Both the GPL driver from ZyXEL and the xrx200 driver have this error. The flags
are reversed. Full duplex is marked as half and the other way around. With this
fix the switch will push full GBit speeds.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40312
Export the ubi_num and vol_id into the sysfs record of the gluebi-
emulated mtd device. Previously userspace didn't have a way to
map gluebi-emulated devices back to their corresponding ubi volumes.
SVN-Revision: 40306
If the CPU port is not forced up, the link, at least on this board, is lost after
changes are applied. This makes sure that the link is restored. Regression tests
should confirm it doesn't break other boards.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40305
- hide port pvid - vlan index relation
- switch initialises with vlans disabled so port isolation is not used
- remove special treatment of cpu port
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40304
Changes to:
- show the correct "enable_vlan" value under "Global attributes"
- show tagged ports under "Vlan: ports"
- use get_port_link method to report link status
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40303
fixes incremental build with change to CONFIG_DROPBEAR_ECC
drop --with-shared which is unknown to configure
Patch by Catalin Patulea <cat@vv.carleton.ca>
SVN-Revision: 40300
Without timeout mechanism, if ssh client disconnected without sending
FIN or RST, forked dropbear servers would hang there for
KEX_RETRY_TIMEOUT seconds (8 hours).
TCP keepalive is not implemented in dropbear yet, thus the name
SSHKeepAlive.
300 seconds in this patch is selected from the default value of
ServerAliveInterval for Debian ssh client (See man ssh_config).
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 40299
The antenna gain attribute has been removed from the upstream regulatory database.
Incorperate patch from Luis R. Rodriguez to skip the parsing of the gain attribute
in genregdb.awk in order to emit proper rules again.
Also refresh fuzzy patches while we're at it.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 40296
The version of TL-WDR4300 sold in Israel comes with a different
hardware id.
Patch-by: Daniel <daniel@makrotopia.org>
Patchwork: http://patchwork.openwrt.org/patch/5001/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40038
The version of TL-WDR4300 sold in Israel comes with a different
hardware id.
Patch-by: Daniel <daniel@makrotopia.org>
Patchwork: http://patchwork.openwrt.org/patch/5001/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40037
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg: use correct board name in uci-defaults/02_network]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40033
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg:
- use a separate patch for kernel changes,
- reorder Kconfig and Makefile entries,
- change function and variable names to be lowercase only
and fix misaligned tabs in mach-gs-oolite.c,
... ]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40032
NAND flash is very likely to contain bad blocks.
Currently, mtd and therefore sysupgrade fails when it encounters a single bad block, potentially leaving an unbootable system.
This patch allows the mtd utility to skip bad blocks in NAND flash and complete sysupgrade successfully.
Patch by: Matthew Redfearn <matt.redfearn@nxp.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40021
