Commit Graph

60423 Commits

Author SHA1 Message Date
Daniel Golle
eb13076e77 mediatek: fix DTS defining mt7530 switch phys but not referencing them
The upstream solution to define the MDIO bus in DT is a bit
more strict than our previous downstream solution doing the same thing
and now requires switch PHYs to be referenced in DT as well.

Arınç Ünal told us in #15141:
"With [the now upstream patch written by him which we backported], the
switch MDIO bus won't be assigned to ds->user_mii_bus when the switch
MDIO bus is defined on the device tree anymore. This was not the case
with the downstream patch.

When ds->user_mii_bus is populated, DSA will 1:1 map the port with
PHY. Meaning port with address 1 will be mapped to PHY with address 1.
Because that ds->user_mii_bus is not populated when the switch MDIO
bus is defined on the device tree, on every port node, the PHY address
must be supplied by the phy-handle property."

Add those phy-handles to affected devices' DT.

Fixes: 4354b34f6f ("generic: 6.6: sync mt7530 DSA driver with upstream")
Fixes: 401a6ccfaf ("generic: 6.1: sync mt7530 DSA driver with upstream")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-04-13 18:49:30 +01:00
Mieczyslaw Nalewaj
c08f8a4a49 ramips: add support for TP-Link EC220-G5 v2
TP-Link EC220-G5 v2 is a dual band router with 4 GbE ports
Advertised as AC1200 for its 867Mbps (2x2) 5GHz band
and 300 Mbps (2x2) 2.4GHz band.

Specs:
- SoC: MediaTek MT7620A
- Ethernet: 4x GbE ports (Realtek RTL8367S)
- Wireless 2.4GHz: MediaTek MT7620A
- Wireless 5GHz: MediaTek MT7612E
- RAM: 64MiB
- ROM: 8MiB (W25Q64BV)
- 2 Buttons (WPS and reset)
- 7 LEDs

Flash instructions via serial console:
1. Rename the factory.bin to to test.bin
2. start a TFTP server from IP address 192.168.0.225 and serve the image named test.bin
3. connect your device to the LAN port
4. power up the router and press 4 on the console to stop the boot process.
5. enter the following commands on the router console
	tftp 0x80060000 test.bin
	erase tplink 0x20000 0x7a0000
	cp.b 0x80060000 0x20000 0x7a0000
	reset

Flash instructions via TFTP:
1. Update orginal firmware of the router to the latest one.
2. Rename openwrt-ramips-mt7620-tplink_ec220-g5-v2-squashfs-tftp-recovery.bin to tp_recovery.bin
3. Change computer IP to 192.168.0.66
4. Run TFTP serwer
5. Start the router with the reset button pressed, the file will be automatically downloaded and after a while the router will restart.
6. After updating, set your computer's IP to DHCP

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-04-13 17:40:51 +02:00
Mieczyslaw Nalewaj
ada3c41acd ramips: mt7620a_tplink_archer.dtsi rename to mt7620a_tplink_8m.dtsi
Change the name mt7620a_tplink_archer.dtsi to mt7620a_tplink_8m.dtsi because it will also be a base for TP-Link non-Archer routers.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-04-13 17:40:51 +02:00
Mieczyslaw Nalewaj
6258492e1b ramips: TP-Link Archer C2 v1: simplification of the dts definition
Import from the mt7620a_tplink_archer.dtsi file and thus simplify the rest of the definition.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-04-13 17:40:51 +02:00
Mieczyslaw Nalewaj
c97be14c8c ramips: mt7620a_tplink_archer.dtsi - remove unnecessary nvmem-cells definitions
Remove unnecessary nvmem-cells definitions that are being redefined anyway.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-04-13 17:40:51 +02:00
Felix Fietkau
ab9a29a320 mac80211: improve mesh fast tx patch
Change hash key struct size for faster lookup.
Fix clearing cache entries for forwarding

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-04-13 16:33:45 +02:00
Felix Fietkau
1ee5b7e506 hostapd: fix a crash corner case
On some setup failures, iface->bss can be NULL

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-04-13 16:33:45 +02:00
Tianling Shen
0db68a789f uboot-d1: define default BUILD_SUBTARGET
As commit 3ce1e4c3d3 ("d1: define subtarget specifically") added the
'generic' subtarget, without 'BUILD_SUBTARGET' the correspond U-Boot
package will be no longer selected automatically.

Fixes: 3ce1e4c3d3 ("d1: define subtarget specifically")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-04-13 13:41:41 +02:00
Stijn Tintel
291efaf765 realtek: fix filter_port_list_reverse calls
The function introduced in commit 7cbfe5654d is named
filter_port_list_reverse, not filter_port_list_reversed.

Fixes the following error on hpe,1920-8g-poe-65w and
hpe,1920-8g-poe-180w.

  /bin/board_detect: /etc/board.d/02_network: line 84: filter_port_list_reversed: not found

Fixes: 7cbfe5654d ("realtek: move port filtering out of uci_set_poe()")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Sander Vanheule <sander@svanheule.net>
2024-04-13 13:22:11 +03:00
Robert Marko
166ed4f50a CI: labeler: add d1 target
Add support for 'd1' target and its specific packages in labeler.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-04-13 11:25:52 +02:00
Tony Ambardar
4d8a9a954a bpftool: Update to v7.4.0
Update to the latest upstream release to include recent improvements and
bugfixes. Update copyright, fix typo in PKG_NAME, and remove unneeded use
of MAKE_VARS definition in Makefile. Drop 001-cflags.patch and simplify
002-includes.patch after refreshing. Also simplify LTO/DCE build flags.

Link: https://github.com/libbpf/bpftool/releases/tag/v7.4.0
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2024-04-13 11:20:41 +02:00
Tony Ambardar
5b07c37dfa libbpf: Update to v1.4.0
Update to the latest upstream release to include recent improvements and
bugfixes, and update copyright. Remove MAKE_VARS usage in Makefile and drop
001-cflags.patch which are no longer needed. Also add flags to disable LTO,
mistakenly dropped earlier.

Link: https://github.com/libbpf/libbpf/releases/tag/v1.4.0
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2024-04-13 11:20:41 +02:00
Paul Spooren
2496f436a8
build: use zstd for IB, toolchain, SDK and LLVM compression
Use similar efficient but faster compression algorithm.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2024-04-13 08:05:04 +02:00
Olliver Schinagl
98235e60ed scripts/kernel_bump: Delete merge commit
While we have included the needed changes via a merge commit, there is
no need to keep it. Lets drop the merge commit, which we can do as we
haven't pushed anything.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2024-04-12 18:20:53 +02:00
Olliver Schinagl
71c663bcfd scripts/kernel_bump: Allow bumping sub-targets
Some targets may need to bump specific sub-targets only. So lets offer
this as an option.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2024-04-12 18:20:53 +02:00
Olliver Schinagl
b62aafc99a scripts/kernel_bump: Use the git index to find the needed config files
The current solution using `find` introduces a racecondition, where `find`
and `git mv` get in each others way. While this could be fixed with
more-utils sponge command (or even sort -u) to buffer the output of
find.

However, a much better approach, is to query the git index directly,
which will not change, and is far more accurate.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2024-04-12 18:20:53 +02:00
Olliver Schinagl
8ed187e471 scripts/kernel_bump: Use git to obtain the list of files
Instead of looping of a directory to find directories related to kernel
changes, use the git index instead.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2024-04-12 18:20:52 +02:00
Olliver Schinagl
9e6c4392f8 scripts/kernel_bump: Allow for migrating only configuration files
In some cases, we want to only migrate configuration files, e.g. if the
kernel was bumped already. Lets add a flag for this case to offer
flexibility. By default we will migrate configuration flags as before.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2024-04-12 18:20:52 +02:00
Olliver Schinagl
9f0cc3eb11 scripts/kernel_bump: Run script relative to the script dir
Determine the target directory based on the script location, which might
work better in some cases, but at least also allows the script to be ran
from with any location in the OpenWRT repository.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2024-04-12 18:20:52 +02:00
Olliver Schinagl
f9ac106779 scripts/kernel_bump: Do no run on dirty repositories
We want to avoid starting a process when we know it will fail later.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2024-04-12 18:20:52 +02:00
Olliver Schinagl
ed896c32b0 scripts/kernel_bump: Improve omitted version error
If a version string was not supplied, we currently print an empty
string. We can do better here. Also by popular demand, print the usage
information in case of error.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2024-04-12 18:20:52 +02:00
Olliver Schinagl
03f2f530a0 scripts/kernel_bump: Always drop v prefix
Naivly and lazyly the leading v was only dropped from optarg, not from any
environment variable.

Lets do this properly and ensure a leading 'v' is always dropped.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2024-04-12 18:20:52 +02:00
Olliver Schinagl
1bbc249266 scripts/kernel_bump: Drop unused function
No need to keep unused empty functions. A left over from early development.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2024-04-12 18:20:52 +02:00
Olliver Schinagl
7b7f170216 scripts/kernel_bump: Avoid potential copyright claim
Due to potential fears of copyright infringement noted by Elliott
Mitchell [0], rewrite our message to belong to OpenWRT.

Note, AI was used to aid in construction of this sentence.

[0]: https://lists.openwrt.org/pipermail/openwrt-devel/2024-March/042422.html

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2024-04-12 18:20:52 +02:00
Paul Donald
ae192c042c
mediatek: mt7622: rtl8367c: source code spell fixes
Improves indexing and searches

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
2024-04-12 14:46:32 +02:00
Paul Donald
81e4aabac3
mediatek: mt7622: rtl8367c: source comment fixes
Fix also some Chinese -> UTF8 encoding problems

Improves indexing and searches

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
2024-04-12 14:46:32 +02:00
Paul Donald
90488d274e
mediatek: mt7622: rtl8367c: source comment fixes
Fix also some Chinese GB18030 -> UTF-8 encoding problems

(translated the Chinese strings to English):
修改 -> modification
port8~port10的设置在另外一个register ->
 port8~port10 setup is done in a separate register


You are in the correct (UTF-8) encoding when you see:
 * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
e.g. week 3, 08 third month, 2017
But not if you see:
 * $Date: 2017-03-08 15:13:58 +0800 (閫变笁, 08 涓夋湀 2017) $


rtl8367c/rtl8367c_asicdrv_lut.c should be read as UTF-8, despite having
some earlier Chinese text lost to GB18030 encoding.

Improves indexing and searches

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
2024-04-12 14:46:32 +02:00
Paul Donald
afad4e8ab6
mediatek: mt7622: rtl8367c: source comment fixes
Fix also some Chinese -> UTF8 encoding problems

Improves indexing and searches

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
2024-04-12 14:46:32 +02:00
Paul Donald
a2b94afc0d
mediatek: mt7622: rtl8367c: source comment fixes
Improves indexing and searches

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
2024-04-12 14:46:28 +02:00
Paul Donald
50021d3222
lldpd: make management address advertisement controllable
Defaults to off.

Available from >= 0.7.15

These are sent in TLV

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
2024-04-12 13:45:48 +02:00
Paul Donald
4d8f56bd59
lldpd: make capabilities advertisement controllable
Defaults to off.

Only available from >= 1.0.15

These capabilities are sent in TLV.

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
2024-04-12 13:45:48 +02:00
Sean Khan
849ebc905b qualcommax: enhance smp_affinity (log, uci, syntax)
1.) Changed logic of `set_affinity` to now use physical cores rather than
    knowing the bitmask. Rather than having to know a bitmask, users can
    provide a numerical instance of one or more CPU cores
    (numbered 0-63).

    This is done via function `cpus_to_bitmask`.

    Functions Added:

    a.) bitmask_to_cpus - Takes a bitmask of CPUs and returns a
         list of CPU numbers. (i.e. `bitmask_to_cpus "f"` -> 0,1,2,3)

    b.) cpus_to_bitmask - Takes a comma/space or range list of CPUs and returns
         a bitmask.

         Example:
         `cpus_to_bitmask "2,3"`     -> c
         `cpus_to_bitmask "0,1,2,3"` -> f
         `cpus_to_bitmask "1,3"`     -> a

         With or without quotes
         `cpus_to_bitmask "1 3"`     -> a
         `cpus_to_bitmask  1 3`      -> a

2.) Added UCI options:

    enable     - to enable/disable the script from running.   [default 1 (on)]
    enable_log - to enable/disable logging output to `logger`.[default 1 (on)]

    Log output:
```
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(87) reo2host-destination-ring1    to CPU 0
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(88) reo2host-destination-ring2    to CPU 1
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(89) reo2host-destination-ring3    to CPU 2
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(90) reo2host-destination-ring4    to CPU 3
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(79) wbm2host-tx-completions-ring1 to CPU 1
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(83) wbm2host-tx-completions-ring2 to CPU 2
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(85) wbm2host-tx-completions-ring3 to CPU 3
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(73) ppdu-end-interrupts-mac1      to CPU 1
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(77) ppdu-end-interrupts-mac2      to CPU 2
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(75) ppdu-end-interrupts-mac3      to CPU 3
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(32) edma_txcmpl                   to CPU 3
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(33) edma_rxfill                   to CPU 3
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(35) edma_rxdesc                   to CPU 3
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(36) edma_misc                     to CPU 3
```

    Output of `/proc/interrupts`:
```
 69:          0          0          0          0 GIC-0 209 Edge      rxdma2host-destination-ring-mac1
 70:          0          0          0          0 GIC-0 211 Edge      rxdma2host-destination-ring-mac3
 71:          0          0          0          0 GIC-0 210 Edge      rxdma2host-destination-ring-mac2
 72:       2435          0          0          0 GIC-0 321 Edge      reo2host-status
 73:     268427       8011          0          0 GIC-0 261 Edge      ppdu-end-interrupts-mac1
 74:          2          0          0          0 GIC-0 255 Edge      rxdma2host-monitor-status-ring-mac1
 75:     176169          0          4      10035 GIC-0 263 Edge      ppdu-end-interrupts-mac3
 76:          2          0          0          0 GIC-0 260 Edge      rxdma2host-monitor-status-ring-mac3
 77:          0          0          0          0 GIC-0 262 Edge      ppdu-end-interrupts-mac2
 78:          0          0          0          0 GIC-0 256 Edge      rxdma2host-monitor-status-ring-mac2
 79:       3428       3123          0          0 GIC-0 189 Edge      wbm2host-tx-completions-ring1
 80:          0          0          0          0 GIC-0 323 Edge      reo2ost-exception
 81:        178          0          0          0 GIC-0 322 Edge      wbm2host-rx-release
 82:          0          0          0          0 GIC-0 212 Edge      host2rxdma-host-buf-ring-mac1
 83:       6524          0      13712          0 GIC-0 190 Edge      wbm2host-tx-completions-ring2
 84:          4          0          0          0 GIC-0 235 Edge      host2rxdma-host-buf-ring-mac3
 85:        560          0          0       1979 GIC-0 191 Edge      wbm2host-tx-completions-ring3
 86:          0          0          0          0 GIC-0 215 Edge      host2rxdma-host-buf-ring-mac2
 87:       4520          0          0          0 GIC-0 267 Edge      reo2host-destination-ring1
 88:       2231       2811          0          0 GIC-0 268 Edge      reo2host-destination-ring2
 89:       2180          0       2512          0 GIC-0 271 Edge      reo2host-destination-ring3
 90:       1990          0          0       2321 GIC-0 320 Edge      reo2host-destination-ring4
```

3.) Added `uci-defaults` script `15_smp_affinity` to configure defaults
    options on first boot.

Signed-off-by: Sean Khan <datapronix@protonmail.com>
2024-04-12 13:22:12 +02:00
Paul Donald
b476917502
lldpd: note about capabilities
only available from >= 1.0.15

Comments are useful. Apparently this config parameter was committed when
openwrt used an older version of lldpd which did not yet support it.

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
2024-04-12 13:20:40 +02:00
Paul Donald
8cf1dce428
lldpd: fix restart
Redirection broke in 5364fe0f01 ("lldpd: shellcheck fixes")

redirects to /dev/null shall be handled correctly (i.e. last).

This fixes these errors on `/etc/init.d/lldpd reload`:

2024-03-16T20:39:00 [WARN/lldpctl] unknown command from argument 1: `/dev/null`
2024-03-16T20:39:00 [WARN/lldpctl] unknown command from argument 1: `/dev/null`
2024-03-16T20:39:00 [WARN/lldpctl] unknown command from argument 1: `/dev/null`
2024-03-16T20:39:00 [WARN/lldpctl] unknown command from argument 1: `/dev/null`

Tested-on: 22.03.6
Fixes: 5364fe0f01 ("lldpd: shellcheck fixes")
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
[ improve commit description, add fixes tag ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-04-12 13:20:06 +02:00
Daniel Golle
07918e6612 package: kernel: leds-gca230718: fix build with Linux 6.6
Starting with Linux 6.3 the .probe call no longer got the id parameter,
see also commit torvalds/linux@03c835f498
("i2c: Switch .probe() to not take an id parameter").

As the parameter is anyway unused by the driver, drop it when
building the GCA230718 LED driver for newer kernels.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-04-12 02:07:30 +01:00
Robert Marko
076f945dfb qualcommax: drop 6.1 support
We have defaulted to 6.6 for a while so its time to completely drop 6.1
so new devices dont have to include patches for 6.1.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-04-11 17:26:47 +02:00
Robert Marko
923d7c5531
mediatek: filogic: add support for Edgecore EAP111
HW specifications:
* Mediatek MT7981A
* 256MB SPI-NAND
* 512MB DRAM
* Uplink: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 with 802.3at
PoE (Built-in GBe PHY)
* LAN: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 (Airoha EN8801SC)
* 1 Tricolor LED
* Reset button
* 12V/2.0A DC input

Installation:
Board comes with OpenWifi/TIP which is OpenWrt based, so sysupgrade can
be used directly over SSH.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2024-04-11 13:25:11 +02:00
Robert Marko
2dba4308d1
mediatek: add Airoha EN8801SC PHY driver
Airoha EN8801SC PHY is a gigabit PHY used on Edgecore EAP111 so, include
the MTK driver with some cleanups.

Unfortunatelly, there is no specification sheet nor datasheet available
in order to demistify the magic PBUS writes and work on upstreaming
this driver.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2024-04-11 13:10:15 +02:00
Daniel Golle
98f9154316 generic: 6.1, 6.6: import two pending patches for mt7530 DSA driver
First patch allows to inquire and modify Energy-Efficient-Ethernet
(EEE) settings via ethtool and thereby override the default setting of
a board done via bootstrap pins.

The second patch fixes a long-standing issue with STP (and similar
protocols) when using boards (or SoCs) governed by the mt7530 DSA
driver.

Both patches could also be (dirty-)applied to Linux 5.15, but I'd
rather just wait for that to happen via linux-stable to avoid the
mess.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-04-10 18:50:32 +01:00
Daniel Golle
4354b34f6f generic: 6.6: sync mt7530 DSA driver with upstream
Backport lots upstream changes, many of them fixes, for the mt7530 DSA
driver, similar to how it was done for Linux 6.1 in the previous commit.

The remaining differences compared to the upstream driver are only
the 'slave' -> 'user', 'master' -> 'conduit' language change in DSA
and the rename of 'struct ethtool_eee' to 'struct ethtool_keee' as
well as tree-wide replacement of ethtool_sprintf with ethtool_puts,
all of them do not have any functional impact.

Apart from some minor bug fixes and style improvements the switch
should now behave more conformant when it comes to link-local frames,
and we will again be able to cleanly pick patches from upstream.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-04-10 18:50:32 +01:00
Daniel Golle
401a6ccfaf generic: 6.1: sync mt7530 DSA driver with upstream
Backport lots upstream changes, many of them fixes, for the mt7530 DSA
driver. Some of them may or may not find they way into Linux 6.1
stable, some certainly won't because they are fixes for backported
commits which aren't even present in Linux 6.1 upstream.

Apart from adding new patches, also remove mutated patch
723-net-mt7531-ensure-all-MACs-are-powered-down-before-r.patch
which should never have been added for Linux 6.1 -- it was applied
already upstream but coincidentally would fuzzy-apply in the wrong
place as well (for MT7530 instead of MT7531). While that didn't really
hurt anyone it is just unneeded.

The other deleted patch
795-mt7530-register-OF-node-for-internal-MDIO-bus.patch
has been replaced by an equivalent commit with a more complete patch
description by upstream maintainer Arınç Ünal.

The remaining differences compared to the upstream driver are:
 * C22/C45 MDIO ops aren't split
   Upstream did that, backporting it would require making changes to
   *all* DSA drivers
 * 'slave' -> 'user', 'master' -> 'conduit' language change in DSA
 * support for selecting preferred CPU port on MT7531
   Also this would require too many DSA framework changes potentially
   affecting other devices. If we ever really use Linux 6.1 in a
   release (I hope not) we can still reconsider to make the effort to
   backport that.

In addition to some minor bug fixes and style improvements the switch
should now behave more conformant when it comes to link-local frames,
and we will again be able to cleanly pick patches from upstream.

MAINTAIERS NOTE:
Three patches are already part of Linux stable and should be removed with
the next minor kernel version bump:
789-STABLE-01-net-dsa-mt7530-prevent-possible-incorrect-XTAL-frequ.patch
789-STABLE-02-net-dsa-mt7530-fix-link-local-frames-that-ingress-vl.patch
789-STABLE-03-net-dsa-mt7530-fix-handling-of-all-link-local-frames.patch

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-04-10 18:50:32 +01:00
Oleg S
d668c74fe6 kernel: add kmod-hwmon-emc2305 support
This module supports the Microchip Technology Inc (SMSC)
EMC2301/EMC2302/EMC2303/EMC2305 fan speed PWM controller chips.

Signed-off-by: Oleg S <remittor@gmail.com>
2024-04-10 10:50:17 +02:00
Felix Fietkau
08639a5e47 ucode: update to Git HEAD (2024-04-07)
1220992631d5 ubus: automatically clear error information
d6fd94014eea uci: automatically clear error information
99837f280b61 uloop: automatically clear error information
be767ae197ba vm: rework `in` operator semantics
4ade84e8fb81 ubus: add explicit support for deferring incoming requests

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-04-09 21:33:02 +02:00
Robert Marko
12b2cb2ec3 config: fix CONFIG_GDB appearing in main menuconfig menu
I noticed that CONFIG_GDB was suddenly appearing in the main menuconfig
menu despite the fact that it should be visible only when TOOLCHAINOPTS
is selected and under a dedicated menu.

After some trial and error, it seems that this was caused by the recent
addition of GCC_USE_DEFAULT_VERSION, and after even more trial and error
it gets fixed as soon GCC_USE_DEFAULT_VERSION is placed after GCC_VERSION.

So, lets simply put GCC_USE_DEFAULT_VERSION after GCC_VERSION.

Fixes: 501ef81040 ("config: select KERNEL_WERROR if building with default GCC version")
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-04-09 19:30:41 +02:00
Daniel Golle
a68eb99191 generic: add missing patch headers
Make sure all patches can be applied to a git tree using 'git am'
by adding missing patch headers where needed.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-04-09 17:54:08 +01:00
Robert Marko
e65800d948 tools: zstd: dont override CLI max level
Now that instead of relying on env variables for the GH download script
invoking ZSTD tarball compression it passes the full arguments via tar -I
we can drop the CLI max compression level override.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-04-09 18:39:36 +02:00
Robert Marko
204823ac28 scripts/dl_github_archive: use tar -I for ZSTD
Instead of relying on env variables for setting the ZSTD compression
configuration we can simply do what we do for IB, SDK and the rest and
use tar -I to pass "zstd -T0 --ultra -20" directly.

This makes it rather clear what is being done and allows to drop the
zstd CLI max level override as its usually capped at level 19.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-04-09 18:39:36 +02:00
Daniel Golle
1ae3c53466 mediatek: filogic: switch TP-LINK XDR series to fitblk
Instead of using the deprecated FIT partition parser, use the new
fitblk driver instead.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-04-09 15:07:41 +01:00
Daniel Golle
d4e8653e1e mvebu: puzzle-m90x: wipe rootfs_data on sysupgrade
The sysupgrade formware of the Puzzle series is a slightly strange
dual-boot approach while remaining compatible with Marvell's SDK
firmware upgrade binary format -- which happens to be a full-disk
image with GPT partition table. Hence that /lib/upgrade/emmc-puzzle.sh
script is like an exotic disease which results from those decisions,
and as we also want to somehow stay compatible with the IEI-World
stock firmware we got to use it in that same way (we are not
compatible with the QNAP-branded identical hardware device anyway).

Currently, on sysupgrade the result is that one ends up with the old
content of rootfs_data (a GPT partition on those devices) as nothing
ever wipes or in any way re-creates the filesystem there. As a simple
work-around, let's kill the filesystem on rootfs_data so fstools
re-formats it on the next boot.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-04-09 14:59:03 +01:00
Robert Marko
7c39a95a2f sdk: include lib/crtsavres.o for powerpc
Trying to link certain kernel modules like dahdi-linux when building with
the OpenWrt SDK will fail with:
openwrt-sdk-apm821xx-sata_gcc-13.2.0_musl.Linux-x86_64/staging_dir/toolchain-powerpc_464fp_gcc-13.2.0_musl/bin/powerpc-openwrt-linux-musl-ld: cannot find arch/powerpc/lib/crtsavres.o: No such file or directory

Previously this worked with the PowerPC SDK since we carried a hack that
was passing --save-restore-funcs to module LDFLAGS so the linker provided
the required functions automatically as without --save-restore-funcs it
doesnt do so automatically on relocatable links and as a sideffect did not
require the kernel provided crtsaves.o to link against.

Now that hack has been removed as upstream kernel now compiles crtsaves.o
by default so it can be linked against but its not included in the SDK.

So, lets include lib/crtsavres.o when SDK is generated for PowerPC.

Fixes: 99c9d8abd6 ("kernel: bump 5.15 to 5.15.148")
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-04-09 11:13:18 +02:00