMC and the images for it are in
theory sysupgrade compatible. But the platform upgrade scripts were not
adjusted to select the mmcblock device as upgrade target. This resulted in
a failed sysupgrade because the mtd device (NOR flash) was instead tried to
be modified by the sysupgrade script.
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit 07e5e03711)
