QLCNIC_HWMON was activated when hwmon was set, but the dependency was
missing. This broke the build bot builds. Fix this by explicitly
activating HWMON support and adding a dependency.
Fixes: f88c64d28c ("kernel: netdev: add qlcnic")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This kmod is similar to macvlan with the difference being that the
endpoints have the same mac address.
It is useful on cloud where only one mac address allowed on port,
where macvlan not works but ipvlan would.
One use case is where multiple IPs and gateways assign on one net port
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD),
an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet
port.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 256 MB
- Storage: 16 MB NOR
- Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae
- Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in
- 1x Ethernet LED (green)
- 7x user-controllable LEDs
· 1x power (blue)
· 1x user (green)
· 5x rssi (green)
Note:
Serial UART is probably available on the board, but it has not been
tested.
Flashing:
Boot via TFTP the initramfs image. Then, upload a sysupgrade image
via SSH and flash it normally. More info at the "Common procedures
for MikroTik products" page https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Erase firmware ereas before writing to recovery or production partition
when updating them via the bootloader menu.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Ubiquiti Networks UniFi 6 LR access point comes with a total of
512 MB RAM provided by 2x 8-bit DDR3 SDRAM. This combination lead to
problems with the DDR calibration on boot resulting in occasional hang
on boot. Use updated calibration binary provided by MediaTek to make
boot on that device more reliable.
The binary has also been tested on the BananaPi BPi-R64 board and that
also works just fine with the new binary.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Missing braces in a macro were leading to badly working rates sometimes
getting a success probabilty of 1.0
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When running multiple instances of dnsmasq, for example one being for the lan
and another for a guest network, it might not be desirable to have the same dns names
configured in both networks
Signed-off-by: João Henriques <joaoh88@gmail.com>
9df230a Zero checksum handling (#25)
7688102 skip generating a UDP4 csum if the UDP6 csum is 0 and zero_csum_pass is set
4a9e4b1 zero csum: avoid calling the checksum adjustment function if udp csum is zero
2de14c5 add a module argument to skip checksum adjust for UDP if checksum is zero
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Update to the latest stable upstream version.
Drop unneeded make variables to remove redundant assignments seen during
invocation of package Makefile.
Also remove the following patch now included upstream:
* 200-fix-install-param-order-on-macos.patch
Compile and run-tested on malta/mips32be, using bpftool directly and also
libbpf (linked with tc) to inspect and load simple eBPF programs.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Rename feature variable clang-bpf-global-var following upstream changes.
This restores the HAVE_CLANG feature override and should avoid rare build
errors where a recent host clang and BTF-enabled host kernel are present.
Fixes: 23be333401 ("bpftools: update to 5.10.10")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Skip building Makefile targets that aren't packaged: tipc, dcb, ifstat,
rtacct, lnstat, and man. Also, only compile targets needed for the current
build variant i.e. don't compile 'tc' when building an 'ip' variant and
vice versa.
These changes reduce typical build times by over 30%:
$ make package/iproute2/clean && time make -j8 package/iproute2/compile
(old)
...
real 2m24.985s
user 3m12.537s
sys 0m26.677s
(new)
...
real 1m36.945s
user 2m8.734s
sys 0m20.046s
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Update the uboot-rockchip to the latest upstream release.
Remove upstreamed patches.
Tested-on: FriendlyElec NanoPi R2S
Signed-off-by: David Bauer <mail@david-bauer.net>
Select kmod-backlight as dependency for kmod-drm in case kmod-backlight
is compiled.
This fixes kernel 5.10 build issues on x86-geode with all kmods
enabled:
Package kmod-drm is missing dependencies for the following libraries:
backlight.ko
Signed-off-by: David Bauer <mail@david-bauer.net>
CONFIG_MDIO_OF depends on CONFIG_OF which is not enabled for x86.
Fixes builds of x86 with Kernel 5.10 due to unresolved dependencies.
Signed-off-by: David Bauer <mail@david-bauer.net>
The Buffalo Linkstation LS421DE NAS lacks an uboot env config file.
Create it via scripts.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
As the name suggests, act_gact has the generic actions such as dropping
and accepting packets, so move it into kmod-sched-core.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Add firmware and board file for Qualcomm Atheros QCA9377 802.11ac Wireless
Network Adapter (rev 31) recognized as [168c:0042].
This card supports standard 1x1 802.11ac Wave2, BT5, and MU-MIMO.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
With the old ubus dsl API, the numbers for the individual line_states and
power_states were also returned. These were not ported to the new DSL
C-API. This commit adds the missing information.
For this the internal values are mapped to numbers.
* additional JSON output for state_num:
"state_num": <map_state_number>
Since not all values are meaningful only the following values are
implemented, this can be extended if the future.
* LSTATE_MAP_NOT_INITIALIZED
* LSTATE_MAP_EXCEPTION
* LSTATE_MAP_IDLE
* LSTATE_MAP_SILENT
* LSTATE_MAP_HANDSHAKE
* LSTATE_MAP_FULL_INIT
* LSTATE_MAP_SHOWTIME_NO_SYNC
* LSTATE_MAP_SHOWTIME_TC_SYNC
* LSTATE_MAP_RESYNC
* additinal JSON output for power_level:
"power_state_num": <map_power_satte_number>,
Since there are not so many here, all are mapped.
* PSTATE_MAP_NA,
* PSTATE_MAP_L0,
* PSTATE_MAP_L1,
* PSTATE_MAP_L2,
* PSTATE_MAP_L3,
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
v6:
Add state LSTATE_MAP_NOT_INITILIZED at the beginning of the list
Start the list LSTATE_MAP with -1
Reviewed-by: Andre Heider <a.heider@gmail.com>
Placeholder DHCP user scripts were added recently.
These files make package-based installations of such scripts more difficult.
Pull user callbacks from directories instead to allow packages and users to
install co-existing scripts more easily.
References:
b4f3d93b5 odhcp6c: add a odhcp6c.user placeholder script
Signed-off-by: Leon M. George <leon@georgemail.eu>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
Placeholder DHCP user scripts were added recently.
These files make package-based installations of such scripts more difficult.
Pull user callbacks from directories instead to allow packages and users to
install co-existing scripts more easily.
References:
130118f7a netifd: add a udhcpc.user placeholder script
Signed-off-by: Leon M. George <leon@georgemail.eu>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
CRYPTO_DEV_CCP depends on X86 or ARM64
CRYPTO_DEV_CCP_DD depends on CPU_SUP_AMD or ARM64
Compiling this driver makes sense for x86 mainly. If one day support for
ARM64 board with AMD Secure Processor gets added this package may be
updated.
Trying to build this package on bcm4908 was causing:
ERROR: module 'build_dir/target-aarch64_cortex-a53_musl/linux-bcm4908_generic/linux-5.4.110/drivers/crypto/ccp/ccp-crypto.ko' is missing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
For linux 5.10, kmod-ltq-deu need to be migrated to the new crypto
API/framework.
Leave it in tree for now and enable it only for Kernel 5.4. Maybe
someone picks up the work to migrate the package.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The callback handling of the tasklet API was redesigned and the macros
using the old syntax renamed to _OLD.
The stuck queue is now passed to ndo_tx_timeout callback but not used so
far.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to SCHED_FIFO being a broken scheduler model, all users of
sched_setscheduler() are converted to sched_set_fifo_low() upstream and
sched_setscheduler() is no longer exported.
The callback handling of the tasklet API was redesigned and the macros
using the old syntax renamed to _OLD.
Signed-off-by: Mathias Kresin <dev@kresin.me>
ltq tapi
ioremap has provided non-cached semantics by default since the Linux 2.6
days and was removed with kernel version 5.6.
Signed-off-by: Mathias Kresin <dev@kresin.me>
CPU: Allwinner V40 quad-core Cortex A7 @ 1.2GHz
Memory: 1GB DDR3
Storage: SDcard, native SATA
Network: 10/100/1000M ethernet, Ampak AP6212 wifi + BT
USB: 4x USB 2.0
Installation:
Use the standard sunxi installation to an SD-card.
While the board is very similar to the M2 Ultra board
(the V40 is the automotive version of the R40), as both
the u-boot and kernel supports them separately, and some
pins are different, let's add a separate device spec.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* check image checksums before writing to flash
* only bootmenu_0...9 are working, remove bootmenu_a entry
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In preparation for H6 support (which requires a separate ATF blob), add
an envvar to the A64 boards specifying which ATF blob to use.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
valgrind does not compile any more when using a GCC 10 for MIPS with
soft float. Just remove the parts which are generating assembler which
would not work.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Default to U-Boot env in UBI if root device is not mmc block device.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Some of bpi-r64 boards have serial NAND attached to SPI bus.
Build U-Boot for booting from SPI-NAND.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Use generic functions to get env partition.
Fixes: 7043e4334f ("mediatek: mt7622: improve sysupgrade on MMC")
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
The can-dev.ko kernel module was moved in kernel 5.4.110 and 5.10.28.
Fixes: a1311df95587 ("kernel: bump 5.10 to 5.10.28")
Fixes: b0a34e886d ("kernel: bump 5.4 to 5.4.110")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Looks like 'openat', 'pipe2' and 'ppoll' are now needed, possibly due
to changes on libraries used by umdns now using slightly different
calls.
Found using
/etc/init.d/umdns trace
now use umdns, ie. cover all ubus call etc., then
/etc/init.d/umdns stop
find list of syscalls traced in /tmp/umdns.*.json
Fixes: FS#3355 ("UMDNS: does not start on master with seccomp")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Without 'BUILD_DEVICES' defined, the U-Boot related package won't be
automatically selected when building for Toradex Apalis device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
These devices never got officially supported in the tree thus it doesn't
make much sense to waste our infrastructure resources and keep building
dedicated U-Boot images for them.
CC: Petr Štetiar <ynezz@true.cz>
CC: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
Add settings for fw_printenv/fw_setenv for the Ubiquiti UniFi 6 LR
when running OpenWrt's version of U-Boot. The settings should work
equally with the unmodified version, but that has not yet been
tested.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add U-Boot build for the Ubiquiti Networks UniFi 6 LR access point.
This allows updating the bootchain to modern ARM Trusted Firmware 2.4
and U-Boot 2021.04 while keeping as much of the existing flash layout
as possible (u-boot-env, factory and eeprom partitions are retained),
gaining robust recovery vs. production dual-boot mechanism.
Add info for the Winbond W25Q512JV SPI NOR flash used in the device
and wait for GPIOs to settle after reset before checking for reset
button.
I2C connected LED controller is not supported yet.
Writing large amounts of data to SPI flash currently doesn't work due
to watchdog timeout causing reset before data write completes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use bl3 size of 0xa0000 instead of 0x80000 in NOR flash.
This results in bl3 ending at 0xc0000 which is where the legacy
bootchain typically puts U-Boot environment.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
bcm4908img is a tool managing BCM4908 platform images. It's used for
creating them as well as checking, modifying and extracting data from.
It's required by both: host (for building firmware images) and target
(for sysupgrade purposes). Make it a host/target package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Now that we can create an alternate configuration file, add two
wrapper scripts for simple access to it using the alternate
alternate application names `fw_printsys' and `fw_setsys'.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Most (all?) of the realtek devices have two u-boot config partitions
with a different set of variables in each. The U-Boot shell provides
two sets of apps to manipulate these:
printenv- print environment variables
printsys- printsys - print system information variables
saveenv - save environment variables to persistent storage
savesys - savesys - save system information variables to persistent storage
setenv - set environment variables
setsys - setsys - set system information variables
Add support for multiple ubootenv configuration types, allowing
more than one configuration file.
Section names are not suitable for naming the different
configurations since each file can be the result of multiple sections
in case of backup partitions.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Now that libcap is in OpenWrt base, we can drop our custom patch to
disable libcap support and have lldpd depend on it instead. This will
allow the monitor process to drop its privileges instead of running as
root, improving security.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Having libcap in OpenWrt base allows us to enable libcap support in
other packages in base.
In lldpd, this would allow the monitor process to drop its privileges
instead of running as root, improving security. It will also allow us to
drop our patch to disable libcap.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC
(hAP ac²), a indoor dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional antennae, USB port and five
10/100/1000 Mbps Ethernet ports.
See https://mikrotik.com/product/hap_ac2 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 128 MB
- Storage: 16 MB NOR
- Wireless:
· Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
· Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in
- 1x USB Type A port
Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that sdcard.gz image contains everything needed to boot straight
into production image, no longer force booting into recovery image on
first boot by removing the logic which implemented that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
f8899b9 netifd: bridge: set default value for igmp_snoop
327da98 netifd: add possibility to switch off route config
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Airtime policy configuration is extremely useful in multiple BSS scenarios.
Since nowadays most people configure both private and guest networks (at
least), it makes sense to enable it by default, except for the most limited
of the variants.
Size of the hostapd-basic-openssl binary (mipsel 24Kc -O2):
543944 bytes (airtime policy disabled)
548040 bytes (airtime policy enabled)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Since KERNEL_SWAP is only enabled by default for !SMALL_FLASH targets, we need
to check if the current kernel supports swap before trying to configure
zram-swap, as opkg can't check for kernel dependencies.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Switch to Actual Net Data Rate (ACTNDR) for speed reporting on lantiq VDSL modems
Refer to ITU-T G.997.1 chapter 7.5.2.8
Independent whether retransmission is used or not in a given transmit direction:
- In L0 state, this parameter reports the Net Data Rate (as specified in G.992.3, G.992.5 or G.993.2) at which the bearer channel is operating.
- In L2 state, the parameter contains the Net Data Rate (as specified in G.992.3, G.992.5 or G.993.2) in the previous L0 state.
Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com>
Reviewed-by: Andre Heider <a.heider@gmail.com>
This commit adds monitoring for a couple of DSL line features that are
present in the lantiq firmware blobs.
* G.INP ON/OFF
* Trellis encoding ON/OFF
* Virtaul Noise ON/OFF
* Bitswap ON/OFF
Difference in size for ltq-vdsl-app = 1k
Difference in size for kmod-ltq-vdsl-vr9 < 1k
Reviewed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com>
If service() is called w/o parameter then the status display for services
with multiple instances is incorrect. E.g. samba4 or wpad have 2 instances.
root@OpenWrt:~# /etc/init.d/samba4 status
running
root@OpenWrt:~# /etc/init.d/wpad status
running
Before change:
/etc/init.d/samba4 enabled stopped
/etc/init.d/wpad enabled stopped
After change:
/etc/init.d/samba4 enabled running
/etc/init.d/wpad enabled running
Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
Upstream iproute2 detects libbpf using a one-line $CC test-compile, which
normally ignores LDFLAGS. With NLS enabled however, LDFLAGS includes an
"rpath-link" linker option needed to resolve libintl.so. Its absence
causes both the compile and libbpf detection to fail:
ld: warning: libintl.so.8, needed by libbpf.so, not found (try using
-rpath or -rpath-link)
ld: libelf.so.1: undefined reference to `libintl_dgettext'
collect2: error: ld returned 1 exit status
Fix this by directly including $LDFLAGS in the test-compile command.
Reported-by: Ian Cooper <iancooper@hotmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The libbfd package definition uses $(ICONV_DEPENDS) and $(INTL_DEPENDS)
but links against neither, leading to libbfd detection failures in other
packages (e.g. bpftools) and on-target relocation problems with libintl.so:
root@OpenWrt:/# ldd /usr/lib/libbfd.so
ldd (0x77db6000)
libc.so => ldd (0x77db6000)
libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x77c6d000)
Error relocating /usr/lib/libbfd.so: libintl_dgettext: symbol not found
Add NLS-conditional linking of "libintl" to fix this. Also remove libbfd
package dependency $(ICONV_DEPENDS) which is not used during building or
linking.
Tested with QEMU on malta/be32, after building all packages from binutils,
bpftools and iproute2, using different libc options musl and glibc.
Fixes: 08e8175696 ("binutils: use nls.mk to fix libbfd link errors in
other packages")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
There is no direct linking of libintl from bpftools, only secondary linking
through libelf, so remove "-lintl" from TARGET_LDFLAGS.
Fixes: 5582fbd613 ("bpftools: support NLS, fix ppc build and update to 5.8.9")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
973cc6c compiler: actually expand block scope fix to for/while alt syntax
97bf297 compiler: ensure that alternative if/for/while syntax has own block scope
f0e2a64 tests: add missing test case for fixed switch codegen
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Introduce cmdline_get_var() to /lib/function.sh and make use of it in
export_rootdev() in /lib/upgrade/common.sh, making the code more
simple and removing one level of indentation.
Introduce get_partition_by_name() to /lib/upgrade/common.sh which is
useful on non-EFI GPT platforms like mt7622.
Remove some dead-code while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
a4355a6 firewall3: clean up the flow table detection logic
edd0dc5 firewall3: create a common helper to find strings in files
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The terminfo is required by the popular terminal multiplexer screen and
tmux, offer it by default as the size impact is minimal with 885 Bytes.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The terminfo files were all in one row which is terrible to read.
Split them over multiple lines to improve readability.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This includes several improvements and fixes:
61db17e rules: fix device and chain usage for DSCP/MARK targets
7b844f4 zone: avoid duplicates in devices list
c2c72c6 firewall3: remove last remaining sprintf()
12f6f14 iptables: fix serializing multiple weekdays
00f27ab firewall3: fix duplicate defaults section detection
e8f2d8f ipsets: allow blank/commented lines with loadfile
8c2f9fa fw3: zones: limit zone names to 11 bytes
78d52a2 options: fix parsing of boolean attributes
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This version fixes 2 security vulnerabilities, among other changes:
- CVE-2021-3450: problem with verifying a certificate chain when using
the X509_V_FLAG_X509_STRICT flag.
- CVE-2021-3449: OpenSSL TLS server may crash if sent a maliciously
crafted renegotiation ClientHello message from a client.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Building with MIPS16 was disabled in 2013 due to an issue with GCC TLS:
https://dev.archive.openwrt.org/ticket/13572. But after the problematic
GCC version was retired, this change wasn't revisited.
Re-enable MIPS16 builds to reduce average elfutils library sizes ~10%.
This was compile-tested on malta/mips32be and malta/mips32le, and linked
with iproute2 for run-testing. Package sizes follow:
Library MIPS16:=0 MIPS16:=1
------- --------- ---------
libelf1 43217 37492
libasm1 12481 11658
libdw1 229723 205793
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
NXP 74HC153 is a GPIO expander. Its original source cide sits in ar71xx
architecture tree. It has been slightly modified to get GPIO pin
configuration from the device tree rather than a MACH file.
Changes to the source file:
- Remove struct nxp_74hc153_config
- in nxp_74hc153_probe(), fetch GPIO configuration from device tree
- allow GPIO framework decide the base number by passing -1 to it
- remove support for kernel versions below 4.5.0
- add OF device compatibility string
Create a package for inclusion in image.
References: https://lore.kernel.org/linux-gpio/545111184.50061.1615922388276@ichabod.co-bxl/
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
[added link to driver usptreaming work in progress]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Moved to packages repo because it was considered
non-essential for most router configurations.
Signed-off-by: Jan Pavlinec <jan.pavlinec@nic.cz>
[shorten commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Instead of doing uci commit and reload_config for each setting do it
only once when one of these options was changed. This should make it a
little faster when both conditions are taken.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Without this change the config is only committed, but the uhttpd daemon
is not reloaded. This reload is needed to apply the config. Without the
reload of uhttpd, the ubus server is not available over http and returns
a Error 404.
This caused problems when installing luci on the snapshots and
accessing it without reloading uhttpd.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Dependency tracking for kmod-sound-hda-core is fragile. Enabling some sound
codecs (Realtek, Conexant, Sigmatel) implicitly adds a kmod-ledtrig-audio
dependency, while an enabled kmod-ledtrig-audio can be picked up through
enabling others (e.g. kmod-sound-hda-intel), and the behaviour can change
across kernel versions.
As kmod-ledtrig-audio is under 2KB, make it an unconditional dependency.
Fixes: a374b8f190 ("kernel: 5.10: update sound modules")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
When $(FPIC) gets expanded on the command line (for instance
when setting environment variables for libtool, configure, or
make) we can't count on it not needing quoting (i.e. it could
contain multiple flags separated with spaces).
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Now that ujail supports seccomp also on Aarch64, add missing syscall
'fstat' to the list of allowed syscalls.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable seccomp features on Aarch64.
3e88c6f jail/seccomp: add support for aarch64
c23d8bf trace: fix build on aarch64
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
With kernel 5.10, exfat is out of staging and in tree.
Added small hack to make it work with kernel 5.4 as well.
Added removed config options for 5.4 to generic config.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[Set CONFIG_EXFAT_ config options to default values]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This change was investigated previously [1] but not deemed necessary. With
the recent addition [2] of modern BPF loader support, however, tc gained
dependencies on libelf and libbpf, with a larger installation footprint.
Similar to ip-tiny/ip-full, split tc into tc-full and tc-tiny variants,
where the latter excludes the eBPF loader, uses a smaller executable, and
avoids libelf and libbpf package dependencies. Both variants provide the
'tc' virtual package, with tc-tiny as the default.
The previous tc package included a loadable module for iptables actions.
Separate this out into a common package, tc-mod-iptables, which both
variants depend on. Some package sizes on mips_24kc:
Before:
148343 tc_5.11.0-1_mips_24kc.ipk
After:
144833 tc-full_5.11.0-2_mips_24kc.ipk
138430 tc-tiny_5.11.0-2_mips_24kc.ipk (and no libelf or libbpf)
4115 tc-mod-iptables_5.11.0-2_mips_24kc.ipk
Also fix up some Makefile indentation.
[1] https://github.com/openwrt/openwrt/pull/1627#issuecomment-447619962
[2] b048a305a3 ("iproute2: update to 5.11.0")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The link equalizer sch_teql.ko of package kmod-sched relies on a hotplug
script historically included in iproute2's tc package. In previous
discussion [1], consensus was the hotplug script is best located together
with the module in kmod-sched, but this change was deferred at the time.
Relocate the hotplug script now. This change also simplifies adding a tc
variant for minimal size with reduced functionality.
[1] https://github.com/openwrt/openwrt/pull/1627#issuecomment-447923636
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This patch has been submitted upstream to fix an error reported by a few
users. One instance seen using gcc 10.2.0, binutils 2.35.1 and musl 1.1.24:
bpf_glue.c: In function 'get_libbpf_version':
bpf_glue.c:46:11: error: 'PATH_MAX' undeclared (first use in this function);
did you mean 'AF_MAX'?
46 | char buf[PATH_MAX], *s;
| ^~~~~~~~
| AF_MAX
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Update file paths for kmod-sound-hda-intel and reflect new dependency of
kmod-sound-hda-core on kmod-ledtrig-audio.
Reported-by: Javier Marcet <javier@marcet.info>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add conditional dependency on kmod-of-mdio due to mdio_devres.c code:
#if IS_ENABLED(CONFIG_OF_MDIO)
...
EXPORT_SYMBOL(devm_of_mdiobus_register);
#endif /* CONFIG_OF_MDIO */
Fixes: 95a3741d17 ("kernel: support new mdio_devres.ko module in 5.10")
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
kdump was removed in 7acd257ae67b4ca94f8c23cb8bda0ee0709b9216
gdb can be used as an alternative.
Remove autoreconf. It's not needed as the configure files are already
generated.
Remove upstreamed patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
If the environment variable FILTER is set before compilation,
compilation of the ppp-package will fail with the error message
Package ppp is missing dependencies for the following libraries:
libpcap.so.1
The reason is that the OpenWrt-patch for the Makefile only comments
out the line FILTER=y. Hence the pcap-library will be dynamically
linked if the environment variable FILTER is set elsewhere, which
causes compilation to fail. The fix consists on explicitly unsetting
the variable FILTER instead.
Signed-off-by: Eike Ritter <git@rittere.co.uk>
This fixes writing to the U-Boot environment by making the partition
writable and setting the correct flash sector size of 128K.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Allow selecting either SATA or PCIE functionality using uImage.FIT
configurations and device-tree overlays.
By default, PCIE1 is selected (as it has been before this change).
To select SATA instead, you can do this now:
fw_setenv bootconf config-mt7622-bananapi-bpi-r64-sata
and reboot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Commit b5b0796a13 added an uint32_t to mtd.h without including stdint, which
results in a compilation error for those files not including stdint.h.
In file included from imagetag.c:36:
mtd.h:15:8: error: unknown type name 'uint32_t'
extern uint32_t opt_trxmagic;
^~~~~~~~
imagetag.c: In function 'trx_fixup':
imagetag.c:180:10: warning: unused variable 'res' [-Wunused-variable]
ssize_t res;
^~~
imagetag.c:177:14: warning: unused variable 'scan' [-Wunused-variable]
void *ptr, *scan;
^~~~
imagetag.c: In function 'trx_check':
imagetag.c:246:27: warning: initialization discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
struct bcm_tag *tag = (const struct bcm_tag *) buf;
^
make[3]: *** [<builtin>: imagetag.o] Error 1
Fixes: b5b0796a13 ("mtd: add option for TRX magic to fixtrx")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This release of Mbed TLS provides bug fixes and minor enhancements. This
release includes fixes for security issues.
Security fixes:
* Fix a buffer overflow in mbedtls_mpi_sub_abs()
* Fix an errorneous estimation for an internal buffer in
mbedtls_pk_write_key_pem()
* Fix a stack buffer overflow with mbedtls_net_poll() and
mbedtls_net_recv_timeout()
* Guard against strong local side channel attack against base64 tables
by making access aceess to them use constant flow code
Full release announcement:
https://github.com/ARMmbed/mbedtls/releases/tag/v2.16.10
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
This adds support for the Buffalo WSR-2533DHP2.
The device uses the Broadcom TRX image format with a special magic. To
be able to boot the images or load them they have to be wrapped with
different headers depending how it is loaded.
There are multiple ways to install OpenWrt on this device.
Boot ramdisk from U-Boot
----------------------------
This will load the image and not write it into the flash.
1. Stop boot menu with "space" key
2. Select "System Load Linux to SDRAM via TFTP."
3. Load this image:
openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-initramfs-kernel.bin
4. The system boots the image
Write to flash from U-Boot
-----------------------------
This will load the image over tftp and directly write it into the flash.
1. Stop boot menu with "space" key
2. Select "System Load Linux Kernel then write to Flash via TFTP."
3. Load this image:
openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory-uboot.bin
4. The system writes this image into the flash and boots into it.
Write to flash from Web UI
-----------------------------
This will load the image over over the Web UI and write it into the flash
1. Open the Web UI
2. Go to "管理" -> "ファームウェア更新"
3. Select "ローカルファイル指定" and click "更新実行"
4. Load this image:
openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory.bin
5. The system writes this image into the flash and boots into it.
Specifications
-------------------
* SoC: MT7622 (4x4 2.4 GHz Wifi)
* Wifi: MT7615 (4x4 5 GHz Wifi)
* Flash: Winbond W29N01HZ 128MB SLC NAND
* RAM 256MB
* Ethernet: Realtek RTL8367S (5 x 1GBit/s, SoC via 2.5GBit/s)
Co-Developed-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Buffalo uses the TRX header with a different magic and even changes this
magic with different devices. This change allows to specify the header
to use as a command line argument.
This is needed for the Buffalo WSR-2533DHP2 based on mt7622.
Co-Developed-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
