The patch adds support for the TP-Link Archer A6 v3
The router is sold in US and India with FCC ID TE7A6V3
Specification
-------------
MediaTek MT7621 SOC
RAM: 128MB DDR3
SPI Flash: W25Q128 (16MB)
Ethernet: MT7530 5x 1000Base-T
WiFi 5GHz: Mediatek MT7613BE
WiFi 2.4GHz: Mediatek MT7603E
UART/Serial: 115200 8n1
Device Configuration & Serial Port Pins
---------------------------------------
ETH Ports: LAN4 LAN3 LAN2 LAN1 WAN
_______________________
| |
Serial Pins: | VCC GND TXD RXD |
|_____________________|
LEDs: Power Wifi2G Wifi5G LAN WAN
Build Output
------------
The build will generate following set of files
[1] openwrt-ramips-mt7621-tplink_archer-a6-v3-initramfs-kernel.bin
[2] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-factory.bin
[3] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-sysupgrade.bin
How to Use - Flashing from TP-Link Web Interface
------------------------------------------------
* Go to "Advanced/System Tools/Firmware Update".
* Click "Browse" and upload the OpenWrt factory image: factory.bin[2]
* Click the "Upgrade" button, and select "Yes" when prompted.
TFTP Booting
------------
Setup a TFTP boot server with address 192.168.0.5.
While starting U-boot press '4' key to stop autoboot.
Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin
From u-boot command prompt run tftpboot followed by bootm.
Recovery
--------
Archer A6 V3 has recovery page activated if SPI booting from flash fails.
Recovery page can be activated from serial console only.
Press 'x' while u-boot is starting
Note: TFTP boot can be activated only from u-boot serial console.
Device recovery address: 192.168.0.1
Thanks to: Frankis for Randmon MAC address fix.
Signed-off-by: Vinay Patil <post2vinay@gmail.com>
[remove superfluous factory image definition, whitespacing]
Signed-off-by: David Bauer <mail@david-bauer.net>
This adjusts the Makefile to use the new option to turn off the
doc builds. It will not cause any problems except a warning
about unused options if combined with a ccache source missing
the upstream patch.
Since a config setting is required to re-enable the doc build this
is equivalent to unconditionally disabling the docs if the config
setting is not created.
Signed-off-by: David Adair <djabhead@aol.com>
Prevent build error on Alpine Linux host:
libfakeroot.c error: conflicting types for 'id_t'
Error relocating openwrt/staging_dir/host/lib/libfakeroot.so: SEND_GET_XATTR: symbol not found
Signed-off-by: Ruslan Isaev <legale.legale@gmail.com>
The ZyXEL NR7101 prepend an additional header to U-Boot images. This
header use the TRX magic 0x30524448 (HDR0), but is incompatible with
TRX images.
This code is reverse-engineered based on matching 32 bit numbers
found in the header with lengths and different checksum
calculations of the vendor images found on the device. The result
was matched against the validation output produced by the
bootloader to name the associated header fields.
Example bootloader validation output:
Zyxel TRX Image 1 --> Found! Header Checksum OK
============ZyXEL header information==================
chipId : MT7621A
boardId : NR7101
modelId : 07 01 00 01
kernel_len : (14177560)
kernelChksum : (0x8DD31F69)
swVersionInt : 1.00(ABUV.0)D1
swVersionExt : 1.00(ABUV.0)D1
Zyxel TRX Image 2 --> Found! Header Checksum OK
============ZyXEL header information==================
chipId : MT7621A
boardId : NR7101
modelId : 07 01 00 01
kernel_len : (14176660)
kernelChksum : (0x951A7637)
swVersionInt : 1.00(ABUV.0)D0
swVersionExt : 1.00(ABUV.0)D0
=================================================
Check image validation:
Image1 Header Magic Number --> OK
Image2 Header Magic Number --> OK
Image1 Header Checksum --> OK
Image2 Header Checksum --> OK
Image1 Data Checksum --> OK
Image2 Data Checksum --> OK
Image1 Stable Flag --> Stable
Image1 Try Counter --> 0
Image1: OK
Image2: OK
The coverage and algorithm for the kernelChksum field is unknown.
This field is not validated by the bootloader or the OEM firmware
upgrade tool. It is therefore set to a static value for now.
The swVersion fields contain free form string values. The OEM firmware
use ZyXEL structured version numbers as shown above. The strings are
not interpreted or validated on boot, so they can be repurposed for
anything we want the bootloader to display to the user. But the OEM
web GUI fails to flash images with freeform strings.
The purpose of the other strings in the header is not known. The
values appear to be static. We assume they are fixed for now, until
we have other examples. One of these strings is the platform name,
which is taken as an input parameter for support other members of
the device family.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
The stock firmware does not accept firmware with "Talon" in the name.
Tested on firmware version 1.0.10 Build 20160902 rel. 57400 which came
preinstalled, as well as latest firmware version 2.0.1 Build 20170103
rel.71053 flashed from
AD7200v1-up-ver2-0-1-P1[20170103-rel71053]_2017-01-04_10.08.28.bin.
Fixes: 1a775a4fd0 ("ipq806x: add support for TP-Link Talon AD7200")
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
[added details about vendor firmware]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add "-i" option for reading & displaying firmware info. First it lists
in-firmware partitions ("fwup-ptn"). Then it checks for human
understandable partitions and prints data found in each of them.
This new feature is meant for development & debug purposes.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The old code didn't make sense as it was using "len" variable which was
guaranteed to be always 0. Loop right above broken code is:
while (len > 0) { }
With this recent ALIGN macro fix this resulted in subtracting block size
from 0 and calling write_out_padding() with a negative length.
To calculate amount of bytes needed for padding & alignment it should be
enough to use % 4.
Fixes: a2f6622945 ("firmware-utils: fix few random warnings")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes:
src/zyimage.c:10:0: warning: "_POSIX_SOURCE" redefined
src/zyimage.c:11:0: warning: "_POSIX_C_SOURCE" redefined
This change has been tested on Linux with -Wextra and on Mac OS.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Currently it's not possible to flash factory images on devices shipped
with vendor firmware versions 1.1.0 Build 20201120 rel. 50406 (published
2020-12-22):
(curFw_ver, newFw_ver) == (1.1, 1.0) [NM_Error](nm_checkSoftVer) 00848: Firmwave not supports, check failed.
[NM_Error](nm_checkUpdateContent) 01084: software version dismatched
[NM_Error](nm_buildUpgradeStruct) 01188: checkUpdateContent failed.
They've even following note in release notes:
Note: You will be unable to downgrade to the previous firmware version
after updating this firmware.
This version check in vendor firmware is implemented in
/usr/bin/nvrammanager binary likely as following C code[1]:
sscanf(buf, "%d.%d.%*s",&upd_fw_major, &upd_fw_minor);
...
if (((int)upd_fw_major < (int)cur_fw_major) ||
((ret = 1, cur_fw_major == upd_fw_major && (upd_fw_minor < (int)cur_fw_minor)))) {
ret = 0;
printf("[NM_Error](%s) %05d: Firmwave not supports, check failed.\r\n\r\n","nm_checkSoftVer" ,0x350);
}
...
return ret;
So in order to fix this and make it future proof it should be enough to
ship our factory firmware images with major version 7 (lucky number).
Tested on latest firmware version 1.1.2 Build 20210125 rel.37999:
Firmwave supports, check OK.
(curFw_ver, newFw_ver) == (1.1, 7.0) check firmware ok!
Flashing back to vendor firmware
c7v5_us-up-ver1-1-2-P1[20210125-rel37999]_2021-01-25_10.33.55.bin works
as well:
U-Boot 1.1.4-gbec22107-dirty (Nov 18 2020 - 18:19:12)
...
Firmware downloaded... filesize = 0xeeae77 fileaddr = 0x80060000.
Firmware Recovery file length : 15642231
Firmware process id 2.
handle_fw_cloud 146
Image verify OK!
Firmware file Verify ok!
product-info:product_name:Archer C7
product_ver:5.0.0
special_id:55530000
[Error]sysmgr_cfg_checkSupportList(): 1023 @ specialId 45550000 NOT Match.
Firmware supports, check OK.
Firmware Recovery check ok!
1. https://gist.github.com/ynezz/2e0583647d863386a66c3d231541b6d1
Signed-off-by: Petr Štetiar <ynezz@true.cz>
bcm4908img is a tool managing BCM4908 platform images. It's used for
creating them as well as checking, modifying and extracting data from.
It's required by both: host (for building firmware images) and target
(for sysupgrade purposes). Make it a host/target package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
JFFS2 bootfs partition in a BCM4908 image usually includes some padding.
For flashing it individually (writing to designed MTD partition) we want
just JFFS2 data.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's required for upgrading firmware using single partitions instead of
just blindly writing whole image.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's much easier to operate on BCM4908 image data with absolute offset
of each section stored. It doesn't require summing sizes over and over.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This adds support for accessing bootfs JFFS2 partition in the BCM4908
image. Support includes:
1. Listing files
2. Renaming file (requires unchanged name length)
Above commands are useful for flashing BCM4908 images which by defualt
come with cferom.000 file and require renaming it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's important for modifying / extracting firmware content. cferom is
optional image content at the file beginning.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
1. Don't allow pipe stdin as we need to fseek()
2. Don't alow TTY as it doesn't make sense for binary input
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Netgear uses CHK header which needs to be skipped when validating
BCM4908 image. Detect it directly in the bcm4908img tool. Dealing with
binary structs and endianess is way simpler in C.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Move code parsing existing firmware file to separated function. This
cleans up existing code and allows reusing parsing code for other
commands.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Update to the latest stable release.
This fixes a segfault and build failure seen compiling the 5.10 kernel
for x86/64. With this update, builds complete and sparse generates the
usual large volume of warnings as on 5.4 kernels.
Reported-by: Javier Marcet <javier@marcet.info>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This allows to specify an own magic instead of using the default magic
value TRX_MAGIC. If no own magic is specified the default one will be
used.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Discovered by coverty:
CID 1473630: Code maintainability issues (UNUSED_VALUE)
Assigning value from "type_to_guid_and_name(type, &name)" to
"part_guid" here, but that stored value is overwritten before it can
be used.
Remove the now redundant assignment of part_guid which is also set
conditionally later on.
Fixes: 4a078bd135 ("firmware-utils/ptgen: fix partition guid and name")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This old ELF library dating to 2009 used to be necessary on MacOS but
is not required for building the kernel or tools since [1]. On Linux
systems, libelf is already an OpenWRT build-system prerequisite [2].
Presence of the older library can mask or conflict with the system libelf
and lead to build errors, as seen compiling Linux kernels since v5.8 or
host tools such as dwarves (e.g. pahole).
Remove the unnecessary tools/libelf library and avoid the related issues.
[1] 5f8e587240 ("build: force disable stack validation during kernel build
on non-linux systems")
[2] https://openwrt.org/docs/guide-developer/build-system/install-buildsystem#prerequisites
Tested-by: Rosen Penev <rosenp@gmail.com> (Linux)
Tested-by: Georgi Valkov <gvalkov@abv.bg> (MacOS)
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add patches for mkimage to allow using it instead of the binary-only
'bromimage' tool to generate bl2 for MT7622.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Do not align partitions with sectors. Only kb align
for GPT is supported.
Use 254 heads and 63 sectors for PMBR.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Adding -H option copies partition to MBR after pmbr entry.
Max 3 partitions can be copied to MBR.
Hybrid MBR is needed only in special cases.
For example mt7622 SD card boot needs MBR entry with boot
flag enabled.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Don't download all of vim just to build xxd. Use a tight tarball
containing only xxd sources instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
U-Boot requires xxd to create the default environment from an external
file as done in uboot-mediatek.
Build xxd (only, not the rest of vim) as part of tools to make sure it
is present on the buildhost.
Reported-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow setting GPT partition names as used by TF-A bl2 to identify the
FIP volume to load from eMMC and SD-card.
While at it, also allow setting 'required' attribute as it should be
used for volumes which are essential for the system to boot.
Also properly handle setting the LEGACY_BOOT flag on the partition
selected as 'active', as this is how it is specified in the spec.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
mediatek-mt7622 as well as mediatek-mt7623 require CPIO to create their
initramfs images. So build CPIO as part of the host toolchain.
Signed-off-by: David Bauer <mail@david-bauer.net>
The TP-Link EAP235-Wall is a wall-mounted, PoE-powered AC1200 access
point with four gigabit ethernet ports.
When connecting to the device's serial port, it is strongly advised to
use an isolated UART adapter. This prevents linking different power
domains created by the PoE power supply, which may damage your devices.
The device's U-Boot supports saving modified environments with
`saveenv`. However, there is no u-boot-env partition, and saving
modifications will cause the partition table to be overwritten. This is
not an issue for running OpenWrt, but will prevent the vendor FW from
functioning properly.
Device specifications:
* SoC: MT7621DAT
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (MT7603EN): b/g/n, 2x2
* Wireless 5GHz (MT7613BEN): a/n/ac, 2x2
* Ethernet: 4× GbE
* Back side: ETH0, PoE PD port
* Bottom side: ETH1, ETH2, ETH3
* Single white device LED
* LED button, reset button (available for failsafe)
* PoE pass-through on port ETH3 (enabled with GPIO)
Datasheet of the flash chip specifies a maximum frequency of 33MHz, but
that didn't work. 20MHz gives no errors with reading (flash dump) or
writing (sysupgrade).
Device mac addresses:
Stock firmware uses the same MAC address for ethernet (on device label)
and 2.4GHz wireless. The 5GHz wireless address is incremented by one.
This address is stored in the 'info' ('default-mac') partition at an
offset of 8 bytes.
From OEM ifconfig:
eth a4:2b:b0:...:88
ra0 a4:2b:b0:...:88
rai0 a4:2b:b0:...:89
Flashing instructions:
* Enable SSH in the web interface, and SSH into the target device
* run `cliclientd stopcs`, this should return "success"
* upload the factory image via the web interface
Debricking:
U-boot can be interrupted during boot, serial console is 57600 baud, 8n1
This allows installing a sysupgrade image, or fixing the device in
another way.
* Access serial header from the side of the board, close to ETH3,
pin-out is (1:TX, 2:RX, 3:GND, 4:3.3V), with pin 1 closest to ETH3.
* Interrupt bootloader by holding '4' during boot, which drops the
bootloader into its shell
* Change default 'serverip' and 'ipaddr' variables (optional)
* Download initramfs with `tftpboot`, and boot image with `bootm`
# tftpboot 84000000 openwrt-initramfs.bin
# bootm
Revert to stock:
Using the tplink-safeloader utility from the firmware-utils package,
TP-Link's firmware image can be converted to an OpenWrt-compatible
sysupgrade image:
$ ./staging_dir/host/bin/tplink-safeloader -B EAP235-WALL-V1 \
-z EAP235-WALLv1_XXX_up_signed.bin -o eap235-sysupgrade.bin
This can then be flashed using the OpenWrt sysupgrade interface. The
image will appear to be incompatible and must be force flashed, without
keeping the current configuration.
Known issues:
- DFS support is incomplete (known issue with MT7613)
- MT7613 radio may stop responding when idling, reboot required.
This was an issue with the ddc75ff704 version of mt76, but appears to
have improved/disappeared with bc3963764d.
Error notice example:
[ 7099.554067] mt7615e 0000:02:00.0: Message 73 (seq 1) timeout
Hardware was kindly provided for porting by Stijn Segers.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
* The fit image is now created with 0666 permission in upstream U-Boot
remove our patch switch creates it with 0744
* The generated/autoconf.h file is created now as an empty file, it is
not needed to remove this include any more.
* Upstream lib/rsa/rsa-sign.c now includes stdlib.h instead of malloc.h
* ALIGN_MASK was moved to imagetool.h, own patch should not be needed
any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Multiple sources are hosted on OpenWrts source server only. The source
URLs to point to the server vary based on different epochs in OpenWrts
history.
Replace all by @OPENWRT which is an "empty" mirror, therefore using the
fallback servers sources.cdn.openwrt.org and sources.openwrt.org.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Although provided in separate zip archives, the firmwares for EU
and RU version are byte-identical. This adds the missing ID compared
to the support-list in the vendor firmware.
Note (since I checked it anyway):
Partitions and support list are unchanged for all three existing
firmware versions:
* 20200721-rel40773
* 20201029-rel43238
* 20201120-rel50399
Signed-off-by: Alexey Kunitskiy <alexey.kv@gmail.com>
[rewrite commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Switch to the normal tarball instead of the codeload generated one. The
latter has the potential to change hashes based on changes in the repo.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Asus looks for an extra data at the end of BCM4908 image, right before
the BCM4908 tail. It needs to be properly filled to make Asus accept
firmware image.
This tool constructs such a tail, writes it and updates CRC32 in BCM4908
tail accordingly.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Flashing image with BCM4908 CFE bootloader requires specific firmware
format. It needs 20 extra bytes with magic numbers and CRC32 appended.
This tools allows appending such a tail to the specified image and also
verifying CRC32 of existing BCM4908 image.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
BCM4908 CFE bootloader requires kernel to be prepended with a custom
header. This simple tool implements support for such headers.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It looks like GitHub changed the URL path for release tarballs, thus the
download for the zstd package was always falling back to the OpenWrt
sources mirror.
Fix the GitHub URL for one which works. The file hash remains unchanged.
Signed-off-by: David Bauer <mail@david-bauer.net>
Previously, ccache would end up using the system libzstd, which is not
supposed to be a build requirement.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
Instead of using an ancient qemu version in-tree the building machine
should just have qemu-utils installed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
cmake is a dependency of ccache, which means it is build before ccache
is available and hence must be build with non-ccache CC and CXX. It
currently works, because the cmake build system splits the compiler
variable and treats them as multiple compilers to check.
For "ccache gcc" it first tests for "ccache", which always fails,
because ccache is not a compiler by itself, even if it is available, and
then ends up calling "gcc" alone, effectively never using ccache.
Let's make this explicit by forcing the use of non-ccache CC and CXX.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
use PKG_FIXUP:=autoreconf to generate configure
200-hide-dlsym-error.patch deleted due to fixed upstream in another way
other patches refreshed to reflect latest changes
Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
Device hardware: https://deviwiki.com/wiki/TP-LINK_AD7200_(Talon)
The Talon AD7200 is basically an Archer C2600 with a third PCIe lane
and an 802.11ad radio. It looks like the Archers C2600/5400 but the
housing is slightly larger.
Specifications
--------------
- IPQ8064 dual-core 1400MHz
- QCA9988 2.4GHz WiFi
- QCA9990 5GHz WiFi
- QCA9500 60GHz WiFi
- 32MB SPI Flash
- 512MiB RAM
- 5 GBit Ports (QCA8337)
Installation
------------
Installation is possible from the OEM web interface.
Sysupgrade is possible.
TFTP recovery is possible.
- Image: AD7200_1.0_tp_recovery.bin
Notes
- This will be the first 802.11ad device supported by mainline.
Signed-off-by: Gary Cooper <gaco@bitmessage.de>
glibc started to return errors from dlerror() for dlsym() lookup failures which
results in a lot of messages from fakeroot like
dlsym(acl_get_fd): staging_dir/host/lib/libfakeroot.so: undefined symbol: acl_get_fd
dlsym(acl_get_file): staging_dir/host/lib/libfakeroot.so: undefined symbol: acl_get_file
dlsym(acl_set_fd): staging_dir/host/lib/libfakeroot.so: undefined symbol: acl_set_fd
when building OpenWrt using a recent glibc. Use the patch from the upstream
Debian package to silence these messages.
Link: https://bugs.debian.org/830912
Fixes: FS#3393
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Upstream switched to building with CMake. Adjust accordingly.
Reapplied patch as upstream changed the file format.
Added HOST_BUILD_PARALLEL for faster compilation.
Added cmake tool dependency and removed circular dependencies as a
result.
Adjusted dependent tools to use NOCACHE as they are needed to build
ccache.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This reverts commit b1952dc259 as it's
causing issues on the buildbot which uses some kind of ccache wrapper
and so the breakage needs to be investigated further:
bash: cmake: command not found
time: tools/ccache/compile#0.05#0.03#0.15
ERROR: tools/ccache failed to build.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Some Russian d-link routers require that their firmware be signed with a
salted md5 checksum followed by the bytes 0x00 0xc0 0xff 0xee. This tool
signs factory images the OEM's firmware accepts them.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
The Ubiquiti Network airCube AC is a cube shaped device supporting
2.4 GHz and 5 GHz with internal 2x2 MIMO antennas.
It can be powered with either one of:
- 24v power supply with 3.0mm x 1.0mm barrel plug
- 24v passive PoE on first LAN port
There are four 10/100/1000 Mbps ports (1 * WAN + 3 * LAN).
First LAN port have optional PoE passthrough to the WAN port.
SoC: Qualcomm / Atheros AR9342
RAM: 64 MB DDR2
Flash: 16 MB SPI NOR
Ethernet: 4x 10/100/1000 Mbps (1 WAN + 3 LAN)
LEDS: 1x via a SPI controller (not yet supported)
Buttons: 1x Reset
Serial: 1x (only RX and TX); 115200 baud, 8N1
Missing features:
- LED control is not supported
Physical to internal switch port mapping:
- physical port #1 (poe in) = switchport 2
- physical port #2 = switchport 3
- physical port #3 = switchport 5
- physical port #4 (wan/poe out) = switchport 4
Factory update is tested and is the same as for Ubiquiti AirCube ISP
hence the shared configuration between that devices.
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
Upstream switched to building with CMake. Adjust accordingly.
Reapplied patch as upstream changed the file format.
Added HOST_BUILD_PARALLEL for faster compilation.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This adds new strings for the v3.20 to the support list of the
already supported TP-Link CPE510 v3.
The underlying hardware appears to be the same, similar to the
situation with CPE210 v3.20 in 4a2380a1e7 ("tplink-safeloader:
expand support list for TP-Link CPE210 v3")
Signed-off-by: Gioacchino Mazzurco <gio@altermundi.net>
[extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Because some padding values in the TP-Link safeloader image generation
were hardcoded, different values were sometimes used throughout a
factory image. TP-Link's upgrade images use the same value everywhere,
so let's do the same here.
Although a lot of TP-Link's safeloader images have padded partition
payloads, images for the EAP-series of AC devices don't. This padding is
therefore also made optional.
By replacing the type of the padding value byte with a wider datatype,
new values outside of the previously valid range become available. Use
these new values to denote that padding should not be performed.
Because char might be signed, also replace the char literals by a
numeric literal. Otherwise '\xff' might be sign extended to 0xffff.
This results in factory images differing by 1 byte for:
* C2600
* ARCHER-C5-V2
* ARCHERC9
* TLWA850REV2
* TLWA855REV1
* TL-WPA8630P-V2-EU
* TL-WPA8630P-V2-INT
* TL-WPA8630P-V2.1-EU
* TLWR1043NDV4
* TL-WR902AC-V1
* TLWR942NV1
* RE200-V2
* RE200-V3
* RE220-V2
* RE305-V1
* RE350-V1
* RE350K-V1
* RE355
* RE450
* RE450-V2
* RE450-V3
* RE500-V1
* RE650-V1
The following factory images no longer have padding, shrinking the
factory images by a few bytes for:
* EAP225-OUTDOOR-V1
* EAP225-V3
* EAP225-WALL-V2
* EAP245-V1
* EAP245-V3
Signed-off-by: Sander Vanheule <sander@svanheule.net>
TP-Link safeloader firmware images contain a number of (small)
partitions with information about the device. These consist of:
* The data length as a 32-bit integer
* A 32-bit zero padding
* The partition data, with its length set in the first field
The OpenWrt factory image partitions that follow this structure are
soft-version, support-list, and extra-para. Refactor the code to put all
common logic into one allocation call, and let the rest of the data be
filled in by the original functions.
Due to the extra-para changes, this patch results in factory images that
change by 2 bytes (not counting the checksum) for three devices:
* ARCHER-A7-V5
* ARCHER-C7-V4
* ARCHER-C7-V5
These were the devices where the extra-para blob didn't match the common
format. The hardcoded data also didn't correspond to TP-Link's (recent)
upgrade images, which actually matches the meta-partition format.
A padding byte is also added to the extra-para partition for EAP245-V3.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
rules.mk always passes these as -I/-L to the toolchain.
Fixes rare errors like:
cc1: error: staging_dir/target-aarch64_cortex-a53_musl/usr/include: No such file or directory [-Werror=missing-include-dirs]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Paul Spooren <mail@aparcar.org>
Acked-by: Rosen Penev <rosenp@gmail.com>
Drop our local sstrip copy and use the current ELFKickers upstream
version.
Patch the original makefile in order to avoid building elftoc, since it
fails with musl's elf.h. This is fine, since we only need sstrip anyway.
Finally, add the possibility to pass additional arguments to sstrip and
pass -z (remove trailing zeros) by default, which matches the behaviour
of the previous version.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[shorten long commit msg lines]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Replace my o2.pl email address.
I'm still available at the old address.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link EAP225 v3 is an AC1350 (802.11ac Wave-2) ceiling mount access
point. Serial port access for debricking requires fine soldering.
Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MINO
* Ethernet (AR8033): 1× 1GbE, 802.3at PoE
Flashing instructions:
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J3 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R225 (TXD) and R237 (RXD).
Do NOT bridge R230.
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via LuCI web interface
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM boot log:
Using interface ath0 with hwaddr b0:...:3e and ssid "..."
Using interface ath10 with hwaddr b0:...:3f and ssid "..."
Tested by forum user blinkstar88
Signed-off-by: Sander Vanheule <sander@svanheule.net>
TP-Link EAP225-Outdoor v1 is an AC1200 (802.11ac Wave-2) pole or wall
mount access point. Debricking requires access to the serial port, which
is non-trivial.
Device specifications:
* SoC: QCA9563 @ 775MHz
* Memory: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 2x2
* Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO
* Ethernet (AR8033): 1× 1GbE, PoE
Flashing instructions:
* ssh into target device with recent (>= v1.6.0) firmware
* run `cliclientd stopcs` on target device
* upload factory image via web interface
Debricking:
To recover the device, you need access to the serial port. This requires
fine soldering to test points, or the use of probe pins.
* Open the case and solder wires to the test points: RXD, TXD and TPGND4
* Use a 3.3V UART, 115200 baud, 8n1
* Interrupt bootloader by holding ctrl+B during boot
* upload initramfs via built-in tftp client and perform sysupgrade
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From stock ifconfig:
ath0 Link encap:Ethernet HWaddr D8:...:2E
ath10 Link encap:Ethernet HWaddr D8:...:2F
br0 Link encap:Ethernet HWaddr D8:...:2E
eth0 Link encap:Ethernet HWaddr D8:...:2E
Tested by forum user PolynomialDivision on firmware v1.7.0.
UART access tested by forum user arinc9.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
TP-Link EAP245 v1 is an AC1750 (802.11ac Wave-1) ceiling mount access point.
Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9880): a/n/ac, 3x3
* Ethernet (AR8033): 1× 1GbE, 802.3at PoE
Flashing instructions:
* Upgrade the device to firmware v1.4.0 if necessary
* Exploit the user management page in the web interface to start telnetd
by changing the username to `;/usr/sbin/telnetd -l/bin/sh&`.
* Immediately change the malformed username back to something valid
(e.g. 'admin') to make ssh work again.
* Use the root shell via telnet to make /tmp world writeable (chmod 777)
* Extract /usr/bin/uclited from the device via ssh and apply the binary
patch listed below. The patch is required to prevent `uclited -u` in
the last step from crashing.
* Copy the patched uclited programme back to the device at /tmp/uclited
(via ssh)
* Upload the factory image to /tmp/upgrade.bin (via ssh)
* Run `chmod +x /tmp/uclited && /tmp/uclited -u` to install OpenWrt.
--- xxd uclited
+++ xxd uclited-patched
@@ -53796,7 +53796,7 @@
000d2240: 8c44 0000 0320 f809 0000 0000 8fbc 0010 .D... ..........
000d2250: 8fa6 0a4c 02c0 2821 8f82 87b8 0000 0000 ...L..(!........
-000d2260: 8c44 0000 0c13 45e0 27a7 0018 8fbc 0010 .D....E.'.......
+000d2260: 8c44 0000 2402 0000 0000 0000 8fbc 0010 .D..$...........
000d2270: 1040 001d 0000 1821 8f99 8374 3c04 0058 .@.....!...t<..X
000d2280: 3c05 0056 2484 a898 24a5 9a30 0320 f809 <..V$...$..0. ..
Debricking:
* Serial port can be soldered on PCB J3 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R225 (TXD) and R237 (RXD).
Do NOT bridge R230.
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via the LuCI web interface
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
Tested on the EAP245 v1 running the latest firmware (v1.4.0). The binary
patch might not apply to uclited from other firmware versions.
EAP245 v1 device support was originally developed and maintained by
Julien Dusser out-of-tree. This patch and "ath79: prepare for 1-port
TP-Link EAP2x5 devices" are based on that work.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Update mpc to 1.2.1
http://www.multiprecision.org/mpc/
Bug fixes:
Fix an incompatibility problem with GMP 6.0 and before.
Fix an intermediate overflow in asin.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
this patch fixes/improves follows:
- PATTERN_LEN is defined as a macro but unused
- redundant logic in count-up for "ptn"
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Due to the use of LD_LIBRARY_PATH, the programs running in the fakeroot
environment may end up loading bundled SDK libraries using the system
ld.so.
Rework the relocatability patch to avoid meddling with LD_LIBRARY_PATH
and construct the paths to faked and libfakeroot.so directly.
Fixes: f93cb5c2c8 ("fakeroot: make fakeroot script relocatable")
Reviewed-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Patch the fakeroot script template to discover faked and libfakeroot.so
relative to the STAGING_DIR_HOST environment variable, similar to how it
is done for automake, libtool, quilt and autoconf already.
This avoids the need for passing the paths to faked and libfakeroot.so
manually every time we invoke fakeroot and subsequently allows us to
drop OS X specific logic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
TP-Link RE200 v4 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas.
It's based on MediaTek MT7628AN+MT7610EN like the v2/v3.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button
- UART connection holes on PCB (57600 8n1)
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
The MAC address assignment matches stock firmware, i.e.:
LAN : *:8E
2.4G: *:8D
5G : *:8C
MAC address assignment has been done according to the RE200 v2.
The label MAC address matches the OpenWrt ethernet address.
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Recovery
--------
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.
Instructions for serial console and recovery may be checked out in
commit 6d6f36ae78 ("ramips: add support for TP-Link RE200 v2") or on
the device's Wiki page.
Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[removed empty line, fix commit message formatting]
Signed-off-by: David Bauer <mail@david-bauer.net>
Since we have a v2.1 (EU) with different partitioning now, rename
the v2.0 to make the difference visible to the user more directly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the TP-Link TL-WPA8630P (EU) in its v2.1
version. The only unique aspect for the firmware compared to v2
layout is the partition layout.
Note that while the EU version has different partitioning for
v2.0 and v2.1, the v2.1 (AU) is supported by the v2-int image.
If you plan to use this device, make sure you have a look at
the Wiki page to check whether the device is supported and
which image needs to be taken.
Specifications
--------------
- QCA9563 750MHz, 2.4GHz WiFi
- QCA9888 5GHz WiFi
- 8MiB SPI Flash
- 128MiB RAM
- 3 GBit Ports (QCA8337)
- PLC (QCA7550)
Installation
------------
Installation is possible from the OEM web interface. Make sure to
install the latest OEM firmware first, so that the PLC firmware is
at the latest version. However, please also check the Wiki page
for hints according to altered partitioning between OEM firmware
revisions.
Notes
-----
The OEM firmware has 0x620000 to 0x680000 unassigned, so we leave
this empty as well. It is complicated enough already ...
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
[improve partitions, use v2 DTSI, add entry in 02_network, rewrite
and extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
libressl update to 3.2.1
Delete 001-dont-build-tests-man.patch
Add configure args :
--enable-static
--disable-tests
The patch (001-dont-build-tests-man.patch) no longer works with the current version.
Follow the patch notes:
Adding the --enable-static and --disable-tests parameters should replace the patch.
Signed-off-by: Yuan Tao <ty@wevs.org>
TP-Link EAP225-Wall v2 is an AC1200 (802.11ac Wave-2) wall plate access
point. UART access and debricking require fine soldering.
The device was kindly provided for porting by Stijn Segers.
Device specifications:
* SoC: QCA9561 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (GD25Q127CSIG)
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (SoC): 4× 100Mbps
* Eth0 (back): 802.3af/at PoE in
* Eth1, Eth2 (bottom)
* Eth3 (bottom): PoE out (can be toggled by GPIO)
* One status LED
* Two buttons (both work as failsafe)
* LED button, implemented as KEY_BRIGHTNESS_TOGGLE
* Reset button
Flashing instructions, requires recent firmware (tested on 1.20.0):
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R162 (TXD) and R165 (RXD)
Do NOT bridge R164
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via sysupgrade or LuCI web interface
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM ifconfig:
br0 Link encap:Ethernet HWaddr 50:...:04
eth0 Link encap:Ethernet HWaddr 50:...:04
wifi0 Link encap:UNSPEC HWaddr 50-...-04-...
wifi1 Link encap:UNSPEC HWaddr 50-...-05-...
Signed-off-by: Sander Vanheule <sander@svanheule.net>
[fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link EAP245 v3 is an AC1750 (802.11ac Wave-2) ceiling mount access
point. UART access (for debricking) requires non-trivial soldering.
Specifications:
* SoC: QCA9563 (CPU/DDR/AHB @ 775/650/258 MHz)
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 3x3
* Wireless 5GHz (QCA9982): a/n/ac 3x3 with MU-MIMO
* Ethernet (QCA8337N switch): 2× 1GbE, ETH1 (802.3at PoE) and ETH2
* Green and amber status LEDs
* Reset switch (GPIO, available for failsafe)
Flashing instructions:
All recent firmware versions (latest is 2.20.0), can disable firmware
signature verification and use a padded firmware file to flash OpenWrt:
* ssh into target device and run `cliclientd stopcs`
* upload factory image via web interface
The stopcs-method is supported from firmware version 2.3.0. Earlier
versions need to be upgraded to a newer stock version before flashing
OpenWrt.
Factory images for these devices are RSA signed by TP-Link. While the
signature verification can be disabled, the factory image still needs to
have a (fake) 1024 bit signature added to pass file checks.
Debricking instructions:
You can recover using u-boot via the serial port:
* Serial port is available from J3 (1:TX, 2:RX, 3:GND, 4:3.3V)
* Bridge R237 to connect RX, located next to J3
* Bridge R225 to connect TX, located inside can on back-side of board
* Serial port is 115200 baud, 8n1, interrupt u-boot by holding ctrl+B
* Upload initramfs with tftp and upgrade via OpenWrt
Device mac addresses:
Stock firmware has the same mac address for 2.4GHz wireless and
ethernet, 5GHz is incremented by one. The base mac address is stored in
the 'default-mac' partition (offset 0x90000) at an offset of 8 bytes.
ART blobs contain no mac addresses.
From OEM ifconfig:
ath0 Link encap:Ethernet HWaddr 74:..:E2
ath10 Link encap:Ethernet HWaddr 74:..:E3
br0 Link encap:Ethernet HWaddr 74:..:E2
eth0 Link encap:Ethernet HWaddr 74:..:E2
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
TP-Link has introduced a compatibility level to prevent certain
downgrades. This information is stored in the soft-version partition,
changing the data length from 0xc to 0x10.
The compatibility level doesn't change frequently. For example, it has
the following values for the EAP245v3 (released 2018-Q4):
* FW v2.2.0 (2019-05-30): compat_level=0
* FW v2.3.0 (2019-07-31): compat_level=0
* FW v2.3.1 (2019-10-29): compat_level=1
* FW v2.20.0 (2020-04-23): compat_level=1
Empty flash values (0xffffffff) are interpreted as compat_level=0.
If a firmware upgrade file has a soft-version block without
compatibility level (data length < 0x10), this is also interpreted as
compat_level=0.
By including a high enough compatibility level in factory images, stock
firmware can be convinced to accept the image. A compatibility level
aware firmware will keep the original value.
Example upgrade log of TP-Link EAP245v3 FWv2.3.0 to FWv2.20.0:
[NM_Debug](nm_fwup_verifyFwupFile) 02073: curSoftVer:2.3.0 Build
20190731 Rel. 51932,newSoftVer:2.20.0 Build 20200423 Rel. 36779
...
AddiHardwareVer check: NEW(0x1) >= CUR(0x0), Success.
...
[NM_NOTICE](updateDataToNvram) 00575: Restore old additionalHardVer:
0x0.(new 0x1)
[NM_NOTICE](updateDataToNvram) 00607: PTN 07: name = soft-version,
base = 0x00092000, size = 0x00000100 Bytes, upDataType = 1,
upDataStart = 7690604b, upDataLen = 00000018
[NM_Debug](updateDataToNvram) 00738: PTN 07: write bytes = 000002eb
Other firmware upgrades have been observed to modify the compabitility
stored level (e.g. TP-Link EAP225-Outdoor FWv1.4.1 to FWv1.7.0).
Therefore, it seems to be the safest option to set the OpenWrt
compatibility level to the highest known value instead of the highest
possible value (0xfffffffe), to ensure users do not get unexpectedly
refused firmware upgrades when using a device reverted back to stock.
To remain compatible with existing devices and not produce different
images, the image builder doesn't store a compatibility level if it is
zero.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The soft-version partition actually contains a header and trailing data:
* header: {data length, [zero]}
* data: {version, bcd encoded date, revision}
The data length is currently treated as a magic number, but should
contain the length of the partition data.
This header is also present the following partitions (non-exhaustive):
* string-based soft-version
* support-list
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Some environments, e.g. first gen WSL, do not support SysV IPC.
Enforce the use of TCP transport instead which should be universally
available.
Fixes: FS#3317
Ref: https://github.com/microsoft/WSL/issues/4067
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This target is still on kernel 4.14, and recent attempts to move it to
kernel 5.4 have not led to success. The device tester reported that it
wouldn't boot with the following messages:
From sysupgrade:
Press any key within 4 seconds to enter setup....
loading kernel from nand... OK
setting up elf image... OK
jumping to kernel code
At this point the system hangs.
From CompactFlash:
Press any key within 4 seconds to enter setup....
Booting CF
Loading kernel... done
setting up elf image... kernel out of range kernel loading failed
The tester reported that the same was observed with current master
(kernel 4.14) as well. This looks like some kernel size restriction.
Since this target is quite old and only supports one device, and since
nobody else seemed interested in working on this for quite some time,
I decided to not put further work into analyzing the problem and drop
this together with the other 4.14-only targets.
Patchwork series:
https://patchwork.ozlabs.org/project/openwrt/list/?series=197066&state=*
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This sorts the added tools and builddir dependencies alphabetically
to make it easier to find something in the Makefile.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
These tools have been used by the orion target which has been
removed in Jan 2020 [1].
Both were specifically meant for the WRT350Nv2, which is not
supported anymore.
So, let's remove them as well.
[1] 89f2deb372 ("orion: remove unmaintained target")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Instead of using http and https for source downloads from
downloads.openwrt.org, always use https for it's better security.
Signed-off-by: Paul Spooren <mail@aparcar.org>
SELinux uses extended attributes to store SELinux security contexts.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[rebase, add commit message]
Signed-off-by: W. Michael Petullo <mike@flyn.org>
lzma-old host package is required for building ath79 images, as
mksquashfs-lzma is required for generating netgear images.
Fixes commit 4e4ee46495 ("ar71xx: drop target")
Signed-off-by: David Bauer <mail@david-bauer.net>
The kernel has become too big again for the ar9344-based TP-Link
CPE/WBS devices which still have no firmware-partition splitter.
Current buildbots produce a kernel size of about 2469 kiB, while
the partition is only 2048 kiB (0x200000). Therefore, increase it
to 0x300000 to provide enough room for this and, hopefully, the
next kernel.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target has been mostly replaced by ath79 and won't be included
in the upcoming release anymore. Finally put it to rest.
This also removes all references in packages, tools, etc. as well as
the uboot-ar71xx and vsc73x5-ucode packages.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The release notes says this:
As already said, the changes since 2.1.1 are primarily bug fixes, addressing
compiler warnings and issues reported by diagnostic tools, but also build
failures for some configurations.
https://lists.infradead.org/pipermail/linux-mtd/2020-July/081299.html
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
TP-LINK published a firmware update for the archer c6 v2.
This updates also reached the factory devices. Newer software version
rejects downgrading to 1.2.x. Use 1.9.x to allow installing the factory images
and have a little bit time to change it again.
Tested on archer c6 v2 with firmware 1.3.1
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The TL-WPA8630P v2 is a HomePlug AV2 compatible device with a QCA9563 SoC
and 2.4GHz and 5GHz WiFi modules.
Specifications
--------------
- QCA9563 750MHz, 2.4GHz WiFi
- QCA9888 5GHz WiFi
- 8MiB SPI Flash
- 128MiB RAM
- 3 GBit Ports (QCA8337)
- PLC (QCA7550)
MAC address assignment
----------------------
WiFi 2.4GHz and LAN share the same MAC address as printed on the label.
5GHz WiFi uses LAN-1, based on assumptions from similar devices.
LAN Port assignment
-------------------
While there are 3 physical LAN ports on the device, there will be 4
visible ports in OpenWrt. The fourth port (internal port 5) is used
by the PowerLine Communication SoC and thus treated like a regular
LAN port.
Versions
--------
Note that both TL-WPA8630 and TL-WPA8630P, as well as the different
country-versions, differ in partitioning, and therefore shouldn't be
cross-flashed.
This adds support for the two known partitioning variants of the
TL-WPA8630P, where the variants can be safely distinguished via the
tplink-safeloader SupportList. For the non-P variants (TL-WPA8630),
at least two additional partitioning schemes exist, and the same
SupportList entry can have different partitioning.
Thus, we don't support those officially (yet).
Also note that the P version for Germany (DE) requires the international
image version, but is properly protected by SupportList.
In any case, please check the OpenWrt Wiki pages for the device
before flashing anything!
Installation
------------
Installation is possible from the OEM web interface. Make sure to
install the latest OEM firmware first, so that the PLC firmware is
at the latest version. However, please also check the Wiki page
for hints according to altered partitioning between OEM firmware
revisions.
Additional thanks to Jon Davies and Joe Mullally for bringing
order into the partitioning mess.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
[minor DTS adjustments, add label-mac-device, drop chosen, move
common partitions to DTSI, rename de to int, add AU support strings,
adjust TPLINK_BOARD_ID, create common node in generic-tp-link.mk,
adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
SELinux support requires setting the appropriate SELinux security context
to files and directories, which needs to happen at build time in order
to support read-only root filesystem scenarios. In order to create these
security contexts, we will have to run some SELinux-specific tools on
the host machine, but that requires root access. This adds support for
fakeroot, which the build process will use to run the SELinux security
context creation and the image creation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Apply to current master, and adjust commit message
Thomas' original work is available at
http://lists.infradead.org/pipermail/openwrt-devel/2019-November/025976.html.
Signed-off-by: W. Michael Petullo <mike@flyn.org>
[add rules.mk FAKEROOT variable]
Signed-off-by: Paul Spooren <mail@aparcar.org>
[update, fix macos build]
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The variable in the case argument was mistyped, so the case always
checked against an empty string and never matched.
Fix the variable name. Add a PKG_RELEASE to Makefile so we can bump it.
Fixes: d6de31310c ("cmake: restore parallel build support for bootstrap")
Signed-off-by: Piotr Stefaniak <pstef@freebsd.org>
[add commit message, add PKG_RELEASE, fix commit title, add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit 685570858d.
The commit had several formal flaws, revert it and hopefully apply
it properly next time.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The variable in the case argument was mistyped, so the case always
checked against an empty string and never matched.
Fix the variable name.
Signed-off-by: Piotr Stefaniak <pstef@freebsd.org>
[add commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
By using localtime() to determine the timestamp that goes into factory
images, the resulting image depends on the timezone of the build system.
Use gmtime() instead, which results in more reproducible images.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
TP-Link RE200 v3 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN like the v2.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button
Unverified:
- UART header on PCB (57600 8n1)
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
MAC address assignment has been done according to the RE200 v2.
The label MAC address matches the OpenWrt ethernet address.
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Recovery
--------
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.
The device has not been opened for adding support. However, it is expected
that the behavior is similar to the RE200 v2. Instructions for serial console
and recovery may be checked out in commit 6d6f36ae78 ("ramips: add support
for TP-Link RE200 v2") or on the device's Wiki page.
Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[adjust commit title/message, sort support list]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For the TP-Link 4M devices with tplink-v2-image recipe
(mktplinkfw2.c), there are two different flash layouts based
on the size of the (u)boot partition:
device uboot OEM firmware OpenWrt (incl. config)
tl-wr840n-v5 0x20000 0x3c0000 0x3d0000
tl-wr841n-v14 0x10000 0x3d0000 0x3e0000
In both cases, the 0x10000 config partition is used for the firmware
partition as well due to the limited space available and since it's
recreated by the OEM firmware anyway.
However, the TFTP flashing process will only copy data up to the
size of the initial (OEM) firmware size. Therefore, while we can
use the bigger partition to have additional erase blocks on the
device, we have to limit the image sizes to the TFTP limits.
So far, only one layout definition has been set up in mktplinkfw2.c
for 4M mediatek devices. This adds a second one and assigns them
to the devices so the image sizes are correctly restrained.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The stored source code of flock contains the version string of version
2.18, reflect that in the Makefile.
Motivation is the tracking of changes in the buildsystem, which requires
versioning of packages.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Comparing the in tree stored source file of sstrip suggests it's version
2.0[0], reflect that in the Makefile.
Motivation is the tracking of changes in the buildsystem, which requires
versioning of packages.
[0]: df4426a0f0 (diff-d3ba694d91432a068d5d3b36abf8cd0f)
Signed-off-by: Paul Spooren <mail@aparcar.org>
There is no versioning information in the firmware-utils code nor the
Makefile. Consider it as first release by adding PKG_RELEASE.
Motivation is the tracking of changes in the buildsystem, which requires
versioning of packages.
Also update copyright.
Signed-off-by: Paul Spooren <mail@aparcar.org>
There is no versioning information in the patch-image code nor the
Makefile. Consider it as first release by adding PKG_RELEASE.
Motivation is the tracking of changes in the buildsystem, which requires
versioning of packages.
Also update copyright.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This applies to tools directory what has been done for package/ in
commit 9c170cb92f ("package: drop PKG_VERSION for purely local
packages"):
In the package guidelines, PKG_VERSION is supposed to be used as
"The upstream version number that we're downloading", while
PKG_RELEASE is referred to as "The version of this package Makefile".
Thus, the variables in a strict interpretation provide a clear
distinction between "their" (upstream) version in PKG_VERSION and
"our" (local OpenWrt trunk) version in PKG_RELEASE.
For local (OpenWrt-only) packages, this implies that those will only
need PKG_RELEASE defined, while PKG_VERSION does not apply following
a strict interpretation. While the majority of "our" packages actually
follow that scheme, there are also some that mix both variables or
have one of them defined but keep them at "1".
This is misleading and confusing, which can be observed by the fact
that there typically either one of the variables is never bumped or
the choice of the variable to increase depends on the person doing the
change.
Consequently, this patch aims at clarifying the situation by
consistently using only PKG_RELEASE for "our" packages. For tools/,
only three packages were affected. This fixes two of them, and
leaves the remaining wrt350nv2-builder untouched, as the code there
seems to have some versioning of its own that is treated as upstream
version in PKG_VERSION.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds new strings to the support list for the TP-Link CPE210 v3
that are supposed to work with the existing setup.
Without it, the factory image won't be accepted by the vendor UI on
these newer revisions.
Tested on a CPE210 v3.20 (EU).
Ref: https://forum.openwrt.org/t/build-for-cpe210-v3-20/68000
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Firmware is binary blob, so there are barely any NULL terminated strings
expected, so we should probably convert all chars into u8 types, and
after that it's clear, that using strcpy doesn't make sense anymore.
This is rather theoretical stuff, but `uint8_t name[PART_NAME_LENGTH]`
means, that you can supply PART_NAME_LENGTH sized name, not
PART_NAME_LENGTH-1 name when NULL terminated.
Ref: https://github.com/openwrt/openwrt/pull/2274
Fixes: 04cb651376 ("firmware-utils: mkfwimage: fix more errors reported by gcc-6/7/9")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add missing calls to `free` for variable `filebuffer`.
Add missing calls to `fclose` for variables `fd` and `fd_out`.
Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
This device uses the same hardware as RE650 v1 which got supported in
8c51dde.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link RE220 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.
This port of OpenWRT leverages work done by Andreas Böhler <dev@aboehler.at>
for the TP-Link RE200 v2 as both devices share the same SoC, flash layout
and GPIO pinout.
Specifications
MediaTek MT7628AN (580 Mhz)
64 MB of RAM
8 MB of FLASH
2T2R 2.4 GHz and 1T1R 5 GHz
1x 10/100 Mbps Ethernet
UART header on PCB (57600 8n1)
8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled separately.
Web Interface Installation
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Signed-off-by: Rowan Border <rowanjborder@gmail.com>
TP-Link CPE610 v2 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of DDR2 RAM
- 8 MB of SPI-NOR Flash
- 23dBi high-gain directional 2×2 MIMO antenna and a
dedicated metal reflector
- Power, LAN, WLAN5G green LEDs
- 3x green RSSI LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
This patch changes the version code of the image header
from `1.1.99_0.0.0.0` to `99.99.99_99.99.99.99`. This
is neccessary on some devices where the stock firmware
checks the version field, possibly preventing third-party
firmware from being installed.
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
TP-Link RE450 v3 is a dual band router/range-extender based on
Qualcomm/Atheros QCA9563 + QCA9880.
This device is nearly identical to RE450 v2 besides a modified flash
layout (hence I think force-flashing a RE450v2 image will lead to at
least loss of MAC address).
Specification:
- 775 MHz CPU
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 1x 10/100/1000 Mbps Ethernet (AR8033 PHY)
- 7x LED, 4x button-
- possible UART header on PCB¹
Flash instruction:
Apply factory image in OEM firmware web-gui.
¹ Didn't check to connect as I didn't even manage to connect on
RE450v2 (AFAIU it requires disconnecting some resistors, which I was
too much of a coward to do). But given the similarities to v2 I
think it's the same or very similar procedure (and most likely also
the only way to debrick).
Signed-off-by: Andreas Wiese <aw-openwrt@meterriblecrew.net>
[remove dts-v1 and compatible in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
