According to a user in OpenWrt forum, on RouterOS the MAC addresses are
ether1(WAN) = MAC
ether2(LAN2) = MAC+1
ether3(LAN3) = MAC+2
etc.
Fix the MAC addresses in OpenWrt.
Ref: https://forum.openwrt.org/t/few-dumb-question-about-mt7530-rb750gr3-dsa/61608
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[remove label_mac in 02_network]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
SFP cage of this device is connected via a AT8031 phy to port 5 of the switch.
This phy act as a RGMII-to-SerDes converter.
Also a I2C clock gate needs to be enabled in order to access the SFP module via I2C bus.
SFP cage also has module detect pin which is connected to I2C gpio expander.
With this patch the kernel/PHYLINK now can detect, readout and use the SFP module/port.
NOTE: SFP cage / AT8033 PHY only support 1000base-X encoding!
This means that some SGMII modules can work and only at forced 1GBit/full-duplex!
Signed-off-by: René van Dorst <opensource@vdorst.com>
The pinctrl driver had been replaced with the upstream one in b756ea2a90
("ramips: replace pinctrl property names"), but the initial A1004ns support
patch did not reflect the changes. This commit updates its pinctrl property
names.
Fixes: 9169482f64 ("ramips: add support for ipTIME A1004ns")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This commit increases the hardware SPI frequency from 24.2MHz to 48.3MHz.
[ 5.314163] m25p80 spi0.0: speed: 24166666/40000000, rate: 8, prescal: 2, loops: 226
[ 5.076323] m25p80 spi0.0: speed: 48333333/50000000, rate: 4, prescal: 1, loops: 162
`time cat /dev/mtd2 >/dev/null` is reduced from 5.64s to 4.36s on A104ns,
and from 11.39s to 8.81s on A1004ns.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
These stock partitons: "backup", "hw_panic", "overly", firmware_backup", "opt"
do not contain any device-specific data and can be used for /overlay, resulting in
121M space
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Increase kernel partition because 2M is insufficient for 5.4
Because the partition changes, previous version of OpenWrt cannot upgrade
to this version, and requires a new installation
Recovery to stock instruction:
1. Download stock firmware at
http://ur.ikcd.net/HC5962-sysupgrade-20171221-b00a04d1.bin
2. Power off the router
3. Press and hold the reset button for 4~6 sec while power it back on
4. Connect a PC to router's LAN
5. Visit http://192.168.2.1 and upload the firmware
Then repeat the instruction in edae3479e6 to install OpenWrt
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Upstream pinctrl driver in drivers/staging uses
groups/function/ralink,num-gpios instead of
ralink,group/ralink,function/ralink,nr-gpio
Replace these properties in dts as well as the pinctrl driver in
patches-4.14.
This commit is created using:
sed -i 's/ralink,group/groups/g'
sed -i 's/ralink,function/function/g'
sed -i 's/ralink,nr-gpio/ralink,num-gpios/g'
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
upstream driver merged 3 separated gpio banks into one gpio node.
and gpioX Y in our local driver should be replaced with gpio X*32+Y.
This patch is created using the following sed command:
sed -i -r 's/(.*)gpio([0-9]) ([0-9]+)(.*)/echo "\1gpio $((\2*32+\3))\4"/ge'
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
increase spi frequency for both devices to 45MHz.
while at it, also remove m25p,fast-read for newifi d1 as it's only
needed when spi clock is higher than 50MHz.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
These are boards known to start on 3-byte address mode, which requires
broken-flash-reset if 4B_OPCODES isn't supported by the flash.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The "proper" vendor prefix for Ubiquiti is "ubnt", this is used in
all targets except ramips and also recommended by the kernel.
This patch adjusts the various board/image/device name variables
accordingly. Since we touch it anyway, this also adds the space
in "EdgeRouter X" as a hyphen to those variables to really make
them consistent with the model name.
While at it, create a real shared definition for the devices in
image/mt7621.mk instead of deriving one device from another.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
I-O DATA WN-AX2033GR is roughly the same as I-O DATA
WN-AX1167GR2. The difference is Wi-Fi feature.
Specification
=============
- SoC: MediaTek MT7621A
- RAM: DDR3 128 MiB
- Flash Memory: NAND 128 MiB (Spansion S34ML01G200TF100)
- Wi-Fi: MediaTek MT7603E
- Wi-Fi: MediaTek MT7615
- Ethernet: 5x 10 Mbps / 100 Mbps / 1000 Mbps (1x WAN, 4x LAN)
- LED: 2x green LED
- Input: 2x tactile switch, 1x slide switch
- Serial console: 57600bps, PCB through hole J5 (Vcc, TX, RX, NC, GND)
- Power: DC 12V
This device only supports channel 1-13 and 36-140.
Thus, narrower frequency limits compared to other devices are required
for limiting wi-fi frequency correctly.
Without this, non-supported frequencies are activated.
Flash instructions
==================
1. Open the router management page (192.168.0.1).
2. Update router firmware using "initramfs-kernel.bin".
3. After updating, run sysupgrade with "sysupgrade.bin".
Recovery instructions
=====================
WN-AX2033GR contains Zyxel Z-LOADER
1. Setup TFTP server (IP address: 10.10.10.3).
2. Put official firmware into TFTP server directory (distribution site:
https://www.iodata.jp/lib/software/w/2068.htm)
3. Connect WX-AX2033GR Ethernet port and computer that runs TFTP server.
4. Connect to serial console.
5. Interrupt booting by Esc key.
6. Flash firmware using "ATNR 1,[firmware filename]" command.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[adjust for kernel 5.4, add recovery instructions/frequency comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ZyXEL Keenetic has 8MB flash, but OpenWrt uses only 4MB.
This commit fixes the problem.
WikiDevi page [1] says that ZyXEL Keenetic has FLA1: 8 MiB, there is
an article with specs [2] (in Russian).
[1] https://wikidevi.wi-cat.ru/ZyXEL_Keenetic
[2] https://3dnews.ru/608774/page-2.html
Fixes: FS#2487
Fixes: a7cbf59e0e ("ramips: add new device ZyXEL Keenetic as kn")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
So far, image/device/board names for Mikrotik devices in mt7621 have
been used quite inconsistently.
This patch harmonizes the naming scheme by applying the same style
as used lately in ath79, i.e. using "RouterBOARD" as separate word
in the model name (instead of RB prefix for the number) and deriving
the board/device name from that (= make lower case and replace spaces
by hyphens).
This style has already been used for most the model/DEVICE_MODEL
variables in mt7621, so this is essentially just adjusting the remaining
variables to that.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Buffalo WSR-2533DHPL is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : SPI-NOR 16 MiB
- WLAN : 2.4/5 GHz 4T4R (2x MediaTek MT7615N)
- Ethernet : 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 8x/6x (3x buttons, 2x slide-switches)
- UART : through-hole on PCB
- J4: 3.3V, GND, TX, RX from triangle-mark
- 57600n8
- Power : 12VDC 1.5A
Flash instruction using initramfs image:
1. prepare the TFTP server with the initramfs image renamed to
"linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPL
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL downloads
the initramfs image and boot with it automatically
4. on the initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
5. wait ~120 seconds to complete flashing
Switch position overview:
- slide-switch1 (2x positions)
- "AUTO"
- "MANUAL" (not connected to gpio)
- slide-switch2 (3x positions)
- "ROUTER"
- "AP" (not connected to gpio)
- "WB"
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add note on switches, fix group->groups for state_default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This changes the node names for the LEDs in the Netgear R6120
device-tree file to provide consistency with other devices.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
LAN ports of MTC WR1201 are reversed, so correct their names
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
The original idea of bitbanged I2C is to use i2c-gpio-custom
Since i2c-gpio-custom is no longer available on 5.4, use SoC I2C instead
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
The name of each user port should be eth0..4, instead of lan1..4
and there is no WAN port. Rename them to match the official firmware.
To avoid conflict with the master port (gmac0), rename it to "dsa".
The official firmware assigns MAC address in this way:
eth0 = label mac
eth1 = label mac + 1
...
eth4 = label mac + 4
Since we have switched to DSA, it's possible to use different MAC for each port.
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
update dts and network/LED configuration for DSA driver.
sysupgrade from images prior to this commit with config preserved
will cause broken ethernet setup.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Acked-by: Jo-Philipp Wich <jo@mein.io>
[split commit]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
There's different gpio and ethernet drivers upstream for mt7621.
Update these two nodes to match upstream dt bindings.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
TOTOLINK A3 is a clone of ipTIME A3. The only difference is the model name.
Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7612EN
- Ethernet: 3x 10/100Mbps
- Switch: SoC internal
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Tested on device by JasonHCH <hsuan670629@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Hardware
--------
SoC: MediaTek MT7621AT
WiFi: MediaTek MT7603 bgn 2T2R
MediaTek MT7615 ac 4T4R
Flash: 32M SPI (Macronix MX25L25635F)
RAM: 128M DDR3 (Winbond W631GG6KB)
LED: Dome (Blue / White)
BTN: Reset
Installation
------------
These instructions were written for firmware version v3.9.27.
Downgrade if necessary.
1. Copy the OpenWrt sysupgrade image to the devices /tmp folder
via scp. On factory defaults, user and password is "ubnt" at
192.168.1.20/24.
2. Write the bootselect flag. Otherwise, the device might boot from the
wrong partition. Verify the mtd partition used in the command below
is the one labled "bs" in /proc/mtd (as this might change in the
future).
> dd if=/dev/zero bs=1 count=1 of=/dev/mtd4
3. Write the OpenWrt sysupgrade to the mtd partitions labled
"kernel0" and "kernel1".
> dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock6
> dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock7
4. Reboot or powercycle the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
SoC: MediaTek MT7620A
RAM: 64MB
FLASH: 8MB SPI
WLAN: 2G: MediaTek MT7620A
5G: MediaTek MT7610EN
ETH: 1x 10/100/1000M (Atheros AR8035)
LED: RSSI (orange/green)
WiFi 2G (green)
WiFi 5G (green)
Power (green)
System (red / green)
BTN: Power
Reset
LED
WPS
Serial
------
P1 - Tx
P2 - Rx
P3 - GND
P4 - VCC
Pin 4 is the one closest to the LAN port.
MAC overview
------------
WAN *:4c uboot 0x1fc00
2.4 *:4c uboot 0x1fc00
5 *:4e uboot 0x1fc00 +2
Installation
------------
Web interface:
It is possible to upgrade to OpenWrt via the web interface. However, the
OEM firmware upgrade file is required and a tool to fix the MD5 sum of
the header. This procedure overwrites U-Boot and there is not failsafe /
recovery mode present! To prepare an image, you need to take the header
and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and
attach the factory image to it. Then fix the header MD5Sum1.
Serial/TFTP:
You can use initramfs for booting via RAM or flash the image directly.
Additional Notes:
If the web interface upgrade fails, you have to open your device and
attach serial console. Since the web upgrade overwrites the boot loader,
you might also brick your device.
In order to flash back to stock, the first header and U-Boot needs to be
stripped from the original firmware.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[change rssi LED labels]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Read times drop when increasing frequency to 25 MHz and 50 MHz,
but not in between or for further increase. So, use 50 MHz as the
lowest frequency with the fastest speed.
Test results (thanks to Roger):
The device reports a mx25l6405d flash chip. I tried all the maximum
values in the devices' datasheet (Table 10. AC CHARACTERISTICS). All of
them worked with and without "m25p,fast-read":
> 10 MHz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 1m 33.00s
user 0m 0.01s
sys 1m 7.56s
> 25 MHz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 34.42s
user 0m 0.02s
sys 0m 23.58s
> 25 MHz, fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 34.45s
user 0m 0.02s
sys 0m 23.59s
> 33 MHz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 34.39s
user 0m 0.00s
sys 0m 23.60s
> 33 MHz, fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 34.46s
user 0m 0.01s
sys 0m 23.62s
> 50 MHz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 26.81s
user 0m 0.01s
sys 0m 18.25s
> 50 MHz, fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 26.84s
user 0m 0.00s
sys 0m 18.25s
> 66 MHz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 26.80s
user 0m 0.01s
sys 0m 18.23s
> 66 MHz, fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 26.80s
user 0m 0.02s
sys 0m 18.23s
> 86 MHz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 26.84s
user 0m 0.01s
sys 0m 18.24s
> 86 MHz, fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 26.80s
user 0m 0.02s
sys 0m 18.23s
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This patch addresses several issues for D-Link DIR-810L:
- add correct button codes
- harmonize button node names
- use generic flash@0
- remove unused pin groups from state_default
- improve sorting of properties
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
The Jffs2 partition for the D-Link DIR-810L is currently off by
0x10000. Apply the correct offset based on the other partitions'
size/offset and the information about stock OS from the Wiki.
This is just based on the named information and _not_ verified
on device.
Fixes: 36e3424fa5 ("ramips: add support for dir810l and asus rp-n53")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This patch adds support for the Netgear R6800, aka Netgear AC1900 and
R6800-100PES.
Specification:
- SoC: MediaTek MT7621AT (880 MHz)
- Flash: 128 MiB NAND
- RAM: 256 MiB
- Wireless: MediaTek MT7615EN b/g/n , MediaTek MT7615EN an+ac
- LAN speed: 10/100/1000
- LAN ports: 4
- WAN speed: 10/100/1000
- WAN ports: 1
- USB 2.0
- USB 3.0
- Serial baud rate of Bootloader and factory firmware: 57600
Known issues:
- Device has 3 wifi LEDs: Wifi 5Ghz, Wifi 2.4Ghz and Wifi on/off.
Wifi on/off is not used.
Installation:
- apply factory image via stock web-gui.
Back to stock:
- nmrpflash can be used to recover to the stock Netgear firmware.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
All devices inherited from mt7628an_tplink_8m.dtsi and
mt7628an_tplink_8m-split-uboot.dtsi contain the same additional
includes in the DTS files.
Move them to the DTSI files instead.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, the compatible for the Ubiquiti Edgerouter X has been
defined in the DTSI file and inherited for the edgerouterx.dts,
but overwritten for the edgerouterx-sfp.dts. In contrast, the
model was stored in the DTS file in both cases.
To resolve this somewhat confusing situation, move the compatible
with the device name for edgerouterx to the DTS file as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Many DTS files contain the same includes again that are already
present in the DTSI files they are derived from.
Remove those redundant includes in the DTS files. For vocore, the
include is moved to the parent DTSI file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The correct model name of WF-2881 is WF2881 without hyphen. The former used
boardnames are not added to SUPPORTED_DEVICES, to make it explicit that the
sysupgrade-tar image, which is newly added in the previous commit, should
not be used to upgrade from older version.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
WF-2881 sysupgrade image uses UBI rootfs, but still relies on
default_do_upgrade. Because of this, config backup is not restored after
sysupgrade. It can be fixed by switching to nand_do_upgrade and
sysupgrade-tar image. default_do_upgrade does not handle sysupgrade-tar
properly, so one should use factory image to upgrade from older version.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
dts file does not need to be executable. 644 is enough.
Fixes: f098c612b6 ("ramips: create shared DTSI for Netgear EX2700 and WN3000RP v3")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
