Netgear R7800 switch LAN ports are numbered backwards in LuCI,
i.e. numbering is not corresponding to the actual physical port labels,
patch fixes that.
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
[merged with existing board using the same config]
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.
Specification:
- IPQ8064 (384 - 1,400 MHz)
- 512 MB of RAM
- 32 MB of Flash (SPI)
- 4T4R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 12x LEDs, 4x keys
- 1x USB 3.0 Type-A
- UART header on PCB
- RX, TX, NC, GND, Vcc from power connector side
- baudrate: 115200 bps
Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Connect power cable and turn on the router
3. When the "Press the [f] key and hit [enter] to enter failsafe mode"
message is displayed on the console, press the "f" key and Enter key
sequentially to enter the failsafe mode
4. create fw_env.config file with following contents on failsafe mode:
/dev/mtd9 0x0 0x10000 0x10000
5. Execute following commands to add and change the environment
variables of U-Boot
fw_setenv ipaddr "192.168.0.1"
fw_setenv serverip "192.168.0.2"
fw_setenv autostart "yes"
fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin;
bootipq"
6. Set the IP address of the computer to 192.168.0.2, connect to the LAN
port of WG2600HP, and start the TFTP server on the computer
7. Rename OpenWrt initramfs image for WG2600HP to
"wg2600hp-initramfs.bin" and place it in the TFTP directory
8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP
9. WG2600HP downloads initramfs image from TFTP server on the computer,
loads it and boot with initramfs image
10. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with the sysupgrade image
11. Wait ~180 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Hardware highlights:
- SoC: Qualcomm Atheros IPQ8064/5 ARM Dual Core CPU
- RAM: (512MB or 1GB) DDR3 System Memory
- Storage: 32MB NOR (Cypress S25FL256S1)
256MB NAND (Micron MT29F2G08ABBEAH4)
- Ethernet: 5 x 1G via QCA8337N
- USB: 1 x USB 2.0/3.0 + 1 x USB 2.0 on mini PCIe3 socket
- PCIe: 3x mini PCIe (third mini PCIE3 is PCIe/USB shared)
- SIM Card Slot: 2 x Slot
- Buttons: Reset Button
- LEDs: 18x, 8x GPIO controllable
- Buzzer
The correct amount of RAM will be passed by the bootloader.
In contrast to the documentation provided by Compex, the third PCIe
doesn't use GPIO16 for PERST. Instead, GPIO3 is shared and used as PERST
for PCIe0 and PCIe2.
So far, no one was able to get USB 3.0 working with the 1GB RAM version,
while it works fine for my 512MB version. Since USB 3.0 doesn't work with
the Compex firmware for the 1G variant either, it could be a hardware
issue with these boards.
OpenWrt will be installed to the NAND flash. Make sure to have a full
working image on the NOR flash. It will be the backup in case anything
goes wrong.
It has been observed that an image loaded via tftpboot might have
bitflips. Hence the extra step to create a crc32 checksum to allow to
compare the checksum with the one from the source file prior to flashing.
In all cases it is necessary to set the following u-boot parameter to an
empty (whitespace) value, to ensure that the chosen bootargs of the dts
isn't overwritten or set to bogus - not working - values:
(IPQ) # set bootargs " "
(IPQ) # set fsbootargs " "
(IPQ) # saveenv
The sysupgrade image can be installed directly on flash using u-boot (put
jumper in JP13 (leave JP9 open) to boot from nand):
(IPQ) # set serverip 192.168.1.20
(IPQ) # set ipaddr 192.168.1.1
(IPQ) # tftpboot 0x42000000 openwrt-ipq806x-compex_wpq864-squashfs-nand-factory.bin
(IPQ) # crc32 0x42000000 $filesize
(IPQ) # nand erase 0x1340000 0x4000000
(IPQ) # nand write 0x42000000 0x1340000 $filesize
The initramfs image can be started using:
(IPQ) # set fdt_high 0x48000000
(IPQ) # tftpboot 0x44000000 openwrt-ipq806x-compex_wpq864-initramfs-fit-uImage.itb
(IPQ) # bootm 0x44000000
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for GL.iNet GL-B1300
Specification:
- SOC: IPQ4028 / QCA Dakota
- RAM: 256 MiB
- FLASH: 32 MiB
- ETH: Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN)
- USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
- WLAN1: Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2
- WLAN2: Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2
- INPUT: one reset and one WPS button
- LEDS: 3 leds: Power, WIFI(only for 2.4G currently), and one reserved
- UART: 1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1
Installation:
Method 1:
- use serial port to stop uboot
- uboot command: run lf
Method 2:
- push down reset button and power on
- wait until three leds constantly on then release
- upgrade by uboot web at http://192.168.1.1
Note:
- the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method.
- the sysupgrade image can be automatically downloaded if tftp server at
192.168.1.2 have that file.
- the wifi led will be flashing when writing image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
This commit marks the CPUs switchport explicit as untagged.
Otherwise, an eth0.1 interface is created and the devices
LAN-ports are not working.
Signed-off-by: David Bauer <mail@david-bauer.net>
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
- 802.3af POE on Ethernet 1
- 18-24v passive POE (mode B) on Ethernet 2
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree
Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script
Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
This will allow to maintain the current syntax for LEDs config
when switching to a device tree compatible string boardname.
None of the current boards use a comma in the boardname, so they
will be unaffected.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Lantiq and IPQ806X (which includes IPQ40XX) both define the
same custom function {ipq806x|lantiq}_get_dt_led.
This patch moves the function into the base-file package at
lib/functions/leds.sh to make it more accessible for other
targets as well.
Cc: Mathias Kresin <dev@kresin.me>
Cc: John Crispin <john@phrozen.org>
Cc: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
AP-DK01.1-C1 is QCA dev board with:
- ipq4018 quad core ARM @716.8MHz, 2x2 dual (11n+11ac) radio
- 256MB RAM
- 32MB SPI flash
- QCA8075 multiport ethernet phy (WAN port, 4x LAN ports)
First installation via u-boot:
sf probe
sf erase 0x180000 0x1a00000
tftpboot 0x84000000 lede-ipq806x-AP-DK01.1-C1-squashfs-sysupgrade.bin
sf write 0x84000000 0x180000 $filesize
Further upgrades via sysupgrade.
Changes:
- add partitions
- set memory size to 256MB
- add reserved memory mapping
- add correct compatible string
- add image generation
- extract pre-cal data from ART partition
Compile and run tested.
Wirespeed NAT can be achieved with spreading rx interrupts over different
cores. Wifi speed is ~550Mbps @5GHz in open air.
Note:
AP-DK01.1-C1 is fully compatible with AP-DK01.2-C1, which has
ipq4028 instead of ipq4018 on board.
Changes since v2:
- based on dts(i) rework/cleanup submitted:
http://lists.infradead.org/pipermail/lede-dev/2017-October/009596.html
- precise reserved memory mapping
- more precise description
- compatible string
Signed-off-by: Roman Yeryomin <roman@advem.lv>
The ZyXEL NBG6817 calculates all MAC addresses based on the ethaddr
value stored in the U-Boot environment (0:APPSBLENV). No MAC addresses
are stored in the ART partition and the generated MAC addresses for the
wlan interfaces alternate randomly between 12:34:56:78:90:12 and
00:03:7f:12:34:56.
interface new/ OEM MAC old MAC
wlan-2.4g (phy1): ethaddr undefined
wlan-5g (phy0): ethaddr + 1 undefined
lan : ethaddr + 2 ethaddr
wan : ethaddr + 3 ethaddr + 1
This patch defines stable MAC addresses for the wlan interfaces for
the first time instead of generating them at random. The previously
defined values for lan/ wan are changed to follow the settings of the
OEM firmware.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The order of LAN ports shown in Luci is reversed compared to what is
written on the case of the device. Fix the order so that they match.
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
As of now OTP is being correctly parsed and the driver requires to parse pre-caldata to follow corresponding routine.
Rename cal file into pre-calfile so the board initialized correctly with API 2 board data (board-2.bin).
Also remove the now unneeded for qca9984 board.bin symlink to 5GHz calfile.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Do not assign the CPU port twice, this confuses LuCI and possible other
programs relying on topology information in board.json.
Ref: https://github.com/openwrt/luci/issues/1086
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch adds support for AVM FRITZ!Box 4040.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB Nanya NT5CC128M16IP
FLASH: 32 MiB MXIC MX25L25635FMI
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one WLAN and one WPS button
LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN.
Serial:
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1. The SoC's serial port is right
next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1"
header for it. Use a multimeter to figure out the pinout!
This board currently needs an additional u-boot image in order to boot
properly. Booting with EVA isn't possible ATM.
Install Procedure:
0. It's highly recommended to connect to the serial port.
The serial settings are listed above.
1. install a u-boot image for AVM Fritz!Box 4040
(see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and
<https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>)
2. upload the initramfs.itb image via tftp (u-boot listens to
192.168.1.1 - use binary transfer mode!)
3. connect to the FB4040 and use sysupgrade sysupgrade.bin
to install the image.
Works:
- Switch and Ethernet (99%)
- Buttons (WLAN, WPS)
- FLASH (1 x 32MiB NOR Chip)
- WLAN2G and WLAN5G
- CPUFREQ scaling
- PRNG
- serial
- Crypto Accelerator
- sysupgrade (Read the flash instructions to avoid bricking)
- full LEDE Install (Read the flash instructions to avoid bricking)
- LEDs (Power, WAN, Info (red and amber), LAN)
The LEDs are connected to the QCA8075 LED ports.
The AR40xx driver contains a gpio-controller to
handle these special "GPIOs".
- USB Both 3.0 and 2.0 ports
- many packages from other ARMv7 boards
(This does include the RaspberryPi Model 2!)
- ...
Not planned:
- WAN<->LAN short-cut
- Qualcomm Secure Execution Environment
- ...
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
After "73d923e base-files: emit tagged switch configuration by default"
some default network configurations are broken because the lan and wan
ifnames are forcibly set to untagged netdevs.
Adjust the offending set_interfaces_lan_wan() calls to use the proper
tagged device names.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Commit 71a39b8 ("ipq806x: Fix wireless support for Netgear Nighthawk X4S
D7800") added a trailing TAB char after the backslash which prevents
the assignment of the correct MACs for wifi devices.
Fixes: FS#451
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[reworded commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
D7800 has a simular hardware to R7800 and uses dual QCA9980 for both 2.4GHz and 5GHz band.
However there is no proper initialization for them, which causes a kernel panic due to failed firmware loading.
This patch adds d7800 to ath10k caldata extraction list.
I can get two functional wireless bands after making change to it.
Signed-off-by: Zhang Jingye <934526987@qq.com>
Remove the wifi5g LED from the the d7800, r7500 and r7800. Albeit this
GPIO is mentioned in the GPL tarball, it doesn't do anything. The
2.4/5 GHz LEDs are connected to the wifi chips and not be controlled
from the the userspace.
Use the LEDs names/colours as they are used in the board manuals. Merge
redundant LED configurations. Use the phy[0|1]tpt trigger for the
wireless LEDs. Remove the workarounds for the not controllable wireless
LEDs.
Fix spi compatible strings and remove superfluous spi-max-frequency
parameters.
If there are two power leds, use one for indicating normal operation and
one for failsafe/upgrade. Keep the on/off state of the main power led
during boot.
Use the usb pinmux settings from the nbg6817 gpl sources.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set the pinmux to the values found in the GPL tarballs of the boards.
Remove pinmux which are is not used (like nand pinmux for spi
flash boards).
This allows to use the wan orange led of the C2600 which had a wrong
pinmux before. Might fix buttons or leds of other boards as well.
Fix the LED color and the ledswitch key code of the C2600. Rename the
ledgnr to ledswitch.
Add support for indication the boot state using LEDs to the D7800,
NBG6817, R7500 and R7500v2.
Change GPIO active to readable values in D7800, EA8500, R7500,
R7500v2 and R7800.
Change gpioexport to gpio pinmux.
Add proper "drive strenght" to i2c4_pins and use it for RPM on
C2600, D7800, EA8500, R7500, R7500v2.
Remove pcie pinmux from D7800.
Move pinctrl to correct place in NBG6817 and R7800.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.
It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.
To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.
Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
Updating spi pins configuration in R7800 and C2600 DTs
Adding more usb power pin export and gsbi6 in R7800 DT
Updating and fixing leds
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CPU: 2x1.8GHz ARM, RAM: 512MiB
Storage: 4MiB serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports
WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO
For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin
to device. Then run:
cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4
cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5
reboot -f
For debugging serial console is easily visible on board, no soldering needed.
Signed-off-by: André Valentin <avalentin@marcant.net>
Signed-off-by: Alexis Green <alexis@cessp.it>
[Jo-Philipp Wich: add missing DEVICE_TITLE, fix model name in commit title]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Calibration data for QCA99x0 in this device has bogus macaddress.
The data cannot be modified directly, as it breaks checksum control.
Instead change the macaddress from phy add hotplug event.
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
Add support for the Netgear Nighthawk X4 R7500 and build
appropariate sysupgrade and factory images.
Known issues:
* 5 GHz wifi not working - there is no quantenna driver
* One of the USB ports is not working
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46796
DB149 is a IPQ8064 based platform. This patch adds the init scripts to
detect it, configure the network accordingly, and generate a flashable
image for it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45537
