Respect the generic kernel config setting, which is "enabled" tree-wide, as
previously done for sunxi.
Ref: 247ef4d98b ("sunxi: enable CONFIG_BPF_SYSCALL and CONFIG_EMBEDDED")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Fix the PLL register value for 10 Mbit/s link modes on TP-Link EAP
boards using a AR8033 SGMII PHY.
Otherwise, 10 Mbit/s links do not transfer data.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Tested-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
Fix the PLL register value for 10 Mbit/s link modes on the UniFi AC Lite
/ Mesh / LR. Otherwise, 10 Mbit/s links do not transfer data.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes incorrect supported link modes indicated when using ethtool
on the Ubiquiti UniFi AC lite / LR / Mesh.
eroot@OpenWrt:~# ethtool eth0
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 100baseT/Half 100baseT/Full
1000baseT/Full
1000baseX/Full
The reason for this is, that since kernel 5.4 the PHY capabilities are
read dynamically from the PHY. As Ubiquiti leaves the PHY in a wrong
state, the capabilities of the SGMII side of the PHY are read.
As a side effect, 10 Mbit/s link modes did not work on these boards.
Signed-off-by: David Bauer <mail@david-bauer.net>
From Frank Wunderlich <frank-w@public-files.de>:
Issue were traffic problems after a while with increased ping times if
flow offload is active.
It turns out that key_offset with cookie is needed in rhashtable_params
and head_offset was defined twice.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
DTS properties that match *-gpios are treated specially.
Use ngpios instead, as most GPIO drivers upstream do.
Fixes 5.10 DTS errors such as:
OF: /palmbus@300000/gpio@600: could not find phandle
Fixes DTC warnings such as:
Warning (gpios_property): /palmbus@300000/gpio@600:ralink,num-gpios:
Could not get phandle node for (cell 0)
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Use an existing kernel config symbol to fix devices whose ramstart is
not zero. See upstream patch message for more details.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Tobias Wolf <dev-NTEO@vplace.de>
Cc: Daniel Golle <daniel@makrotopia.org>
The mt7530_{r,w}32 operation over MDIO uses 3 mdiobus operations and
does not hold a lock, which causes a race condition when multiple
threads try to access a register, they may get unexpected results.
To avoid this, handle the MDIO lock manually, and use the unlocked
__mdiobus_{read,write} in the critical section.
This fixes the "Ghost VLAN" artifact[1] in MT7530/7621 when the VLAN
operation and the swconfig LED link status poll race between each other.
[1] https://forum.openwrt.org/t/mysterious-vlan-ids-on-mt7621-device/64495
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
CONFIG_MIPS_CMDLINE_FROM_DTB is set to 'y' for all ramips targets
already, which will ensure that the value of 'bootargs' will take
precedence over whatever is in arcs_cmdline.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Add "-i" option for reading & displaying firmware info. First it lists
in-firmware partitions ("fwup-ptn"). Then it checks for human
understandable partitions and prints data found in each of them.
This new feature is meant for development & debug purposes.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes partitioning on Linksys EA9500. With this change only the
currently used firmware MTD partition gets parsed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
CRYPTO_DEV_CCP depends on X86 or ARM64
CRYPTO_DEV_CCP_DD depends on CPU_SUP_AMD or ARM64
Compiling this driver makes sense for x86 mainly. If one day support for
ARM64 board with AMD Secure Processor gets added this package may be
updated.
Trying to build this package on bcm4908 was causing:
ERROR: module 'build_dir/target-aarch64_cortex-a53_musl/linux-bcm4908_generic/linux-5.4.110/drivers/crypto/ccp/ccp-crypto.ko' is missing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The old code didn't make sense as it was using "len" variable which was
guaranteed to be always 0. Loop right above broken code is:
while (len > 0) { }
With this recent ALIGN macro fix this resulted in subtracting block size
from 0 and calling write_out_padding() with a negative length.
To calculate amount of bytes needed for padding & alignment it should be
enough to use % 4.
Fixes: a2f6622945 ("firmware-utils: fix few random warnings")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes:
src/zyimage.c:10:0: warning: "_POSIX_SOURCE" redefined
src/zyimage.c:11:0: warning: "_POSIX_C_SOURCE" redefined
This change has been tested on Linux with -Wextra and on Mac OS.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Currently it's not possible to flash factory images on devices shipped
with vendor firmware versions 1.1.0 Build 20201120 rel. 50406 (published
2020-12-22):
(curFw_ver, newFw_ver) == (1.1, 1.0) [NM_Error](nm_checkSoftVer) 00848: Firmwave not supports, check failed.
[NM_Error](nm_checkUpdateContent) 01084: software version dismatched
[NM_Error](nm_buildUpgradeStruct) 01188: checkUpdateContent failed.
They've even following note in release notes:
Note: You will be unable to downgrade to the previous firmware version
after updating this firmware.
This version check in vendor firmware is implemented in
/usr/bin/nvrammanager binary likely as following C code[1]:
sscanf(buf, "%d.%d.%*s",&upd_fw_major, &upd_fw_minor);
...
if (((int)upd_fw_major < (int)cur_fw_major) ||
((ret = 1, cur_fw_major == upd_fw_major && (upd_fw_minor < (int)cur_fw_minor)))) {
ret = 0;
printf("[NM_Error](%s) %05d: Firmwave not supports, check failed.\r\n\r\n","nm_checkSoftVer" ,0x350);
}
...
return ret;
So in order to fix this and make it future proof it should be enough to
ship our factory firmware images with major version 7 (lucky number).
Tested on latest firmware version 1.1.2 Build 20210125 rel.37999:
Firmwave supports, check OK.
(curFw_ver, newFw_ver) == (1.1, 7.0) check firmware ok!
Flashing back to vendor firmware
c7v5_us-up-ver1-1-2-P1[20210125-rel37999]_2021-01-25_10.33.55.bin works
as well:
U-Boot 1.1.4-gbec22107-dirty (Nov 18 2020 - 18:19:12)
...
Firmware downloaded... filesize = 0xeeae77 fileaddr = 0x80060000.
Firmware Recovery file length : 15642231
Firmware process id 2.
handle_fw_cloud 146
Image verify OK!
Firmware file Verify ok!
product-info:product_name:Archer C7
product_ver:5.0.0
special_id:55530000
[Error]sysmgr_cfg_checkSupportList(): 1023 @ specialId 45550000 NOT Match.
Firmware supports, check OK.
Firmware Recovery check ok!
1. https://gist.github.com/ynezz/2e0583647d863386a66c3d231541b6d1
Signed-off-by: Petr Štetiar <ynezz@true.cz>
When adding the patch for the missing register, the patch file for the
testing kernel 5.10 was not included.
Fixes commit fbbad9a9a6 ("ath79: force SGMII SerDes
mode to MAC operation")
Signed-off-by: David Bauer <mail@david-bauer.net>
The mode on the SGMII SerDes on the QCA9563 is 1000 Base-X by default.
This only allows for 1000 Mbit/s links, however when used with an SGMII
PHY in 100 Mbit/s link mode, the link remains dead.
This strictly has nothing to do with the SerDes calibration, however it
is done at the same point in the QCA reference U-Boot which is the
blueprint for everything happening here. As the current state is more or
less a hack, this should be fine.
This fixes the issues outlined above on a TP-Link EAP-225 Outdoor.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Tested-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
For linux 5.10, kmod-ltq-deu need to be migrated to the new crypto
API/framework.
Leave it in tree for now and enable it only for Kernel 5.4. Maybe
someone picks up the work to migrate the package.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Following changes are made to the Lantiq kernel patches:
0001-MIPS-lantiq-add-pcie-driver.patch
The pci header isn't included by the of_pci header any longer
0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch
Due to the merge of grx390 and ar10 clocks, extend support to grx390
0025-NET-MIPS-lantiq-adds-xrx200-legacy.patch
The do_carrier arguments was dropped from phy_link_change. The
phylib has always sets the third parameter to true so the flag is
always changed anyway.
of_get_phy_mode() returns an error, or 0 on success, and pass a
pointer, of type phy_interface_t, where the phy mode should be
stored now. So far an error wasn't considered. Print at least an
error message if something unexpected happens.
The stuck queue is now passed to xrx200_tx_timeout (the timeout
handler) but not used so far.
0028-NET-lantiq-various-etop-fixes.patch
ioremap has provided non-cached semantics by default since the Linux
2.6 days and was removed with kernel version 5.6.
of_get_phy_mode() returns an error, or 0 on success, and pass a
pointer, of type phy_interface_t, where the phy mode should be
stored now. So far an error wasn't considered. Print at least an
error message if something unexpected happens.
0042-arch-mips-increase-io_space_limit.patch
Move IO space extension to laniq specific file
Signed-off-by: Mathias Kresin <dev@kresin.me>
Duplicate kernel 5.4 config and patches for kernel 5.10.
Duplicate the devicetree source files as well, they need kernel 5.10
specific adjustments.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the device_type property to mark PCI host bridges as such. With
linux 5.10 it is mandatory, otherwise the PCI IO space is flages as PCI
memory and the PCI init fails.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The callback handling of the tasklet API was redesigned and the macros
using the old syntax renamed to _OLD.
The stuck queue is now passed to ndo_tx_timeout callback but not used so
far.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to SCHED_FIFO being a broken scheduler model, all users of
sched_setscheduler() are converted to sched_set_fifo_low() upstream and
sched_setscheduler() is no longer exported.
The callback handling of the tasklet API was redesigned and the macros
using the old syntax renamed to _OLD.
Signed-off-by: Mathias Kresin <dev@kresin.me>
ltq tapi
ioremap has provided non-cached semantics by default since the Linux 2.6
days and was removed with kernel version 5.6.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Check if gendisk is already up instead of trying to figure out parent
mtd device (which didn't work well).
Reported-by: DENG Qingfang <dqfext@gmail.com>
Reported-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Fixes: 2809d00007 ("kernel: support FIT partition parser on mtdblock devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CPU: Allwinner V40 quad-core Cortex A7 @ 1.2GHz
Memory: 1GB DDR3
Storage: SDcard, native SATA
Network: 10/100/1000M ethernet, Ampak AP6212 wifi + BT
USB: 4x USB 2.0
Installation:
Use the standard sunxi installation to an SD-card.
While the board is very similar to the M2 Ultra board
(the V40 is the automotive version of the R40), as both
the u-boot and kernel supports them separately, and some
pins are different, let's add a separate device spec.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* check image checksums before writing to flash
* only bootmenu_0...9 are working, remove bootmenu_a entry
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In preparation for H6 support (which requires a separate ATF blob), add
an envvar to the A64 boards specifying which ATF blob to use.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
valgrind does not compile any more when using a GCC 10 for MIPS with
soft float. Just remove the parts which are generating assembler which
would not work.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Default to U-Boot env in UBI if root device is not mmc block device.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Some of bpi-r64 boards have serial NAND attached to SPI bus.
Add SD card image support for installing openwrt to it.
Default to nand upgrade if root device is not mmc block device.
Separate preloader and uboot images for snand are generated.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Some of bpi-r64 boards have serial NAND attached to SPI bus.
Build U-Boot for booting from SPI-NAND.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
The 100-ARM-dts-imx23-introduce-mmc0_sck_cfg.patch does
not need to be copied over as it's already merged upstream.
Other notable change is the USB_CHIPIDEA_OF change to
USB_CHIPIDEA_IMX [1].
[1] https://www.spinics.net/lists/linux-usb/msg193347.html
Compile/runtime-tested on Olinuxino Micro (imx23).
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Use generic functions to get env partition.
Fixes: 7043e4334f ("mediatek: mt7622: improve sysupgrade on MMC")
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
