Commit Graph

44210 Commits

Author SHA1 Message Date
Chuanhong Guo
d6366ce366 generic: ar8216: mib_work_func: read all port mibs everytime
ar8xxx_mib_capture will update mib counters for all ports. Current
code only update one port at a time and the data for other ports
are lost.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-24 01:44:26 +01:00
Chuanhong Guo
9fc506e9b2 generic: ar8216: add support for get_port_stats()
Partially reverts commit eff3549c58.

AR7240 and AR9341 have buggy hardware switch LED trigger. The AR7240
one doesn't blink and the blinking of port0/port5 is reversed on
AR9341 if we swap PHY0 and PHY4. (Only blinking is reversed, which
means LED for PHY0 will lit when PHY0 is link up and will blink when
PHY4 has active link and vice versa.) On these two chips a software
swconfig LED trigger is required.

This commit adds swconfig port stats back but:
 1. move checking of mib_t/rxb_id into ar8xxx_chip since we can't
    distinguish ar7240sw and ar8216 using only chip id.
 2. don't update mib counter in get_port_stat. This function is called
    every 0.01s and this capturing procedure will take up a lot of CPU.
    We already have a mib_work_func updating mib counters every 2s so
    return the saved counter instead of fetching new data. The blinking
    rate will be weird but it should solve the previously mentioned CPU
    time problem.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-24 01:44:26 +01:00
Chuanhong Guo
0598ec0abc generic: ar8216: add support for ar724x/ar933x builtin switch
This builtin switch is a bugless ar8216 with different mib counters
and gigabit cpu port.
Atheros uses the same device ID and it's impossible to distinguish
the standalone one and the builtin one. So we add support to mdio
device probe only.

This switch doesn't have buggy vlan tag so it's not needed to enable
atheros header. This commit changed ar8216_setup_port so that it can
be reused for this switch.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-24 01:44:26 +01:00
Chuanhong Guo
ad8db1fa2e generic: ar8216: mdiodev: add qca,phy4-mii-enable option
This option allows setting phy4 as a phy connected directly to CPU.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-24 01:44:26 +01:00
Chuanhong Guo
cf9900978a generic: ar8216: ar8229: add phy_read/phy_write
the added function also works for ar8216 and will be used in the
following ar7240 support.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-24 01:44:26 +01:00
Chuanhong Guo
cc817392f4 generic: ar8216: add support for separated mdio bus for phy access
Atheros FE switches have a builtin mdio master available for PHY
accessing and on ar724x/ar933x builtin switches this mdio master
is the only way of accessing PHYs.

After this patch if there is phy_read/phy_write method available
in ar8xxx_chip we register a separated mdio bus for accessing PHYs.

Still adds support for mdio device probing only since this isn't
needed for those switches registered using PHY probing.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-24 01:44:26 +01:00
Chuanhong Guo
cb7d96499c generic: ar8216: add support for ar8229
ar8229 is the builtin switch in ar934x and later chips. There is
also a standalone version available and their registers/functions
are the same.

This commit added support for the builtin ar8229. The only thing
missing for standalone ar8229 should be phy modes. Since I don't
have a router using that, this commit doesn't add support for
other phy modes.

Only add its support for mdio-device probing method because the
current PHY probing can't return 1G speed when it's a FE switch.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-24 01:44:25 +01:00
Chuanhong Guo
7d504f68a6 generic: ar8216: add mdio-device probing support
currently only ar8327 and ar8236 are added since they are the only
two I could verify.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-24 01:44:25 +01:00
Chuanhong Guo
da64a8c656 generic: ar8216: move ar8xxx_id_chip into ar8xxx_phy_probe
ar8xxx_id_chip is used to determine current ar8xxx_chip using switch
id and this isn't needed during mdiodev probing.
Move it out of ar8xxx_probe_switch so that we can skip it.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-24 01:44:25 +01:00
Chuanhong Guo
ebec6c9f85 generic: ar8216: add device struct into struct ar8xxx_priv
dev has been taken up by switch_dev so it's named pdev instead.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-24 01:44:25 +01:00
Chuanhong Guo
2e6c96a649 generic: ar8216: drop duplicated include
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-24 01:44:25 +01:00
Chuanhong Guo
15323c4ef8 generic: ar8216: move chip id reading into a separate function
for mdio-device probing we still need to read chip id but ar8xxx_chip
can be determined using drvdata. We can't distinguish the buggy
standalone ar8216 and the builtin ar8216 in ar724x/ar933x using chip
id.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-24 01:44:25 +01:00
Chuanhong Guo
3771176c9e ath79: add support for linux 4.19
The following patches are dropped because they are merged upstream:
-0001-tty-serial-drop-QCA-pecific-SoC-symbols.patch
-0006-usb-drop-deprecated-symbols.patch
-0009-MIPS-ath79-add-lots-of-missing-registers.patch
-0010-MIPS-ath79-add-support-for-QCA953x-QCA956x-TP9343.patch
-0014-MIPS-ath79-finetune-cpu-overrides.patch
-0015-MIPS-ath79-enable-uart-during-early_prink.patch
-0016-MIPS-ath79-get-PCIe-controller-out-of-reset.patch

This patch is dropped due to the introduction of spi-mem framework:
-461-spi-ath79-add-fast-flash-read.patch

Thank to Michael Marley @mamarley for his work on this patch:
-910-unaligned_access_hacks.patch

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[synchronized kernel config with make kernel_oldconfig]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-24 01:44:25 +01:00
Chuanhong Guo
4eaa3626a8 ath79: ag71xx: pass correct device pointer to dma functions
linux 4.19 doesn't accept a NULL device for these functions.
It also complains that the device struct in net_device doesn't have
a dma_mask set.
Pass the device struct from platform_device for these functions.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-24 01:44:24 +01:00
Chuanhong Guo
8d3af284e0 ath79: ag71xx: add support for timer functions in linux 4.15+
Kernel newer than 4.15 dropped "data" field and used from_timer
to cast out the parent struct pointer for current timer.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-24 01:44:24 +01:00
Pawel Dembicki
67fced9ba3 ramips: add support for DLINK DIR-510L
The DIR-510L Wireless Router are based on the MT7620A SoC.

Specification:

-MediaTek MT7620A (580 Mhz)
-128 MB of RAM
-16 MB of FLASH
-802.11bgn radio
-1x 10/100 Mbps Ethernet
-2x internal, non-detachable antennas
-UART (J3) header on PCB (57600 8n1)
-1x bi-color LED (GPIO-controlled), 2x button
-JBOOT bootloader

Known issues:
-Ethernet port is used as LAN
-No communication with charger IC. (uart bitbang needed)

Installation:
Apply factory image via d-link http web-gui.

How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
    curl -F FN=@XXXXX.bin http://192.168.123.254/upg
    where XXXXX.bin is name of firmware file.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[fixed whitespace issue in 10-rt2x00-eeprom]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-24 01:44:24 +01:00
Pawel Dembicki
1f149fcad3 firmware-utils: mkdlinkfw: add kernel image offset
Some boards with JBOOT have partiton between bootloader
and kernel image. This patch add possibility to change kernel
partition start address.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-03-24 01:44:24 +01:00
Qin Wei
5f40b519f3 ramips: fix wrong i2s clock unit from kHz to MHz
clk_get_rate returns the current clock rate in Hz for a clock source so
if we divide it by 1M, then we get frequency in MHz and not kHz.

Signed-off-by: Qin Wei <support@vocore.io>
[added missing commit message, and fixed author with SoB from PR message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-24 01:44:24 +01:00
Felix Fietkau
503edc913b mt76: update to the latest version
4d8c7e8 mt76: mt76x02: send no-skb tx status without holding the status lock
7e9e9ad mt76: mt7603: add missing initialization for dev->ps_lock
3a7e6bb mt76: fix potential deadlock on cancelling workqueues
deacb8f mt76: fix using mac80211 tx skb header padding
c9402eb mt76: use napi polling for tx cleanup
60e508e mt76: use readl/writel instead of ioread32/iowrite32
5912e8a mt7603: fix sequence number assignment
95a83cc mt7603: send BAR after powersave wakeup

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-03-23 18:03:38 +01:00
Koen Vandeputte
0304e76cd1 kernel: bump 4.14 to 4.14.107
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-22 18:14:28 +01:00
Koen Vandeputte
fa91a147bb kernel: bump 4.9 to 4.9.164
Refreshed all patches.

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-22 18:14:28 +01:00
Koen Vandeputte
9c63141025 imx6: fix legacy IRQ support (4.19)
The PCIe DWC host controller is now using MSI
(Message-signaled-interrupts) by default.

While ath9k itself does support MSI here, a lot of wlan adapters do not.
Avoid non-functioning cards by simply continue to disable MSI for now.

This can be done by appending "pci=nomsi" to the boot cmdline.

Also an extra fix needs to be backported which avoids MSI initialization
which prevented legacy IRQ's init from taking over.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-22 18:14:28 +01:00
Koen Vandeputte
f7a057871b imx6: enable PCIe (4.19)
The DWC host controller symbols are now depending on a few others

Fixes: ca1b93f038 ("imx6: add support for kernel 4.19")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-22 18:14:28 +01:00
Koen Vandeputte
8877fdbf02 imx6: enable crypto acceleration (4.19)
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-22 18:14:28 +01:00
Koen Vandeputte
74f3cc04cd imx6: enable crypto acceleration
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-22 18:14:28 +01:00
Koen Vandeputte
d24bac0a95 imx6: refresh kernel configs
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-22 18:14:28 +01:00
Hans Dedecker
076c11a3aa glibc: update to latest 2.27 commit
1ab314d8d3 S390: Mark vx and vxe as important hwcap.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2019-03-22 10:57:05 +01:00
Tobias Schramm
d78e229903 ath79: Add support for Ubiquiti NanoBeam AC
The NanoBeam is a small AR9342 based directional 5 GHz AC CPE with hardware
almost identical to the Ubiquiti NanoStation AC loco. Over the NanoStation
AC loco it has 5 additional LEDs. Four of those LEDs are used as rssi
indicators, the fifth LED is used as an ethernet link/activity indicator.

CPU:   Atheros AR9342 SoC
RAM:   64 MB DDR2
Flash: 16 MB NOR SPI
WLAN:  QCA988X
Ports: 1x GbE

Flashing procedure is identical to the NanoStation AC loco and can be performed
either via serial or the factory firmware upgrade.

Serial flashing:

1. Connect to serial header on device (8N1 115200)
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy

Flashing through factory firmware:

1. Ensure firmware version v8.5.0.36727 is installed. Up/downgrade to this exact version.
2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real`
3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real`
4. Copy the squashfs factory image to /tmp on the device
5. Flash OpenWRT using `/tmp/fwupdate.real -m <squashfs-factory image>`
6. Wait for the device to reboot

Thanks to @cybermaus for testing!

Tested-by: Maurits van Dueren den Hollander <cybermaus@gmail.com>
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2019-03-22 00:40:29 +01:00
Xavier Douville
5ac974f214 ar71xx: Add support for Mikrotik RB SXT 2nD r3
The Mikrotik RouterBOARD SXT 2nD r3 is an outdoor WiFi AP / CPE
with a single 2.4 GHz radio and a 100 Mbps Ethernet port.
The device similar to the SXT 2nD r2, but it has SPI NOR flash instead
of NAND flash.

Hardware
--------
CPU:   Atheros AR9344 (600 MHz)
RAM:   64 MiB
FLASH: 16 MiB SPI NOR W25Q128
ETH:   1x 100 Mbps Atheros AG71xx
WiFi: 2T2R 802.11b/g/n (ath9k)
Power: Passive PoE 8-30 V

Installation instructions:

1. Boot openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf using a
   DHCP+TFTP server.
2. Erase the "firmware" partition using the mtd command. This should
   no longer be required once this patch is merged.
3. Use sysupgrade to install to flash. The file
   openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin
   should be used.

Signed-off-by: Xavier Douville <github@douville.org>
2019-03-22 00:40:29 +01:00
Florian Eckert
9be901061e build: suppress error output in feeds.mk
If no feed.conf or feeds.conf.default is found on image generation with
the imagebuilder we always get the following message "Unable to open
feeds configuration at <dir>/scripts/feeds line 48." on std error.

To get rid off this needless warning on image generation with the
imagebuilder supress the output in feeds.mk.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2019-03-22 00:40:29 +01:00
Hauke Mehrtens
94ffb7be4d netifd: update to latest git HEAD
a8cf037 netifd: wireless: Add support for GCMP cipher
34a70b6 netifd: wireless: Add support for 802.11ad

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-03-21 17:07:52 +01:00
Hauke Mehrtens
0168af502b ubox: update to latest git HEAD
a782779 kmodloader: increase module name length

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-03-21 17:07:47 +01:00
Hauke Mehrtens
9725aa271a iwinfo: update to latest git HEAD
ce1814b iwinfo: Add device ID for Wilocity Wil6210
a8e8275 iwinfo: Add support for 802.11ad

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-03-21 17:07:43 +01:00
Hauke Mehrtens
b36d250b55 Revert "valgrind: enable LTO and refresh patches"
This reverts commit 0331770299.

With LTO enabled valgridn does not build on MIPS32 any more, deactivate
it for now. The patch refresh was not reverted.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-03-21 17:07:00 +01:00
Rosy Song
488e7ccfbc libnftnl: bump to latest version
Signed-off-by: Rosy Song <rosysong@rosinson.com>
2019-03-21 17:05:44 +01:00
Eneas U de Queiroz
fc1386ccf8 openssl: revert disallowing parallel build
Openssl 1.1.0 made wholesale changes to its building system.
Apparently, parallel builds are working now.

Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
2019-03-21 17:05:34 +01:00
Hans Dedecker
1ca69003fd odhcpd: update to latest git HEAD (FS#2160)
6d23385 dhcpv6: extra syslog tracing
b076916 dhcpv6/router: add support for mutiple master interfaces
e4a24dc ndp: fix adding proxy neighbor entries
4ca7f7e router: add extra syslog tracing
8318e93 netlink: fix neighbor event handling (FS#2160)

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2019-03-21 16:06:10 +01:00
Aubrey McIntosh, PhD
34113999ef ar71xx: Remove ath10k packages from archer-c7-v1 (fixes FS#1743)
ath10k_pci driver crashes once loaded and causes boot loops on this
device as 5GHz radio QCA9880-AR1A shipped with this router is broken.
It's not possible to fix this problem in software, miniPCIe radio has to
be replaced.

We could've probably fixed crashing of the ath10k driver by reverting
following upstream commit:

 commit 1a7fecb766c83dace747f42b25bbb544b00a0163
 Author: Michal Kazior <michal.kazior@tieto.com>
 Date:   Sat Jan 24 12:14:48 2015 +0200

    ath10k: reset chip before reading chip_id in probe

but it's not worth the effort as it wouldn't make that 5GHz radio usable
anyway. So it seems more convenient to just remove the crashing driver
and provide bootable images, as I believe, that a router that is working
but degraded is better than a router that will not work.

For details please see discussions in PR[1] and in FS#1743[2].

1. https://github.com/openwrt/openwrt/pull/1349
2. https://bugs.openwrt.org/index.php?do=details&task_id=1743

Signed-off-by: Aubrey McIntosh, PhD <aubrey.mcintosh@utexas.edu>
[subject and commit message tweaks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-21 02:04:57 +01:00
Andreas Ziegler
78b9d57882 ath79: GL.iNet AR300M-nand/nor: correct LAN LED
The port labled as "LAN" is eth1.
That's different from the -lite variant,
where the only existing port eth0 is used as LAN

Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
2019-03-21 00:57:54 +01:00
Christian Lamparter
41bceb0d4e uboot-fritz4040: fix PKG_MIRROR_HASH
The PKG_MIRROR_HASH was for some reason wrong.

Fixes: d75db67870 ("uboot-fritz4040: bump version to 2019-03-03")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-21 00:57:54 +01:00
Christian Lamparter
133bad46a6 adb: fix missing PKG_MIRROR_HASH
This package was missing a PKG_MIRROR_HASH value.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-21 00:57:54 +01:00
Adrian Schmutzler
4269914187 ramips: Speed up eeprom read/write
Reading and writing to and from flash storage is slowed down
enormously by some functions which use a block size of 1.

This patch reworks the extraction scripts to be much faster and
efficient by reading and writing in possibly one big block.

This is based on the initial commit a69e101 for ipq40xx by
Christian Lamparter <chunkeey@gmail.com>.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Rosen Penev <rosenp@gmail.com>
2019-03-21 00:57:54 +01:00
Ozgur Can Leonard
201d3d1a82 ramips: Xiaomi MIR3G: detect board name from DTS
- Former "mir3g" board name becomes "xiaomi,mir3g".
- Reorder some entries to maintain alphabetical order.
- Change DTS so status LEDs (yellow/red/blue) mimic
  Xiaomi stock firmware: (Section Indicator)
<http://files.xiaomi-mi.co.uk/files/router_pro/router%20PRO%20EN.pdf>
<http://files.xiaomi-mi.co.uk/files/Mi_WiFi_router_3/MiWiFi_router3_EN.pdf>
|Yellow: Update (LED flickering), the launch of the system (steady light);
|Blue: during normal operation (steady light);
|Red: Safe mode (display flicker), system failure (steady light);

Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
[Added link to similar Router 3 model]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-21 00:57:54 +01:00
Josef Schlehofer
f22c33b40c ca-certificates: update to version 20190110
- Tested on Turris MOX, OpenWrt master
- Removed PKG_BUILD_DIR
In build_dir there were two folders
ca-certificates and ca-certificates-20190110 and it failed as files
were in ca-certificates-20190110

Signed-off-by: Josef Schlehofer <josef.schlehofer@nic.cz>
2019-03-21 00:57:54 +01:00
Steve Glennon
dc4f6b896f ipq40xx: add support for EnGenius ENS620EXT
Hardware
--------
CPU:   Qualcomm IPQ4018
RAM:   256M
FLASH: 32M SPI NOR W25Q256
ETH:   QCA8075
WiFi2: IPQ4018 2T2R 2SS b/g/n
WiFi5: IPQ4018 2T2R 2SS n/ac
LED:    - Power amber
        - LAN1(PoE) green
        - LAN2 green
        - Wi-Fi 2.4GHz green
        - Wi-Fi 5GHz green
BTN:    - WPS
UART:  115200n8 3.3V J1
       VCC(1) - GND(2) - TX(3) - RX(4)

Added basic support to get the device up and running for a sysupgrade
image only.
There is currently no way back to factory firmware, so this is a one-way
street to OpenWRT.
Install from factory condition is convoluted, and may brick your device:
1) Enable SSH and disable the CLI on the factory device from the web user
   interface (Management->Advanced)
2) Reboot the device
3) Override the default, limited SSH shell:
   a) Get into the ssh shell:
      ssh admin@192.168.1.1 /bin/sh --login
   b) Change the dropbear script to disable the limited shell. At the
      empty command prompt type:
        sed -i '/login_ssh/s/^/#/g’ dropbear
        /etc/init.d/dropbear restart
        exit
4) ssh in to a (now-) normal OpenWRT SSH session
5) Flash your built image
   a) scp openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin
      admin@192.168.1.1:/tmp/
   b) ssh admin@192.168.1.1
   c) sysupgrade -n
      /tmp/openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin
6) After flash completes (it may say "Upgrade failed" followed by
   "Upgrade completed") and device reboots, log in to newly flashed
   system. Note you will now need to ssh as root rather than admin.

Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
[whitespace fixes, reordered partitions, removed rng node from 4.14,
fixed 901-arm-boot-add-dts-files.patch]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-21 00:57:54 +01:00
INAGAKI Hiroshi
5c11258297 ramips: add support for I-O DATA WN-AC733GR3
I-O DATA WN-AC733GR3 is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7620A.

Specification

- SoC		: MediaTek MT7620A
- RAM		: DDR2 64 MiB
- Flash		: SPI-NOR 8 MiB
- WLAN		: 2.4/5 GHz
  - 2.4 GHz : MT7620A (SoC), 2T2R
  - 5 GHz   : MT7610E, 1T1R
- Ethernet	: 10/100/1000 Mbps (RTL8367RB)
- LED/key	: 4x/4x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J1: Vcc, RX, GND, TX from LED side
  - 57600n8

Flash instruction using factory image:

1. Boot WN-AC733GR3 normaly
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-03-21 00:57:20 +01:00
Petr Štetiar
d2c3eb1e43 kernel: brcm47xx: Backport fixes for USB on WNDR3400v2 (fixes FS#2170)
Eric has reported on OpenWrt's bug tracking system[1], that he's not
able to use USB devices on his WNDR3400v2 device after the boot, until
he turns on GPIO #21 manually through sysfs.

1. https://bugs.openwrt.org/index.php?do=details&task_id=2170

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-20 23:18:46 +01:00
Petr Štetiar
846f98056a kernel: Backport ar933x_uart build fix (fixes FS#2152)
Andrey has reported on OpenWrt's bug tracking system[1], that he
currently can't use ar93xx_uart as pure serial UART without console
(CONFIG_SERIAL_8250_CONSOLE and CONFIG_SERIAL_AR933X_CONSOLE undefined),
because compilation ends with following error:

 ar933x_uart.c: In function 'ar933x_uart_console_write':
 ar933x_uart.c:550:14: error: 'struct uart_port' has no
                               member named 'sysrq'

1. https://bugs.openwrt.org/index.php?do=details&task_id=2152

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-20 23:07:03 +01:00
Deng Qingfang
31078dbc76 iproute2: update to 5.0.0
Update iproute2 to 5.0.0
Remove upstream patch 001-tc-fix-undefined-XATTR_SIZE_MAX
Alter patch 170-ip_tiny as support for IPX and DECnet is dropped
Update patch 010-cake-fwmark to match upstream commit

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-03-20 21:48:04 +01:00
Daniel Engberg
8568dcd931 toolchain: Remove binutils 2.29 for ARC targets
Remove binutils 2.29 for ARC targets

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2019-03-20 18:23:39 +01:00