The src-include method allows recursive inclusion of feeds.conf snippets.
This can for example be used for adding static local feeds to
feeds.conf.default without ever having to update the local feeds.conf:
src-include defaults feeds.conf.default
src-link custom /usr/local/src/lede/custom
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Extend the packageauxvars database to keep a list of possible package
dependencies for each provider, then utilize this information in buildroot
to resolve the ABI version dependencies of dependent packages up to five
levels deep.
This should properly trigger rebuilds for packages indirectly depending
on other packages whose ABI_VERSION changed.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The Makefile was missing dependencies on *c_shipped, so changes never
triggered a rebuild. Add these as optional dependencies so their absence
isn't treated as an error.
In addition, fix a typo preventing the zconf.lex.o from being removed on
clean.
Fixes: 9d5510a500 ("build: add new menuconfig code based on linux 3.9")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
When there are multiple packages providing a meta-package, it is
possible to to create a config where a package is selected as =y, but
all of its dependency providers are just selected as =m. This is due to
the selection statement being just
config PACKAGE_foo
select PACKAGE_bar if !PACKAGE_baz
which is already fulfilled by PACKAGE_bar=m. Fix this by properly
comparing the selection states:
config PACKAGE_foo
select PACKAGE_bar if PACKAGE_baz<PACKAGE_foo
Also invert the select conditions to improve readability.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
[slightly reword commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Since commit 31847b67bec0 ("kconfig: allow use of relations other than
(in)equality") it is possible to use relational operators in Kconfig
statements. However, those operators give unexpected results when
applied to bool/tristate values:
(n < y) = y (correct)
(m < y) = y (correct)
(n < m) = n (wrong)
This happens because relational operators process bool and tristate
symbols as strings and m sorts before n. It makes little sense to do a
lexicographical compare on bool and tristate values though.
Documentation/kbuild/kconfig-language.txt states that expression can have
a value of 'n', 'm' or 'y' (or 0, 1, 2 respectively for calculations).
Let's make it so for relational comparisons with bool/tristate
expressions as well and document them. If at least one symbol is an
actual string then the lexicographical compare works just as before.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[rebased against OpenWrt kconfig, slightly reword commit message]
(backported from upstream 9059a3493efea6492451430c7e2fa0af799a2abb)
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The pregenerated `zconf.hash.c` and `zconf.lex.c` files have not been
kept in sync with their respective `*.y` and `*.l` sources in the past
causing our kconfig implementation to not recognize important kconfig
grammer elements such as relational `<`, `<=`, `>` and `>=` operators.
Fixes: 2d7e602381 ("scripts/config: sync with latest linux upstream")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
[reword commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Most of the patches are copied over from GCC 8.3.
The following patches are backported from the GCC 9.X development branch:
toolchain/gcc/patches/9.1.0/970-recompute-dom-fast-queries-before-vn.patch
toolchain/gcc/patches/9.1.0/975-g++-ICE-with-generic-lambda.patch
The specs file changed with gcc 9, now it contains "%@{L*}" instead of
"%{L*}" in older GCC versions.
Signed-off-by: Joseph Benden <joe@benden.us>
Adds support to && operand in DEPENDS. Also, fixes generation of ||
dependencies by scripts/package-metadata.pl.
The precedence order from higher to lower is && then ||. Use of
parentheses to change the order is not supported. As before, they are
silently ignored. Use them for readability only.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [DMARC removal]
When looping through a package's STAGING_FILES_LIST (a list of
file/directory paths delimited by newlines), if the path contains
spaces, then the path will be split by the while loops, and the
file/directory will not be deleted/removed.
This sets the internal field separator to the newline only so that the
entire path is considered when deleting/removing.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
If the target supports a newer kernel version that is not used by default
yet, it can be enabled with this option
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We only enabled pcnet driver for malta machine, and x86/legacy target
was supposed to only support e1000 model
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This should make it easier to set up and possibly provide a "work out of
the box" experience for most test usage. Typical wan&lan networking
setup is only two characters argument away.
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
Commit 8bf500eb79 added support for qemu usage without networking
support but broke networking support as -n and -z do not work with
unquoted argument; fix this by quoting the arguments.
Fixes 8bf500eb79
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
ar71xx is in the process of being deprecated as a target accepting new
devices. The replacement target for the same hardware is DTS
based ath79.
Switch the default build target selection from ar71xx to ath79.
This is intended to encourage DTS takeup & support for ath79 and longer
term will also aid kernel upstream support.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Currently it's not possible to test boot squashfs root images, so this
patch now allows this use case as well.
Cc: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Currently it's not possible to test boot squashfs root images, so this
patch now allows this use case as well.
Cc: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
For basic tests it's not necessary to have the networking setup and this
allows testing as a normal user as well, without root privileges.
So this patch adds `--no-network` long option or `-n` short option,
which allows starting QEMU without network.
Cc: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The script always exits with value 0, even if some of the commands fail.
This can potentially create broken, unbootable images, e.g. when
make_ext4fs fails due to TARGET_KERNEL_PARTSIZE being too small for the
kernel. Avoid this by failing the script when any command fails.
Acked-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Having image metadata (and signature) appended is a condition for
semi-automated sysupgrade, hence IB needs to be able to tell which
images will end up with metadata.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The current eva_ramboot.py script is currently only compatible with
Lantiq based AVM devices. For IPQ40xx devices, the offset needs to be
changed. Also an alignment is not necessary here.
Adjust the script to be able to pass an optional offset to load the
image to. In case no offset is provided, the script behaves exactly as
before this commit.
Signed-off-by: David Bauer <mail@david-bauer.net>
Qualcomm SDK (QSDK) sysupgrade compatible images for IPQ40xx, IPQ806x
and IPQ807x use FIT format together with 'dumpimage' tool from U-Boot
for verifying and extracting them. Based on 'images' sections names,
corresponding mtd partitions are flashed. For example, in case of
NOR-only boards, below mapping is used (section name -> mtd name):
hlos* -> 0:HLOS
rootfs* -> rootfs
And for boards with NAND (kernel inside UBI):
ubi* -> rootfs
Above mappings come from unmodified QSDK sources and might be wrong for
boards running custom or modified QSDK-based firmware. Some of vendors
adjust them to meet their modified mtd layout or features like recovery
or dual-image support.
This adds simple script 'mkits-qsdk-ipq-image.sh' (based on 'mkits.sh')
for generating FIT images tree source files, compatible with the QSDK
sysupgrade format. Resulting images can be used for initial (factory ->
OpenWrt) installation and would work both in CLI and GUI.
The script is universal in a way it allows to include as many sections
as needed. To make use of it, two generic/basic build recipes for NOR
and NAND based boards are also included in 'image-commands.mk':
Build/qsdk-ipq-factory-nand
Build/qsdk-ipq-factory-nor
Example usage for board with UBI in NAND:
IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This can be used to set machine options like highmem=off for running old
armvirt/32 kernel lacking LPAE support with QEMU version 3.0 or later
[1] Armv7 guest fails to boot with qemu-3.0.0-1,
https://bugzilla.redhat.com/show_bug.cgi?id=1633328#c5
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Use `stat -L` instead of `ls -l` to follow symbolic links when obtaining
the file size of .ipk archives.
Without this change, the size of the symlink, not the size of the target
file is encoded in the package index file.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This fixes two issues with cleaning package files from STAGING_DIR:
* CleanStaging currently can only remove files and not directories. This
changes CleanStaging to use clean-package.sh, which does remove
directories.
* Because of the way directories are ordered in the staging files list,
clean-package.sh currently tries (and fails) to remove parent
directories before removing subdirectories. This changes
clean-package.sh to process the staging files list in reverse, so that
subdirectories are removed first.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
This commit adds the 'Build/linksys-image' rule and the
'linksys-image.sh' script to the build system.
This change is needed for generating factory images for the Linksys
EA6350v3 device. Without this patch, only valid sysupgrade images can be
generated. With this patch, users can flash the device without the
need of physical access or disassembly.
Signed-off-by: Ryan Pannell <ryan@osukl.com>
Signed-off-by: Oever González <notengobattery@gmail.com>
When a library package specifies additional provides, e.g. libncurses
which provides libncursesw, we should also append the abi version
suffix to each provide, since there may be more than one package
providing the virtual library.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Package archives built before commit e6bcf1e4ac
("build: add ABI_VERSION to binary package names") lack the SourceName
control file field which caused ipkg-remove to skip such archives.
Add fallback code that matches the files by their basename followed by
an underscore, similar to how the old cleanup code worked.
Fixes: #2067
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add the ABI_VERSION source makefile variable to the binary package basename
and resolve source dependencies on packages with ABI_VERSION set to such
expanded names.
If for example a package specifies DEPENDS:=libopenssl while the OpenSSL
Makefile specifies ABI_VERSION:=1.0.0, the resulting ipk control data
dependency will be "Depends: libopenssl1.0.0" and the libopenssl ipk file
will be called "libopenssl1.0.0_<version>_<arch>.ipk".
The next time a library such as OpenSSL is updated to an incompatible
version, the ABI_VERSION shall be changed accordingly to prevent opkg from
simply upgrading to an incompatible library without considering the
dependencies of already installed packages.
Also introduce another "SourceName" control field which is required by
the newly introduced "scritps/ipkg-remove" to determine the proper related
.ipk files to delete upon buildroot package clean operations.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Subdequent commits need this information to resolve the ABI version when
computing binary ipk dependencies.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Subsequent commits will put more auxiliary information into this file,
such as the per-package ABI version, so rename the metadata script
subcommand and file names accordingly.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Tar will automatically record the user/group ID and name for
files/directories. This reduces the reproducibility of the sysupgrade.tar
because most of the people don't use the same username as the OpenWrt
buildserver.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The file ordering in the current sysupgrade depends on the order of file in
a filesystem. This is often already in a sane (alphabetical order) but this
is not always the case. For example, the OpenWrt build servers return a
different ordering.
This breaks the reproducibility of the sysupgrade tarballs significantly
and also resulted in images which cannot be used for upgrades on devices
like the OpenMesh A42/A62.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2efe776 introduces rpath checks with the commit message:
> Remove all rpath entries which do not point to a location below /lib or
> /usr/lib and which do not begin with '$ORIGIN'.
However the implementation failed to support rpath entries with only the
'$ORIGIN' token and no trailing slash, so allow these as well.
Signed-off-by: Yorkie Liu <yazhong.liu@rokid.com>
[reword commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When the SOURCE_DATE_EPOCH environment variable is set, use it to
override the timestamps of .ipk archive contents.
This ensures that .ipk archives built in environments without SCM
metadata (mainly the SDK) are reproducible between different runs.
Ref: https://github.com/openwrt/packages/issues/6954
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This updates these two files to commit 2fa97a8a0ed3 ("config.guess
(amd64:CYGWIN*:*:*, x86_64:CYGWIN*:*:*): Set master") which is the
current master of
https://git.savannah.gnu.org/gitweb/?p=config.git;a=summary
This contains updates for multiple architectures and will unbreak the
build on the x32 ABI.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The OM2P(-HS)v4 got a variant which uses a slightly different flash. The
standard versions used a flash with 256KB blocks which is no longer
available. The replacement flash uses a flash with 64K blocks.
The padding for the image rootfs is already for 64K and 256K and thus can
be flashed on the device without any problems. Unfortunately, the
bootloader will check $rootfs_size (rounded down to the nearest 64k block)
minus 1x 64k. But it is now possible that the new JFFS2 rootfs_data starts
even earlier and modifies the checked region. The check will then fail and
the backup image (when available) will be booted.
Just setting it to the same number of skipped blocks as other 64K models
avoids this problem.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
When Package/xx/conffiles only contains directories that are empty at
package time, conffiles.resolved will be missing and the following
error messages will appear in the build log.
/home/yousong/git-repo/openwrt/openwrt/scripts/ipkg-build -c -o 0 -g 0 /home/yousong/git-repo/openwrt/openwrt/build_dir/target-mips_24kc_musl/linux-malta_be/openvswitch-2.10.0/ipkg-mips_24kc/openvswitch-common /home/yousong/git-repo/openwrt/openwrt/bin/packages/mips_24kc/packages
mv: cannot stat 'CONTROL/conffiles.resolved': No such file or directory
chmod: cannot access 'CONTROL/conffiles': No such file or directory
It will not break the ipkg-build process. The change is merely cosmetic
to not cause confusion when reading logs
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The need arises from building Open vSwitch kernel datapath modules, e.g.
- kmod-openvswitch from Linux upstream
- kmod-openvswitch-intree from openvswitch source code
where both provides virtual package "kmod-openvswitch" for userspace
packages to select and depend on
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Previous refactoring of the script moved the LDSO detection into a
file-not-exists condition, causing onyl the very first executable to
get bundled.
Solve the problem by unconditionally checking for LDSO again.
Fixes: 9030a78a71 ("scripts: bundle-libraries: prevent loading host locales")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The current make-ras.sh image generation script for the ZyXEL NBG6617
has portability issues with bash. Because of this, factory images are
currently not built correctly by the OpenWRT buildbots.
This commit replaces the make-ras.sh by C-written mkrasimage.
The new mkrasimage is also compatible with other ZyXEL devices using
the ras image-format.
This is not tested with the NBG6616 but it correctly builds the
header for ZyXEL factory image.
Signed-off-by: David Bauer <mail@david-bauer.net>
Binary patch the bundled glibc library to inhibit loading of host locale
archives in order to avoid triggering internal libc assertions when
invoking shipped, bundled executables.
The problem has been solved with upstream Glibc commit
0062ace229 ("Gracefully handle incompatible locale data") but we still
need to deal with older Glibc binaries for some time to come.
Fixes FS#1803
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Use Time::HiRes when available and fallback to raw syscall interface
when not. If that fails too, simply report 0, 0 as real time.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Replace the GNU time program invocation with a simple Perl script reporting
the timing values. Since we require Perl anyway for the build system, we can
as well use that instead of requiring a random GNU utility rarely installed
by default.
Fixes: ff6e62b288 ("build: log time taken by each packages/steps")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Compiler is producing the warning:
warning: format not a string literal and no format arguments
[-Wformat-security]
This patch makes the format a literal string in printf statements.
This with: gcc version 7.3.0 (Ubuntu 7.3.0-16ubuntu3) in Ubuntu 18.04
Signed-off-by: Paul Schulz <paul@mawsonlakes.org>
Allow enabling/commenting/disabling each feed individually by using a
tristate config symbol.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The src-dummy method does not actually obtain any feed, but it can be used
to insert addtional entries into the opkg distfeeds.conf. This is useful to
make package feeds available to users without requiring the corresponding
source feeds to be available during build.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
- Make the code more GitHub-specific
- Requires mirror hash to work with .gitattributes
- Use different API depending on whether PKG_SOURCE_VERSION is a
complete commit id or other ref types like tags
- Fix removing symbolic link
- pre-clean dir_untar for possible leftovers from previous run
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Move SCAN_DEPS to scan.mk to eliminate redundancy with scripts/feeds
Add image/*.mk to SCAN_DEPS for targets to pick up newly added devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
A new python script scripts/download.py is added to fetch tarballs using
GitHub archive API [1], then repack in a reproducible way same as the
current DownloadMethod/git
GitHub imposes a 60 reqs/hour rate limit on unauthenticated API
access[2]. This affects fetching commit date for feeding tar --mtime=
argument. However, observation indicates that archive download is NOT
subject to this limit at the moment. In the rare cases where download
fails because of this, we will falback to using DownloadMethod/git
The missing piece in the GitHub API is that it cannot provide in the
tarball dependent submodules's source code. In that case, the
implementation will also fallback to using DownloadMethod/git
[1] Get archive link, https://developer.github.com/v3/repos/contents/#get-archive-link
[2] Rate limiting, https://developer.github.com/v3/#rate-limiting
v2 <- v1:
- allow passing multiple urls with --urls argument
- add commit ts cache. can be helpful on retry
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This patch adds support for ZyXEL NBG6617
Hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR: 32 MiB Macronix MX25L25635F
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS
Serial:
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
pre-soldered. Pinout:
1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX
first install / debricking / restore stock:
0. Have a PC running a tftp-server @ 192.168.1.99/24
1. connect the PC to any LAN-Ports
2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
into the tftp-server root directory and rename it to just "ras.bin".
3. power-cycle the router and hold down the the WPS button (for 30sek)
4. Wait (for a long time - the serial console provides some progress
reports. The u-boot says it best: "Please be patient".
5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
flashes fast at the same time. You have to reboot the device and
it should then come right up.
Installation via Web-UI:
0. Connect a PC to the powered-on router. It will assign your PC a
IP-address via DHCP
1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
2. Go to the "Expert Mode"
3. Under "Maintenance", select "Firmware-Upgrade"
4. Upload the OpenWRT factory image
5. Wait for the Device to finish.
It will reboot into OpenWRT without any additional actions needed.
To open the ZyXEL NBG6617:
0. remove the four rubber feet glued on the backside
1. remove the four philips screws and pry open the top cover
(by applying force between the plastic top housing from the
backside/lan-port side)
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6617> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6617>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6617> ATSE NBG6617
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6617> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6617> ATGU
|NBG6617#
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
When sending script/env diff's output to a file or pipeline, you
don't want escape characters for ANSI color sequences fouling the
byte stream.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SourceForge has supported HTTPS for its downloads for a long time now.
I have not been able to see any failures resulting from this change.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This allegedly fixes compilation of the library bundler preload library on
Apple OS X. The resulting executables have not been runtime tested due to a
lack of suitable test hardware.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Use the EVA bootloader to load a small linux system into the ram and boot
it from there:
./scripts/flashing/eva_ramboot.py 192.168.178.1 path/to/initramfs-kernel.bin
Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE>
Acked-by: John Crispin <john@phrozen.org>
[reworded commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Some devices only boot when a special config is found in the image and
completely ignore the default entry during the selection. These devices can
now use the variable DEVICE_DTS_CONFIG in their device image definition.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
/lib/functions.sh can deal with Require-User specifications that only
contain a group, but no user. Adjust metadata.pm to allow such
specifications as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
``make xconfig`` toplevel target will invoke ``make qconf`` inside
./scripts/config directory, which results a ``qconf`` executable.
This commit removes leftover ``qconf`` executable during ``make
config-clean``.
Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
Remove references to /etc/, /lib/ and /usr/ from the bundled ld.so
interpreter using simple binary patching.
This is needed to prevent loading host system libraries such as
libnss_compat.so.2 on foreign systems, which may result in ld.so
inconsistency assertions.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Prevent emitting broken dependency statements when resolving references
to non existing packages to an empty provider list.
Fixes: 47d6b05ad3 ("metadata: always resolve dependencies through provides list")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The logic for choice between source and binary packages was reversed.
Fixes: 52719c2b67 "metadata: scripts/feeds: distinguish between source
and binary packages, resolve virtual dependencies"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Package "features" seem to be unused for some time. In any case, custom
Config.in snippets and package PROVIDES are a much more flexible way to
express similar options.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Properly resolve build depends to source packages and runtime depends to
binary packages. Dependencies on virtual packages are resolved to the first
provider now.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Instead of adding virtual packages to the normal package list, keep a
separate list for provides, make each package provide itself, and resolve
all dependencies through this list. This allows to use PROVIDES to replace
existing packages.
Fixes FS#837.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Runtime depends cannot have a buildtype suffix, and they never refer to
source package names. In addition, this adds warnings about unsatisfiable
dependencies.
Furthermore, this change fixes the generation of conditional build
dependencies for virtual packages provided by different source packages.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Target build depends are similar to host build depends in that they refer
to source packages rather than binary packages. Therefore, it makes sense
to handle them together, rather than putting them in a list together with
runtime depends and trying to figure out if the entries refer to source or
to binary packages afterwards.
This does lead to PKG_BUILD_DEPENDS entries referring to binary package
names not working anymore, which requires some fixes in the package
repositories.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This feature has been unused for years, and its scope is too limited to be
actually useful.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Every single reference to subdir was concatenated with the source package
name, so it makes sense to store the concatenated value instead.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
We often want to access fields of a source packages through pkg->{src}.
Allow accessing them directly instead of resolving the source hash through
srcpackages.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
All build dependencies are between source packages. Interating over source
rather than binary packages simplifies parts of the code and prepares
further improvement.
As a side effect, this changes the implicit default variant of a few
packages (the first defined is used now instead of the lexicographically
first).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Build types are a property of source rather than binary packages. This is a
preparation for followup cleanup.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Turn the srcpackage values into hashes to allow storing more information
than just binary package names.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Nothing explicitly depends on base-files, and even if it would, it would
not cause any problems. Remove the unused special case.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The new build commands operate on the input image and use it again as
output image. This conflicts with the way combined-ext-image.sh was
operating. It required that input and output files are different files and
and that it can write freely to the output file.
This can be avoided when all intermediate build steps by
combined-ext-image.sh are done in a temporary directory. The output file is
then only overwritten in the last step.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
A self-dependency is not an error worth a warning; rather, it is very
common: whenever there are dependencies between different binary packages
originating from the same source package, such dependencies occur. Not
actually generating dependency rules is correct, but already handled a few
lines below.
A typo prevented this redundant rule from working, which is the reason the
warning was not actually printed.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
When calling a download target, hash verification is now completely
skipped if we set PKG_HASH=skip.
This allows to easily bump package version:
$ make package/<mypackage>/download PKG_HASH=skip V=s
$ make package/<mypackage>/check FIXUP=1 V=s
This will download the new version of the package, and then automatically
update PKG_HASH with the hash of the new version. Of course, it is still
the responsibility of the packager to ensure that the new tarball is
legitimate, because it is downloaded from a possibly untrusted source.
Fixes: b30ba14e ("scripts/download.pl: fail loudly if provided hash is unsupported")
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: John Crispin <john@phrozen.org>
This commit adds qconf related files to .gitignore.
The files to be tracked are qconf.cc, qconf.h, and images.c.
The files to be ignored are qconf*.o, qconf*, qconf.moc, and
.tmp_qtcheck.
Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
qconf is kconfig UI utilizing QT toolkit. This makes it possible to use
graphical interface interaction to configure LEDE build target.
This commit adds qconf target to ./script/config/Makefile to be used by
toplevel ``make xconfig`` later.
Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
Fix multiple syntax errors in shelscripts (of packages only)
These errors were causing many conditions to not working properly
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[increase PKG_RELEASE, drop command substitution from directip.sh]
Signed-off-by: Mathias Kresin <dev@kresin.em>
Currently, if the provided hash is unsupported (length different from 32
or 64 bytes), we happily download the requested file without any kind of
checksum verification.
This is quite dangerous and may provide a false sense of security, because
a single typo in the hash (e.g. one character deleted by mistake) may skip
checksum verification entirely.
Instead, fail immediately if we don't support the provided hash.
In particular, if an external package repository decides to change the
hash algorithm one day, we will now fail loudly instead of skipping
checksum verification without complaints.
Note: if some users of scripts/download.pl knowingly provide an empty hash
because they don't need checksum verification, this change will break
them. This does not seem to be the case currently, but if this feature is
ever needed, an option should be added to download.pl instead of relying
on the hash being empty.
Fixes: eaa4eba10a ("scripts/download.pl: add SHA-256 support")
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
If CONFIG_DOWNLOAD_FOLDER is set to for example "~/dl", the download
script fails to create the .hash and .dl files with the following
errors:
Cannot create file ~/dl/dropbear-2017.75.tar.bz2.dl: No such file or directory
sh: 1: cannot create ~/dl/dropbear-2017.75.tar.bz2.hash: Directory nonexistent
If the tarball already exists in the ~/dl dir, it's properly found and
used, so this issue only affects the download.pl script.
This patch calls glob() on the target dir parameter, which will expand `~`.
Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
When a package declares a PKG_BUILD_DEPENDENCY or HOST_BUILD_DEPENDENCY on
a not existing build type, the metadata script will emit a reference to an
unresolvable build target in tmp/.packagedeps, causing the make process to
fail hard in a way not catchable by the IGNORE_ERRORS mechanism.
In a situation where a package "test-a" declares a build dependency
"PKG_BUILD_DEPENDS:=test-b/host" while the Makefile of "test-b" does not
implement a HostBuild, make fails with an unrecoverable error in the form:
make[1]: Entering directory '...'
make[1]: *** No rule to make target 'package/test-b/host/compile',
needed by 'package/test-a/compile'. Stop.
make[1]: Leaving directory '...'
.../toplevel.mk:200: recipe for target 'package/test-a/compile' failed
make: *** [package/test-a/compile] Error 2
Extend the metadata generation script to catch such unresolved references
and emit a visable warning upon detection.
After this change, the script will emit a warning similar to:
WARNING: Makefile "package/test-a/Makefile" has a build dependency on
"test-b/host" but "package/test-b/Makefile" does not implement a
"host" build type
Fixes a global build cluster outage which occured after the "python-cffi"
feed package removed its HostBuild which the "python-cryptography" package
build-depended on.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Only mangle argv[0] of the first executed process and leave the argument
vector of subsequent invocations as-is to allow child programs to properly
discover resources relative to their binary locations.
Fixes "cc1" discovery when executing the host gcc through the bundled
"ccache" executable.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Internet2 isn't considered a trusted issuer meaning that https links to
rit.edu will fail.
The host mirror.csclub.uwaterloo.ca has a trusted SSL cert and peering
is good so it can replace rit.edu without performance issues.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[Jo-Philipp Wich: rewrapped commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Commit 72d751cba9 "build: rework library bundling" introduced a new helper
binary "runas" whose sole purpose was mangling the argv vector passed to
the actual called ELF image so that the renamed executable could obtain the
proper name from argv[0].
This approach, however totally defeated the purpose of calling bundled ELF
executables through the shipped ld.so loader since the execv() invocation
performed by "runas" would cause the kernel the interprete the final program
image through the system ELF loader again.
To solve the problem, use an alternative approach of shipping a shared object
"runas.so" which uses an ELF ".init_array" function pointer to obtain the
argv[] vector of the to-be-executed main() function and mangle it in-place.
The actual argv[0] value to use is communicated out-of-band using an
environment variable "RUNAS_ARG0" by the shell wrapper script. The wrapper
script also takes care of setting LD_PRELOAD to instruct the shipped ELF
loader to preload the actual ELF program image with the "runas.so" helper
library.
Fixes FS#909.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Commit 6f5f328003 removed freebsd.sh
because it was outdated and bad practice. Let's be consistent and remove
openbsd.sh as well.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The script will now detect uid/gid collision and can generate a table of
current allocation
./scripts/package-metadata.pl usergroup tmp/.packageinfo \
| sort -k 1,1r -k 3,3n \
| column -t
This should ensure that no collision will happen for each single build
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
libthread-db is a package that can be configured for external
toolchains, so let's have the script probe for it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The script can be used to quickly spin up QEMU virtual machines with lan
and wan network. Please read the initial part of the script for
instructions about how to configure host machine
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Without this change the code checked if the string was contained in the
feature option and not if the string matches the complete word. This only
removes the nand option from the omap24xx target, the other changes are
only removing options which were added twice.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
The feeds script sets value of TOPDIR in a way that is inconsistent
with how toplevel Makefile sets it. The inconsistency manifests when I
use a "build directory" with symlinks to LEDE source (see below).
When make is invoked in such a directory, make's TOPDIR variable is
set to that directory, whereas scripts/feeds sets TOPDIR to the top of
LEDE source, which results in creating feeds directory inside the LEDE
source instead of in the build directory.
This patch changes the script so that it reuses the TOPDIR value form
the environment if it exists. The result is that 'make
package/symlinks' correctly fetches feeds to the build directory
instead in the source.
I use the following commands to create the build directory:
ln -s $SRC/config config
ln -s $SRC/Config.in Config.in
ln -s $SRC/feeds.conf.default feeds.conf.default
ln -s $SRC/include include
ln -s $SRC/Makefile Makefile
mkdir package
ln -s $SRC/package/base-files package/base-files
ln -s $SRC/package/boot package/boot
ln -s $SRC/package/devel package/devel
ln -s $SRC/package/firmware package/firmware
ln -s $SRC/package/kernel package/kernel
ln -s $SRC/package/libs package/libs
ln -s $SRC/package/Makefile package/Makefile
ln -s $SRC/package/network package/network
ln -s $SRC/package/system package/system
ln -s $SRC/package/utils package/utils
ln -s $SRC/rules.mk rules.mk
ln -s $SRC/scripts scripts
ln -s $SRC/target target
ln -s $SRC/toolchain toolchain
ln -s $SRC/tools tools
This allows me to easily test changes in LEDE on multiple targets.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Implement a new flag "-f" for the feeds update command which causes the
script to fall back to a more agressive git update strategy in case there
are locally modified files in the feeds directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This can be used to tweak the buildbot behavior without having to change
buildbot's configuration.
It will also allow us to add more aggressive clean steps (e.g. on
toolchain changes), which would break developers' workflows if enable
by default.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add a fallback case to get_source_date_epoch.sh which reports the modification
time of the script itself in case there is no SCM information available, e.g.
when downloading .tar.gz or .zip tarballs produced by Github.
Also fix the mercurial case while we're at it.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The short git hash suffix printed by getver.sh is taken from the
latest local commit, change this to use the hash from latest
upstream commit if available. This is considered the intended
behavior based on commit message a642a11fac,
introducing getver.sh.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Conditional dependencies use the '(!cond) || dep' syntax, whereas
conditional select uses 'dep if cond'.
Add an extra check to suppress emitting a conditional if an equal
conditional select already exists.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rework the bundle-libraries.sh implementation to use a more robust approach
for executing host binaries through the shipped ELF loader and libraries.
The previous approach relied on symlinks pointing to a wrapper script which
caused various issues, especially with multicall binaries as the original
argv[0] name was not preserved through the ld.so invocation. Another down-
side was the fact that the actual binaries got moved into another directory
which caused executables to fail looking up resources with paths relative
to the executable location.
The new library wrapper implements the following improvements:
- Instead of symlinks pointing to a common wrapper, each ELF executable
is now replaced by a unqiue shell script which retains the original
program name getting called
- Instead of letting ld.so invoke the ELF executable directly, launch
the final ELF binary through a helper program which fixes up the argv[0]
argument for the target program
- Support sharing a common location for the bundled libraries instead of
having one copy in each directory containing wrapped binaries
Finally modify the SDK build to wrap the staging_dir and toolchain binaries
which allows to use the SDK on systems with a different glibc version.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This will be used to simplify the build system code for checking hashes.
Instead of using various variants of md5sum / openssl, use one simple
utility for all of them
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Because wget doesn't know how to do Negotiate authentication with a proxy
and curl does, use curl if it's present. The user is expected to have a
~/.curlrc that sets the options necessary for any proxy authentication.
A ~/.curlrc is completely optional however and curl will work in exactly
the same manner as wget without one.
Signed-off-by: Brian J. Murrell <brian@interlinx.bc.ca>
[Jo-Philipp Wich: Rework code to detect curl usability by checking --version,
Use vararg style open() to bypass the shell when downloading,
Use Text::ParseWords to decompose env vars into arguments]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The external script used to generate the package lists for the
LEDE wiki's table of packages [1] and package indexes [2] requires
a "Source:" field in the package lists to find package makefiles.
The package makefiles are used to read the package's Category and Submenu.
The "Source:" field was removed in commit
b4aa3c899c
to reduce package list sizes and lessen opkg issues in low ram devices.
Add a separate package list file with full data to be used by the wiki's script.
It's called Packages.manifest and isn't compressed as it's not necessary.
1. https://lede-project.org/packages/start
2. https://lede-project.org/packages/index/start
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
This will attempt to automatically fix common mistakes like using MD5
instead of SHA256, using the MD5SUM variable instead of HASH, or even a
missing mirror file hash.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In the build system, flock will prevent multiple concurrent downloads
for the same file. However, if one download request for the same file is
waiting for another one to finish, it will result in downloading the
same file twice consecutively.
Prevent this issue by exiting immediately if the file has already been
downloaded
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We have switched opkg to sha256 a long time ago, and shrinking package
lists is useful for systems that are running low on RAM
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Change getver.sh to append a short Git commit hash to the end of the artifical
revision number. This way we still have order- and comparable commit numbers
but also a direct relation to the Git commit.
The new output format will look like "r2400+2-882472e" for dirty trees or like
"r2402-882472e" for clean ones.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The SDK Makefile still trys to copy the docs folder which was removed
with 882f4d2d63. This causes an SDK build
error.
All other removals are just cleanup.
Signed-off-by: Mathias Kresin <dev@kresin.me>
If something goes wrong and script can't find upstream revision it will
return something like:
r2220
which looks like a valid upstream revision 2220. We cant' distinguish it
from e.g. 2200 upstream commits and 20 local ones.
The new format still provides revision number but also points clearly
that is may be not the upstream one:
r0+2220
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: John Crispin < john@phrozen.org>
So far we were displaying "local" which could be misinterpreted. It
wasn't possible e.g. to say if src-link feed was initialized or not.
Hopefully "X" makes (a bit) more sense.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's always hard to find a reasonable width that will make everyone
happy. This one at least makes "telephony" (one of default feeds) name
fit the column and hopefully isn't too big.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
So far, package-metadata.pl always considered the first provider of a virtual
package to be the default variant which might deviate from what buildroot
considers to be the default.
Change the Kconfig dependency / select code generation for virtual package
providers to consider the DEFAULT_VARIANT to be the primary provider and only
fall back to the first provider if no default variant was explicitely tagged.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Currently the code emitting dependencies for provide candidates is overwriting
the specification calculated by the previous conditional dependency handling
code, rendering dependencies on virtual PROVIDES packages in conjunction with
conditional dependencies unusable.
Instead of overwriting, append the PROVIDES dependency spec in order to fix
using DEPENDS on virtual provider packages in conjunction with conditions.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This is outdated and bad practice, general dependencies should be documented and leave the rest up to the user.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
When selecting devices from the Target Devices menu, the brand choices
of naming makes it confusing to find particular devices by name, as the
sorting is case sensitve. AirTight came after ALFA, and devolo and
jjPlus both came after Zyxel.
This does _not_ apply to the Target Profile list, as that includes
"Default - all profiles" inside the profile list.
Signed-off-by: Karl Palsson <karlp@etactica.com>
TARGET_MULTI_PROFILE and TARGET_PER_DEVICE_ROOTFS get some help text to
try and clarify their behaviour.
Signed-off-by: Karl Palsson <karlp@etactica.com>
If core packages are overridden, CONFIG_OVERRIDE_PKGS is set
based on the scan order of packages, which eventually causes
that config value to be modified on each build and with
that causes the build process to warn for configuration
being out of sync.
This commit changes the CONFIG_OVERRIDE_PKGS to be sorted
and prevents that false warning.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
