Commit Graph

4 Commits

Author SHA1 Message Date
Elbert Mai
28d15e2040 mediatek: filogic: add support for Ubiquiti UniFi 6 Plus (U6+)
Ubiquiti U6+ is a dual-band WiFi 6 PoE access point.
It is a drop-in upgrade of the U6 lite.

Specifications
---

- SoC: MediaTek MT7981A dual-core ARM Cortex-A53 1.3 GHz
- RAM: 256 MB DDR3-2133 RAM
- Flash: 16 MB SPI NOR and 4 GB eMMC
- LAN: 1x Gigabit Ethernet with 802.3af/at support
- WLAN: MediaTek MT7976C 2x2 MIMO dual-band WiFi 6
- LEDs: 1x blue and 1x white
- Buttons: 1x reset button

Installation
---

1. Power device using a PoE injector or switch
2. Connect via Ethernet to the device with static IP 192.168.1.2
3. SSH into the device with password: ubnt

        $ ssh ubnt@192.168.1.20

4. Unlock kernel partitions for writing

        $ echo 5edfacbf > /proc/ubnthal/.uf

5. Confirm correct partitions

        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p6/uevent
        PARTNAME=kernel0
        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p7/uevent
        PARTNAME=kernel1
        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p8/uevent
        PARTNAME=bs

6. Set and confirm bootloader environment

        $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt"
        $ fw_setenv bootcmd_real "run boot_openwrt"
        $ fw_printenv

7. Copy sysupgrade image to /tmp/openwrt.bin via scp
8. Copy kernel and rootfs to mmcblk0p6 and mmcblk0p7, respectively

        $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/kernel -O | dd of=/dev/mmcblk0p6
        $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/root -O | dd of=/dev/mmcblk0p7

9. Ensure device boots from mmcblk0p6

        $ echo -ne "\x00\x00\x00\x00\x2b\xe8\x4d\xa3" > /dev/mmcblk0p8

10. Reboot the device

        $ reboot

Signed-off-by: Elbert Mai <code@elbertmai.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit 75ee5546e9)
2023-12-07 09:45:33 +01:00
Tianling Shen
d3c193525e mediatek: add CMCC RAX3000M support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 64GB eMMC or 128 MB SPI-NAND
  RAM: 512MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Mesh
  Power: DC 12V 1A
- UART: 3.3v, 115200n8
  --------------------------
  |         Layout         |
  |   -----------------    |
  | 4 | GND TX VCC RX | <= |
  |   -----------------    |
  --------------------------

Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
   tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
   'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
   tar -zcf cfg_export_config_file.conf etc/
   * If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
     just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.

Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH    CMIIT ID: xxxx" is NAND version

eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
   ('data' partition can be ignored, it's useless.)
2. Write new GPT table:
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
   echo 0 > /sys/block/mmcblk0boot0/force_ro
   dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
   dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync

NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
   mtd erase BL2
   mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
   mtd erase FIP
   mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
   ubidetach -p /dev/mtd0
   ubiformat -y /dev/mtd0
   ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
   ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
   ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
   ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 423186d7d8)
[rebased to 23.05]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-11-07 00:46:00 +01:00
David Bauer
c697057b7c mediatek: add support for Acer Predator W6
Hardware
--------
SOC:   MediaTek MT7986A
RAM:   1GB DDR4
FLASH: 4GB eMMC
WiFi:  2x2 2.4 GHz 802.11 b/g/n/ax MT7916 DBDC
       4x4 5 GHz   802.11 a/n/ac/ax MT7986
       2x2 6 GHz   802.11ax MT7916 DBDC
ETH:   4x LAN 1Gbit/s (MT7531)
       1x WAN 2.5Gbit/s (GPY211)
BTN:   RESET, WPS
LED:   Antenna LEDs (GPIO)
       Mood-LED (Kinetic KTD2601) - unsupported
UART:  Header nest to USB port - 3V3 115200 8N1
       [BUTTON] GND - RX - TX [USB]

Installation
------------

1. Connect to the device using serial console.

2. Interrupt the Autoboot process when promted by sending '0' twice.

3. Serve the OpenWrt initramfs image using TFTP at 192.168.1.66. Name
   the image "predator.bin" and conenct the TFTP server to the routers
   LAN port.

4. Configure U-Boot to allow loading unsigned images from MMC

   $ setenv bootcmd 'mmc read 0x40000000 0x00004400 0x0010000;
     fdt addr $(fdtcontroladdr); fdt rm /signature; bootm 0x40000000';
     saveenv

5. Transfer the image from U-Boot

   $ setenv serverip 192.168.1.66; setenv ipaddr 192.168.1.1;
     tftpboot 0x46000000 predator.bin; fdt addr $(fdtcontroladdr);
     fdt rm /signature; bootm

6. Wait for OpenWrt to boot

7. Transfer the OpenWrt sysupgrade image to the router using scp.

8. Install OpenWrt using sysupgrade.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 7e7eb5312d)
2023-08-05 18:49:34 +02:00
David Bauer
e7c399bee6 filogic: add support for ASUS TUF-AX4200
Hardware
--------
SOC:   MediaTek MT7986
RAM:   512MB DDR3
FLASH: 256MB SPI-NAND (Winbond W25N02KV)
WIFI:  Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH:   MediaTek MT7531 Switch
       MaxLinear GPY211C 2.5 N-Base-T PHY
UART:  3V3 115200 8N1 (Pinout silkscreened / Do not ocnnect VCC)

Installation
------------

1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
   reachable at 192.168.1.66/24. Rename the image to tufax4200.bin.

2. Connect the TFTP server to the AX4200. Conect to the serial console,
   interrupt the autoboot process by pressing '4' when prompted.

3. Download & Boot the OpenWrt initramfs image.

   $ setenv ipaddr 192.168.1.1
   $ setenv serverip 192.168.1.66
   $ tftpboot 0x46000000 tufax4200.bin
   $ bootm 0x46000000

4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
   using scp and install using sysupgrade.

   $ sysupgrade -n <path-to-sysupgrade.bin>

Missing features
----------------

 - The LAN port LEDs are driven by the switch but OpenWrt does not
   correctly configure the output.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-03-24 20:30:29 +01:00