We have IPQ8064 AP161 board which has three GMAC's
* RGMII x2
* SGMII x1.
The existing ar8327 driver does not have support for
three GMAC's connection, hence this change adds support
for the same. This has been verified on AP148 and AP161
board.
Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Multicast ARL entries can have multiple destination ports. Get and dump
all destination ports of each entry, not just the lowest.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
Driver crash when 'phydev->adjust_link' isn't provided.
This patch check if 'phydev->adjust_link' exist before
call the method.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This patch adds the feature to parse the existing cpu_port DT
property, which is used to specify which port is the cpu port
of the switch.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
On the WNDAP620, the mdio and mdc lines are controlled by
the EMAC ethernet device. This results in a hen-vs-egg problem.
The rtl8367b driver is probed before the ethernet driver and
the mdio-bus is not available yet, which caused the rtl8367b
driver to fail.
This patch changes the rtl8366_smi_probe_of() function to
return -EPROBE_DEFER if the mdio-bus lookup failed and changes
rtl8366_smi_probe()'s signature to return the error code back to
the callee, so it can propagate back to the kernel. Which, will
retry the switch probe at a later time.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently, the b53 MDIO switch driver registers the switch on
config-init and not on device probe. Because of this, the switch
gets added every time the associated interface comes up.
This commit fixes this behavior by registering the switch on device
probe.
Compile- and run-tested on OCEDO Koala.
Signed-off-by: David Bauer <mail@david-bauer.net>
The intention of 967b6be118 ("ar8327: Add workarounds for AR8337
switch") was to remove the register fixups for AR8337. But instead they
were removed for AR8327.
The RGMII RX delay is forced even if the port is used as phy instead of
mac, which results in no package flow at least for one board.
Fixes: FS#1664
Signed-off-by: Mathias Kresin <dev@kresin.me>
Make the call to of_mdiobus_register() dependant on CONFIG_OF to avoid
pulling in an unwanted dependency on of_mdio.ko.
Fixes: 3dc523f232 kernel: add OF support to rtl8355 driver
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This fixes:
drivers/net/phy/b53/b53_priv.h:325:2: error: enumeration value '<board>' not handled in switch [-Werror=switch]
errors.
Fixes: 0de2213eea ("kernel: b53: look for NVRAM's "robo_reset" entry on every platform")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Since kernel 4.1 bcm47xx_nvram_gpio_pin() is now defined in a global
header and can be safely called even on non-Broadcom platforms.
This change makes b53 look for "robo_reset" on ARCH_BCM_5301X and
slightly simplifies the code.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
In kernels 4.0 and older that header file was located in some subdir of
arch/mips/include. Target brcm47xx supports kernels 4.4 and 4.9 only so
that code isn't needed anymore.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Add support to allow for per switch port VLAN priority (PCP) bits
for the ar8327/8337 chip using the swconfig utility.
Tested on Netgear R7800
Signed-off-by: Tan Hong Hui <hhtan72@yahoo.com>
sysfs attributes 'port_mask' & 'speed_mask' held locks whilst doing
mundane tasks such as sprintf. Refactor code to reduce length of time
locks are held unnecessarily.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Add sysfs 'mode' attribute to swconfig controlled LEDs.
swconfig 'link state' LEDs blink in the presence of port traffic. This
behaviour becomes more obvious as switches start to support
get_port_stats() e.g. commits 0369e35891,
3056d09b40,
4ddbc43cc1,
4d8a66d934.
This blinking can be confusing/distracting if the switch has other LEDs
used to indicate traffic. Provide a 'mode' sysfs attribute that
controls the blink on traffic behaviour.
mode - either "none" (LED is off) or a space separated list of one or more:
link: LED's normal state reflects whether the link is up (has carrier) or not
tx: LED blinks on transmitted data
rx: LED blinks on receive data
Note that 'link' considers any port speed mask that may be applicable.
e.g. if an LED is configured to indicate 1Gbit link speed and mode is
set to 'link rx tx' but the port is connected at 100Mbit then the LED
will not light or blink. A mode of 'tx rx' will blink in the presence of
traffic only if the port matches the rate (if configured)
This maintains compatibility with existing behaviour.
Attribute is 'link tx rx' by default for backwards compatible behaviour.
Many thanks to Thibaut Varene for providing a more sensible led_event
routine after I had mangled the original, and other coding style hints.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Acked-by: Thibaut VARENE <hacks@slashdirt.org>
The D-Link devices with JBOOT bootloader use their own kernel
image header (stag + sch2 headers).
This driver find jImage header and set rootfs start after kernel file.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This adds initial support for kernel 4.14 based on the patches for
kernel 4.9.
In the configuration I deactivated some of the new possible security
features like:
CONFIG_REFCOUNT_FULL
CONFIG_SLAB_FREELIST_HARDENED
CONFIG_SOFTLOCKUP_DETECTOR
CONFIG_WARN_ALL_UNSEEDED_RANDOM
And these overlay FS options are also deactivated:
CONFIG_OVERLAY_FS_INDEX
CONFIG_OVERLAY_FS_REDIRECT_DIR
I activated this:
CONFIG_FORTIFY_SOURCE
CONFIG_POSIX_TIMERS
CONFIG_SLAB_MERGE_DEFAULT
CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED
I am not sure if I did the porting correct for the following patches:
target/linux/generic/backport-4.14/020-backport_netfilter_rtcache.patch
target/linux/generic/hack-4.14/220-gc_sections.patch
target/linux/generic/hack-4.14/321-powerpc_crtsavres_prereq.patch
target/linux/generic/pending-4.14/305-mips_module_reloc.patch
target/linux/generic/pending-4.14/611-netfilter_match_bypass_default_table.patch
target/linux/generic/pending-4.14/680-NET-skip-GRO-for-foreign-MAC-addresses.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The splitter ignored the rootfs offset from the header, probably
because until c1e6e61 it was invalid.
This patch fixes the splitter to use the now correct header data.
Regarding target/linux/ar71xx/files/drivers/mtd/tplinkpart.c,
this particular splitter "falls back" to the correct rootfs offset
reading and as such it doesn't need to be updated, although it will
report a kernel partition length that can be larger than the actual
length as it assumes that partition fills the entire segment up to
the rootfs partition.
Tested-by: Mathias Kresin <dev@kresin.me>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Tested-by: Henryk Heisig <hyniu@o2.pl>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
check if the config option CONFIG_LANTIQ is defined.
This fixes the following warning:
CC [M] drivers/misc/owl-loader.o
drivers/misc/owl-loader.c: In function 'ath9k_pci_fixup':
drivers/misc/owl-loader.c:92:5: warning: "CONFIG_LANTIQ" is not defined [-Wundef]
#if CONFIG_LANTIQ
^
Fixes: e9401a2335 ("kernel: owl-loader for delayed Atheros ath9k fixup")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The implementation is not efficient on ar8xxx switches. It triggers high
CPU load and degrades device performance.
The high CPU load has been traced down to the ar8xxx_reg_wait() call in
ar8xxx_mib_op(), which has to usleep_range() till the MIB busy flag set
by the request to update the MIB counter is cleared.
This commit removes the get_port_stats() code introduced in 4d8a66d and
leaves a note for future hacker's beware.
Fixes: FS#1004
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
In case the link changes from down to up, the register is only updated
on read. If the link failed/was down, this bit will be 0 until after
reading this bit again.
Fixes a reported link down by swconfig alebit the link is up (query for
the link again will show the correct link status)
Signed-off-by: Mathias Kresin <dev@kresin.me>
This generic structure defines tx_bytes and rx_bytes as unsigned long (u32),
while several devices would typically report unsigned long long (u64).
The code can work as is, but there's a chance that with a sufficiently fast
interface the overflow might happen too fast to be correctly noticed by the
consumers of this data.
This patch makes both field unsigned long long and updates the only known
consumer of this data: swconfig_leds.c
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
The implementation uses a generic callback that select the correct MIB counter
index based on chip version.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
On the Linksys WRT54GSv1, the adm6996 switch driver and the
gpio_button_hotplug module both claim GPIO 6, which is connected to the
Reset button. When the switch driver's request wins, the Reset button
cannot work. This makes it impossible to enter failsafe mode without a
serial console.
Stop requesting the "adm_rc" GPIO in the switch driver, since it is not
used anywhere.
Fixes FS#792.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
PHY core treats any positive return value as the auto-negotiation done
indication. Since we do not actually check any device register in this
callback then update it to return positive value with a neutral meaning
instead of the register flag to avoid confusing for future readers.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
The Marvel 88E6060 switch has an MDIO interface, but does not emulate
regular PHY behavior for the host. The network core can not detect using
the generic code, whether the connection via the attached PHY can be
used or not. The PHY's state machine is stuck in a state of
auto-negotiation and does not go any further so the Ethernet interface
of the router stay forever in the not-runing state.
Fix this issue by implementing the aneg_done callback to be able to
inform the network core that the Ethernet interface link to which the
switch is connected can be marked as RUNNING.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
