Commit Graph

3735 Commits

Author SHA1 Message Date
Shiji Yang
fb4cea45ec
ramips: convert MT7603 EEPROM to NVMEM format
This patch converts MT7603 WiFi calibration data to NVMEM format. The
EEPROM size is 0x400.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-09 11:15:52 +02:00
Shiji Yang
230d5de707
ramips: correct NVMEM MAC address node name and label for Bolt Arion
The node name&label should match the address in the 'reg' property,
so it's better to change the incorrect offset to the 0x28.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-09 11:15:51 +02:00
Shiji Yang
22b0c36ae7
ramips: fix EEPROM size for I-O DATA WN-DEAX1800GR
I-O DATA WN-DEAX1800GR uses MT7915 PCIe NIC. The correct EEPROM
size is 0xe00.

Fixes: ac68fbf526 ("ramips: add support for I-O DATA WN-DEAX1800GR")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-09 11:15:51 +02:00
Alexey D. Filimonov
ff95f859eb ramips: cf-ew72-v2: Add support for COMFAST CF-EW72 V2
Add support for COMFAST CF-EW72 V2

Hardware:
-   SoC: Mediatek MT7621 (MT7621DAT or MT7621AT)
-   Flash: 16 MiB NOR
-   RAM: 128 MiB
-   Ethernet: Built-in, 2 x 1GbE
-   Power: only 802.3af PD on any port, injector supplied in the box
-   PoE passthrough: No
-   Wifi 2.4GHz: Mediatek MT7603BE 802.11b/g/b
-   Wifi 5GHz: Mediatek MT7613BEN 802.11ac/n/a
-   LEDs: 8x (only 1 is both visible and controllable, see below)
-   Buttons: 1x (RESET)

Installing OpenWrt:
Flashing is done using Mediatek U-Boot System Recovery Mode
-   make wired connection with 2 cables like this:
-     -   PC (LAN) <-> PoE Injector (LAN)
-     -   PoE Injector (POE) <-> CF-EW72 V2 (LAN). Leave unconnected to CF-EW72 V2 yet.
-   configure 192.168.1.(2-254)/24 static ip address on your PC LAN
-   press and keep pressed RESET button on device
-   power the device by plugging PoE Injector (POE) <-> CF-EW72 V2 (LAN) cable
-   wait for about 10 seconds until wifi led stops blinking and release RESET button
-   navigate from your PC to http://192.168.1.1 and upload OpenWrt *-factory.bin firmware file
-   proceed until router starts blinking with wifi led again (flashing) and stops (rebooting to OpenWrt)

MAC addresses as verified by OEM firmware:
  vendor OpenWrt  address
  LAN    lan\eth0 label
  WAN    wan     label + 1
  2g     phy0    label + 2
  5g     phy1    label + 3

  The label MAC address was found in 0xe000.

LEDs detailed:
  The only both visible and controllable indicator is blue:wlan LED.
  It is not bound by default to indicate activity of any wireless interfaces.

  Place (WAN->ANT) | Num | GPIO | LED name (LuCI)   | Note
  -----------------|-----|-----------------------------------------------------------------------------------------
             power | 1   |      |                   | POWER LED. Not controlled with GPIO.
      hidden_led_2 | 2   | 13   | blue:hidden_led_2 | This LED does not have proper hole in shell.
               wan | 3   |      |                   | WAN LED. Not controlled with GPIO.
      hidden_led_4 | 4   | 16   | blue:hidden_led_4 | This LED does not have proper hole in shell.
               lan | 5   |      |                   | LAN LED. Not controlled with GPIO.
      noconn_led_6 | 6   |      |                   | Not controlled with GPIO, possibly not connected
              wlan | 7   | 15   | blue:wlan         | WLAN LED. Wireless indicator.
      noconn_led_8 | 8   |      |                   | Not controlled with GPIO, possibly not connected

  mt76-phy0 and mt76-phy1 leds also exist in OpenWrt, but do not exist on board.

Signed-off-by: Alexey D. Filimonov <alexey@filimonic.net>
2023-09-27 00:10:16 +02:00
Andreas Böhler
191da23551 ramips: fix Mercusys MR70X LAN port assignments
A bug report in the forum found that the MR70X lists four LAN ports in LuCI
while it has only three. This adds the device to the network setup file
to fix the issue.

Identified-by: Forum User "Lexeyko"
Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-09-24 17:09:26 +02:00
Sijia Huang
ab12a01cd7 ramips: add support for WAVLINK WL-WN573HX1
Hardware
--------

Specifications:
- Device: WAVLINK WL-WN573HX1 Outdoor AP
- SoC: MT7621AT
- Flash: 16MB
- RAM: 256MB
- Switch:1 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LEDs: 1x STATUS (blue, configurable)
		1x LAN (green)

Product link:
https://www.wavlink.com/en_us/product/WL-WN573HX1.html

Signed-off-by: Sijia Huang <engineer31@win-star.com>
2023-09-24 12:36:52 +02:00
John Audia
ac422c9788
kernel: bump 5.15 to 5.15.132
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.132

Removed upstreamed:
	bcm53xx/patches-5.15/037-v6.6-0006-ARM-dts-BCM53573-Add-cells-sizes-to-PCIe-node.patch[1]
	bcm53xx/patches-5.15/037-v6.6-0007-ARM-dts-BCM53573-Use-updated-spi-gpio-binding-proper.patch[2]
	bcm53xx/patches-5.15/037-v6.6-0008-ARM-dts-BCM5301X-Extend-RAM-to-full-256MB-for-Linksy.patch[3]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=b35f3ca1877e024887df205ede952863d65dad36
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=2840d9b9c8750be270fb1153ccd5b983cbb5d592
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=f086e859ddc252c32f0438edff241859c0f022ce

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-09-20 14:13:00 +02:00
Max Qian
794349a28a ramips: RT1800: fix invalid octal number error
This commit removes the padded zeros in the date formatting.
The padded zeros from the date command causes the numbers
to be interpreted as an octal number by printf. Months, days,
and years with the number 08 or 09 raise an error in printf as an
"invalid octal number" and get interpreted as a zero.

Signed-off-by: Max Qian <public@maxqia.com>
2023-09-17 13:52:55 -07:00
Aviana Cruz
46d673033b
ramips: add support for mtk eip93 crypto engine
Mediatek EIP93 Crypto engine is a crypto accelerator which
is available in the Mediatek MT7621 SoC.

Signed-off-by: Aviana Cruz <gwencroft@proton.me>
Co-authored-by: Richard van Schagen <vschagen@icloud.com>
Co-authored-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-09-12 14:57:54 +02:00
Daniel Golle
3b86c1f929 kernel: backport two fixes for MediaTek Ethernet driver
Fix PSE port assignment for 3rd GMAC on MT7988 and make sure dma_addr
is always initialized to prevent potentially accessing uninitialized
stack memory in the error path.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-09-11 14:09:48 +01:00
Piotr Dymacz
f1aaa267f0 ramips: add support for ALFA Network AX1800RM
ALFA Network AX1800RM (FCC ID: 2AB877621) is a dual-band Wi-Fi 6
(AX1800) router, based on MediaTek MT7621A + MT79x5D platform.

Specifications:

- SOC:      MT7621A (880 MHz)
- DRAM:     DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash:    16 MiB SPI NOR (EN25QH128A-104HIP)
- Ethernet: 4x 10/100/1000 Mbps (SOC's built-in switch)
- Wi-Fi:    2x2:2 2.4/5 GHz (MT7905DAN + MT7975DN)
            (MT7905DAN doesn't support background DFS scan/BT)
- LED:      6x green, 1x green/red
- Buttons:  2x (reset, WPS)
- Antenna:  4x external, non-detachable omnidirectional
- UART:     1x 4-pin (2.54 mm pitch, J4, not populated)
- Power:    12 V DC/1 A (DC jack)

MAC addresses:

LAN:     00:c0:ca:xx:xx:4e (factory 0x4, +2)
WAN:     00:c0:ca:xx:xx:4f (factory 0x4, +3)
2.4 GHz: 00:c0:ca:xx:xx:4c (factory 0x4, device's label)
5 GHz:   00:c0:ca:xx:xx:4c (factory 0xa)

Flash instructions for web-based U-Boot recovery:

1. Power the device with WPS button pressed and wait around 10 seconds.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'recovery' image.

The device runs LEDE 17.01 (kernel 4.4.x) based firmware with 'failsafe'
mode available which allows alternative upgrade method:

1. Run device in 'failsafe' mode and change password for default user.
2. SSH to the device, transfer 'sysupgrade' image and perform upgrade
   in forced mode, without preserving settings: 'sysupgrade -n -F ...'.

Other notes:

If you own early version of this device, the vendor firmware might
refuse OpenWrt image because of missing custom header. In that case,
ask vendor's customer support for stock firmware without custom header
support/requirement.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2023-09-11 11:41:57 +02:00
John Audia
58bb5e147a kernel: bump 5.15 to 5.15.131
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.131

All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-09-08 21:24:48 +02:00
Daniel Golle
f631c7bbb1 generic: sync MediaTek Ethernet driver with upstream
Import commits from upstream Linux replacing some downstream patches.
Move accepted patches from pending-{5.15,6.1} to backport-{5.15,6.1}.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 16:35:22 +01:00
Rani Hod
a4eb1ea331 ramips: add support for D-Link DRA-1360
The DRA-1360 rev A is a wall-plug AC1300 repeater.
Hardware is identical (same FCC ID, black case instead of white)
to D-Link DAP-1620 rev B, which is already supported, but a
different model name, revision, and hardware ID are needed.
Thus, the bulk of the DAP-1620 device tree is extracted to a
common dtsi included by the two models' device trees.

Repeating specs and installation instructions from e4c7703:
(note that the RAM size mentioned there was incorrect, oops)

Specs:
- SoC: MT7621AT (880MHz dual-core MIPS1004Kc)
- Memory: 128 MiB RAM, 16 MiB NOR SPI
- WiFi: MT7615DN 2x2 802.11n + 2x2 802.11ac (DBDC)
- Ethernet: 1 RJ45 port 10/100/1000
- Power/status LED: red+green
- LED RSSI bargraph: 2x green, 1x red+green

Installation:
- Keep reset button pressed during plug-in
- Web Recovery Updater is at 192.168.0.50
  (pings are ignored, it listens only for http)
- Upload factory.bin, confirm flashing
  (seems to work best with Chromium-based browsers)

Revert to OEM firmware:
- tail -c+117 DRA1360A1_FW112B03.bin | \
  openssl aes-256-cbc -d -md md5 -out decrypted.bin \
  -k c471706398cb147c6619f8a04a18d53e9c17ede8
- flash decrypted.bin via D-Link Web Recovery

Signed-off-by: Rani Hod <rani.hod@gmail.com>
2023-08-27 19:13:36 +02:00
INAGAKI Hiroshi
ac68fbf526 ramips: add support for I-O DATA WN-DEAX1800GR
I-O DATA WN-DEAX1800GR is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based
on MT7621A.

Specification:

- SoC         : MediaTek MT7621A
- RAM         : DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash       : RAW NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN        : 2.4/5 GHz (MediaTek MT7915)
- Ethernet    : 5x 10/100/1000 Mbps
  - Switch    : MT7530 (SoC)
- LEDs/Keys   : 6x/3x
- UART        : through-hole on PCB (J2)
  - assignment: 3.3V, GND, TX, RX from "1" marking
  - settings  : 115200n8
- Power       : 12 VDC, 1 A

Flash instruction using initramfs-factory image:

1. Boot WN-DEAX1800GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
   ("ファームウェア")
3. Select the OpenWrt initramfs-factory.bin image and click update
   ("更新") button to perform firmware update
4. On the initramfs image, perform sysupgrade with the
   squashfs-sysupgrade.bin image
5. Wait ~120 seconds to complete flashing

Note:

- This device has 2x OS images on the flash storage. In this support,
  the first one will be used.

Warning:

- Do not use "saveenv" command on U-Boot CLI.
  This device has wrong u-boot-env data. The actual length of individual
  env data installed to the device is 0x1000 (4 KiB), but installed
  U-Boot requires 0x20000 (128 KiB). So U-Boot determines the data is
  invalid. Then, if you perform saving environment data with saveenv on
  U-Boot CLI, installed env data will be overwritten with too few
  default values without individual values (SSID, password, MAC
  addresses, etc...).

MAC addresses:

LAN    : 50:41:B9:xx:xx:F4 (Config, ethaddr (text))
WAN    : 50:41:B9:xx:xx:F6 (Config, wanaddr (text))
2.4 GHz: 50:41:B9:xx:xx:F4 (Config, rmac (text) / Factory, 0x4 (hex))
5 GHz  : 50:41:B9:xx:xx:F5 (none)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-08-20 01:26:15 +02:00
INAGAKI Hiroshi
9088b5445f ramips: improve sysupgrade helpers for I-O DATA devices
I-O DATA devices manufactured by MSTC (MitraStar Technology Corp.)
have some important flags for booting, "bootnum" and "debugflag".
The almost devices have both flags but some devices have only
"bootnum" flag.
So optimize helper functions in iodata.sh to set each flags.

- both:
  - WN-AX1167GR2
  - WN-AX2033GR
  - WN-DX1167R
  - WN-DX1200GR
  - WN-DX2033GR

- "bootnum" only
  - WN-DEAX1800GR

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-08-20 01:26:15 +02:00
Ivan Pavlov
54e5e396c5 ramips: improve Xiaomi mi-mini indications
Sets status indications led color on Xiaomi mi-mini router as other Xiaomi routers

Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
2023-08-14 20:08:05 +02:00
John Audia
daed3322d3 kernel: bump 5.15 to 5.15.125
1. Add new symbols to generic config
2. Bump kernel
   Changelog: https://lore.kernel.org/stable/2023080818-groin-gradient-a031@gregkh/

   All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-09 22:06:24 +02:00
John Audia
81c1172c36 kernel: bump 5.15 to 5.15.124
Changelog: https://lore.kernel.org/stable/2023080341-curliness-salary-4158@gregkh/

1. Needed to make a change to to package/kernel/linux/modules/netsupport.mk
   due to upstream moving vxlan to its own directory[1].  @john-tho suggested
   using the the 6.1 xvlan FILES to circumvent.
2. All patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.124&id=77396fa9096abdbfbb87d63e73ad44d5621cf103

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-09 22:06:23 +02:00
John Audia
8590531048 kernel: bump 5.15 to 5.15.123
Manually rebased:
	bcm4908/patches-5.15/071-v6.1-0001-net-broadcom-bcm4908_enet-handle-EPROBE_DEFER-when-g.patch
	bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
	ipq40xx/patches-5.15/902-dts-ipq4019-ap-dk04.1.patch[*]

Removed upstreamed:
	backport-5.15/735-v6.5-net-bgmac-postpone-turning-IRQs-off-to-avoid-SoC-han.patch[1]
	backport-5.15/817-v6.5-01-leds-trigger-netdev-Recheck-NETDEV_LED_MODE_LINKUP-o.patch[2]
	pending-5.15/143-jffs2-reduce-stack-usage-in-jffs2_build_xattr_subsys.patch[3]
	pending-5.15/160-workqueue-fix-enum-type-for-gcc-13.patch[4]
	bcm53xx/patches-5.15/036-v6.5-0003-ARM-dts-BCM5301X-Drop-clock-names-from-the-SPI-node.patch[5]
	bcm53xx/patches-5.15/036-v6.5-0015-ARM-dts-BCM5301X-fix-duplex-full-full-duplex.patch[6]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=02474292a44205c1eb5a03634ead155a3c9134f4
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=86b93cbfe104e99fd3d25a49748b99fb88101573
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=79b9ab357b6f5675007f4c02ff8765cbd8dc06a2
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=d528faa9e828b9fc46dfb684a2a9fd8c2e860ed8
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=5899bc4058e89d5110a23797ff94439c53b77c25
6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=95afd2c7c7d26087730dc938709e025a303e5499

Build system: x86/64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Co-authored-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Audia <therealgraysky@proton.me>
[rebased ipq40xx/patches-5.15/902-dts-ipq4019-ap-dk04.1.patch ]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-07-30 18:02:47 +02:00
Shiji Yang
96010bb17c ramips: mt7621-wdt: use phandle to access system controller registers
These patches allow the driver to access some watchdog registers via a
phandle to the system controller node[1]. To apply these changes, we
need to add "mediatek,sysctl" to the SoC dtsi. This commit also remove
the redundent clocks, interrupts and resets properties.

[1] https://lore.kernel.org/all/20230214103936.1061078-2-sergio.paracuellos@gmail.com

Tested on Motorola MWR03 (MT7628)

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-07-30 13:09:23 +02:00
Shiji Yang
1f818b09f8 ramips: add proper system clock and reset driver support for legacy SoCs
This series of upstream patches properly implement a clock and reset
driver for old ralink SoCs[1]. And it includes some related fixes[2] and
improvements[3][4]. All patches have been merged into linux-next. They
will be part of upcoming Linux 6.5. In order to switch to the new system
controller driver, all clocks and resets properties in SoC dtsi have been
updated, and kernel symbol "CONFIG_CLK_MTMIPS" have been added to the
kernel config files.

[1] https://lore.kernel.org/all/20230619040941.1340372-1-sergio.paracuellos@gmail.com
[2] https://lore.kernel.org/all/20230622-mips-ralink-clk-wuninitialized-v1-1-ea9041240d10@kernel.org
[3] https://lore.kernel.org/all/OSYP286MB03120BABB25900E113ED42B7BC5CA@OSYP286MB0312.JPNP286.PROD.OUTLOOK.COM
[4] https://lore.kernel.org/all/TYAP286MB03151148AF8C054621DD55C3BC23A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM

Tested on Motorola MWR03 (MT7628)
Tested on Haier HW-L1W (MT7620)

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-07-30 13:09:23 +02:00
Shiji Yang
8cacf2bda8 ramips: add proper system clock and reset driver support for mt7621
This series of upstream patches makes the system controller node as a
reset provider[1][2], and it also includes some clock and reset driver
fixes[3][4]. Meanwhile, all clocks and resets properties in the SoC
device tree have been updated to be compatible with the new driver.

[1] https://lore.kernel.org/r/20220110114930.1406665-2-sergio.paracuellos@gmail.com
[2] https://lore.kernel.org/r/20220210094859.927868-2-sergio.paracuellos@gmail.com
[3] https://lore.kernel.org/r/20221217074806.3225150-1-sergio.paracuellos@gmail.com
[4] https://lore.kernel.org/r/20230206083305.147582-1-sergio.paracuellos@gmail.com

Tested on RAISECOM MSG1500 X.00

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-07-30 13:09:23 +02:00
Shiji Yang
b4ea49ad44 ramips: pinctrl: support requesting different functions for same group
MT7620 wireless radio needs change the pin group function between
"gpio" and "pa" during the calibration process. However, ralink
pinctrl driver doesn't support requesting different functions for
the same group. This patch enables pinctrl consumers to perform
such operations.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-07-29 15:07:11 +01:00
Rafał Miłecki
03b3284805 ramips: use NVMEM cells with mt76 EEPROM for Netgear R6220 & WNDR3700 v5
This uses new upstream DT binding. It's more generic (NVMEM) compared to
the old one (MTD).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-07-28 19:42:46 +02:00
Rafał Miłecki
e6cf959d0e ramips: use fixed layout cell "mac-base" for Netgear WNDR3700 v5
This drops a use of downstream "mac-address-increment".

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-07-28 18:50:39 +02:00
Felix Fietkau
a110de8152 kernel: drop mips highmem offset start overrides
The maximum offset that can be supported is 0x20000000
Do not override it to to something bigger than that on MT7621, as that could
cause issues based on the fixed memory mappings. This makes the last 64 MB
RAM unusable on MT7621 devices with 512 MB but avoids incurring a heavy
performance hit

Fixes: cd2b74e01e ("ramips: mt7621: disable highmem support and remove highmem offset patch")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-07-24 14:45:29 +02:00
Felix Fietkau
cd2b74e01e ramips: mt7621: disable highmem support and remove highmem offset patch
On MT7621 it was observed, that enabling highmem support causes a significant
performance drop, as documented in: https://github.com/openwrt/openwrt/issues/13151
By adjusting the highmem start offset, we avoid leaving any RAM unaddressable,
even on devices with 512 MB

Fixes: https://github.com/openwrt/openwrt/issues/13151
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-07-24 13:36:39 +02:00
Rafał Miłecki
ab9153f2d9 ramips: replace "mac-address-ascii" with "mac-base"
With upstream accepted "mac-base" binding there is no need for a
downstream "mac-address-ascii" workaround anymore.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
[TP-Link EC330-G5u v1 - OK]
Tested-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-07-21 07:29:40 +02:00
Rafał Miłecki
be7f9ad4dd ramips: fix Ubiquiti EdgeRouter X's MAC address for gmac1
This fixes:
[    0.586649] OF: /ethernet@1e100000/mac@1: #nvmem-cell-cells = 1 found 0

Fixes: 28b6224104 ("ramips: use fixed layout cell "mac-base" for Ubiquiti EdgeRouter X")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-07-18 11:27:30 +02:00
Rafał Miłecki
28b6224104 ramips: use fixed layout cell "mac-base" for Ubiquiti EdgeRouter X
This drops a use of downstream "mac-address-increment".

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-07-14 11:38:12 +02:00
Rafał Miłecki
f1492fcc09 ramips: use fixed layout cell "mac-base" for Netgear R6220
This drops a use of downstream "mac-address-increment".

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-07-14 11:38:12 +02:00
Rafał Miłecki
42fbaf96cb ramips: set Netgear R6220 MAC NVMEM cell directly in the part node
There is no need to use reference if original node it specified in
exactly the same file. This is a minor cleanup simplifying DTS code.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-07-14 11:38:12 +02:00
Arınç ÜNAL
8bf9a8a5e6 ramips: add wan2 support for MQmaker WiTi
The PHY of the wan2 port on MQmaker WiTi is wired to the second MAC of the
SoC. Rename the wan interface to wan1 and define it under the switch node,
effectively disabling the PHY muxing of the MT7530 switch's phy4.

Define the PHY of the wan2 port and adjust the gmac1 node accordingly. Now
that the PHY muxing feature is not being used anymore, the wan2 port can be
used to achieve 2 Gbps total bandwidth to the CPU.

Tested-by: Demetris Ierokipides <ierokipides.dem@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-07-12 20:36:32 +02:00
Arınç ÜNAL
50ecca74cb ramips: rename to GnuBee GB-PC1 and GnuBee GB-PC2
Rename GB-PC1 to GnuBee GB-PC1, and GB-PC2 to GnuBee GB-PC2. Let's not make
naming exceptions because of marketing whims.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-07-12 20:36:32 +02:00
Sander Vanheule
11588c52b4 ramips: mt7621: add TP-Link EAP613 v1
The TP-Link EAP613 v1 is a ceiling-mount 802.11ax access point. It can
be powered via PoE or a DC barrel connector (12V). Connecting to the
UART requires fine soldering and careful manipulation of any soldered
wires.

Device details:
  * SoC: MT7621AT
  * Flash: 16 MiB SPI NOR
  * RAM: 256 MiB DDR3L
  * Wi-Fi:
    * MT7905DA + MT7975D: 2.4 GHz + 5 GHz (DBDC), 2x2:2
    * Two stamped metal antennas (ANT1, ANT2)
    * One PCB antenna (ANT3)
    * One unpopulated antenna (ANT4)
  * Ethernet:
    * 1× 10/100/1000 Mbps port with PoE
  * LEDs:
    * Array of four blue LEDs with one control line
  * Buttons:
    * Reset
  * Board test points:
    * UART: next to CPU RF-shield and power circuits
    * JTAG: under CPU RF-shield (untested)
  * Watchdog: 3PEAK TPV706 (not implemented)

  Althought three antennas are populated, the MT7905DA does not support
  the additional Rx chain for background DFS detection (or Bluetooth)
  according to commit 6cbcc34f50 ("ramips: disable unsupported
  background radar detection").

MAC addresses:
  * LAN: 48:22:54:xx:xx:a2 (device label)
  * WLAN 2.4 GHz: 48:22:54:xx:xx:a2
  * WLAN 5 GHz: 48:22:54:xx:xx:a3

  The radio calibration blob stored in flash also contains valid MAC
  addresses for both radio bands (OUI 00:0c:43).

Factory install:
  1. Enable SSH on the device via web interface
  2. Log in with SSH, and run `cliclientd stopcs`
  3. Upload -factory.bin image via web interface. It may be necessary to
     shorten the filename of the image to e.g. 'factory.bin'.

Recovery:
  1. Open the device by unscrewing four screws from the backside
  2. Carefully remove board from the housing
  3. Connect to UART (3.3V):
    * Find test points labelled "VCC", "GND", "UART_TX", "UART_RX"
    * Solder wires to test points or connect otherwise. Be careful not
      to damage the PCB e.g. by pulling on soldered wires.
    * Open console with 115200n8 settings
  4. Interrupt bootloader and use tftpboot to start an initramfs:
        setenv ipaddr $DEVICE_IP
        setenv serverip $SERVER_IP
        tftpboot 84000000 openwrt-initramfs-kernel.bin
        bootm

  DO NOT use saveenv to store modified u-boot environment variables. The
  environment is saved at flash offset 0x30000, which erases part of the
  (secondary) bootloader.

  The device uses two bootloader stages. The first stage will load the
  second stage from a uImage stored at flash offset 0x10000. In case of
  a damaged second stage, the first stage should allow uploading a new
  image via y-modem (untested).

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2023-07-02 22:14:05 +02:00
Usama Nassir
f24c9b9d86 ramips: Add support for ComFast CF-E390AX
Add support for ComFast CF-E390AX. It is a 802.11 wifi6 cieling AP, based on MediaTek MT7261AT.

Specifications:
SoC: MediaTek MT7621AT
RAM: 128 MiB
Flash: 16 MiB NOR (Macronix mx25l12805d)

Wireless: MT7915E (2.4G) 802.11ax/b/g/n MT7915E (5G) 802.11ac/ax/n
Ethernet: 2 x 1Gbs
Button: 1 x "Reset" button
LED: 1x Blue LED + 1x Red LED + 1x green LED
Power: PoE

Manufacturer Page:
http://en.comfast.com.cn/index.php?m=content&c=index&a=show&catid=84&id=75

Flash Layout:
0x000000000000-0x000000030000 : "bootloader"
0x000000030000-0x000000040000 : "config"
0x000000050000-0x000000060000 : "factory"
0x000000090000-0x000001000000 : "firmware"

First install:
1. Set device into http firmware fail safe upload mode by pressing the reset button for 10 seconds while powering
   it on. Once the LED stops flashing, safe mode will be running.
2. Set PC IP address to 192.168.1.2
3. Browse to 192.168.1.1 and upload the factory image using the web interface.

Signed-off-by: Usama Nassir <usama.nassir@gmail.com>
2023-07-01 16:18:55 +02:00
Mikhail Zhilkin
2d6784a033 ramips: add support for Sercomm S1500 devices
This commit adds support for following wireless routers:
 - Beeline SmartBox PRO (Serсomm S1500 AWI)
 - WiFire S1500.NBN (Serсomm S1500 BUC)

This commit is based on this PR:
 - Link: https://github.com/openwrt/openwrt/pull/4770
 - Author: Maximilian Weinmann <x1@disroot.org>
The opening of this PR was agreed with author.

My changes:
- Sorting, minor changes and some movings between dts and dtsi
- Move leds to dts when possible
- Recipes for the factory image
- Update of the installation/recovery/return to stock guides
- Add reset GPIO for the pcie1

Common specification
--------------------
SoC:        MediaTek MT7621AT (880 MHz, 2 cores)
Switch:     MediaTek MT7530 (via SoC MT7621AT)
Wireless:   2.4 GHz, MT7602EN, b/g/n, 2x2
Wireless:   5 GHz, MT7612EN, a/n/ac, 2x2
Ethernet:   5 ports - 5×GbE (WAN, LAN1-4)
Mini PCIe:  via J2 on PCB, not soldered on the board
UART:       J4 -> GND[], TX, VCC(3.3V), RX
BootLoader: U-Boot SerComm/Mediatek

Beeline SmartBox PRO specification
----------------------------------
RAM (Nanya NT5CB128M16FP): 256 MiB
NAND-Flash (ESMT F59L2G81A): 256 MiB
USB ports: 2xUSB2.0
LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP)
Power: 12 VDC, 1.5 A
PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0
CSN: SG15********
MAC LAN: 94:4A:0C:**:**:**
Manufacturer's code: 0AWI0500QW1

WiFire S1500.NBN specification
------------------------------
RAM (Nanya NT5CC64M16GP): 128 MiB
NAND-Flash (ESMT F59L1G81MA): 128 MiB
USB ports: 1xUSB2.0
LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (RESET, WPS)
Power: 12 VDC, 1.0 A
PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0
CSN: MH16********
MAC WAN: E0:60:66:**:**:**
Manufacturer's code: 0BUC0500RW1

MAC address table (PRO)
-----------------------
use   address   source
LAN   *:23      factory 0x1000 (label)
WAN   *:24      factory $label +1
2g    *:23      factory $label
5g    *:25      factory $label +2

MAC addresses (NBN)
-------------------
use   address   source
LAN   *:0e      factory 0x1000
WAN   *:0f      LAN +1 (label)
2g    *:0f      LAN +1
5g    *:10      LAN +2

OEM easy installation
---------------------
1. Remove all dots from the factory image filename (except the dot
   before file extension)
2. Upload and update the firmware via the original web interface
3. Two options are possible after the reboot:
   a. OpenWrt - that's OK, the mission accomplished
   b. Stock firmware - install Stock firmware (to switch booflag from
      Sercomm0 to Sercomm1) and then OpenWrt factory image.

Return to Stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
   printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2
   reboot
2. Install stock firmware via the web OEM firmware interface

Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery

Tested-by: Pavel Ivanov <pi635v@gmail.com>
Tested-by: Denis Myshaev <denis.myshaev@gmail.com>
Tested-by: Oleg Galeev <olegingaleev@gmail.com>
Tested-By: Ivan Pavlov <AuthorReflex@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-07-01 16:05:01 +02:00
Mikhail Zhilkin
f560be583a ramips: sercomm.mk: preparation for Sercomm s1500 devices support
This commit moves a part of the code from the "sercomm-factory-cqr" recipe
to the separate "sercomm-mkhash" recipe. This simplifies recipes and
allows insert additional recipes between these code blocks (required for
the future support for Beeline SmartBox PRO router).

dd automatically fills the file by 0x00 if the filesize is less than
offset where we start writing. We drop such dd command so we need to add
--extra-padding-size 0x190 to the sercomm-pid.py call.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-07-01 16:05:01 +02:00
Wenli Looi
32ea8a9a7e ramips: add support for Netgear EAX12 series
Netgear EAX12, EAX11v2, EAX15v2 are wall-plug 802.11ax (Wi-Fi 6)
extenders that share the SoC, WiFi chip, and image format with the
WAX202.

Specifications:
* MT7621, 256 MiB RAM, 128 MiB NAND
* MT7915: 2.4/5 GHz 2x2 802.11ax (DBDC)
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)

All LEDs and buttons appear to work without state_default.

Installation:
* Flash the factory image through the stock web interface, or TFTP to
  the bootloader. NMRP can be used to TFTP without opening the case.

Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.

References in GPL source:
https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz

* target/linux/ramips/dts/mt7621-rfb-ax-nand.dts
  DTS file for this device.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2023-07-01 14:42:11 +02:00
Wenli Looi
0a1ebccc87 image: add additional fields to Netgear encrypted image
These fields are used for EAX12 and EX6250v2 series, and perhaps other
devices. Compatibility is preserved with the WAX202 and WAX206.

In addition, adds the related vars to DEVICE_VARS so that the variables
work correctly with multiple devices.

References in GPL source:
https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz

* tools/imgencoder/src/gj_enc.c
  Contains code that generates the encrypted image.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2023-07-01 14:42:11 +02:00
Robert Marko
39b2251cd9 treewide: remove CONFIG_FRAME_WARN from kernel configs
CONFIG_FRAME_WARN is set dynamically, so there is no need for it to be set
in target kernel configs, so lets remove it from all configs.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-07-01 11:53:21 +02:00
Felix Fietkau
dc38199b96 ramips/mt7621: disable the cpufreq driver
It causes a noticeable performance decrease

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-06-30 14:46:49 +02:00
Shiji Yang
285f0668f4 ramips: do not print error log when mdio bus is disabled
The mdio bus is used to control externel switch. In most cases, they are
disabled, which is the normal behavior. Treating this as an error makes
no sense, so we need to change the notification level from error to info.

Fixes: a2acdf9607 ("ramips: mt7620: remove useless GMAC nodes")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-06-25 18:48:29 +02:00
Shiji Yang
4e74777fa8 ramips: backport upstream mt762x PCIe driver error log fixes
These patches silence some mt762x PCIe driver error messeges by removing
the useless debugging codes and replacing incorrectly used 'dev_err()'
with 'dev_info()':

PCI: mt7621: Use dev_info() to log PCIe card detection [1]
mips: pci-mt7620: do not print NFTS register value as error log [2]
mips: pci-mt7620: use dev_info() to log PCIe device detection result [3]

Patch [1] has already been merged into the Linux 6.3 branch. Patches [2] and
[3] have been merged into the "mips-next" tree, and they will be part of the
upcoming Linux 6.5.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?h=v6.4-rc7&id=50233e105a0332ec0f3bc83180c416e6b200471e
[2] https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=9f9a035e6156a57d9da062b26d2a48d031744a1e
[3] https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=89ec9bbe60b61cc6ae3eddd6d4f43e128f8a88de

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-06-25 18:48:24 +02:00
Alexey Bartenev
ce998cb6e1 ramips: add support for D-Link DIR-806A B1 router
General specification:
SoC Type: MediaTek MT7620A (580MHz)
ROM: 8 MB SPI-NOR (MX25L6406E)
RAM: 64 MB DDR (W9751G6KB-25)
Switch: MediaTek MT7530
Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
Wireless: 2.4 GHz (MediaTek RT5390): b/g/n
Wireless: 5 GHz (MediaTek MT7610EN): ac/n
Buttons: 2 button (POWER, WPS/RESET)
Bootloader: U-Boot 1.1.3
Power: 12 VDC, 0.5 A

MACs:
| LAN	| [Factory + 0x04] - 2		|
| WLAN 2.4g	| [Factory + 0x04] - 1		|
| WLAN 5g	| [Factory + 0x8004] - 3	|
| WAN	| [Factory + 0x04] - 2		|

OEM easy installation:

1. Use a PC to browse to http://192.168.0.1.
2. Go to the System section and open the Firmware Update section.
3. Under the Local Update at the right, click on the CHOOSE FILE...
4. When a modal window appears, choose the firmware file and click on
 the Open.
5. Next click on the UPDATE FIRMWARE button and upload the firmware image.
Wait for the router to flash and reboot.

OEM installation using the TFTP method (need level converter):

1. Download the latest firmware image.
2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the firmware
 image to the root directory of the server.
3. Power off the router and use a twisted pair cable to connect the PC
 to any of the router's LAN ports.
4. Configure the network adapter of the PC to use IP address 192.168.0.180
 and subnet mask 255.255.255.0.
5. Connect serial port (57600 8N1) and turn on the router.
6. Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2: Load
 system code then write to Flash via TFTP.").
7. Press Y key when show "Warning!! Erase Linux in Flash then burn new
 one. Are you sure? (Y/N)"
Input device IP (192.168.0.1) ==:192.168.0.1
Input server IP (192.168.0.180) ==:192.168.0.180
Input Linux Kernel filename () ==:firmware_name
The router should download the firmware via TFTP and complete flashing in
 a few minutes.
After flashing is complete, use the PC to browse to http://192.168.1.1 or
 ssh to proceed with the configuration.

Signed-off-by: Alexey Bartenev <41exey@proton.me>
2023-06-25 16:25:01 +02:00
Stefan Weil
8d06bc1751 ramips: add Edimax BR-6208AC V2 support
Specifications:
- Device: Edimax BR-6208AC V2
- SoC: MT7620A
- Flash: 16 MiB
- RAM: 64 MiB
- Switch: 1 WAN, 3 LAN (10/100 Mbps)
- WiFi: MT7620 2.4 GHz + MT7610E 5 GHz
- LEDs: 1x POWER (green, not configurable)
        1x Firmware (green, configurable)
        1x Internet (green, configurable)
        1x VPN (green, configurable)
        1x 2.4G (green, not configurable)
        1x 5G (green, not configurable)

Normal installation:
- Upload the sysupgrade image via the default web interface

Installation with U-Boot and TFTP:
- Requires a TFTP server which provides the sysupgrade image
- Requires a connection to the serial port of the device, rate 57600

Signed-off-by: Stefan Weil <sw@weilnetz.de>
2023-06-25 13:58:26 +02:00
Davide Fioravanti
c71dada926 ramips: fix lan leds for Wavlink WL-WN535K1
Previously both lan1 and lan2 leds were wrongly labelled as lan2.
Moreover they were connected to the wrong lan port.
Fixes 8fde82095b ("ramips: add support for Wavlink WL-WN535K1")

Reported-by: Nicolò Maria Semprini <nicosemp@gmail.com>
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2023-06-25 11:02:04 +02:00
John Audia
1f5fce27c1 kernel: bump 5.15 to 5.15.118
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-06-23 23:05:45 +02:00
Kim DoHyoung
0bbd5699c8 ramips: mt7621: add support for Zbtlink ZBT-WG1608 (32M)
Zbtlink ZBT-WG1608 is a Wi-Fi router intendent to use with WWAN (4G/5G)
modems.

Specifications:
* SoC: MediaTek MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB (SPI NOR)
* Wi-Fi:
  * MediaTek MT7603E : 2.4Ghz
  * MediaTek MT7613BE : 5Ghz
* Ethernet: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* M.2: 1x slot with USB&SIM
  * EM7455/EM12-G/EM160R/RM500Q-AE
* USB: 1x 3.0 Type-A port
* External storage: 1x microSD (SDXC) slot
* UART: console (115200 baud)
* LED:
  * 1 power indicator
  * 1 WLAN 2.4G controlled (wlan 2G)
  * 3 SoC controlled (wlan 5G, wwan, internet)
  * 5 per Eth phy (4xLAN + WAN)

MAC Addresses:
* LAN    : f8:5e:3c:xx:xx:e0 (Factory, 0xe000 (hex))
* WAN    : f8:5e:3c:xx:xx:e1 (Factory, 0xe006 (hex))
* 2.4 GHz: f8:5e:3c:xx:xx:de (Factory, 0x0004 (hex))
* 5 GHz  : f8:5e:3c:xx:xx:df (Factory, 0x8004 (hex))

Installation:
* Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can
  be directly used to install OpenWrt. Firmware must be upgraded using the
  'force' and 'do not save configuration' command line options (or
  correspondig web interface checkboxes) since the vendor firmware is from
  the pre-DSA era.

Recovery Mode:
 * Press reset button, power up the device, wait for about 10sec.
 * Upload sysupgrade image through the firmware recovery mode web page at
  192.168.1.1.

Signed-off-by: Kim DoHyoung <azusahmr@k-on.kr>
2023-06-20 21:48:23 +08:00
Russell Morris
1d6e594aa0 ramips: sunvalley - allow larger sysupgrade
Aligned to size of mtd-concat partition (firmware)
  - in this device we have mtd-concat driver that joins multiple flash partitions
  - since sysupgrade works with mtd devices the rootfs partition is already joined
  - we can use a bigger sysupgrade image than factory/TFTP install images
Checked on hardware, no issues seen.
No modifications to images other than sysupgrade (i.e. TFTP / recovery images not touched).

Signed-off-by: Russell Morris <rmorris@rkmorris.us>
2023-06-20 21:23:58 +08:00
John Audia
5dc78d8f18 kernel: bump 5.15 to 5.15.116
All patches rebased automatically.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-06-12 20:39:38 +02:00
Volodymyr Puiul
47c2d50c03 ramips: mt7621-dts: move wan port to gmac1 YunCore FAP-640
move wan port to gmac1 to achieve 2Gbps CPU bandwidth between wan and
lan on YunCore FAP-640

Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
2023-06-11 18:16:39 +02:00
Maximilian Weinmann
8fcfb21b16 ramips: Add support for Beeline SmartBox TURBO+
This adds support for Beeline Smart Box TURBO+ (Serсomm S3 CQR) router.

Device specification
--------------------
SoC Type: MediaTek MT7621AT (880 MHz, 2 cores)
RAM (Nanya NT5CC64M16GP): 128 MiB
Flash (Macronix MX30LF1G18AC): 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615N): a/n/ac, 4x4
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
USB ports: 1xUSB3.0
Buttons: 2 button (reset, wps)
LEDs: Red, Green, Blue
Zigbee (EFR32MG1B232GG): 3.0
Stock bootloader: U-Boot 1.1.3
Power: 12 VDC, 1.5 A

Installation (fw 2.0.9)
-----------------------
1.  Login to the web interface under SuperUser (root) credentials.
    Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the
    device written on the backplate stick.
2.  Navigate to Setting -> WAN. Add:
       Name - WAN1
       Connection Type - Static
       IP Address - 172.16.0.1
       Netmask - 255.255.255.0
    Save -> Apply. Set default: WAN1
3.  Enable SSH and HTTP on WAN. Setting -> Remote control. Add:
       Protocol - SSH
       Port - 22
       IP Address - 172.16.0.1
       Netmask - 255.255.255.0
       WAN Interface - WAN1
    Save ->Apply
    Add:
       Protocol - HTTP
       Port - 80
       IP Address - 172.16.0.1
       Netmask - 255.255.255.0
       WAN interface - WAN1
    Save -> Apply
4.  Set up your PC ethernet:
       Connection Type - Static
       IP Address - 172.16.0.2
       Netmask - 255.255.255.0
       Gateway - 172.16.0.1
5.  Connect PC using ethernet cable to the WAN port of the router
6.  Connect to the router using SSH shell under SuperUser account
7.  Make a mtd backup (optional, see related section)
8.  Change bootflag to Sercomm1 and reboot:
        printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
        reboot
9.  Login to the router web interface under admin account
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image

Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
   printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3

mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
      cd /tmp
      for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
      tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
      tftp -l mtd.md5 -p 171.16.0.2

Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery

MAC Addresses (fw 2.0.9)
------------------------
+-----+------------+---------+
| use | address    | example |
+-----+------------+---------+
| LAN | label      | *:e8    |
| WAN | label + 1  | *:e9    |
| 2g  | label + 4  | *:ec    |
| 5g  | label + 5  | *:ed    |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000

Factory image format
--------------------
+---+-------------------+-------------+--------------------+
| # | Offset            | Size        | Description        |
+---+-------------------+-------------+--------------------+
| 1 | 0x0               | 0x200       | Tag Header Factory |
| 2 | 0x200             | 0x100       | Tag Header Kernel1 |
| 3 | 0x300             | 0x100       | Tag Header Kernel2 |
| 4 | 0x400             | SIZE_KERNEL | Kernel             |
| 5 | 0x400+SIZE_KERNEL | SIZE_ROOTFS | RootFS(UBI)        |
+---+-------------------+-------------+--------------------+

Co-authored-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
2023-06-11 13:36:38 +08:00
Arınç ÜNAL
b61253f92a ramips: fix first boot network configuration for TOZED ZLT S12 PRO
The network configuration at first boot for TOZED ZLT S12 PRO lacks setting
up the LAN and WAN network interfaces. Address this. The WAN port is
advertised as WAN/LAN on the device and is put on LAN on stock firmware so
put it on LAN here as well.

Fixes: ce1f9fa625 ("ramips: add support for TOZED ZLT S12 PRO")
Reported-by: Andre Cruz <me@1conan.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-06-09 22:28:45 +02:00
Thomas Schröder
b0120f7c8b ramips: fix button definitions for Zyxel WSM20
Setting the events of the WPS and LED buttons to
the best matching values based from the documentation:
<https://openwrt.org/docs/guide-user/hardware/hardware.button#procd_buttons>

Signed-off-by: Thomas Schröder <tschroeder_github@outlook.com>
2023-06-09 22:28:45 +02:00
Mikhail Zhilkin
d955b41275 ramips: enable LED button for TP-Link EC330-G5u v1
The device already has LED push button (KEY_LIGHTS_TOGGLE)
and exported GPIO control "led-light". This commit adds
button handler script for switching on/off all device LEDs.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2023-06-08 17:25:22 +02:00
Christian Marangi
0a4b309f41
generic: backport initial LEDs hw control support
Backport initial LEDs hw control support. Currently this is limited to
only rx/tx and link events for the netdev trigger but the API got
accepted and the additional modes are working on and will be backported
later.

Refresh every patch and add the additional config flag for QCA8K new
LEDs support.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-06-06 11:01:31 +02:00
Daniel Danzberger
29a5cb7a8b
ramips: fix lzma-loader for ASIARF boards
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.

Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
2023-06-05 10:01:27 +02:00
Andreas Böhler
46b51e9e99 ramips: tplink,mr600v2: fix image generation for sysupgrade image
The MR600v2 does not find its rootfs if it is neither directly after the
kernel or aligned to an erase block boundary (64k).

This aligns the rootfs to 0x10000 allowing the device to boot again. Based
on investigation by forum user relghuar.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-06-03 21:14:37 +02:00
Daniel Golle
ba58245e83 mediatek: sync MT7988 USXGMII with SDK driver
The USXGMII driver in SDK was heavily refactored, some bugs have been
fixed and it has switched to use phylink_pcs. Follow up with changes
in SDK driver and sync our on-top-of-mainline driver with the SDK
driver.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-05-27 21:57:01 +01:00
Nick Hainke
2388b119de ramips: mark patches accepted upstream
Add kernel tags to the patches that got accepted upstream.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-05-26 16:22:11 +02:00
Daniel Golle
958fdf36e3 generic: mt7530: backport support for the MT7988 built-in switch
Backport commits adding support for the MT7988 built-in switch to the
mt7530 driver.

This change results in the Kconfig symbol NET_DSA_MT7530 to be extended
by NET_DSA_MT7530_MDIO (everything formally covered by NET_DSA_MT7530)
and NET_DSA_MT7530_MMIO (a new driver for the MMIO-connected built-in
switch of the MT7988 SoC).

Select NET_DSA_MT7530_MDIO for all targets previously selecting
NET_DSA_MT7530, with the exception of mediatek/filogic which also
selects NET_DSA_MT7530_MMIO.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-05-23 15:53:22 +01:00
Daniel Golle
6983a215d9 generic: add support for MediaTek NETSYS v3
In order to support Ethernet on the MT7988 SoC add support for NETSYS v3
as well as new paths and USXGMII SerDes to the mtk_eth_soc driver.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-05-23 15:53:22 +01:00
Shiji Yang
2fbb91d73f ramips: correct page read return value of the mt7621 nand driver
read_page() need to return maximum number of bitflips instead of the
accumulated number. Change takes from upstream mt7621 u-boot [1].

 * @read_page:  function to read a page according to the ECC generator
 *              requirements; returns maximum number of bitflips
 *              corrected in any single ECC step, -EIO hw error

[1] https://lore.kernel.org/all/cover.1653015383.git.weijie.gao@mediatek.com/

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-05-22 14:45:03 +02:00
Felix Baumann
f5cb556d4f treewide: Disable building 32M RAM devices
Following deprecation notice[1] in 21.02, disable targets with 32M of RAM

[1] https://openwrt.org/supported_devices/864_warning

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-05-21 01:08:22 +02:00
DENG Qingfang
09d0643c18 ramips: mt7621: fix Xiaomi Router 3G/Pro LEDs
The PHY name has been changed to "mt7530-0" since IRQ support
was added to MT7530 driver.

Fixes: f9cfe7af1f ("kernel: backport MT7530 IRQ support")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
(node names, added color, function+function-enumerator properties)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2023-05-20 23:24:50 +02:00
Aleksander Jan Bajkowski
7365e6b00a kernel: remove obsolete kernel version switches
This removes unneeded kernel version switches from the targets after
kernel 5.10 has been dropped.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2023-05-20 15:19:14 +02:00
Shiji Yang
ab7e251303 ramips: fix build error on Airlink AR670W
The 'KERNEL' is not referenced by other objects, so double '$$' will
cause shell unable to parse the variable 'BLOCKSIZE':
  dd ... bs=$(BLOCKSIZE) conv=sync
  bash: line 1: BLOCKSIZE: command not found

Fixes: 09a0efbe83(ramips: set default BLOCKSIZE to 64k for nor flash devices)
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-05-19 23:33:49 +02:00
Shiji Yang
b09a83808a ramips: add basic common recipe for nand flash devices
These same codes are repeated for many devices now, it's better to
move them to shared definition. This commit also add the missing
KERNEL_SIZE of the ZyXEL NR7101 and ZyXEL LTE3301-PLUS.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-05-18 16:46:16 +02:00
Shiji Yang
09a0efbe83 ramips: set default BLOCKSIZE to 64k for nor flash devices
In kernel 5.15, the default erase sector size of the nor flash has
been switched from 4k to 64k. This may cause the configuration not
be preserved across upgrades. To avoid this issue, change the default
BLOCKSIZE to 64k.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-05-18 16:46:16 +02:00
Shiji Yang
d343a15314 ramips: enable variable sector size erasure for all subtarget
Make use of minor sector size (4k) on supported flash chips to improve
spi read/write performance.

Tested on ramips/mt7628: Motorola MWR03

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-05-18 16:46:16 +02:00
Arınç ÜNAL
434dce0729 ramips: rename to D-Team Newifi D2 and Lenovo Newifi D1
Rename Newifi D2 to D-Team Newifi D2, and Newifi D1 to Lenovo Newifi D1.
Let's not make naming exceptions because of marketing whims.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-05-18 14:44:07 +02:00
Arınç ÜNAL
ce1f9fa625 ramips: add support for TOZED ZLT S12 PRO
The TOZED ZLT S12 PRO is an AC1200 router featuring 4 Ethernet ports with a
TOZED TL70-C cellular modem which supports the NCM mode.

The stock firmware does SIM locking on the modem by stopping dialing when a
different PLMN is detected. This is not the case on OpenWrt.

Specifications:
- CPU: MediaTek MT7621AT
- RAM: 256MB DDR3
- NOR Flash: MX25L12833FM2I 16MB SPI Flash
- Wi-Fi 2.4Ghz: MT7603E
- Wi-Fi 5Ghz: MT7612E
- Switch: MT7530 4x 1Gbit Ports
- WWAN: Unisoc SL8563 based TOZED TL70-C LTE CAT6 cellular modem
- USB: 1x optional USB2.0 external port
- Switches/Buttons: WPS, Reset, Power Switch
- LEDs: Power, Wi-Fi, Data, Signal 1-5, Phone

Installation and TFTP Recovery:
- Connect to serial console.
- Boot initramfs image by choosing option 1 when U-Boot prompts.
- Install sysupgrade image via OpenWrt.

Serial Pins:
Located at the bottom right when looking from the front, right under the
Reset/WPS buttons. The pinout from the left is:
- RX
- GND
- TX
Baudrate is 115200.

When connecting from a powered off state, disconnect RX as it blocks the
boot process.

Link: http://www.sztozed.com/en/contents/58/84.html
Co-developed-by: Andre Cruz <me@1conan.com>
Signed-off-by: Andre Cruz <me@1conan.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-05-18 14:44:07 +02:00
Muhammad AL-Qadhy
97a37288b9 ramips: Fix Wireless Frequencies for HYC-G920
Fix wireless frequencies to show correct wireless interfaces.

Signed-off-by: Muhammad AL-Qadhy <m.ismael@gmail.com>
2023-05-18 12:02:15 +02:00
Nick Hainke
1fda304d8e
ramips: remove device tree legacy compatibility
We switched to 5.15 kernel, so we don't need to maintain 5.10
compatibility anymore.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-05-12 13:02:44 +02:00
Nick Hainke
1d3e71bd97
treewide: remove files for building 5.10 kernel
All targets are bumped to 5.15. Remove the old 5.10 patches, configs
and files using:

  find target/linux -iname '*-5.10' -exec rm -r {} \;

Further, remove the 5.10 include.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-05-12 13:02:43 +02:00
Christian Marangi
da2f5e8776
ramips: 5.15: add patch fixing compilation warning for hsdma-mt7621
Add patch fixing compilation warning for hsdma-mt7621:
drivers/staging/mt7621-dma/hsdma-mt7621.c: In function 'mtk_hsdma_probe':
drivers/staging/mt7621-dma/hsdma-mt7621.c:685:9: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result]
  685 |         device_reset(&pdev->dev);
      |         ^~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-05-12 03:15:39 +02:00
Christian Marangi
82afdf6056
ralink: rt3833: fix compilation warning from device_reset in fe_probe
Fix compilation warning from device_reset in fe_probe. On fail print a
warning but don't fail probe.
Fix compilation warning:
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_probe':
drivers/net/ethernet/ralink/mtk_eth_soc.c:1564:9: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result]
 1564 |         device_reset(&pdev->dev);
      |         ^~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-05-12 03:15:39 +02:00
Christian Marangi
4ea21e3161
ralink: mt76x8: fix compilation warning in esw driver
Fix compilation warning for debug string in esw driver:
drivers/net/ethernet/ralink/esw_rt3050.c:1535:9: note: in expansion of macro 'dev_info'
 1535 |         dev_info(&pdev->dev, "mediatek esw at 0x%08lx, irq %d initialized\n",
      |         ^~~~~~~~
drivers/net/ethernet/ralink/esw_rt3050.c:1535:53: note: format string is defined here
 1535 |         dev_info(&pdev->dev, "mediatek esw at 0x%08lx, irq %d initialized\n",
      |                                                 ~~~~^
      |                                                     |
      |                                                     long unsigned int
      |                                                 %08p
cc1: all warnings being treated as errors

Fix unused variable causing compilation warning:
drivers/net/ethernet/ralink/esw_rt3050.c: In function 'esw_interrupt':
drivers/net/ethernet/ralink/esw_rt3050.c:769:13: error: unused variable 'i' [-Werror=unused-variable]
  769 |         int i;
      |             ^
cc1: all warnings being treated as errors

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-05-12 03:15:39 +02:00
Christian Marangi
3fa87858a7
ramips: mtk-mcc: move cmd_buf for dbg under ifdef
Move cmd_buf for dbg under ifdef to fix compilation warning:
drivers/mmc/host/mtk-mmc/dbg.c:51:13: error: 'cmd_buf' defined but not used [-Werror=unused-variable]
   51 | static char cmd_buf[256];
      |             ^~~~~~~
cc1: all warnings being treated as errors

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-05-12 03:15:38 +02:00
Christian Marangi
aa7a2d971e
ralink: mt7620: fix compilation warning for device_reset in i2s driver
Fix compilation warning for device_reset in i2s driver.
Fix compilation warning:
sound/soc/ralink/ralink-i2s.c: In function 'ralink_i2s_probe':
sound/soc/ralink/ralink-i2s.c:885:9: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result]
  885 |         device_reset(&pdev->dev);
      |         ^~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errorralink: mt7620: fix compilation
warning for device_reset in i2s driver

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-05-12 03:15:38 +02:00
Christian Marangi
b786d744ef
ramips: 5.15: handle return from device_reset in I2C driver
Handle return from device reset in I2C driver. Don't fail on
device_reset error but print a warning.

Fix compilation warning:
sound/soc/ralink/ralink-i2s.c: In function 'ralink_i2s_probe':
sound/soc/ralink/ralink-i2s.c:885:9: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result]
  885 |         device_reset(&pdev->dev);
      |         ^~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-05-12 03:15:38 +02:00
Christian Marangi
7f54fa575b
ramips: mt7620: handle request_irq fail in gsw ethernet driver
Handle return from request_irq in gsw ethernet driver.
Fix compilation warning:
drivers/net/ethernet/ralink/gsw_mt7620.c: In function 'mtk_gsw_init':
drivers/net/ethernet/ralink/gsw_mt7620.c:236:17: error: ignoring return value of 'request_irq' declared with attribute 'warn_unused_result' [-Werror=unused-result]
  236 |                 request_irq(gsw->irq, gsw_interrupt_mt7620, 0,
      |                 ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  237 |                             "gsw", priv);
      |                             ~~~~~~~~~~~~
cc1: all warnings being treated as errors

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-05-12 03:15:37 +02:00
Christian Marangi
7a2a645801
ramips: 5.15: handle error from device_reset in SPI ralink driver
Handle error from device reset in SPI ralink driver fixing compilation
warning:

drivers/spi/spi-rt2880.c: In function 'rt2880_spi_probe':
drivers/spi/spi-rt2880.c:474:17: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result]
  474 |                 device_reset(&pdev->dev);
      |                 ^~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-05-12 03:15:33 +02:00
Christoph Krapp
e882af2850 ramips: add support for Linksys RE7000
Hardware specification:

- SoC: MediaTek MT7621AT (880 MHz)
- Flash: 16 MB (Macronix MX25L12835FM2I-10G)
- RAM: 128 MB (Nanya NT5CC64M16GP-DI)
- WLAN 2.4 GHz: 2x2 MediaTek MT7603EN
- WLAN 5 GHz: 2x2 MediaTek MT7615N
- Ethernet: 1x 10/100/1000 Mbps
- LED: Power, Wifi, WPS
- Button: Reset, WPS
- UART: 1:VCC, 2:GND, 3:TX, 4:RX (from LAN port)
  Serial console @ 57600,8n1

Flash instructions:

Connect to serial console and start up the device. As the bootloader got
locked you need to type in a password to unlock U-Boot access.
When you see the following output on the console:

relocate_code Pointer at: 87f1c000

type in the super secure password:

1234567890

Then select TFTP boot from RAM by selecting option 1 in the boot menu.
As Linksys decided to leave out a basic TFTP configuration you need to
set server- & client ip as well as the image filename the device will
search for. You need to use the initramfs openwrt image for the TFTP
boot process.

Once openwrt has booted up, upload the sysupgrade image via scp and run
sysupgrade as normal.

Signed-off-by: Christoph Krapp <achterin@gmail.com>
2023-05-09 11:52:53 +02:00
Maximilian Weinmann
36dd3ab7db ramips: fix dts file name for SNR-CPE-ME1
Rename file mt7621_snr_snr-spe-me-1.dts

Fixes: #12562
Fixes: ecdb248 ("ramips: add support for SNR-CPE-ME1")
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
2023-05-08 18:44:26 +02:00
Maximilian Weinmann
ecdb24814f ramips: add support for SNR-CPE-ME1
SNR-CPE-ME1 is a wireless WiFi 5 router manufactured by SNR/NAG company.

Specification:
    - SoC           : MediaTek MT7621A
    - RAM           : DDR3 256 MiB
    - Flash         : SPI-NOR 16 MiB (GD25Q128CSIG)
    - WLAN          : 2.4 GHz (MediaTek MT7603EN)
                      5 GHz (MediaTek MT7610EN)
    - Ethernet      : 10/100/1000 Mbps x5
      - Switch      : MediaTek MT7530 (in SoC)
    - USB           : 3.0 x1
    - UART          : through-hole on PCB
      - [J4] 3.3V, RX, TX, GND (57600n8)
    - Power         : 12 VDC, 2 A

Flash instruction via TFTP:
    1. Boot SNR-CPE-ME1 to recovery mode
        (hold the reset button while power on)
    2. Send firmware via TFTP client:
       TFTP Server address: 192.168.1.1
       TFTP Client address: 192.168.1.131
    3. Wait ~120 seconds to complete flashing
    4. Do sysupgrade using web-interface

Signed-off-by: Maximilian Weinmann <x1@disroot.org>
2023-05-07 14:44:54 +02:00
Felix Baumann
ed1217eac1 ramips: mt7621: rename Asus RT-AC57U to v1
rename RT-AC57U to avoid confusion with unsupported revisions 2 and 3

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-05-06 20:55:59 +02:00
Felix Baumann
e38de40f8d ramips: mt7621: add support for Cudy X6 v2
Rename existing device to v1 and create common .dtsi
Difference to v1: 16MB Flash

Specifications:

SoC: MediaTek MT7621
RAM: 256 MB
Flash: 16 MB (SPI NOR, XM25QH128C on my device)
WiFi: MediaTek MT7915E
Switch: 1 WAN, 4 LAN (Gigabit)
Buttons: Reset, WPS
LEDs: Two Power LEDs (blue and red; together they form purple)
Power: DC 12V 1A center positive
Serial: 115200 8N1
        C440 - (3V3 - GND - RX - TX) - C41 | v1 and v2
               (P   - G   - R  - T)        | v2 labels them on the board
Installation:

Download and flash the manufacturer's built OpenWrt image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWrt image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings.

Recovery:

Loads only signed manufacture firmware due to bootloader RSA verification
Serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
Connect to any lan ethernet port
Power on the device while holding the reset button
Wait at least 8 seconds before releasing reset button for image to
download

MAC addresses as verified by OEM firmware:

use   address             source
LAN   f4:a4:54:86:75:a2   label
WAN   f4:a4:54:86:75:a3   label + 1
2g    f4:a4:54:86:75:a2   label
5g    f6:a4:54:b6:75:a2   label + LA-Bit set + 4th oktet increased

The label MAC address is found in bdinfo 0xde00.

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-05-02 18:24:52 +02:00
Mikhail Zhilkin
4a043dc9d4 ramips: add factory image for TP-Link EC330-G5u v1
This commit adds factory.bin image for TP-Link EC330-G5u v1. This allows
to install OpenWrt without connecting a serial cable (UART).

Installation using factory image
--------------------------------

Tested with "3.16.0 0.9.1 v6037.0 Build 191016 Rel.30619nb" TP-Link
firmware.

1.  Login to the router web interface (http://192.168.0.1/ by default) and
    save running config to "conf.bin" file
2.  Open configuration file in any TP-Link config editor (e.g.
    https://jahed.github.io/tp-link-config-editor/)
3.  Find "DeviceInfo" section and insert a new string "<Description
    val="Modem Router`telnetd -p 1023 -l login`" />" according to the
    following example:
       <DeviceInfo>
          ...
          <Description val="Modem Router`telnetd -p 1023 -l login`" />
          ...
       </DeviceInfo>
4.  Save configuration file and upload changed configuration using stock
    firmware interface
5.  Login using telnet to IP:192.168.0.1 (Username:admin, password:1234)
6.  Run "cat /proc/mtd | grep mtd7"
       a. If the result is 'mtd7: 03000000 00020000 "rootfs" 03400000',
          then install stock firmware using web interface to toggle booted
          firmware image from "os1" to "os0"
       b. If the result is 'mtd7: 03000000 00020000 "rootfs" 00400000',
          then all is ok, go to the next step
7.  Set up a tftp server with OpenWrt factory.bin image (IP:192.168.0.100
    in this example)
8.  Login using telnet to 192.168.0.1
9.  Download OpenWrt factory.bin image from the tftp server:
       cd /tmp
       tftp -g -r factory.bin 192.168.0.100
10. Write OpenWrt factory.bin image:
       dd if=/tmp/factory.bin of=/dev/mtdblock1
11. Power cycle the router

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-04-29 22:34:51 +02:00
Mikhail Zhilkin
15e21d373b ramips: TP-Link EC330-G5u v1: switch to mac-address-ascii
The TP-Link EC330-G5u v1 router has MAC address that stored in factory mtd
in ascii format. This commit makes the router use of "mac-address-ascii"
in dts.

After the change:
1. All MAC addresses are explicitly assigned in dts (the workarounds in
   network scripts are no longer needed);
2. gmac0 (eth0) MAC address is no longer random.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-04-29 22:34:51 +02:00
Antonio Vázquez
c31319b669 ramips: lzma-loader: Refactor loader
* Delete unused lantiq makefile
* Delete redundant makefiles and unify them into the main makefile
* Refactor and unify board code into a single file
* Add support and review subtarget specific board support

Signed-off-by: Antonio Vázquez <antoniovazquezblanco@gmail.com>
2023-04-29 22:32:27 +02:00
Rani Hod
e4c7703d2a ramips: add support for D-Link DAP-1620 B1
The DAP-1620 rev B is a wall-plug AC1300 repeater.

Specifications:
- MT7621AT, 256 MiB RAM, 16 MiB SPI NOR
- MT7615DN 2x2 802.11n +2x2 802.11ac (DBDC)
- Ethernet: 1 port 10/100/1000
- Status LEDs (1x red+green)
- LED RSSI bargraph (2x green, 1x red+green)

Installation:
- Keep reset button pressed during plug-in
- Web Recovery Updater is at 192.168.0.50
- Upload factory.bin, confirm flashing
  (seems to work best with Chromium-based browsers)

Revert to OEM firmware:
- tail -c+117 DAP1620B1_FW212B03.bin | \
  openssl aes-256-cbc -d -md md5 -out decrypted.bin \
  -k 905503a4e0c3cd3c1ce062246de427a68962347e
- flash decrypted.bin via D-Link Web Recovery

Signed-off-by: Rani Hod <rani.hod@gmail.com>
2023-04-29 22:05:20 +02:00
Andreas Böhler
28df7f7ff2 ramips: mt7621: add support for ZyXEL WSM20
The ZyXEL WSM20 aka Multy M1 is a cheap mesh router system by ZyXEL
based on the MT7621 CPU.

Specifications
==============

SoC: MediaTek MT7621AT (880MHz)
RAM: 256MiB
Flash: 128MiB NAND
Wireless: 802.11ax (2x2 MT7915E DBDC)
Ethernet: 4x 10/100/1000 (MT7530)
Button: 1x WPS, 1x Reset, 1x LED On/Off
LED: 7 LEDs (3x white, 2x red, 2x green)

MAC address assignment
======================

The MAC address assignment follows stock: The label MAC address is the LAN
MAC address, the WAN address is read from flash.

The WiFi MAC addresses are set in userspace to label MAC + 1 and label MAC
+ 2.

Installation (web interface)
============================

The device is cloud-managed, but there is a hidden local firmware upgrade
page in the OEM web interface. The device has to be registered in the
cloud in order to be able to access this page.

The system has a dual firmware design, there is no way to tell which
firmware is currently booted. Therefore, an -initramfs version is flashed
first.

1. Log into the OEM web GUI
2. Access the hidden upgrade page by navigating to
   https://192.168.212.1/gui/#/main/debug/firmwareupgrade
3. Upload the -initramfs-kernel.bin file and flash it
4. Wait for OpenWrt to boot and log in via SSH
5. Transfer the sysupgrade file via SCP
6. Run sysupgrade to install the image
7. Reboot and enjoy

NB: If the initramfs version was installed in RAS2, the sysupgrade script
sets the boot number to the first partition. A backup has to be performed
manually in case the OEM firwmare should be kept.

Installation (UART method)
==========================

The UART method is more difficult, as the boot loader does not have a
timeout set. A semi-working stock firmware is required to configure it:

1. Attach UART
2. Boot the stock firmware until the message about failsafe mode appears
3. Enter failsafe mode by pressing "f" and "Enter"
4. Type "mount_root"
5. Run "fw_setenv bootmenu_delay 3"
6. Reboot, U-Boot now presents a menu
7. The -initramfs-kernel.bin image can be flashed using the menu
8. Run the regular sysupgrade for a permanent installation

Changing the partition to boot is a bit cumbersome in U-Boot, as there is
no menu to select it. It can only be checked using mstc_bootnum. To change
it, issue the following commands in U-Boot:

   nand read 1800000 53c0000 800
   mw.b 1800004 1 1
   nand erase 53c0000 800
   nand write 1800000 53c0000 800

This selects FW1. Replace "mw.b 1800004 1 1" by "mw.b 1800004 2 1" to
change to the second slot.

Back to stock
=============

It is possible to flash back to stock, but a OEM firmware upgrade is
required. ZyXEL does not provide the link on its website, but the link
can be acquired from the OEM web GUI by analyzing the transferred JSON
objects.

It is then a matter of writing the firmware to Kernel2 and setting the
boot partition to FW2:

   mtd write zyxel.bin Kernel2
   echo -ne "\x02" | dd of=/dev/mtdblock7 count=1 bs=1 seek=4 conv=notrunc

Signed-off-by: Andreas Böhler <dev@aboehler.at>
Credits to forum users Annick and SirLouen for their initial work on this
device
2023-04-29 21:53:34 +02:00
David Bauer
2c530fcb97 ramips: reduce Archer AX23 / MR70X SPI-frequency
It was brought to attention the Archer AX23 v1 fails to read jffs2 data
from time to time. While this is not reproducible on my unit, it is on
others.

Reducing the SPI frequency does the trick. While it worked with at lest
40 MHz, opt for the cautious side and choose a save frequency of 25 MHz.

Apply the same treatment to the Mercusys MR70X which uses a similar
design just in case.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-04-27 22:26:58 +02:00
Sebastian Schaper
0601f7134d ramips: fix green LED for D-Link DAP-X1860
It was found this device uses a single tri-color power/status LED
rather than individual red/orange LEDs, which also supports green.

Add GPIO for green color and use with `boot` and `running` aliases.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
2023-04-24 03:06:39 +02:00
Felix Baumann
45cf200b2e ramips: Cudy X6 fixes / improvements
- Correct WiFi MACs, they didn't match oem firmware
- Move nvmem-cells to bdinfo partition and remove &bdinfo reference
- Add OEM device model name R13 to SUPPORTED_DEVICES
  This allows sysupgrading from Cudy's OpenWrt fork without force
- Label red_led and use it during failsafe mode and upgrades

MAC addresses as verified by OEM firmware:

use   address             source
LAN   b4:4b:d6:2d:c8:4a   label
WAN   b4:4b:d6:2d:c8:4b   label + 1
2g    b4:4b:d6:2d:c8:4a   label
5g    b6:4b:d6:3d:c8:4a   label + LA-Bit set + 4th oktet increased

The label MAC address is found in bdinfo 0xde00.

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
[read wifi mac from flash offset]
Signed-off-by: David Bauer <mail@david-bauer.net>
2023-04-24 02:57:26 +02:00
Haoan Li
c7b484f364 ramips: fix lzma-loader for buffalo_WSR_600DHP
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.

Fixes: #11919
Signed-off-by: Haoan Li <lihaoan1001@163.com>
2023-04-23 14:12:11 +02:00
Daniel Kestrel
e1242fc339
generic: 5.15: replace ramips AR8033 fiber patch with 5.18 patches
A patch was added in kernel 5.4 to support the fiber operation of
AR8033 with ramips devices. In kernel 5.18 similar enhancements
were added to the kernel. Those patches are required for other
fiber based devices but when added, build fails for ramips targets.
This commit removes the ramips patch and adds the kernel 5.18 ones.

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
[ split commit,refresh patch and improve commit message ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-04-22 17:21:29 +02:00