This update doesn't include:
3b1e0a7bdfee brcmfmac: add support for SAE authentication offload
be898fed355e brcmfmac: send port authorized event for FT-802.1X
due to nl80211 dependencies.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit c3aa33bf70)
This potentially fixes some issues seen on IBSS
when interfaces go out of range and then re-appear.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The skb_get_hash_perturb() function now takes a siphash_key_t instead of
an u32. This was changed in commit 55667441c84f ("net/flow_dissector:
switch to siphash"). Use the correct type in the fq header file
depending on the kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit eaa047179a)
The QCA953x only supports 25 MHz refclk, however some OEMs set an
invalid bootstrap value for the REF_CLK option, which would break the
clock detection in ath9k.
Force the QCA953x refclk to 25MHz in ath9k, as this is (according to the
datasheet) the only valid frequency.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4c6fe32468)
Import patches from upstream to sync 19.07 with master:
9f3e3323e996 rt2x00: allow to specify watchdog interval
2034afe4db4a rt2800: add helpers for reading dma done index
759c5b599cf4 rt2800: initial watchdog implementation
09db3b000619 rt2800: add pre_reset_hw callback
710e6cc1595e rt2800: do not nullify initialization vector data
e403fa31ed71 rt2x00: add restart hw
0f47aeeada2a rt2800: do not enable watchdog by default
41a531ffa4c5 rt2x00usb: fix rx queue hang
3b902fa811cf rt2x00usb: remove unnecessary rx flag checks
1dc244064c47 rt2x00: no need to check return value of debugfs_create functions
706f0182b1ad rt2800usb: Add new rt2800usb device PLANEX GW-USMicroN
95844124385e rt2x00: clear IV's on start to fix AP mode regression
567a9b766b47 rt2x00: do not set IEEE80211_TX_STAT_AMPDU_NO_BACK on tx status
14d5e14c8a6c rt2x00: clear up IV's on key removal
13fa451568ab Revert "rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band"
--pending-- rt2800: remove errornous duplicate condition
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Improves rate control responsiveness and performance
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[reworked to apply on 4.19.79 mac80211 + renumbered + refreshed]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This makes brcmfmac use the same wiphy after PCIe reset to help user
space handle corner cases (e.g. firmware crash).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit f39f4b2f6d)
Patch getting RAM info got upstreamed. A debugging fs entry for testing
reset feature was added.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 681acdcc54)
Close cooperation with Lorenzo Bianconi resulted
in these patches which fix all remaining seen issues
when using dynack.
Fix link losses when:
- Late Ack's are not seen or not present
- switching from too low static coverage class to dynack on a live link
These are fixed by setting the Ack Timeout/Slottime to
the max possible value for the currently used channel width when
a new station has been discovered.
When traffic flows, dynack is able to adjust to optimal values
within a few packets received (typically < 1 second)
These changes have been thoroughly tested on ~60 offshore devices
all interconnected using mesh over IBSS and dynack enabled on all.
Distances between devices varied from <100m up to ~35km
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
(cherry picked from commit f6e8ba0238fe349b7529357793e2fb18635819ed)
This updates to backports-4.19.57-1 which contains the wireless
subsystem and driver from kernel 4.19.57.
The removed patches are applied upstream.
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This doesn't include 9ff8614a3dbe ("brcmfmac: use separate Kconfig file
for brcmfmac") due to a few conflicts with backports changes.
An important change is:
[PATCH 2/7] brcmfmac: change the order of things in brcmf_detach()
which fixes a rmmod crash in the brcmf_txfinalize().
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit db8e08a5a4)
This improves FullMAC firmware compatibility, adds logging in case of
firmware crash and *may* fix "Invalid packet id" errors.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 8888cb725d)
FCC allows maximum antenna gain of 6 dBi. 15.247(b)(4):
> (4) The conducted output power limit
> specified in paragraph (b) of this section
> is based on the use of antennas
> with directional gains that do not exceed
> 6 dBi. Except as shown in paragraph
> (c) of this section, if transmitting
> antennas of directional gain greater
> than 6 dBi are used, the conducted
> output power from the intentional radiator
> shall be reduced below the stated
> values in paragraphs (b)(1), (b)(2),
> and (b)(3) of this section, as appropriate,
> by the amount in dB that the
> directional gain of the antenna exceeds
> 6 dBi.
https://www.gpo.gov/fdsys/pkg/CFR-2013-title47-vol1/pdf/CFR-2013-title47-vol1-sec15-247.pdf
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Most of the txpower for the ath10k firmware is stored as twicepower (0.5 dB
steps). This isn't the case for max_antenna_gain - which is still expected
by the firmware as dB.
The firmware is converting it from dB to the internal (twicepower)
representation when it calculates the limits of a channel. This can be seen
in tpc_stats when configuring "12" as max_antenna_gain. Instead of the
expected 12 (6 dB), the tpc_stats shows 24 (12 dB).
Tested on QCA9888 and IPQ4019 with firmware 10.4-3.5.3-00057.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
FCC allows maximum antenna gain of 6 dBi. 15.247(b)(4):
> (4) The conducted output power limit
> specified in paragraph (b) of this section
> is based on the use of antennas
> with directional gains that do not exceed
> 6 dBi. Except as shown in paragraph
> (c) of this section, if transmitting
> antennas of directional gain greater
> than 6 dBi are used, the conducted
> output power from the intentional radiator
> shall be reduced below the stated
> values in paragraphs (b)(1), (b)(2),
> and (b)(3) of this section, as appropriate,
> by the amount in dB that the
> directional gain of the antenna exceeds
> 6 dBi.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
struct ieee80211_local needs to be passed in separately instead of
dereferencing the (potentially NULL) sdata
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Replace the patch introduced by commit d0b969eee8 ("mac80211: rt2x00:
do not increment sequence number while re-transmitting") was merged
into wireless-drivers.git. Replace our version with the merged version.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The removed patches are now integrated in the upstream kernel.
Refresh all patches on top of the new backports release.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Imported from patchwork, patches marked with '=' have already been in
our tree:
[v3,1/4] cfg80211: add ratelimited variants of err and warn
[v3,2/4] rt2x00: use ratelimited variants dev_warn/dev_err
[v3,3/4] rt2x00: check number of EPROTO errors
=[v3,4/4] rt2x00: do not print error when queue is full
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently STA+AP re-transmitting the management frames with
incremented sequence number if hardware is assigning the sequence.
Fix is to assign the sequence number for Beacon by hardware
and for other Management frames software will assign the
sequence number
Signed-off-by: Vijayakumar Durai <vijayakumar.durai1@vivint.com>
consolidate patch 651-rt2x00-remove-unneccesary-code.patch.
fixup the most obvious whitespace problems in RXIQ and TX-LOFT code.
always backup registers bbpr1, bbpr4, bbpr241 and bbpr242 to avoid
compiler warning about them being potentially uninitialized.
no functional changes (intended)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
