Commit Graph

73 Commits

Author SHA1 Message Date
Stefan Lippers-Hollmann
d9c2b0cfdd ipq806x: ASRock g10: fix bogus read errors
Properly declare that the g10 is booting from NAND and define its
correct (larger than on other devices-) boot_pages_size, to prevent
the kernel from constantly falling over missing OOB error correction
for the bootloader.

This patch prevents a constant slew of (bogus) read errors reported
by the kernel and keeping the CPU busy and fixes:

blk_update_request: I/O error, dev mtdblock0, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
Buffer I/O error on dev mtdblock0, logical block 0, async page read
blk_update_request: I/O error, dev mtdblock0, sector 32 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 40 op 0x0:(READ) flags 0x80700 phys_seg 7 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 48 op 0x0:(READ) flags 0x80700 phys_seg 6 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 56 op 0x0:(READ) flags 0x80700 phys_seg 5 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 64 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
Buffer I/O error on dev mtdblock0, logical block 1, async page read
Buffer I/O error on dev mtdblock1, logical block 0, async page read
Buffer I/O error on dev mtdblock1, logical block 1, async page read
Buffer I/O error on dev mtdblock2, logical block 0, async page read
Buffer I/O error on dev mtdblock2, logical block 1, async page read
Buffer I/O error on dev mtdblock3, logical block 0, async page read
Buffer I/O error on dev mtdblock3, logical block 0, async page read
Buffer I/O error on dev mtdblock4, logical block 0, async page read
Buffer I/O error on dev mtdblock4, logical block 1, async page read

Suggested-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2022-01-02 20:41:50 +01:00
Matthew Hagan
67f5201276 ipq806x: add support for Cisco Meraki MR42/MR52
The MR42 and MR52 are two similar IPQ806x based devices from the Cisco
Meraki "Cryptid" series.

  MR42 main features:
  -  IPQ8068 1.4GHz
  -  512MB RAM
  -  128MB NAND
  -  2x QCA9992 (2.4 & 5GHz)
  -  1x QCA9889 (2.4 & 5GHz)
  -  1x AR8033 PHY
  -  PoE/AC power

  MR52 main features:
  -  IPQ8068 1.4GHz
  -  512MB RAM
  -  128MB NAND
  -  2x QCA9994 (2.4 & 5GHz)
  -  1x QCA9889 (2.4 & 5GHz)
  -  2x AR8033 PHYs
  -  PoE/AC power

(MR42 Only) Installation via diagnostic mode:

If you can successfully complete step 1 then you can continue to install
via this method without having to open the device. Otherwise please use
the standard UART method. Please note that when booting via TFTP, some
Ethernet devices, in particular those on laptops, will not connect in
time, resulting in TFTP boot not succeeding. In this instance it is
advised to connect via a switch.

  1. Hold down reset at power on and keep holding, after around 10 seconds
     if the orange LED changes behaviour to begin flashing, proceed to
     release reset, then press reset two times. Ensure that the LED has
     turned blue. Note that flashing will occur on some devices, but it
     will not be possible to change the LED colour using the reset button.
     In this case it will still be possible to continue with this install
     method.

  2. Set your IP to 192.168.1.250. Set up a TFTP server serving
     mr42_u-boot.mbn and
     openwrt-ipq806x-generic-meraki_mr42-initramfs-fit-uImage.itb, obtained
     from [1].

  3. Use telnet and connect to 192.168.1.1. Run the following commands to
     install u-boot. Note that all these commands are critical, an error
     will likely render the device unusable.

     Option 3.1:
       If you are sure you have set up the TFTP server correctly you can
       run this script on the device. This will download and flash the
       u-boot image immediately:

       `/etc/update_uboot.sh 192.168.1.250 mr42_u-boot.mbn`

       Once completed successfully, power off the device.

     Option 3.2:
       If you are unsure the TFTP server is correctly set up you can
       obtain the image and flash manually:

       3.2.1. `cd /tmp`
       3.2.2. `tftp-hpa 192.168.1.250 -m binary -c get mr42_u-boot.mbn`
       3.2.3. Confirm file has downloaded correctly by comparing the
              md5sum:

            `md5sum mr42_u-boot.mbn`

       3.2.4. The following are the required commands to write the image.

            `echo 1 > /sys/devices/platform/msm_nand/boot_layout
             mtd erase /dev/mtd1
             nandwrite -pam /dev/mtd1 mr42_u-boot.mbn
             echo 0 > /sys/devices/platform/msm_nand/boot_layout`

          Important: You must observe the output of the `nandwrite`
          command. Look for the following to verify writing is occurring:

            `Writing data to block 0 at offset 0x0
             Writing data to block 1 at offset 0x20000
             Writing data to block 2 at offset 0x40000`

          If you do not see this then do not power off the device. Check
          your previous commands and that mr42_u-boot.mbn was downloaded
          correctly. Once you are sure the image has been written you
          can proceed to power off the device.

  4. Hold the reset button and power on the device. This will immediately
     begin downloading the appropriate initramfs image and boot into it.

     Note: If the device does not download the initramfs, this is likely
     due to the interface not being brought up in time. Changing Ethernet
     source to a router or switch will likely resolve this. You can also
     try manually setting the link speed to 10Mb/s Half-Duplex.

  5. Once a solid white LED is displayed on the device, continue to the
     UART installation method, step 6.

Standard installation via UART - MR42 & MR52

  1. Disassemble the device and connect a UART header. The header pinout
     is as follows:

       1 - 3.3v
       2 - TXD
       3 - RXD
       4 - GND

     Important: You should only connect TXD, RXD and GND. Connecting
     3.3v may damage the device.

  2. Set your IP to 192.168.1.250. Set up a TFTP server serving
     openwrt-ipq806x-generic-meraki_(mr42|mr52)-initramfs-fit-uImage.itb.
     Separately obtain the respective sysupgrade image.

  3. Run the following commands, preferably from a Linux host. The
     mentioned files, including ubootwrite.py and u-boot images, can be
     obtained from [1].

       `python ubootwrite.py --write=(mr42|mr52)_u-boot.bin`

     The default for "--serial" option is /dev/ttyUSB0.

  4. Power on the device. The ubootwrite script will upload the image to
     the device and launch it. The second stage u-boot will in turn load
     the initramfs image by TFTP, provided the TFTP server is running
     correctly. This process will take about 13 minutes. Once a solid
     white LED is displayed, the image has successfully finished
     loading. Note: If the image does not load via TFTP, try again with
     the Ethernet link to 10Mb/s Half-Duplex.

  5. (MR42 only) Do not connect over the network. Instead connect over
     the UART using minicom or similar tool. To replace u-boot with
     the network enabled version, please run the following commands.
     Note that in the provided initramfs images, the u-boot.mbn file
     is located in /root:

     If you have not used the provided initramfs, you must ensure you
     are using an image with "boot_layout" ECC configuration enabled in
     the Kernel. This will be version 5.10 or higher. If you do not do
     this correctly the device will be bricked.

       `insmod mtd-rw i_want_a_brick=1
        mtd erase /dev/mtd8
        nandwrite -pam /dev/mtd8 /root/mr42_u-boot.mbn`

     After running nandwrite, ensure you observe the following output:

       `Writing data to block 0 at offset 0x0
        Writing data to block 1 at offset 0x20000
        Writing data to block 2 at offset 0x40000`

  6. (Optional) If you have no further use for the Meraki OS, you can
     remove all other UBI volumes on ubi0 (mtd11), including diagnostic1,
     part.old, storage and part.safe. You must not remove the ubi1 ART
     partition (mtd12).

       `for i in diagnostic1 part.old storage part.safe ; do
        ubirmvol /dev/ubi0 -N $i
        done`

  7. Proceed to flash the sysupgrade image via luci, or else download or
     scp the image to /tmp and use the sysupgrade command.

[1] The mentioned images and ubootwrite.py script can be found in this repo:
    https://github.com/clayface/openwrt-cryptid

[2] The modified u-boot sources for the MR42 and MR52 are available:
    https://github.com/clayface/U-boot-MR52-20200629

Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-11-28 17:51:52 +01:00
Robert Marko
76fff69180 ipq806x: ecw5410: use bootloader provided MAC-s
Currently, we are overriding the bootloader provided MAC-s as the ethernet
aliases are reversed so MAC-s were fixed up in userspace.
There is no need to do that as we can just fix the aliases instead and get
rid of MAC setting via userspace helper.

Fixes: 59f0a0f ("ipq806x: add Edgecore ECW5410 support")

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-10-31 21:24:47 +01:00
Robert Marko
fa3646c003 ipq806x: ecw5410: drop GPIO based MDIO1 node
It looks like this is a leftover before there was a proper MDIO driver.
Since both PHY-s are connected to the HW MDIO bus there is no reason for
this to exist anymore, especially since it uses the same pins as the HW
controller and has the pinmux for the set to "MDIO" so this worked by
pure luck as GPIO MDIO would probe first and override the HW driver.

Move the GMAC3 to simply use the same MDIO bus phandle.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-10-31 21:24:47 +01:00
Ansuel Smith
f44e933458 ipq806x: provide WiFI mac-addresses from dts
Use nvmem framework for supported mac-address stored
in nvmem cells and drop mac patch function for hotplug
script for supported devices.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[rebase, move to correct node for d7800, include xr500]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-30 22:11:13 +02:00
Peter Geis
70c12d26ca ipq806x: add support for Netgear Nighthawk Pro Gaming XR500
This adds support for the Netgear Nighthawk Pro Gaming XR500.
It is the successor to the Netgear Nighthawk R7800 and shares almost
identical hardware to that device.
The stock firmware is a heavily modified version of OpenWRT.

Specifications:
  SoC: Qualcomm Atheros IPQ8065
  RAM: 512 MB
  Storage: 256 MiB NAND Flash
  Wireless: 2x Qualcomm Atheros QCA9984
  Ethernet: 2x 1000/100/10 dedicated interfaces
  Switch: 5x 1000/100/10 external ports
  USB: 2x 3.0 ports

More information:
Manufacturer page: https://www.netgear.com/gaming/xr500/
Almost identical to Netgear R7800
Differences (r7800 > xr500):
  Flash: 128MiB > 256MiB
  Removed esata
  swapped leds:
    usb1 (gpio 7 > 8)
    usb2 (gpio 8 > 26)
    guest/esata (gpio 26 > 7)

MAC addresses:

On the OEM firmware, the mac addresses are:

  WAN: *:50  art 0x6
  LAN: *:4f  art 0x0 (label)
  2G:  *:4f  art 0x0
  5G:  *:51  art 0xc

Installation:
Install via Web Interface (preferred):
Utilize openwrt-ipq806x-netgear_xr500-squashfs-factory.img

Install via TFTP recovery:
1.Turn off the power, push and hold the reset button (in a hole on
  backside) with a pin
2.Turn on the power and wait till power led starts flashing white
  (after it first flashes orange for a while)
3.Release the reset button and tftp the factory img in binary mode.
  The power led will stop flashing if you succeeded in transferring
  the image, and the router reboots rather quickly with the new
  firmware.
4.Try to ping the router (ping 192.168.1.1). If does not respond,
  then tftp will not work either.

Uploading the firmware image with a TFTP client
$ tftp 192.168.1.1
bin
put openwrt-ipq806x-netgear_xr500-squashfs-factory.img

Note:

The end of the last partition is at 0xee00000. This was chosen
by the initial author, but nobody was able to tell why this
particular arbitrary size was chosen. Since it's not leaving
too much empty space and it's the only issue left, let's just
keep it for now.

Based on work by Adam Hnat <adamhnat@gmail.com>
ref: https://github.com/openwrt/openwrt/pull/3215

Signed-off-by: Peter Geis <pgwipeout@gmail.com>
[squash commits, move common LEDs to DTSI, remove SPDX on old
 files, minor whitespace cleanup, commit message facelift,
 add MAC address overview, add Notes, fix MAC addresses,
 use generic name for partition nodes in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-26 22:30:18 +02:00
Filip Matijević
e2b03c16eb ipq806x: add missing enclosing partitions block for TP-Link C2600
The partitions that have compatible property set are skipped by mtd if
they are not contained inside a partitions node and this breaks
fetching MAC address from "default-mac" partition.

Fix this by defining all the partitions inside partitions node with
compatible = "fixed-partitions" as nvmem requires the standard
partitions scheme to work correctly.

Fixes: FS#3945
Fixes: cd36d71655 ("ipq806x/dts: Add Archer C2600 DTS")
Fixes: 0458a8993c ("ipq806x: convert mtd-mac-address to nvmem
implementation")

Signed-off-by: Filip Matijević <filip.matijevic.pz@gmail.com>
Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
[adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-30 00:37:35 +02:00
Chukun Pan
269758a5bc ipq806x: Askey RT4230W REV6: use usual writing for pcie part
The problem has been fixed in f47cb405ca ("ipq806x: fix pci broken
on bootm command"), now the pcie part can be written in the usual way.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-08-25 01:42:16 +02:00
Shane Synan
9baca41064 ipq806x: fix min<>target opp-microvolt DTS mixup
Rearrange all voltage triplets for "opp_table0" to match the
specifications.  "opp-microvolt" and "opp-microvolt-<name>" triplets
are in order of <target min max>, and NOT <min target max>.

Previously, the CPU would *always* spend its time at the "minimum"
voltage, ignoring the actual intended target.  This is a regression
from previous behavior.

On an NBG6817 with a Qualcomm CPU of PVS bin #2...
(see &opp_table0 -> opp-1725000000 -> opp-microvolt-speed0-pvs2-v0)

* Before:
/usr/bin/tail -n +1 /sys/kernel/debug/opp/cpu0/opp\:1725000000/supply-0/u_volt_*
==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_max <==
1260000

==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_min <==
1200000

==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_target <==
1140000

* After:
/usr/bin/tail -n +1 /sys/kernel/debug/opp/cpu0/opp\:1725000000/supply-0/u_volt_*
==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_max <==
1260000

==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_min <==
1140000

==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_target <==
1200000

To check voltages and frequencies at run time, use...
/bin/cat /sys/kernel/debug/regulator/regulator_summary &&
  /bin/cat /sys/kernel/debug/clk/clk_summary | grep "hfpll"

See
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/tree/Documentation/devicetree/bindings/opp/opp.txt?h=v5.4.142#n91

Fixes: 1e25423be8 ("ipq806x: refresh dtsi patches")

Signed-off-by: Shane Synan <digitalcircuit36939@gmail.com>
Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
[commit message style cleanup, another kernel refresh]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-21 23:54:31 +02:00
Ansuel Smith
0458a8993c ipq806x: convert mtd-mac-address to nvmem implementation
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-07-19 14:51:22 +02:00
Ansuel Smith
d284e6ef0f treewide: convert mtd-mac-address-increment* to generic implementation
Rework patch 681-NET-add-mtd-mac-address-support to implement
only the function to read the mac-address from mtd.
Generalize mtd-mac-address-increment function so it can be applied
to any source of of_get_mac_address.
Rename any mtd-mac-address-increment to mac-address-increment.
Rename any mtd-mac-address-increment-byte to mac-address-increment-byte.

This should make simplify the conversion of target to nvmem implementation.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-07-19 14:51:22 +02:00
Ansuel Smith
014aac7944 ipq806x: fix missing 1.4ghz cache freq for ipq8065 SoC
With the new implementation of the dedicated cpufreq driver,
the 1.4 Ghz was only dropped and not added to the ipq8065 SoC.
Fix this to improve performance.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-06-30 23:14:43 +02:00
Lauro Moreno
da8428d277 ipq806x: add support for Askey RT4230W REV6
This adds support for the Askey RT4230W REV6
(Branded by Spectrum/Charter as RAC2V1K)

At this time, there's no way to reinstall the stock firmware so don't install
this on a router that's being rented.

Specifications:

    Qualcomm IPQ8065
    1 GB of RAM (DDR3)
    512 MB Flash (NAND)
    2x Wave 2 WiFi cards (QCA9984)
    5x 10/100/1000 Mbps Ethernet (Switch: QCA8337)
    1x LED (Controlled by a microcontroller that switches it between red and
        blue with different patterns)
    1x USB 3.0 Type-A
    12V DC Power Input
    UART header on PCB - pinout from top to bottom is RX, TX, GND, 5V
    Port settings are 115200n8

More information: https://forum.openwrt.org/t/askey-rac2v1k-support/15830
https://deviwiki.com/wiki/Askey_RAC2V1K

To check what revision your router is, restore one of these config backups
through the stock firmware to get ssh access then run
"cat /proc/device-tree/model".
https://forum.openwrt.org/t/askey-rac2v1k-support/15830/17
The revision number on the board doesn't seem to be very consistent so that's
why this is needed. You can also run printenv in the uboot console and if
machid is set to 177d, that means your router is rev6.

Note: Don't install this if the router is being rented from an ISP. The defined
partition layout is different from the OEM one and even if you changed the
layout to match, backing up and restoring the OEM firmware breaks /overlay so
nothing will save and the router will likely enter a bootloop.

How to install:

Method 1: Install without opening the case using SSH and tftp

    You'll need:
    RAC2V1K-SSH.zip:
https://github.com/lmore377/openwrt-rt4230w/blob/master/RAC2V1K-SSH.zip
    initramfs and sysupgrade images

    Connect to one of the router's LAN ports

    Download the RAC2V1K-SSH.zip file and restore the config file that
corresponds to your router's firmware (If you're firmware is newer than what's
in the zip file, just restore the 1.1.16 file)

    After a reboot, you should be able to ssh into the router with username:
"4230w" and password: "linuxbox" or "admin". Run the following commannds
     fw_setenv ipaddr 10.42.0.10 #IP of router, can be anything as long as
it's in the same subnet as the server
     fw_setenv serverip 10.42.0.1# #IP of tftp server that's set up in next
steps
     fw_setenv bootdelay 8
     fw_setenv bootcmd "tftpboot initramfs.bin; bootm; bootipq"

    Don't reboot the router yet.

    Install and set up a tftp server on your computer

    Set a static ip on the ethernet interface of your computer (use this for
serverip in the above commands)

    Rename the initramfs image to initramfs.bin, and host it with the tftp
server

    Reboot the router. If you set up everything right, the router led should
switch over to a slow blue glow which means openwrt is booted. If for some
reason the file doesn't get loaded into ram properly, it should still boot to
the OEM firmware.
    After openwrt boots, ssh into it and run these commands:
    fw_setenv bootcmd "setenv mtdids nand0=nand0 && setenv mtdparts
 mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi
read 0x44000000 kernel 0x6e0000 && bootm"
    fw_setenv bootdelay 2

    After openwrt boots up, figure out a way to get the sysupgrade file onto it
(scp, custom build with usb kernel module included, wget, etc.) then flash it
with sysupgrade. After it finishes flashing, it should reboot, the light should
start flashing blue, then when the light starts "breathing" blue that means
openwrt is booted.

Method 2: Install with serial access (Do this if something fails and you can't
boot after using method 1)

    You'll need:
    initramfs and sysupgrade images
    Serial access:
https://openwrt.org/inbox/toh/askey/askey_rt4230w_rev6#opening_the_case

    Install and set up a tftp server

    Set a static ip on the ethernet interface of your computer

    Download the initramfs image, rename it to initramfs.bin, and host it with
the tftp server

    Connect the wan port of the router to your computer

    Interrupt U-Boot and run these commands:
    setenv serverip 10.42.0.1 (You can use whatever ip you set for the computer)
    setenv ipaddr 10.42.0.10 (Can be any ip as long as it's in the same subnet)
    setenv bootcmd "setenv mtdids nand0=nand0 &&
set mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware
&& ubi read 0x44000000 kernel 0x6e0000 && bootm"

    saveenv
    tftpboot initramfs.bin
    bootm

    After openwrt boots up, figure out a way to get the sysupgrade file onto it
(scp, custom build with usb kernel module included, wget, etc.) then flash it
with sysupgrade. After it finishes flashing, it should reboot, the light should
start flashing blue, then when the light starts "breathing" blue that means
openwrt is booted.

Signed-off-by: Lauro Moreno <lmore377@gmail.com>
[add entry in 5.10 patch, fix whitespace issues]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-05 23:39:14 +02:00
Ansuel Smith
3bae740311 ipq806x: add missing wakeup-source for gpio keys
wakeup-source is required for gpio keys to fix error
genirq: irq_chip msmgpio did not update eff. affinity mask

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-05-07 07:05:16 +02:00
Ansuel Smith
1603d09964 ipq806x: apply correct voltage tolerance
Voltage tolerance was 5%, not 5000. Update min and max voltage of the target opp.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-05-07 07:05:16 +02:00
Ansuel Smith
d079c8fa48 ipq806x: simplify ecw5410 dts
Simplify ecw5410 dts instead of redefine nodes.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-05-07 07:05:16 +02:00
Ansuel Smith
e3daef34a0 ipq806x: set boot layout for nandc compatible
Set boot layout size to fix io error on block scan.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-05-07 07:05:16 +02:00
Ansuel Smith
1e25423be8 ipq806x: refresh dtsi patches
- Add new tsens node
- Add new cpufreq required nodes
- Drop arm cpuidle compatible
- Fix duplicate node set upstream
- Add voltage tolerance value for cpu opp

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-05-07 07:05:16 +02:00
Ansuel Smith
c864f587a2 ipq806x: backport mtd adm and smem driver
- Backport mtd adm driver from kernel 5.12
- Backport mtd parser smem from kernel 5.11
- Fix mtd rootfs patch
- Update qcom,smem compatible to qcom,smem-parts

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-05-07 07:05:16 +02:00
Mark Mentovai
565814a5ee ipq806x: ubnt,unifi-ac-hd: reorder eth0 and eth1
The Ubiquiti UniFi AC HD (UAP-AC-HD, UAP301) has two Ethernet ports,
labeled MAIN and SECONDARY, connected to gmac2 and gmac1, respectively.
The standard probe order results in gmac1/SECONDARY being eth0 and
gmac2/MAIN being eth1. This does not match the stock firmware, is
contrary to user expectation, causes the wrong (high) MAC address to be
used in a bridged configuration (the default for this device), and makes
the gmac2/MAIN port unusable in the preinit environment (such as for
failsafe). Until a recent patch, gmac1/SECONDARY (eth0) was not even
usable.

This reorders the ports so that gmac2/MAIN is eth0, and the now-working
gmac1/SECONDARY is eth1. eth0 has the low MAC address and eth1 has the
high; when bridged, the bridge takes on the correct low MAC address.
This matches the stock firmware. The MAIN port is usable for failsafe
during preinit.

This device does not have a switch on board, so there's no possibility
to remap ports via switch configuration. "ip link set $interface name"
is used instead, during preinit before networking is configured.

Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
2021-05-07 07:05:16 +02:00
Mark Mentovai
4f74966852 ipq806x: ubnt,unifi-ac-hd: use on-board PHYs
Unlike many ipq806x devices, Ubiquiti UniFi AC HD (UAP-AC-HD, UAP301)
has no switch on board. Its two Ethernet ports are connected to Atheros
AR8033 PHYs. It is not appropriate to use fixed-link in this
configuration. Instead, configure the correct PHYs in the device tree
configuration to allow the at803x driver to load.

Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
2021-05-07 07:05:16 +02:00
Daniel Golle
d0d63162b6
ipq806x: work-around vendor 'rootfs_data' GPT partition
ZyXEL NBG6817 comes with an eMMC which contains a GPT partition named
'rootfs_data'. This currently confuses fstools and makes it pick that
(not suitable) partition.
Use the newly introduced fstools_ignore_partname=1 kernel cmdline
parameter to have fstools ignore that partition.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-19 13:36:02 +00:00
Adrian Schmutzler
04a0e5c082 ipq806x: replace full-text BSC license by SPDX identifier
This replaces a full-text BSD clause by the corresponding SPDX
identifier.

This should make it easier to identify the license both by humans
and machines.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 18:28:30 +01:00
Jan Alexander
05707e6460 ipq806x: fix Ubiquiti UniFi AC HD partition map
This fixes a typo in the previously committed partition map that led to
the extension of the read-only mtd partition "SSD" into the following
partitions.

Fixes: 4e46beb313 ("ipq806x: add support for Ubiquiti UniFi AC HD")

Signed-off-by: Jan Alexander <jan@nalx.net>
2021-01-15 17:34:04 +01:00
Jan Alexander
4e46beb313 ipq806x: add support for Ubiquiti UniFi AC HD
Hardware
--------

SoC:   Qualcomm IPQ8064
RAM:   512MB DDR3
Flash: 256MB NAND (Micron MT29F2G08ABBEAH4)
       32MB SPI-NOR (Macronix MX25U25635F)
WLAN:  Qualcomm Atheros QCA9994 4T4R b/g/n
       Qualcomm Atheros QCA9994 4T4R a/n/ac
ETH:   eth0 - SECONDARY (Atheros AR8033)
       eth1 - MAIN (Atheros AR8033)
USB:   USB-C
LED:   Dome (white / blue)
BTN:   Reset

Installation
------------

Copy the OpenWrt sysupgrade image to the /tmp directory of the device
using scp. Default IP address is 192.168.1.20 and default username and
password are "ubnt".

SSH to the device and write the bootselect flag to ensure it is booting
from the mtd partition the OpenWrt image will be written to. Verify the
output device below matches mtd partition "bootselect" using /proc/mtd.

> dd if=/dev/zero bs=1 count=1 seek=7 conv=notrunc of=/dev/mtd11

Write the OpenWrt sysupgrade image to the mtd partition labeled
"kernel0". Also verify the used partition device using /proc/mtd.

> dd if=/tmp/sysupgrade.bin of=/dev/mtdblock12

Reboot the device.

Back to stock
-------------

Use the TFTP recovery procedure with the Ubiquiti firmware image to
restore the vendor firmware.

Signed-off-by: Jan Alexander <jan@nalx.net>
2021-01-14 01:03:54 +01:00
Adrian Schmutzler
849d4b3940 ipq806x: add space before SPDX identifier (again)
Strictly, an SPDX identifier requires a space between the comment
marker and the identifier itself. This has been addressed in
b69c21738e ("treewide: add space before SPDX identifier"), but
some new malformatted identifiers were merged recently.

This could have been prevented by using checkpatch.pl earlier.

Fixes: 1a775a4fd0 ("ipq806x: add support for TP-Link Talon AD7200")
Fixes: 8ddaeaf642 ("ipq806x: create DTSI for TP-Link AD7200 and C2600")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-06 23:53:25 +01:00
Adrian Schmutzler
8ddaeaf642 ipq806x: create DTSI for TP-Link AD7200 and C2600
Both devices share most of their setup except buttons and LEDs,
so having a common DTSI removes a lot of duplicate code.

In order to have a shared partitioning scheme, device-id and
product-info from AD7200 have been merged into a single
product-info partition like for C2600.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-06 14:43:12 +01:00
Adrian Schmutzler
8050b70514 ipq806x: clean up DTS file for TP-Link AD7200
This does several cosmetic adjustments for AD7200's DTS:

 - Make node name, DT label and label property consistent
 - Drop wrong and unused spi4 label
 - Use generic flash@0 node name

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-06 14:43:12 +01:00
Daniel Golle
28fd279e5d ipq806x: some corrections for TP-Link Talon AD7200
Address most comments made by Adrian Schmutzler on the mailing list.
The device name is kept as 'TP-Link Talon AD7200' as that seems to be
the marketing name TP-Link chose for that device, it also matches the
naming scheme for other TP-Link devices (e.g. 'TP-Link Archer C7').

Fixes: 1a775a4fd0 ("ipq806x: add support for TP-Link Talon AD7200")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-01-05 12:58:43 +00:00
Gary Cooper
1a775a4fd0 ipq806x: add support for TP-Link Talon AD7200
Device hardware: https://deviwiki.com/wiki/TP-LINK_AD7200_(Talon)

The Talon AD7200 is basically an Archer C2600 with a third PCIe lane
and an 802.11ad radio. It looks like the Archers C2600/5400 but the
housing is slightly larger.

Specifications
--------------

  - IPQ8064 dual-core 1400MHz
  - QCA9988 2.4GHz WiFi
  - QCA9990 5GHz WiFi
  - QCA9500 60GHz WiFi
  - 32MB SPI Flash
  - 512MiB RAM
  - 5 GBit Ports (QCA8337)

Installation
------------

Installation is possible from the OEM web interface.
Sysupgrade is possible.
TFTP recovery is possible.
  - Image: AD7200_1.0_tp_recovery.bin

Notes
  - This will be the first 802.11ad device supported by mainline.

Signed-off-by: Gary Cooper <gaco@bitmessage.de>
2021-01-05 02:16:24 +00:00
Sungbo Eo
cbccc2560c ipq806x: consolidate DTS files directory
Commit 29ca10e537 ("ipq806x: remove support for kernel 4.19") moved
DTS files to "files" directory, but after that a new DTS file was added
to the former "files-5.4" directory. Move it to the new directory.

Fixes: 98b86296e6 ("ipq806x: add support for ASRock G10")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-01-03 15:50:55 +01:00
Yanase Yuki
3bb1618573 ipq806x: add support for NEC Platforms Aterm WG2600HP3
NEC Platforms Aterm WG2600HP3 is a dual-band router based on Qualcomm IPQ8062.

Specification
-------------
- SoC: Qualcomm IPQ8062
- RAM: 512MiB
- Flash memory: SPI-NOR 32MiB (Cypress S25FL256S)
- Wi-Fi: Qualcomm QCA9984 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm QCA9984 (5GHz, 36ch - 64ch, 100ch - 140ch)
- Ethernet: 4x 100/1000 Mbps (1x WAN, 4x LAN)
- LED: 6x green LED, 6x red LED
- Input: 2x tactile switch, 1x SP3T slide switch
- Serial console: 115200bps, through-hole J3
  - [  ] [GND] [  ] [TX] [RX] ----> DC jack
- Power: DC 12V 1.5A

This device does not support VHT160 and VHT80+80.
Custom BDFs are required to limit VHT capabilities.

Flash instructions
------------------
1. Setup TFTP server (IP address: 192.168.1.2)
2. Put initramfs image into TFTP server directory
3. Connect WG2600HP3 lan port and computer that runs TFTP server
4. Connect to the serial console
5. Interrupt booting by Esc key (password: chiron)
6. Execute the following commands
    # setenv bootcmd "nboot 0x44000000 1 0x860000"
    # saveenv
    # setenv ipaddr 192.168.1.1
    # setenv serverip 192.168.1.2
    # tftpboot 0x44000000 openwrt-ipq806x-generic-nec_wg2600hp3-initramfs-uImage
7. After booting OpenWrt initramfs image, backup SPI-NOR flash memory
8. Erase firmware partition
    # mtd erase firmware
9. Run sysupgrade

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
2020-12-25 10:38:13 +01:00
Yanase Yuki
d64102e00a ipq806x: add support for Qualcomm IPQ8062 SoC
This commit adds support for Qualcomm IPQ8062 SoC.
IPQ8062 is a lower clock variant of IPQ8064.

CPU and NSS clocks:
- CPU: 384 MHz - 1 GHz
- NSS: 110 MHz - 550 MHz

opp and l2 clock values are taken from WG2600HP3 GPL source code [1].

Due to a lack of devices, I didn't test the following features.
- SATA
- NAND flash memory controller
- SD
- USB
- GSBI2, GSBI7
- PCIE2
- GMAC0, GMAC3

Works properly:
- GSBI4 UART
- GSBI5 SPI
- GMAC1, GMAC2
- PCIE0, PCIE1
- MDIO0

Does not work properly:
- CPU SPC
  - This can cause a system hang. Same as IPQ8065.
    See 2336c2dbb1

[1] https://www.aterm.jp/function/wg2600hp3/appendix/opensource.html

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
2020-12-25 10:38:13 +01:00
INAGAKI Hiroshi
622ce713ca ipq806x: disable SPC of IPQ8064 on NEC WG2600HP to fix boot issue
The SPC (Standalone Power Collapse) of IPQ8064 on NEC Aterm WG2600HP
need to be disabled to fix the boot stucking issue on WG2600HP with
kernel 5.4.

log:

[    3.036965] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[    3.038007] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[    3.045849] sdhci: Secure Digital Host Controller Interface driver
[    3.052385] sdhci: Copyright(c) Pierre Ossman
[    3.058712] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.065469] NET: Registered protocol family 10
[    3.070184] Segment Routing with IPv6
[    3.073141] NET: Registered protocol family 17
[    3.078157] 8021q: 802.1Q VLAN Support v1.8
[    3.081149] Registering SWP/SWPB emulation handler
[    3.107125] qcom_rpm 108000.rpm: RPM firmware 3.0.16777371
[    3.120475] s1a: Bringing 0uV into 1050000-1050000uV
[    3.120747] s1a: supplied by regulator-dummy
[    3.124775] s1b: Bringing 0uV into 1050000-1050000uV
[    3.128969] s1b: supplied by regulator-dummy
[    3.133905] s2a: Bringing 0uV into 800000-800000uV
[    3.138190] s2a: supplied by regulator-dummy
[    3.142693] s2b: Bringing 0uV into 800000-800000uV
[    3.147266] s2b: supplied by regulator-dummy
[
(stuck)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-12-22 19:11:50 +01:00
Peter Cardoe
b163bfbba5 ipq806x: Fix gmac1 (WAN) on Netgear D7800
The WAN port on Netgear D7800 is unable to connect to an ISP when the
link to the modem is running at less than 1GB.

This patch fixes the issue by removing the phy-handle definition
and replacing it with a fixed-link definition

The WAN port is then able to connect to a modem via a link running at 100Mbs or 10Mbs

Fixes: FS#3086
Signed-off-by: Peter Cardoe <peter@cardoe.co.uk>
2020-12-22 18:59:10 +01:00
Adrian Schmutzler
29ca10e537 ipq806x: remove support for kernel 4.19
The target uses 5.4 as default kernel since 04/2020.

Kernel 4.19 support is not really maintained anymore, and there has
been a lot of changes between 4.19 and 5.4 on this target. Despite,
new devices are typically added for 5.4 only anyway.

Thus, make maintaining of old stuff and reviewing of new stuff
easier by removing support for kernel 4.19.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-19 15:37:54 +02:00
John Crispin
bb255f7429 ipq806x: add v4.9 support
Signed-off-by: John Crispin <john@phrozen.org>
2017-02-16 20:25:32 +01:00
André Valentin
8725d1cffa ipq806x: fixup nbg6817 internal mmc and switch configuration in DTS
The setting mmc-ddr-1_8v in the platform dts leads to read errors. The
device is unusable and system reboots in a loop. Because NBG6817 is the
only mmc device, I removed it in base dts.

The second change removes settings now present in base dts.

The third change references was a wrong conversion of constants in the switch settings.
Switch now initializes again.

Signed-off-by: André Valentin <avalentin@marcant.net>
2017-02-02 22:48:33 +01:00
Pavel Kubelun
8004aa313a ipq806x: refactor ipq8065 device tree
At the moment we have 2 seperate device tree sources: 1 for ipq8064 soc located
in kernel source and 1 custom in LEDE for ipq8065.
ipq8064 and ipq8065 SoCs are completely identical except ipq8065 has higher cpu
frequencies and adjusted corresponding power supply.

This commit makes ipq8065 DTS to contain only specific for ipq8065 DT entries while
pulling all the basic SoC stuff from ipq8064 DTS.

It makes easier to manage ipq806x device trees and instead of committing changes into
2 seperate equal DTS we are ending up with only 1.
It also enables ipq8065 devices to automatically receive changes made in upstream kernel.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-01-15 20:56:30 +01:00
Pavel Kubelun
44b44595dc ipq806x: update eMMC and SDCC3 nodes in device tree
Enable bam dma support for eMMC and SDCC3 in device tree and update nodes
to reflect Qualcomm SDK.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-01-15 20:56:30 +01:00
Pavel Kubelun
45bf3d4f24 ipq806x: disable usb3 phy suspend and add usb tcsr control
According to Qualcomm SDK usb3 phy suspend should be disabled for
ipq806x.
This may solve issue on some ipq806x devices that breaks usb3
storage peripherals during system boot.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-01-15 20:56:30 +01:00
Pavel Kubelun
6ebb46a40a ipq806x: fix pvs1_bin voltage in ipq8065 DT
Fixing pvs1 bin voltage as found in GPL tarball and Qualcomm SDK.

Also adjusting smb208_s2a/b minimum voltage to reflect lowest value in pvs table.

Current ipq8065 devices in LEDE choose (based on eFuse data) pvs bin n4, that has
correct values in DT, but in future a new device may choose n1 or n6.

Without this change n1 is semi-correct and n6 is not available, because OPP driver
disregards bins with voltage values that regulator cannot supply.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-01-10 08:11:14 +01:00
dissent1
fef6a96d9e ipq806x: add thermal sensor driver
Allows to check cpu temperature.

Huge thanks to @hnyman for valuable assistance!

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-12-01 15:47:43 +01:00
Mathias Kresin
3228c2a682 ipq806x: more dts cleanup
Remove the wifi5g LED from the the d7800, r7500 and r7800. Albeit this
GPIO is mentioned in the GPL tarball, it doesn't do anything. The
2.4/5 GHz LEDs are connected to the wifi chips and not be controlled
from the the userspace.

Use the LEDs names/colours as they are used in the board manuals. Merge
redundant LED configurations. Use the phy[0|1]tpt trigger for the
wireless LEDs. Remove the workarounds for the not controllable wireless
LEDs.

Fix spi compatible strings and remove superfluous spi-max-frequency
parameters.

If there are two power leds, use one for indicating normal operation and
one for failsafe/upgrade. Keep the on/off state of the main power led
during boot.

Use the usb pinmux settings from the nbg6817 gpl sources.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-27 15:33:54 +01:00
Henryk Heisig
e3caadc69d ipq806x: clean up dts files
Set the pinmux to the values found in the GPL tarballs of the boards.
Remove pinmux which are is not used (like nand pinmux for spi
flash boards).

This allows to use the wan orange led of the C2600 which had a wrong
pinmux before. Might fix buttons or leds of other boards as well.

Fix the LED color and the ledswitch key code of the C2600. Rename the
ledgnr to ledswitch.

Add support for indication the boot state using LEDs to the D7800,
NBG6817, R7500 and R7500v2.

Change GPIO active to readable values in D7800, EA8500, R7500,
R7500v2 and R7800.

Change gpioexport to gpio pinmux.

Add proper "drive strenght" to i2c4_pins and use it for RPM on
C2600, D7800, EA8500, R7500, R7500v2.

Remove pcie pinmux from D7800.

Move pinctrl to correct place in NBG6817 and R7800.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-27 15:24:59 +01:00
Sebastian Quilitz
ae79c41286 ipq806x: add support for TP-Link Archer VR2600v
This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.

It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.

To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.

Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
2016-11-24 22:37:40 +01:00
Pavel Kubelun
70434c3f94 ipq806x: switch to upstream usb driver and backport fixes
Also removing fifo-resize property drom DT as it has been removed from the driver.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-21 09:58:42 +01:00
Pavel Kubelun
5aace5a5fb ipq806x: fixes for R7800 and C2600
Updating spi pins configuration in R7800 and C2600 DTs
Adding more usb power pin export and gsbi6 in R7800 DT
Updating and fixing leds

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-16 10:59:30 +01:00
Pavel Kubelun
3ac5eb9141 ipq806x: fix Netgear R7500v2 memory
Netgear R7500v2 has 512MB of RAM with 2MB reserved block in the end of memory region.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-16 10:59:30 +01:00
Pavel Kubelun
bb8f5162fd ipq806x: fix pci pins
Fix pci pins drive-strength according to oem sources.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-16 10:59:30 +01:00