Commit Graph

3808 Commits

Author SHA1 Message Date
Hauke Mehrtens
2d14da2c7d ar71xx: Fix mikrotik NAND compile problem
This fixes the following compile error:
drivers/mtd/nand/rb91x_nand.c: In function 'rb91x_nand_remove':
drivers/mtd/nand/rb91x_nand.c:445:16: error: 'rbni' undeclared (first use in this function)
  nand_release(&rbni->chip);

Fixes: 9cad70044f ("kernel: fix nand_release() usage.")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 66e04abbb6)
2020-07-07 23:43:26 +02:00
Hauke Mehrtens
673e7944bb ar71xx: Fix mikrotik NAND compile problem
There is one closing bracket too much.

Fixes: 9cad70044f ("kernel: fix nand_release() usage.")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 014d3f593a)
2020-07-06 00:12:04 +02:00
Hauke Mehrtens
9cad70044f kernel: fix nand_release() usage.
nand_release() takes nand_chip since commit 5bcfcbfc4019 ("mtd: rawnand:
Pass a nand_chip object to nand_release()")

Fixes: f4985a22ca ("kernel: Update kernel 4.14 to version 4.14.187")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-04 21:04:11 +02:00
Hauke Mehrtens
f4985a22ca kernel: Update kernel 4.14 to version 4.14.187
Fixes:
- CVE-2020-10757

Run tested: ath79, ipq40xx
Build tested: ath79, ipq40xx

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-04 19:22:23 +02:00
Lech Perczak
21454a772b ar71xx: fix reset key for TP-Link TL-WR802N V1/V2
During porting support for this router to ath79 target
it was discovered that GPIO mapping was incorrect (GPIO11 active high).
Correct mapping for both V1 and V2 is GPIO12 active low.

Default configuration from GPL source for V2 explicitly states this, and
this was confirmed experimentally on ath79 by looking on
/sys/kernel/debug/gpio. Correctness of this was also validated for V1 by
cross-flashing vendor firmware for V1 on V2 hardware, in which reset
button also worked.

Fix it.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit f841e70640)
2020-06-01 16:58:06 +02:00
David Bauer
9cafcbe0bd ar71xx: correct button type for TL-MR3020 mode slider
The TP-Link TL-MR3020 has a three-state mode slider which was previously
integrated as a button (EV_KEY). This led to spurious activations of
failsafe mode.

Set the type for the button to switch (EV_SW), to avoid unintended
activations of failsafe mode.

Related: commit 27f3f493de ("gpio-button-hotplug: unify polled and
interrupt code")

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b017a016cc)
2020-05-31 15:54:52 +02:00
Adrian Schmutzler
2bd1cf92e9 ar71xx: fix splitting firmware partition for TL-WR902AC v1
The -O option for the tplink-v1-header was missing for the TP-Link
TL-WR902AC v1, while safeloader and MTDPARTS where set up with a
single firmware partition.

This led to bootloops after using sysupgrade.

Fixes: FS#3118

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a7b07f8ba8)
2020-05-30 00:36:59 +02:00
Adrian Schmutzler
6ffd4d8a4d ar71xx: remove hard-coded folder name from Mikrotik RB upgrade
So far, specifying "BOARD_NAME := routerboard" is required by the
upgrade code of Mikrotik NAND devices, as "sysupgrade-routerboard"
is hardcoded in platform_do_upgrade_mikrotik_rb().

This patch replaces the latter with a grep for the name like it
is already done in nand_upgrade_tar() in /lib/upgrade/nand.sh.

This should enable upgrades from ar71xx to ath79 without setting
BOARD_NAME for the latter.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(backported from commit 281785d74f)
2020-05-12 17:48:02 +02:00
Thibaut VARÈNE
4cd44e5dc7 ar71xx: mikrotik: mach-rbspi.c remove wlan id
Following on the previous commit, this patch removes useless id argument
from rbspi_wlan_init().

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-12 12:43:38 +02:00
Thibaut VARÈNE
3fecb06fb1 ar71xx: mikrotik: bypass id check in __rb_get_wlan_data()
The id parameter in __rb_get_wlan_data() was incorrectly used on the
assumption that id "0" would always be tied to ath9k with RLE encoding
and positive id (in fact, only id "1" was valid) would always be tied to
("external") ath10k with LZO encoding.

Newer hardware revisions of supported devices prove this assumption to
be invalid, with ath9k caldata being now wrapped in MAGIC_ERD and LZO
compressed, so disable this check to allow newer hardware to correctly
decode caldata for ath9k. Since ath10k caldata is no longer pulled from
this implementation, this commit also disables the publication in sysfs
to avoid wasting memory.

Note: this patch assumes that ath9k caldata is never stored with the new
"LZOR" encoding scheme found on some ath10k devices.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-12 12:43:38 +02:00
Thibaut VARÈNE
b36aa168d8 ar71xx: mikrotik: ath10k: use new sysfs driver
Fetch ath10k calibration data from backported mikrotik sysfs driver
which supports the newer "LZOR" encoding.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-12 12:43:38 +02:00
Thibaut VARÈNE
612b64e6c4 ar71xx: enable mikrotik platform driver
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-12 12:43:38 +02:00
Petr Štetiar
f9ef0c5705 kernel: bump 4.14 to 4.14.178
Refreshed all patches and removed upstreamed:

 oxnas/001-irqchip-versatile-fpga-Handle-chained-IRQs-properly.patch
 oxnas/002-irqchip-versatile-fpga-Apply-clear-mask-earlier.patch

Fixes: CVE-2020-12114 and CVE-2020-11669

Runtime-tested on: qemu-x86-64
Compile-tested on: ath79/generic, x86/64, imx6

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-05-04 21:05:21 +02:00
Koen Vandeputte
0232f57e1a kernel: bump 4.14 to 4.14.176
Refreshed all patches.

Remove upstreamed:
- 0001-net-thunderx-workaround-BGX-TX-Underflow-issue.patch
- 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch
- 003-ARM-dts-oxnas-Fix-clear-mask-property.patch

Fixes:
- CVE-2020-8647
- CVE-2020-8648 (potentially)
- CVE-2020-8649

Compile-tested on: cns3xxx, octeontx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-04-16 13:23:52 +02:00
Baptiste Jonglez
f5b3cd1539 ar71xx: Fix gigabit switch support for Mikrotik RB951G-2HnD
Without this patch, when using rev 3 of the Atheros AR9344 SoC, the
gigabit switch (AR8327) does not work or works very erratically.

This is a re-spin of http://patchwork.ozlabs.org/patch/419857/ with a
different PLL value, according to the feedback from several users
(including myself) as shown here:

  https://openwrt.org/toh/mikrotik/rb2011uias#tracking_reported_experience_with_suggested_patch_for_the_5_gige_ports

Performance is acceptable: testing L3 forwarding without NAT yields a
performance of 370 Mbit/s (iperf3 TCP) and 41 Kpps (iperf3 UDP with 64
bytes payload). Both tests show that 100% of CPU time is spent on softirq.

A similar fix for a different device (RB2011) was added in e457d22261
("Make GBit switch work on RB2011").

Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
(cherry picked from commit 247043c968)
2020-03-28 13:46:26 +01:00
Jan Alexander
27e77922a1 ar71xx: use status led for GL.iNet GL-AR750S
Use power led for device status.

The status led behavior has already been fixed in af28d8a539
("ath79: add support for GL.iNet GL-AR750S") when porting the
device to ath79. This fixes it for ar71xx as well.

Signed-off-by: Jan Alexander <jan@nalx.net>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit d394c354ee)
2020-03-26 20:00:36 +01:00
Adrian Schmutzler
76c1c1daea ar71xx: fix port order on TP-Link Archer C60 v1/v2
The labels on the LAN ports of the TP-Link Archer C60 v1/v2 are
actually inverted compared to the ports of the internal switch.

Add this information to 02_network.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 14a07fa1f0)
2020-03-14 13:20:35 +01:00
Adrian Schmutzler
e4107e30a7 ar71xx: remove wrong MAC address adjustment for Archer C60 v2
The adjustment of the MAC address for Archer C60 v2 in 10_fix_wifi_mac
is broken since a "mac" partition is not set up for this device on
ar71xx. Instead, the MAC address is already patched correctly in
11-ath10k-caldata.

Remove the useless adjustment.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit cbdc919024)
2020-03-14 13:20:23 +01:00
Adrian Schmutzler
83f1015a6c ar71xx: fix swapped LAN/WAN MAC address for Archer C60 v1/v2
The MAC addresses for lan/wan are swapped compared to the vendor
firmware. This adjusts to vendor configuration, which is:

lan   *:7b   label
wan   *:7c   label+1
2.4g  *:7b   label
5g    *:7a   label-1

Only one address is stored in <&mac 0x8>, corresponding to the label.

This has been checked on revisions v1, v2 and v3.

Since ar71xx calculates the ath10k MAC address based on the ethernet
addresses, the number there is adjusted, too.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 14eb54938b)
2020-03-14 13:20:18 +01:00
Catrinel Catrinescu
68351990dc ar71xx/ath79: ew-dorin, fix the trigger level for WPS button
Because the WPS button had the wrong trigger level,
the failsafe mode was triggered quite often,
after this commit:
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=27f3f493de

Signed-off-by: Catrinel Catrinescu <cc@80211.de>
(cherry picked from commit 3e03b7ac4a)
2020-03-11 11:26:06 +01:00
David Bauer
1713707673 ar71xx: add missing LED migration for Archer C7
When changing the LED names for the Archer C7 to represent the correct
color, a migration for existing UCI entries was not created.

Add a migration to keep existing LED configurations working.

Fixes commit c79c001b59 ("ar71xx: Archer C7 v1 LED names and RFKILL
fixes")

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4349d4c682)
2020-03-01 23:46:13 +01:00
David Bauer
ef391799e3 ar71xx: correct AVM FRITZ Repeater 450E WPS button flag
The AVM FRITZ!WLAN Repeater 450E's WPS button is not active low.

Correct the active low flag to avoid unintenional activation of
failsafe mode on boot.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 1d4f2ca610)
2020-03-01 18:42:05 +01:00
Koen Vandeputte
af79c3bccc kernel: bump 4.14 to 4.14.171
Refreshed all patches.

Fixes:
- CVE-2013-1798

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-02-24 14:20:14 +01:00
Koen Vandeputte
1c5ac590c4 kernel: bump 4.14 to 4.14.167
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-01-24 13:17:32 +01:00
Kimmo Vuorinen
b6675c2b2e ar71xx: change u-boot-env to read-write for gl-ar150/-domino/mifi
Change u-boot-env partitions to be mounted as read-write for gl-ar150,
gl-domino and gl-mifi so uboot-envtools support is possible.

Signed-off-by: Kimmo Vuorinen <kimmo.vuorinen@gmail.com>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 2c1cfacdde)
2020-01-23 14:33:21 +01:00
Lech Perczak
1b4b4e3fae ar71xx: ubnt-rocket-m-ti: fix RSSI LED definitions
When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti Rocket M Titanium, it missed connection to actual interface.
Therefore create the mapping to interface, so RSSI LEDs work without
additional configuration, after starting rssileds service.

While at that, split RSSI into ~equal intervals for 6 LEDs,
and remove coefficients needed for PWM LEDs, as this board does not
support PWM LEDs.

Finally, for complete support, enable 'rssileds' package in per-device
rootfs, so the indicator works out of box.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 83708f233d)
2020-01-21 14:10:13 +01:00
Koen Vandeputte
9298c443df kernel: bump 4.14 to 4.14.164
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-01-20 13:43:56 +01:00
Thomas Nixon
67c8e586c8 ar71xx/mikrotik: use ath10k-ct-smallbuffers for 64 MiB devices
This image is only needed on one device (wAP AC); since this target is
going to be removed anyway it doesn't make sense to add an extra "low
RAM" image.

Fixes OOM issues on RouterBoard wAP AC.

Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
(cherry picked from commit 788c8485eb)
2020-01-18 00:31:37 +01:00
Hauke Mehrtens
330046922b kernel: bump 4.14 to 4.14.162
Refreshed all patches.

Compile-tested on: ipq40xx, ramips
Runtime-tested on: ipq40xx

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-01-04 23:04:24 +01:00
Koen Vandeputte
f80272dd9c kernel: bump 4.14 to 4.14.159
Refreshed all patches.

Remove upstreamed:
- 302-0002-dmaengine-dw-implement-per-channel-protection-contro.patch

Fixes:
- CVE-2019-19332

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-12-24 15:29:32 +01:00
Sungbo Eo
27eea24921 ar71xx: fix MAC address setup for TL-WDR4300 board
The current ethernet MAC address setup of TL-WDR4300 board is different
from the setup of stock firmware:

OpenWrt: lan = label_mac -2, wan = label_mac -2
  stock: lan = label_mac,    wan = label_mac +1

This patch applies to all devices using TL-WDR4300 board:
TL-WDR3600 v1
TL-WDR4300 v1
TL-WDR4300 v1 (IL)
TL-WDR4310 v1
Mercury MW4530R v1

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 9b02d32e34)
2019-12-21 00:31:39 +01:00
Koen Vandeputte
c3cc419cc6 kernel: bump 4.14 to 4.14.158
Refreshed all patches.

Altered patches:
- 400-mtd-add-rootfs-split-support.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-12-10 09:53:30 +01:00
Jo-Philipp Wich
eb836ea8e9 ar71xx: disable TP-Link TL-WA855RE by default
Disable the TP-Link TL-WA855RE image by default as the device has
insufficient flash space for release build images.

Ref: https://forum.openwrt.org/t/devices-too-big-to-save-overlay/18161/72
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-11-30 00:11:58 +01:00
Jo-Philipp Wich
7232d9247e ramips: disable TP-Link TL-WA750RE by default
Disable the TP-Link TL-WA750RE image by default as the device has
insufficient flash space for release build images.

Ref: https://forum.openwrt.org/t/devices-too-big-to-save-overlay/18161/30
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-11-30 00:05:46 +01:00
Jo-Philipp Wich
531ab59804 ar71xx: disable TP-Link TL-WA850RE by default
Disable the TP-Link TL-WA850RE image by default as the device has
insufficient flash space for release build images.

Ref: https://forum.openwrt.org/t/devices-too-big-to-save-overlay/18161/30
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-11-30 00:05:46 +01:00
Jo-Philipp Wich
0686418338 ar71xx: disable Netgear WNR2000v4 by default
Disable the Netgear WNR2000v4 image by default as the device has
insufficient flash space for release build images.

Ref: https://forum.openwrt.org/t/devices-too-big-to-save-overlay/18161/11
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-11-29 23:28:44 +01:00
Jo-Philipp Wich
6af348f6a1 ar71xx: disable On Networks N150R by default
Disable the On Networks N150R image by default as the device has
insufficient flash space for release build images.

Ref: https://forum.openwrt.org/t/devices-too-big-to-save-overlay/18161/10
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-11-29 23:28:44 +01:00
Jo-Philipp Wich
c65f09b641 ar71xx: disable TP-Link TL-WA850RE v2 by default
Disable the TP-Link TL-WA850RE v2 image by default as the device has
insufficient flash space for release build images.

Ref: https://forum.openwrt.org/t/devices-too-big-to-save-overlay/18161/9
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-11-29 23:28:44 +01:00
Jo-Philipp Wich
1793baee46 ar71xx: disable Netgear WNR612 v2 by default
Disable the Netgear WNR612 v2 image by default as the device has
insufficient flash space for release build images.

Ref: https://forum.openwrt.org/t/devices-too-big-to-save-overlay/18161/4
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-11-29 23:28:44 +01:00
Lech Perczak
3a5e28bd26 ar71xx: ubnt-(xm,xw): add rssileds package
In order to make RSSI indicator on the device work out of box,
include "rssileds" package in per-device rootfs image by default
for Ubiquiti XM and XW devices, namely:
- Bullet M (XM/XW)
- Rocket M (XM/XW)
- Nanostation M (XM/XW)
- Nanostation Loco-M (XW)

This moves the package addition to the individual devices in order
to prevent accidental inclusions of the package when not looking
at the parent node carefully enough.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[add bullet-m-xw, remove rocket-m-ti, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 08d9c95417)
2019-11-26 17:01:01 +01:00
Adrian Schmutzler
8fac0b398c ar71xx: fix buttons for TP-Link TL-WDR4900 v2
TP-Link TL-WDR4900 v2 only has one combined WPS/Reset button, so
don't set up an RFKILL for this device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 25127f58b4)
2019-11-21 12:29:54 +01:00
Adrian Schmutzler
3c65c47ce6 ar71xx: fix LED setup for TL-WDR4900 v2
In ar71xx there is only one combined mach file for Archer C5/C7 and
TL-WDR4900 v2. This one uses the same LED struct for all devices,
defining "green" LEDs for them. However, WDR4900 uses blue front
LEDs, while only C5/C7 uses green ones. Despite, in base-files
WDR4900 is actually set up with "blue" for the mentioned LEDs.

Thus, this patch creates a separate LED struct for WDR4900, so the
LEDs can be set up correctly. Despite, the wlan5g LED is removed as
it is controlled by ath9k chip for WDR4900 (in contrast to C5/C7).

Note: While front LEDs are blue, USB LEDs (on the back) are green,
so colors are mixed intentionally for the WDR4900 v2.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 93f2bcc35e)
2019-11-21 12:29:47 +01:00
Adrian Schmutzler
e945c43142 ar71xx: fix MAC address setup for TL-WDR4900 v2
The MAC address setup of the TL-WDR4900 v2 is different from the
C5/C7. This aligns ar71xx with the setup in ath79:

wlan0 (5GHz) : -2
wlan1 (2.4GHz) : -1
eth1 (LAN) : 0
eth0 (WAN) : 1

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a9d3084b83)
2019-11-21 12:29:28 +01:00
Adrian Schmutzler
8a21bc3622 ar71xx: fix MAC addresses for Archer C5 v1, C7 v1/v2, WDR4900 v2
As discussed in 1d18a14a90 ("ath79: really fix TP-Link Archer C7
v2 MAC address"), stock firmware MAC address assignment is
actually as follows:

wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1

This has never been fixed for ar71xx, so let's do it now.
Note that with WDR4900 v2 even both wlan0 and wlan1 where assigned
to basemac-1 before ...

Fixes: FS#408

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a021268032)
2019-11-21 12:29:20 +01:00
南浦月
3d840ee798 ar71xx: fix tl-wdr3320-v2 upgrade
Fix the error that tl-wdr3320-v2 can't upgrade firmware via web
interface by using magic_ver="0200" for this device.

Signed-off-by: 南浦月 <nanpuyue@gmail.com>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 0ff2385a92)
2019-11-12 16:16:00 +01:00
Adrian Schmutzler
b3514e3569 ar71xx: improve support for TP-Link CPE510 v2
This fixes commit bae927c551 ("ar71xx: add support for TP-LINK CPE510
V2.0") where the support for this device wasn't optimal.

Device support for the CPE510v2 so far has been a hack to enable
flashing with CPE510v1 images. Those even have different hardware (e.g.
additional ethernet port).

With this patch, we provide proper support for this device in ar71xx.

Installation:
- Flash factory image through stock firmware WEB UI or through TFTP
- To get to TFTP recovery just hold reset button while powering on
  for around 4-5 seconds and release.
- Rename factory image to recovery.bin
- Stock TFTP server IP: 192.168.0.100
- Stock device TFTP address: 192.168.0.254

Fixes: bae927c551 ("ar71xx: add support for TP-LINK CPE510 V2.0")
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[Rebased onto revert commit, changed comments in mach-cpe510.c,
changed commit title and description, fixed eth0 MAC address,
removed eth1 initialization]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[squashed revert, added fixes tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c79b796280)
[added CPE510V2 entry to tplink-safeloader.c]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 13:13:27 +01:00
Andreas Ziegler
b7ee43ecac ar71xx: add model detection for UniFi AC-LR
This commit adds correct model detection for UniFi
AC-LR. Previously, said device was incorrectly detected
as UniFi-AC-LITE/MESH.

The Information about the device is stored at 0xC in the EEPROM
partition. It corresponds to the sysid in /etc/board.info of the
Ubiquiti stock firmware.

Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
[adjust naming style of target to existing ones]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 2bc7c519dc)
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-27 18:13:33 +01:00
Koen Vandeputte
c4b514b200 kernel: bump 4.14 to 4.14.147
Refreshed all patches.

Altered patches:
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch (ar71xx)
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch (ath79)

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Compile-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-10-08 12:45:13 +02:00
Tomasz Maciej Nowak
6cdd518eb1 ar71xx: sysupgrade: accept ath79 combined-image
There is md5 sum of whole image embedded in combined-image header which
is checked on sysupgrade. The check will fail for ath79 images which
may have embedded metadata. This is because metadata are appended after
the combined image is created. To allow smooth transition from ar71xx to
ath79, strip metadata before calculating md5 sum for whole image.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
(cherry picked from commit 8b4109c2b4)
2019-09-29 11:30:50 +02:00
Koen Vandeputte
cd96cdaa60 kernel: bump 4.14 to 4.14.145
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-20 15:52:25 +02:00