The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Failsafe code of dropbear should be in the dropbear package not the
base-files package.
Signed-off-by: Kyle Copperfield <kmcopper@danwin1210.me>
Setting CONFIG_IPK_FILES_CHECKSUMS=y causes sha256 checksum files to be
included with the packages to check for corruption. This commit fixes two
issues:
- /sbin/pkg_check was being removed incorrectly if IPK_FILES_CHECKSUMS=y
- checksums were being saved in the wrong file
Signed-off-by: Xu Wang <xwang1498@gmx.com>
With this change the well known jshn library will be used, to build the
json arguments for the ubus sysupgrade method. This is also used in all
other shell program that uses JSON. This commit unifies that.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The preinit network initialisation and failsafe informational message
are inherently racy as the interface takes some time to become
functional after "ip link set $pi_ifname up" command.
Consider this timing:
[ 12.002713] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 12.008819] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
[ 12.118877] random: procd: uninitialized urandom read (4 bytes read)
[ 13.068614] eth1: link up (1000Mbps/Full duplex)
[ 13.073309] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 13.080445] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.1: link becomes ready
Since the UDP message was sent prior to link becoming ready, it was
never seen on the wire.
The default failsafe timeout is set to 2 seconds, so with this patch
there are two attempts to send the message, one spent in vain, and the
other visible in tcpdump on an attached host. Of course, in cases when
the interface is brought up faster it leads to two messages, however it
should be harmless. This patch (almost) doesn't affect normal boot time
while still allowing to enter failsafe reliably with a single button
press, matching the official "generic failsafe" documentation.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
netifd does not handle network.@device[x].name properly if it
contains multiple ifaces separated by spaces. Due to this, board.d
lan_mac setup does not work if multiple ifaces are set to LAN by
ucidef_set_interface_lan.
To fix this, create a device node for each member iface when
running config_generate instead. Those are named based on the
member ifname:
ucidef_set_interface_lan "eth0 eth1.1"
ucidef_set_interface_macaddr "lan" "yy:yy:yy:yy:yy:01"
will return
config device 'lan_eth0_dev'
option name 'eth0'
option macaddr 'yy:yy:yy:yy:yy:01'
config device 'lan_eth1_1_dev'
option name 'eth1.1'
option macaddr 'yy:yy:yy:yy:yy:01'
ref: https://github.com/openwrt/openwrt/pull/2542
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[always use new scheme, extend description, change commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Commit ed5b9129d7 ("base-files: implement generic service_running")
has added EXTRA_HELP variable, thus overriding already available
EXTRA_HELP text available in other init scripts, resulting in the
missing help text from services like dropbear for example.
So fix this regression by appending EXTRA_HELP text provided by the
other init scripts into the one provided by the script itself.
Fixes: ed5b9129d7 ("base-files: implement generic service_running")
Signed-off-by: Peter Stadler <peter.stadler@student.uibk.ac.at>
[commit title/description facelift, fixes tag, fixed From:, pkg bump]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Discovered recent changes had broken sysupgrade for ar71xx mikrotik
rb-493g, traced the problem to missing /usr/share/libubox/jshn.sh after
switching to tmpfs.
Signed-off-by: Russell Senior <russell@personaltelco.net>
uci-defaults are sourced and non-executable, so they do not require
a shebang.
While at it, apply consistent naming scheme.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Now that netifd and hostapd allow dynamic reconfiguration, add a
command to trigger it.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit 6170c46b47.
There has been demand for further evaluation of the impact of a
changed hostname, so this is reverted for now. The default hostname
will be "OpenWrt" again after this commit.
The macaddr_geteui() function is not removed by this revert.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
If a label MAC address is provided for device, system
will rename the hostname with OpenWrt_{eui mac address}.
This helps to distinguish between different devices.
Since it's no good idea to nest json_* functions, this code does
not use get_mac_label directly, but only get_mac_label_dt as
external resource.
Signed-off-by: Rosy Song <rosysong@rosinson.com>
[merged with commit introducing macaddr_geteui, rebased on updated
label MAC address storage, extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
If set, label MAC address is available from one of two sources,
device tree or board.json. So far, the function get_mac_label
was meant for retrieving the address, while an option in uci
system config was specified only for case 2 (board.json).
The uci config option has several drawbacks:
- it is only used for a fraction of devices (those not in DT)
- label MAC address is a device property, while config implies
user interaction
- label_macaddr option will only be set if /etc/config/system
does not exist (i.e. only for new installations)
Thus, this patch changes the behavior of get_mac_label:
Instead of writing the value in board.json to uci system config
and reading from this location afterwards, get_mac_label now
extracts data from board.json directly. The uci config option
won't be used anymore.
In addition, two utility functions for extraction only from DT
or from board.json are introduced.
Since this is only changing the access to the label MAC address, it
won't interfere with the addresses stored in the code base so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"block mount" invokes "hotplug-call mount". It emits the following
error when mount is not present
hotplug-call call failed
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Moving a file between tmpfs and other fs is neither
faster nor safer, thus no point in doing it in two steps.
Use new jshn option to write output directly to file.
Originally discussed here:
http://lists.openwrt.org/pipermail/openwrt-devel/2017-December/010127.html
Signed-off-by: Roman Yeryomin <roman@advem.lv>
This separates the options for signature creation and verification
* SIGNED_PACKAGES create Packages.sig
* SIGNED_IMAGES add ucert signature to created images
* CHECK_SIGNATURE add verification capabilities to images
* INSTALL_LOCAL_KEY add local key-build to /etc/opkg/keys
Right now the buildbot.git contains some hacks to create images that
have signature verification capabilities while not storing private keys
on buildbot slaves. This commit allows to disable these steps for the
buildbots and only perform signing on the master.
Signed-off-by: Paul Spooren <mail@aparcar.org>
While all ath10k eeproms have a checksum field, so far two
functions for patching ath10k MAC address have been present (and
been used).
This merges code to provide a single function ath10k_patch_mac
in caldata.sh, having its name in accordance with ath9k functions.
By doing so, correct MAC patching for current and future ath10k
devices should be ensured.
This patch adds checksum adjustments for several targets on
ath79 and lantiq.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This unifies MAC address patch functions and moves them to a
common script. While those were implemented differently for
different targets, they all seem to do the same. The number of
different variants is significantly reduced by this patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the almost identical calibration data extraction
functions present multiple times in several targets to a single
library file /lib/functions/caldata.sh.
Functions are renamed with more generic names to merge different
variants that only differ in their names.
Most of the targets used find_mtd_chardev, while some used
find_mtd_part inside the extraction code. To merge them, the more
abundant version with find_mtd_chardev is used in the common code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[rebase on latest master; add mpc85xx]
Signed-off-by: David Bauer <mail@david-bauer.net>
The xor() function is defined in each of the caldata extraction
scripts for several targets. Move it to functions.sh to reduce
duplicate code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"coreutil-date" package from the packages feed replaces the Busybox date
applet by symlinking /usr/bin/gnu-date to /bin/date. This prevents the system
init script from setting kernel timezone because the GNU date utility does not
provide such functionality:
root@OpenWrt:~# date -k
date: invalid option -- 'k'
Try 'date --help' for more information.
A specific reference to the Busybox date applet prevents alternative date
utilities from breaking the system init script.
Signed-off-by: Val Kulkov <val.kulkov@gmail.com>
The factory uboot of the Turris Omnia boots with "root=b301", and we
instruct new users to sysupgrade from there (e.g. method 1, step 7).
Currently, this will fail with "Unable to determine upgrade device".
Add a new case to export_bootdevice, which parses the hex argument.
Fixes commit 2e5a0b81 ("mvebu: sysupgrade: sdcard: keep user added ...")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
For many devices, MAC addresses cannot be retrieved via the
device tree alias.
To still provide the label MAC address for those, this implements
a second mechanism that will put the address into uci config.
Note that this stores the actual MAC address, whereas in DTS
we reference the bearing device.
This is based on the work of Rosy Song <rosysong@rosinson.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
To refer to the MAC address on a device's label, one can
specify the alias label-mac-device in the DTS which should
point to the bearer of the corresponding MAC address.
With the function get_mac_label, the user can retrieve then
retrieve this address and use it as a value that uniquely
identifies his device.
This is severely helpful for several downstream functionalities,
e.g. define MAC addresses of custom netifs or change the SSID to
be easily recognizable.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adds a default status action for init.d scripts.
procd "service status" will return:
0) for loaded services (even if disabled by conf or dead)
3) for inactive services
4) when filtering a non-existing instance
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
[rebased, cleaned up]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Now that $UPGRADE_BACKUP is set conditionally there is no need to check
the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This explicitly tells procd what backup file should be used during
sysupgrade (if any). It's much more generic this way compared to the
magic /tmp/sysupgrade.tgz file that had to be created before a call.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This allows platform code to check if firmware image can be used with
preserving a backup. It may be used e.g. when installing vendor
firmwares that won't restore appended backup archive.
Suggested-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's a variable set by procd that should replace hardcoded
/tmp/sysupgrade.tgz.
This change requires the most recent procd with the commit 0f3c136
("sysupgrade: set UPGRADE_BACKUP env variable").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The actual retrieval of the MAC address in mtd_get_mac_binary_ubi()
is the same as in get_mac_binary(). Thus, use the latter function
in the former to reduce duplicate code.
This will also allow to benefit from the enhanced path check there
and bring mtd_get_mac_binary_ubi() more in line with the similar
mtd_get_mac_binary().
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The mtd_get_mac_text helper method did not support hexadecimal offset
values, resulting them to break after 75bfc393ba ("treewide:
convert MAC address location offsets to hexadecimal")
This commit fixes this by evaluating the hexadecimal input,
converting them to decimal.
Signed-off-by: David Bauer <mail@david-bauer.net>
1) Add BACKUP_FILE and use it when copying an archive to be restored
after sysupgrade (on the next preinit).
2) Use CONF_TAR for copying backup prepared by the /sbin/sysupgrade
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
So far firmware validation result was binary limited: it was either
successful or not. That meant various limitations, e.g.:
1) Lack of proper feedback on validation problems
2) No way of marking firmware as totally broken (impossible to install)
This change introduces JSON for storing detailed validation info. It
provides a list of performed validation tests and their results. It
allows marking firmware as non-forceable (broken image that can't be
even forced to install).
Example:
{
"tests": {
"fwtool_signature": true,
"fwtool_device_match": true
},
"valid": true,
"forceable": true
}
Implementation is based on *internal* check_image bash script that:
1) Uses existing validation functions
2) Provides helpers for setting extra validation info
This allows e.g. platform_check_image() to call notify_check_broken()
when needed & prevent user from bricking a device.
Right now the new JSON info is used by /sbin/sysupgrade only. It still
doesn't make use of "forceable" as that is planned for later
development.
Further plans for this feature are:
1) Expose firmware validation using some new ubus method
2) Move validation step from /sbin/sysupgrade into "sysupgrade" ubus
method so:
a) It's possible to safely sysupgrade using ubus only
b) /sbin/sysupgrade can be more like just a CLI
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This explicitly lets stage2 know if partitions should be preserved. No
more "touch /tmp/sysupgrade.always.overwrite.bootdisk.partmap" hack.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
generate feeds.buildinfo and version.buildinfo in build dir after
containing the feed revisions (via ./scripts/feeds list -sf) as well as
the current revision of buildroot (via ./scripts/getver.sh).
With this information it should be possible to reproduce any build,
especially the release builds.
Usage would be to move feeds.buildinfo to feeds.conf and git checkout the
revision hash of version.buildinfo.
Content of feeds.buildinfo would look similar to this:
src-git routing https://git.openwrt.org/feed/routing.git^bf475d6
src-git telephony https://git.openwrt.org/feed/telephony.git^470eb8e
...
Content of version.buildinfo would look similar to this:
r10203+1-c12bd3a21b
Without the exact feed revision it is not possible to determine
installed package versions.
Also rename config.seed to config.buildinfo to follow the recommended
style of https://reproducible-builds.org/docs/recording/
Signed-off-by: Paul Spooren <mail@aparcar.org>
do_upgrade_stage2() isn't really any common code. It isn't used anywhere
except for /sbin/sysupgrade that passes it to the stage2.
Moving its code to separated file also simplifies COMMAND variable.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Logic was inverted when changing from string check to file check.
Fix it.
Fixes: 8592602d0a ("base-files: Really check path in get_mac_binary")
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
With bcm53xx switched to the new procedure there is no more need for
keeping that backward compatibility code.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Its last usage was dropped back in 2013 in the commit b95bdc8ab5
("kernel/base-files: clean up old code related to refreshing mtd
partitions, it is no longer used anywhere").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Currently, path argument is only checked for being not empty.
This changes behavior to actually check whether path exists.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Restart is in default implemented so it calls stop and start. This is
pretty unsafe to call on umount service. This service should not do
anything on restart the same way as on start. Only use of this service
is on stop.
Signed-off-by: Karel Kočí <cynerd@email.cz>
Just stumbled across this LEDE legacy, without finding any real reason
to keep it. There is a single LEDE_DEVICE_MANUFACTURER_URL dependency
in the luci feed repo which needs to be syncronized.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
[re-added missing commit message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch is in a series to allow additional STOP indexes after umount,
so that other block devices may stop cleanly.
boot is now STOP=90
umount is now STOP=90
After this patch series, the resulting STOP indexes in the 80s & 90s
will be:
STOP=85 odhcpd.init
STOP=89 conntrackd.init
STOP=89 log.init
STOP=89 rssileds.init
STOP=90 boot
STOP=90 kdump.init
STOP=90 network
STOP=90 sysfixtime
STOP=90 umount
STOP=98 mdadm.init (note: will be addressed in a separate patch)
Signed-off-by: Joseph Tingiris <joseph.tingiris@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[PKG_RELEASE is now 200]
This is mainly for kmod-br-netfilter. To turn off
bridge-netfilter-call-xxx immediately after installation
While at it
- Define filelist="/usr/lib/opkg/info/${pkgname}.list"
- Reuse "[ -z "$root" ]"
- Grep with "-m1"
Fixes FS#2300
Reported-by: Marco Sartorius <tidbits@ormoorgmen.info>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This patch adds a missing type property. This fixes
the creation of oneshot and timer led triggers like:
| ucidef_set_led_timer "system" "system" "zhuotk:green:system" "1000" "1000"
from /etc/init.d/01_leds.
Fixes: b06a286a48 ("base-files: cleanup led functions in uci-defaults.sh")
Signed-off-by: Robinson Wu <wurobinson@qq.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
For devices such as BTHOMEHUBV5A with both reset and restart buttons,
its easily accessible restart button has been assigned to KEY_POWER
power script to poweroff preventing accidental (or malicious) factory
resets by KEY_RESTART reset script. However an easily accessible button
immediately powering off the device is also undesirable.
Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
Commit "generic: ar8216: add mib_poll_interval switch attribute" has
added mib_poll_interval global config option and commit "generic:
ar8216: group MIB counters and use two basic ones only by default" has
added mib_type config option.
So this patch adds ucidef_set_ar8xxx_switch_mib helper function which
would allow configuration of the above mentioned new switch config
options.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Recently, upgrade device autodetection has been added to the mvebu target.
This exposes some shortcomings of the generic export_bootdevice function,
e.g. on the Turris Omnia: export_bootdevice silently reports the root
partition to be the boot device. This makes the sysupgrade process fail at
several places.
Fix this by clearly distinguishing between /proc/cmdline arguments which
specify the boot disk, and those which specify the root partition. Only in
the latter case, strip off the partition, and do it consistently.
root=PARTUUID=<pseudo PARTUUID for MBR> (any partition) and root=/dev/*
(any partition) are accepted.
The root of the problem is that the *existing* export_bootdevice in
/lib/upgrade/common.sh behaves differently, if the kernel is booted with
root=/dev/..., or if it is booted with root=PARTUUID=...
In the former case, it reports back major/minor of the root partition,
in the latter case it reports back major/minor of the complete boot disk.
Targets, which boot with root=/dev/... *and* use export_bootdevice /
export_partdevice, have added workarounds to this behaviour, by specifying
*negative* increments to the export_partdevice function.
Consequently, those targets have to be adapted to use positive increments,
otherwise they are broken by the change to export_bootdevice.
Fixes: 4e8345ff68 ("mvebu: base-files: autodetect upgrade device")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Purpose of these changes is to introduce a hook for post service
shutdown in a similar fashion to the existing hook service_started. I
found it to be useful to specify a hook that is called once the service
has been stopped and not before the service is stopped like the
stop_service hook does.
The concrete use case I have for this is that I'm running a binary that
takes over the hardware watchdog timer. Said binary unfortunately can
not use ubus directly to tell procd to hand over the watchdog timer so
this has to be done in the service file for the binary in question. In
order to support a clean handover of the watchdog timer back to procd,
the service init script has to dispatch the ubus invocation once the
binary in question has been stopped.
Signed-off-by: Arthur Skowronek <ags@digineo.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[added commit message, use the same form as other hooks]
Currently leds migration scripts in ar71xx and lantiq share a lot of
logic and introducing leds migration to another target would mean
copying this code, again. Therefore add common logic to library in
base-files package.
Suggested-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Commit 124ab1dc0a and 5523ee3459 introduced the assignment of the
group "tty" to /dev/tty* devices in order to support unprivileged
user access to serial devices.
However, due to an improperly rebased commit this feature broke.
This patch restores the lost hunk in hotplug.json file to
re-introduce this feature and also renames the existing "tty" group
to "dialout" as this is the more typical name for such a group
on desktop systems.
Fixes: 5209cfa534 ("procd: fix hotplug.json syntax")
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Jo-Philipp Wich <jo@mein.io>
ucert needs to check the firmware part with metadata, but without the signature.
Use the new fwtool mode to extract that without altering the firmware image inside
the check
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When config_get is called as "config_get section option" the option
is unexpectedly globbed by the shell which differs from the way options
are read to a variable with "config_get variable section option".
Add another layer of double quotes to fix it.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
Add support for passing additional parameters to mtd called during
sysupgrade. It will be required to toggle the "recovery moe" flag
supported by recent tp-link boards.
Signed-off-by: David Bauer <mail@david-bauer.net>
[split code from board support patch; add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This may be useful if you don't entirely trust your flash and want to be able
to check for corruptions.
Signed-off-by: Michal Hrusecky <Michal@Hrusecky.net>
This adds a wrapper (uci_load_validate) for uci_validate_section() that
allows callers (through a callback function) to access the values set by
uci_validate_section(), without having to manually declare a
(potentially long) list of local variables.
The callback function receives two arguments when called, the config
section name and the return value of uci_validate_section().
If no callback function is given, then the wrapper exits with the value
returned by uci_validate_section().
This also updates several init scripts to use the new wrapper function.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
This commit allows to use non-standard UBI volume name as the rootfs
volume in sysupgrade.
ex.:
The U-Boot on Buffalo WXR-2533DHP checks existence and checksum of
"ubi_rootfs" volume when booting, so this name is required.
OpenWrt currently provides several patches:
490-ubi-auto-attach-mtd-device-named-ubi-or-data-on-boot.patch
491-ubi-auto-create-ubiblock-device-for-rootfs.patch
492-try-auto-mounting-ubi0-rootfs-in-init-do_mounts.c.patch
to facilitate ubi rootfs automount. However the upstream kernel
also supports the means of booting from a fully custom ubi
partition name and ubi volume name via bootargs/kernel's cmdline
parameters:
ubi.mtd=mtd_partition_name
ubi.block=rootfs_volume_name
root=/dev/ubiblock$X_$Y
For more information and examples visit the wiki over at linux-mtd:
<http://www.linux-mtd.infradead.org/faq/ubifs.html>
<http://www.linux-mtd.infradead.org/doc/ubi.html>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
This file is needed to properly use the tc ematch modules present in
kmod-sched-core and kmod-sched. It is a read-only index file of ematch
methods used only by tc.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
In the upstream netdev led trigger the one mode file was replaced by 3
files named rx, tx and link. Fix the netdev trigger configuration code
to use the modified API.
Fixes: aa3b6a08c5 ("kernel: Replace ledtrig-netdev with upstream backport")
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When '-k' is used, sysupgrade inserts into backup a new file
/etc/backup/installed_packages.txt which contains pkgname and origin (rom,
overlay, unknown) without touching rootfs.
It's mainly used to reinstall all extra packages:
# opkg update
# grep "\toverlay" /etc/backup/installed_packages.txt | cut -f1 | xargs -r opkg install
# rm /etc/backup/installed_packages.txt
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Add sysupgrade '-o' option in order to include all overlay files in
backup, except for those that are from packages but including files
listed in conffiles, sysupgrade.conf or /lib/upgrade/keep.d.
With '-u' option, it will skip files equals to /rom and conffiles that
were not changed.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
With '-u', for a file /aaa/bbb/ccc enlisted for backup,
it will only get into backup if /rom/aaa/bbb/ccc does not
exist or /aaa/bbb/ccc is different from /rom/aaa/bbb/ccc.
It also works with '-c', but only effective for files touched
but not modified.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Renamed add_uci_conffiles to add_conffiles as it includes
any conffiles listed, not only UCI ones.
Make do_save_conffiles arg mandatory
Allow other options after -l (like -c)
Do not use stdout for error messages (fixes backup to stdout)
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
I wanted to add status LEDs support to my imx6 based board and have
found out, that I could use diag.sh script found in ramips platform,
which seems to be also shared in a few other platforms:
4801276bc2078c5bcf03003c831e3b0a target/linux/ramips/base-files/etc/diag.sh
4801276bc2078c5bcf03003c831e3b0a target/linux/ipq40xx/base-files/etc/diag.sh
4801276bc2078c5bcf03003c831e3b0a target/linux/ath79/base-files/etc/diag.sh
So I've extended the base diag.sh in a way, that if it detects any of
the DTS LED aliases, then it would use the generic DTS set_led_state
code.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This reverts commit 41770add03.
The fwtool_check_image() procedure is used by `sysupgrade --test` which must
not alter the image under test in any way.
Currently, when the LuCI ui or any other sysupgrade wrapper first invokes
sysupgrade --test to verify the compatibility of the image and then calculates
the sha256sum over it, the resulting checksum will differ from the original
image since the test invocation will implicitely strip the metadata trailer.
To properly fix the underlying issue, the combined image checksumming code
must be modified to skip the metadata trailer.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The return value of a package prerm script is discarded and not returned
correctly by default_prerm(). This allows other operations like service
shutdown to "leak" their return value, prompting workarounds like commit
48cfc826 which do not address the root cause.
Preserve a package prerm script return value for use by default_prerm(),
sharing the corresponding code from default_postinst() for consistency.
Also use consistent code for handling of /etc/init.d/ scripts.
Run Tested on: LEDE 17.01.4 running ar71xx.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
If I create following image:
define Device/engenius-m36
IMAGE/sysupgrade.bin := combined-image | append-metadata
endef
Sysupgrade then errors out:
Invalid image. Contents do not match checksum (image:cd285595eaf297370404ae0e2815ec1a calculated:2cf9a2286fb6b01af3ea189128017d44)
Image check 'platform_check_image' failed.
By removing the metadata from the image I get combined-image checksum
working again and sysupgrade works.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
When restart is run on an init script, the script traps SIGTERM. This is
done as a workaround for scripts named the same name as the program they
start. In that case, the init script process will have the same name as
the program process, and so when the init script runs killall, it will
kill itself. So SIGTERM is trapped to make the init script unkillable.
However, the trap is retained when the init script runs start, and thus
processes started by restart will not respond to SIGTERM, and will thus
be unkillable unless you use SIGKILL. This fixes that by removing the
trap before running start.
Signed-off-by: Linus Kardell <linus@telliq.com>
The swconfig switch led driver has the ability to switch
between a "link, rx and/or tx" mode. However, this feature
was not implemented in uci, the led init script and
config_generate.
This patch adds a seventh parameter to the
ucidef_set_led_switch() function. The accepted values for
this parameter are: link, rx and tx.
Any permutations of these three values are supported, as
long as they are properly encased with quotes.
If the parameter is not specified it will default to "all"
(link rx tx).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Commit 7f694582 introduced a bug where default_postinst() often fails to
remove a uci-defaults script after application, leaving it to run again
after a reboot.
(Note: commit 7f694582 also introduced FS#1021, now fixed by 73c745f6)
The subtle problem arises from the shell logical chain:
[ -f "$i" ] && . "$i" && rm -f "$i"
Most uci-defaults scripts contain a terminal 'exit 0' statement which,
when sourced, results in the logic chain exiting before executing 'rm -f'.
This was observed while testing upgrades of 'luci-app-sqm'.
The solution is to wrap the shell sourcing in a subshell relative to the
command 'rm -f':
( [ -f "$i" ] && . "$i" ) && rm -f "$i"
Revert to using 'grep' to prefilter the list of entries from the control
file, which yields the full path of uci-defaults scripts. This allows
keeping the existence check, directory change and script sourcing inside
the subshell, with the script removal correctly outside.
This approach avoids adding a second subshell only around the "." (source)
command. The change also preserves the fix FS#1021, since the full path is
used to source the script, which is POSIX-portable irrespective of PATH
variable or reference to the CWD.
Run Tested on: LEDE 17.01.4 running ar71xx, while tracing installation of
package luci-app-sqm with its associated /etc/uci-defaults/luci-sqm file.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* add missing 'rpcbind' alias to /etc/services
Allows rpcbind to open its 111 port and be reachable via lan, this is the default behaviour.
Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com>
Set the window title not only in "xterm", but also in
e.g. "xterm-256color", "xterm-color", etc.
The case statement is taken from Debian / Ubuntu.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
/etc/ethers is missing on /rom but always created when dnsmasq
runs. It is better to have it in place and avoid an extra change
in flash after firstboot.
It will generate an extra /etc/ethers-opkg when it has changed.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Set the (sys)upgrade state when sourcing the stage2 script instead of
setting the state for each target individual.
This change fixes the, due to a missing state set, not working upgrade
led on ath79 and apm821xx.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add a function to get a mac stored as text from flash. The octets of
the mac address need to be separated by any separator supported by
macaddr_canonicalize().
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the opening bracket right after the function name, to do it the
same way for all functions in this file.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Avoid having /sbin/wifi silently ignore unknown keywords and execute
"up"; instead display the help message and exit with an error.
Spell out the "up" keyword (which has users), add it to usage output,
and preserve the implicit assumption that runing /sbin/wifi without
argument performs "up".
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Verify ucert signature chains in sysupgrade images in case ucert is
installed and $CHECK_IMAGE_SIGNARURE = 1.
Also make sure ucert host binary is present and generate a self-signed
ucert in case $TOPDIR/key-build.ucert is missing.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Sysupgrade shouldn't proceed, if the backup of the configuration
fails because tar (or gzip) exit with a non-zero code.
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
this feature has never worked, the fw image name was not passed and the -t
parameter was missing in the tool invocation. drop the feature.
Signed-off-by: John Crispin <john@phrozen.org>
