mt76x8 uses esw_rt3050 driver, which does not accept mediatek,portmap with
string values. Convert the strings to integers to make it work.
According to its switch setup, WRTnode 2P/2R have a WAN port at port 0,
so the correct value should be 0x3e.
tplink_8m.dtsi uses "llllw", but it does not match switch setups of any
device using the DTSI. Remove it from the DTSI and add correct value to DTS
for each device.
These devices have a WAN port at port 0. Set the value to 0x3e.
- tplink,archer-c20-v4
- tplink,archer-c50-v3
- tplink,tl-mr3420-v5
- tplink,tl-wr840n-v4
- tplink,tl-wr841n-v13
- tplink,tl-wr842n-v5
These devices have only one ethernet port. They don't need portmap setting.
- tplink,tl-wa801nd-v5
- tplink,tl-wr802n-v4
- tplink,tl-wr902ac-v3
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(backported from commit 7a387bf9a0)
[removed TL-WR841N v14 which is not present in 19.07]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Use diag.sh version used for other targets supporting different leds
for the different boot states.
The existing led sequences should be the same as before.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the ranges property to the PCI bridges where missing. Add the unit
address to PCI bridge where missing.
Rework the complete rt3883 pci node. Drop the PCI unit nodes from the
dtsi. They are not used by any dts file and should be rather in the dts
than in the SoC dtsi. Express the PCI-PCI bridge in a clean devicetree
syntax. The ralink,pci-slot isn't used by any driver, drop it. Move the
pci interrupt controller out of the pci node. It doesn't share the same
reg and therefore should be an independent/SoC child node.
Move the pci related rt3883 pinctrl setting to the dtsi instead of
defining the very same for each rt3883 board.
If the device_type property is used for PCI units, the unit is treated
as pci bridge which it isn't. Drop it for PCI units.
Reference pci-bridges or the pci node defined in the dtsi instead of
recreating the whole node hierarchy. It allows to change the referenced
node in the dtsi without the need to touch all dts.
Fix the PCI(e) wireless unit addresses. All our PCI(e) wireless chips
are the first device on the bus. The unit address has to be the bus
address instead of the PCI vendor/device id.
Signed-off-by: Mathias Kresin <dev@kresin.me>
TP-Link Archer C50 v3 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7612E.
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power switch
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Flash instruction:
The only way to flash LEDE image in ArcherC50v3 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC50v3-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
