The MikroTik wAP ac (RBwAPG-5HacD2HnD) is a dual-band dual-radio
802.11ac wireless access point with integrated antenna and two Ethernet
ports in a weatherproof enclosure. See
https://mikrotik.com/product/wap_ac for more information.
Important: this is the new ipq40xx-based wAP ac, not the older
ath79-based wAP ac (RBwAPG-5HacT2HnD), already supported in OpenWrt.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- CPU: 4x ARM Cortex A7
- RAM: 128MB
- Storage: 16MB NOR flash
- Wireless
- 2.4GHz: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
- 5GHz: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
- Ethernet: Built-in IPQ4018 (SoC, QCA8075), 2x 1000/100/10Mb/s ports,
one with 802.3af/at PoE in
Installation:
Boot the initramfs image via TFTP, then flash the sysupgrade image using
sysupgrade. Details at https://openwrt.org/toh/mikrotik/common.
Notes:
This preserves the MAC addresses of the physical Ethernet ports:
- eth0 corresponds to the physical port labeled ETH1 and has the base
MAC address. This port can be used to power the device.
- eth1 corresponds to the physical port labeled ETH2 and has a MAC
address one greater than the base.
MAC addresses are set from /lib/preinit/05_set_iface_mac_ipq40xx.sh
rather than /etc/board.d/02_network so that they are in effect for
preinit. This should likely be done for other MikroTik devices and
possibly other non-MikroTik devices as well.
As this device has 2 physical ports, they are each connected to their
respective PHYs, allowing the link status to be visible to software.
Since they are not marked on the case with any role (such as LAN or
WAN), both are bridged to the lan network by default, although this can
easily be changed if needed.
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Now that libiconv-stub is gone, a replacement for its host build is
needed.
Fixes: c0ba4201f8 ("libiconv-stub: remove")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
moves and extends the current facilities, which have been
added some time ago for the the usbip utility, to support
more utilites that are shipped with the Linux kernel tree
to the SDK.
this allows to drop all the hand-waving and code for
failed previous attempts to mitigate the SDK build failures.
Fixes: bdaaf66e28 ("utils/spidev_test: build package directly from Linux")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Accessing the console on many devices is difficult.
netconsole eases debugging on devices that crash
after the network is up.
Reference to the netconsole documentation in upstream Linux:
<https://www.kernel.org/doc/html/latest/networking/netconsole.html>
|
|netconsole=[+][src-port]@[src-ip]/[<dev>],[tgt-port]@<tgt-ip>/[tgt-macaddr]
|
| where
| + if present, enable extended console support
| src-port source for UDP packets (defaults to 6665)
| src-ip source IP to use (interface address)
| dev network interface (eth0)
| tgt-port port for logging agent (6666)
| tgt-ip IP address for logging agent
| tgt-macaddr ethernet MAC address for logging agent (broadcast)
OpenWrt specific notes:
OpenWrt's device userspace scripts are attaching the network
interface (i.e. eth0) to a (virtual) bridge (br-lan) device.
This will cause netconsole to report:
|network logging stopped on interface eth0 as it is joining a master device
(and unfortunately the traffic/logs to stop at this point)
As a workaround, the netconsole module can be manually loaded
again after the bridge has been setup with:
insmod netconsole netconsole=@/br-lan,@192.168.1.x/MA:C...
One way of catching errors before the handoff, try to
append the /etc/modules.conf file with the following extra line:
options netconsole netconsole=@/eth0,@192.168.1.x/MA:C...
and install the kmod-netconsole (=y) into the base image.
Signed-off-by: Catalin Toda <catalinii@yahoo.com>
(Added commit message from PR, added links to documentation)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The change of the PKG_VERSION caused the hash of the package to
change. This is because the PKG_VERSION is present in the
internal directory structure of the uboot-layerscape-21.08.tar.xz
archive.
i.e:
# tar tf uboot-layerscape-21.08.tar.xz:
uboot-layerscape-21.08/
uboot-layerscape-21.08/.azure-pipelines.yml
uboot-layerscape-21.08/.checkpatch.conf
uboot-layerscape-21.08/.gitattributes
uboot-layerscape-21.08/.github/
[...]
vs.
# tar tf uboot-layerscape-LSDK-21.08.tar.xz
uboot-layerscape-LSDK-21.08/
uboot-layerscape-LSDK-21.08/.azure-pipelines.yml
uboot-layerscape-LSDK-21.08/.checkpatch.conf
uboot-layerscape-LSDK-21.08/.gitattributes
uboot-layerscape-LSDK-21.08/.github/
[...]
the (file) content of both archives are otherwise the same.
The PKG_HASH was taken from the builder log:
| Hash of the local file uboot-layerscape-21.08.tar.xz does not match
|(file: 54909a98bdcc26c7f9b35b35fcae09b977ecbf044be7bffa6dad9306c47cccf6,
|requested: 874e871755ef84ebbf3[...]) - deleting download.
without this update, the uboot-layerscape-21.08 package would
always try to download (from git), repacked the archive and
reupload to sources.openwrt.org (~14 MiB saved).
Fixes: 038d5bdab1 ("layerscape: use semantic versions for LSDK")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
those board files can/should be dropped now too.
Fixes: 50c232d6f4 ("ipq-wifi: drop upstreamed board-2.bin")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
the tacked on @TARGET_bcm53xx causes warnings:
tmp/.config-package.in:14027:warning: ignoring unsupported character '@'
tmp/.config-package.in:26028:warning: ignoring unsupported character '@'
this was wrong.
Fixes: be1761fa14 ("nu801: add MR26 to the table")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ef5d3e3 jail: fix various ignoring return value compilation warning
8e4a956 jail: add WARNING macro to log non critical warning message
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Destination switch ports for outgoing frame can range from 0 to
CPU_PORT-1.
Refactor the code to only generate egress frame CPU headers when a valid
destination port number is available, and make the code a bit more
consistent between different switch generations. Change the dest_port
argument's type to 'unsigned int', since only positive values are valid.
This fixes the issue where egress frames on switch port 0 did not
receive a VLAN tag, because they are sent out without a CPU header.
Also fixes a potential issue with invalid (negative) egress port numbers
on RTL93xx switches.
Reported-by: Arınç ÜNAL <arinc.unal@xeront.com>
Suggested-by: Birger Koblitz <mail@birger-koblitz.de>
Tested-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Priority values passed to the egress (TX) frame header initialiser are
invalid when smaller than 0, and should not be assigned to the frame.
Queue assignment is then left to the switch core logic.
Current code for RTL83xx forces the passed priority value to be
positive, by always masking it to the lower bits, resulting in the
priority always being set and enabled. RTL93xx code doesn't even check
the value and unconditionally assigns the (32 bit) value to the (5 bit)
QID field without masking.
Fix priority assignment by only setting the AS_QID/AS_PRI flag when a
valid value is passed, and properly mask the value to not overflow the
QID/PRI field.
For RTL839x, also assign the priority to the right part of the frame
header. Counting from the leftmost bit, AS_PRI and PRI are in bits 36
and 37-39. The means they should be assigned to the third 16 bit value,
containing bits 32-47.
Tested-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The flag to enable L2 address learning on egress frames is in CPU header
bit 40, with bit 0 being the leftmost bit of the header. This
corresponds to BIT(7) in the third 16-bit value of the header.
Correctly set L2LEARNING by fixing the off-by-one error.
Fixes: 9eab76c84e ("realtek: Improve TX CPU-Tag usage")
Tested-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The flag to enable the outgoing port mask is in CPU header bit 43, with
bit 0 being the leftmost bit of the header. This corresponds to BIT(4)
in the third 16-bit value of the header.
Correctly set AS_DPM by fixing the off-by-one error.
Fixes: 9eab76c84e ("realtek: Improve TX CPU-Tag usage")
Tested-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
46a33b8 kmodloader: fix compilation warning with not checking return of asprintf
Also switch PKG_RELEASE to AUTORELEASE.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This version fixes two vulnerabilities:
-CVE-2022-34293[high]: Potential for DTLS DoS attack
-[medium]: Ciphertext side channel attack on ECC and DH operations.
The patch fixing x86 aesni build has been merged upstream.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Meraki MR26 is an EOL wireless access point featuring a
PoE ethernet port and two dual-band 3x3 MIMO 802.11n
radios and 1x1 dual-band WIFI dedicated to scanning.
Thank you Amir for the unit and PSU.
Hardware info:
SOC : Broadcom BCM53015A1KFEBG (dual-core Cortex-A9 CPU at 800 MHz)
RAM : SK hynix Inc. H5TQ1G63EFR, 1 Gbit DDR3 SDRAM = 128 MiB
NAND : Spansion S34ML01G100TF100, 1 Gbit SLC NAND Flash = 128 MiB
ETH : 1 GBit Ethernet Port - PoE
WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn
WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn
WIFI3 : Broadcom BCM43428 abgn (1x1:1 - id: 43428)
BUTTON: one reset button
LEDS : RGB-LED
MISC : Atmel AT24C64 8KiB EEPROM (i2c - seems empty)
: Ti INA219 26V, 12-bit, i2c output current/voltage/power monitor
: TPS23754, High Power/High Efficiency PoE Interface+DC/DC Controller
SERIAL:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
right angle 1x4 0.1" pinheader.
The pinout is: VCC (next to J3, has little white arrow), RX, TX, GND.
This flashing procedure for the MR26 was tested with firmware:
"22-143410M-gf25cbf5a-asa".
U-Boot 2012.10-00063-g83f9fe4 (Jun 04 2014 - 21:22:39)
A guide how to open up the device is available on the wiki:
<https://openwrt.org/toh/meraki/mr26>
Notes:
- The WIFI do work to a degree. Limited to 802.11bg in the 2.4GHz band.
- the WIFI macs are made up.
0. Create a separate Ethernet LAN which can't have access to the internet.
Ideally use 192.168.1.2 for your PC. The new OpenWrt firmware will setup
the network via DHCP Discovery, so make sure your PC is running
a DHCP-Server (i.e.: dnsmasq)
'# dnsmasq -i eth# -F 192.168.1.5,192.168.1.50
Download the openwrt-meraki-mr26 initramfs file from openwrt.org and
rename it to something simple like mr26.bin. Then put it into the tftp's
server directory.
1. Disassemble the MR26 device by removing all screws (4 screws are located
under the 4 rubber feets!) and prying open the plastic covers without
breaking the plastic retention clips. Once inside, remove the plastic
back casing. Be careful, there some "hidden" retention clips on both
sides of the LAN port, you need a light to see those. Next, you want to
remove all the screws on the outer metal shielding to get to the PCB.
It's not necessary to remove the antennas!
2. Connect the serial cable to the serial header and Ethernet patch cable
to the device.
4. Before connecting the power, get ready flood the serial console program
with the magic: xyzzy . This is necessary in order to get into the
u-boot prompt. Once Ready: connect power cable.
5. If you don't get the "u-boot>" prompt within the first few seconds,
you have to disconnect and reconnect the power cable and try again.
6. In the u-boot prompt enter:
setenv ipaddr 192.168.1.4
setenv serverip 192.168.1.2
tftpboot ${meraki_loadaddr} mr26.bin; bootm
this will boot a in-ram-only OpenWrt image.
7. Once it booted use sysupgrade to permanently install OpenWrt.
To do this: Download the latest sysupgrade.bin file and move
it to the device. Then use sysupgrade *sysupgrade.bin to install it.
WARNING: DO NOT DELETE the "storage" ubi volume!
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
the legacy driver was dropped in linux 5.14-rc3:
commit d249ff28b1d8 ("intersil: remove obsolete prism54 wireless driver")
Quoting Lukas Bulwahn:
"p54 replaces prism54 so users should be unaffected."
Reported-by: Marius Dinu <m95d+git@psihoexpert.ro>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The spidev_test is build in phase2 even though it should be disabled.
My best guess is that we hit the same issue that I had with nu801.
The build-system thinks it's a tool that is necessary for
building the kernel.
In this case, the same fix (adding a dependency on the presence of
the module) could work in this case as well?
Fixes: bdaaf66e28 ("utils/spidev_test: build package directly from Linux")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The BDFs for the:
GL.iNet GL-B2200
were upstreamed to the ath10k-firmware repository
and landed in linux-firmware.git
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
gettext (libintl-stub) was removed in commit [1], so the libintl-stub
lib and include directories aren't existing anymore. This commit cleans
up the INTL flags for the BUILD_NLS=n case.
[1] e6f569406f
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Reviewed-by: Rosen Penev <rosenp@gmail.com>
Kalle:
"I see that variant has a space in it, does that work it correctly? My
original idea was that spaces would not be allowed, but didn't realise
to add a check for that."
Is this an easy change? Because the original author (Tim Davis) noted:
"You may substitute the & and space with something else saner if they
prove to be problematic."
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This PR allows a user to enable a private psk, where each station
may have it's own psk or use a common psk if it is not defined.
The private psk is defined using the sta's mac and a radius server
is required.
ppsk option should be enabled in the wireless configuration along with
radius server details. When using PPSK, the key is ignored, it will be
retrieved from radius server. SAE is not yet supported (private sae) in
hostapd.
Wireless example configuration:
option encryption 'psk2+ccmp'
option ppsk '1'
option auth_server '127.0.0.1'
option auth_secret 'radiusServerPassword'
If you want to use dynamic VLAN on PPSK also include:
option dynamic_vlan '2'
option vlan_tagged_interface 'eth0'
option vlan_bridge 'br-vlan'
option vlan_naming '0'
It works enabling mac address verification on radius server and
requiring the tunnel-password (the private psk) from radius server.
In the radius server we need to configure the users. In case of
freeradius: /etc/freeradius3/mods-config/files/authorize
The user and Cleartext-Password should be the mac lower case using the
format "aabbccddeeff"
<sta mac> Cleartext-Password := "<sta mac>"
Tunnel-Password = <Private Password>
Example of a user configured in radius and using dynamic VLAN5:
8cb84a000000 Cleartext-Password := "8cb84a000000"
Tunnel-Type = VLAN,
Tunnel-Medium-Type = IEEE-802,
Tunnel-Private-Group-ID = 5,
Tunnel-Password = MyPrivPw
If we want to have a default or shared psk, used when the mac is not
found in the list, we need to add the following at the end of the radius
authorize file:
DEFAULT Auth-Type := Accept
Tunnel-Password = SharedPw
And if using VLANs, for example VLAN6 for default users:
DEFAULT Auth-Type := Accept
Tunnel-Type = VLAN,
Tunnel-Medium-Type = IEEE-802,
Tunnel-Private-Group-ID = 6,
Tunnel-Password = SharedPw
Signed-off-by: Manuel Giganto <mgigantoregistros@gmail.com>
Before this commit, it was assumed that aclocal.real is in the PATH. While
this was fine for the normal build workflow, this led to some issues if
make TOPDIR="$(pwd)" -C "$pkgdir" compile
was called manually. The command failed with:
/home/.../openwrt/staging_dir/host/bin/aclocal: line 2: aclocal.real: command not found
autoreconf: /home/.../openwrt/staging_dir/host/bin/aclocal failed with exit status: 127
After the commit, the package is built sucessfully.
Signed-off-by: Leonardo Mörlein <me@irrelefant.net>
the hash and timestamp of the remote copy of the archive
has changed since last bump
meaning the remote archive copy was recreated
Signed-off-by: Michael Pratt <mcpratt@pm.me>
kernel linux now have 2 different export.h include, one from
linux/export.h and one from asm-generic/export.h
While most of our target user linux/export.h, aarch64 based target use
asm-generic/export.h that is not patched with the changes of
221-module_exports.
Patch also this additional header to fix multiple
aarch64-openwrt-linux-musl-ld: warning: orphan section `__ksymtab_strings' from `arch/arm64/kernel/head.o' being placed in section `__ksymtab_strings'
warning during kernel compilation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patches does not have a valid patch headers and does not apply on
an external git tree with 'git am'. To fix this add the missing headers.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
This patches does not have a valid patch headers and does not apply on
an external git tree with 'git am'. To fix this add the missing headers.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
For some reason, current coreutils version installed on x86 macOS via homebrew
have a bug, where at least the cc1 binary from gcc gets corrupted during install
to the staging dir.
Using the install utility from tools/coreutils fixes this
Signed-off-by: Felix Fietkau <nbd@nbd.name>
swig has been installed on the buildbots a while a ago and
Petr Štetiar got a fix for the pylibfdt error. Use that and re-enable
the builds for mt7620 and mt7621.
Refresh patches while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Let U-Boot handle free space in UBI partitions by recognizing the EOF
marker OpenWrt is using as well for that purpose.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Buidbots are throwing the following compile error:
In file included from tools/aisimage.c:9:
include/image.h:1133:12: fatal error: openssl/evp.h: No such file or directory
^~~~~~~~~~~~~~~
compilation terminated.
Fix it by passing `UBOOT_MAKE_FLAGS` variable to make.
Suggested-by: Petr Štetiar <ynezz@true.cz>
Fixes: 6d5611af28 ("uboot-at91: update to linux4sam-2022.04")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Building U-Boot for the MT7621 SoC requires binman, a Python-based
host tool to generate images. For now, binman cannot work inside the
OpenWrt build system because it requires swig, so mark the MT7621
boards as borken to fix the ramips/mt7621 build until someone with
knowledge about Python and swig fixes the underlaying issue.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Buidbots are currently choking on the following compile error:
In file included from tools/aisimage.c:9:
include/image.h:1133:12: fatal error: openssl/evp.h: No such file or directory
# include <openssl/evp.h>
^~~~~~~~~~~~~~~
compilation terminated.
This is caused by a complete overriding of make flags which are provided
correctly in `UBOOT_MAKE_FLAGS` variable, but currently overriden
instead of extended. This then leads to the usage of build host include
dirs, which are not available.
Fix it by extending `UBOOT_MAKE_FLAGS` variable like it was done in
commit 481339a042 ("uboot-imx: fix wrong make flags overriding").
Fixes: 7094e65503 ("uboot-imx: add support for TechNexion PICO-PI-IMX7D")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The amber and green wan led color was inverted in dts file, which ends
up leaving the wan led amber when the connection is established, so,
switch gpio led number (7 and 8) in qca9563_tplink_archer-c6-v2-us.dts.
Tip: the /etc/config/system file needs to be regenerated.
Signed-off-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit subject]
Linux stable v5.15.51 brought commit 7a3a4683562e
("ARM: dts: bcm2711-rpi-400: Fix GPIO line names") which was already
part of a local patch which then failed to apply. Remove the already
applied and now failing hunk from the patch to fix the build.
Fixes: 552d76f2be ("kernel: bump 5.15 to 5.15.51")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* Merge uboot-ramips into uboot-mediatek.
* Port support for the RAVPower RP WD009 to U-Boot 2022.07.
* Add support for MT7621 and add builds for the reference boards.
* Add builds for MT7620 and MT7628 reference boards.
This should help to make development of U-Boot-level board support for
all MediaTek targets much easier.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
