Commit Graph

166 Commits

Author SHA1 Message Date
Mathias Kresin
254bf7961e lantiq: xrx200: use vlan for ethernet wan port
Using the lantiq,wan device tree property for one interface node and
the lantiq,switch device tree property for another interface node at
the same time was never intended/isn't supported at the moment.

The property is meant to be used in two phy operation mode where one
phy is assigned to an interface without lantiq,* device tree property
and the other phy is assigned to an interface with the lantiq,wan
device property to have two netdevs.

If both properties are used at the same time, the lantiq,wan interface
is shown as independent netdev but not able to operate independent. The
port needs to be managed via swconfig. These dependency is not obvious
and fooled already a lot of users.

Add a default WAN vlan for xrx200 devices having an ethernet WAN port
and remove the lantiq,wan device tree property. Leave it up to the user
to set the ethernet WAN port as default WAN interface or to use this
port as additional LAN port.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-03 16:09:33 +02:00
Mathias Kresin
d49920e450 lantiq: fix avm fritz box mac addresses
It has been shown that the Fritz boxes have the correct mac address set
in the wireless calibration data/eeeprom. Use this mac address as base
for the ethernet and xdsl interface increment/decrement the address to
match the values stored in the tffs.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-05 19:59:18 +02:00
Mathias Kresin
0a26490fe4 lantiq: set the internet led interface according to wan interface
Use the nas0 interface for the netdev trigger as default. Use the ptm0
interface for xRX200 boards to match the default wan interface set in
02_network.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-18 16:52:05 +01:00
Mathias Kresin
6a6e3a4928 lantiq: introduce lantiq_is_vdsl_system
Move the code to check if the current system is a system with vdsl
support to a dedicate function to make it reusable.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-18 16:52:05 +01:00
Mathias Kresin
c5879b0676 lantiq: fix ARV7519RW22 switch port indexing
Fixes FS#454.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-18 16:52:05 +01:00
Martin Blumenstingl
32c9d467e3 lantiq: fix patching the wifi mac address on BTHOMEHUBV3A
The firmware hotplug script tries to read the mac address from a
partition with the name "uboot-env" which does not exist (instead it's
name is uboot_env). This broke calculation of the new checksum (after
patching the mac address) which resulted in ath9k refusing to use the
EEPROM data.

The original error reported by ath9k was:
PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
ath: phy0: Bad EEPROM checksum 0x2523
ath: phy0: Unable to initialize hardware; initialization status: -22
ath9k 0000:00:0e.0: Failed to initialize device

Fixes: a20616863d ("lantiq: use ath9k device tree bindings
binding/owl-loader")

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2017-02-13 07:57:04 +01:00
Mathias Kresin
ee5a6c1041 lantiq: simplify ath9k eeprom extraction script
Add an extra function to patch the mac and fixup the checksum
afterwards. Calculate the checksum position automatically. The offset
to the mac address is the same for all checksum protected EEPROMs.

No EEPROM requires a byte swapped mac address. The mac byte swap code
was required due to an bug in the script that is now fixed.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-08 19:36:53 +01:00
Martin Blumenstingl
afa3709266 lantiq: fix ath9k EEPROM data swapping for some devices
The EEPROM data in the flash of the ARV7518PW, ARV8539PW22,
BTHOMEHUBV2B and BTHOMEHUBV3A is stored byte-swapped (swab16), meaning
that for example the ath9k base_eep_header fields "version" (high and
low byte), "opCapFlags" and "eepMisc" are swapped (the latter ones are
just 1 byte wide, thus their position is swapped).

The old "ath,eep-endian" property enabled the corresponding swapping
logic in the ath9k driver (swab16 in ath9k_hw_nvram_swap_data, which is
based on the magic bytes in the EEPROM data which have nothing to do
with the calibration data - thus this logic should not be used
anymore).
Since we have switched to the upstream ath9k devicetree bindings there
is no binding anymore which enables swab16 in ath9k (as this logic is
not recommended anymore as explained above), leading to ath9k
initialization errors:
ath: phy0: Bad EEPROM VER 0x0001 or REV 0x00e0
(this shows that the version field is swapped, expected values are VER
0x000E and REV 0x0001)

Swapping the ath9k calibration data when extracting it from the flash
fixes the devices listed above (all other devices do not require
additional swapping, since the position of the fields is already as
expected by ath9k). This allows ath9k to read the version correctly
again, as well as the more important "eepmisc" field (which is used for
determining whether the data inside the EEPROM is Big or Little Endian
which is required to parse the EEPROM contents correctly).

Fixes: a20616863d ("lantiq: use ath9k device tree bindings
binding/owl-loader")

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2016-12-08 19:36:22 +01:00
Mathias Kresin
d9d838bc97 lantiq: fix image validation errors
The boards did not have the name set that is expected during metadata
validation on sysupgrade.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-04 07:03:17 +01:00
Mathias Kresin
0e34459e6b lantiq: use BT HomeHub 5 Type A OEM partition layout
This way the on nand bad block table is preserved and used. Add support
for nand OOB ECC checksums as well. It should fix all reported ubi
errors, which were all related to bad nand blocks and a purged on nand
bad block table.

The existing ubi partition will be reused, which eliminates the need
to touch the caldata during initial install. The BT u-boot has support
for loading a kernel from an ubi volume. It isn't necessary any longer
to replace the BT u-boot with a custom compiled one to use LEDE.

It is required to restore the BT Firmware and install LEDE from scratch
to switch to the new partition layout.

An image for restoring the BT firmware and installing LEDE is provided
at https://github.com/mkresin/lede/releases.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-29 21:40:16 +01:00
Martin Blumenstingl
a20616863d lantiq: use ath9k device tree bindings binding/owl-loader
This moves the extraction of the eeprom/calibration data to a hotplug
firmware script. Additionally it modifies all .dts to configure ath9k
directly from within the .dts.

The owl-loader approach enables support on devices with exotic eeprom
data locations (such as unaligned positions on the flash or data
inside an UBI volume).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[add ath9k caldata mac address patcher]
[fixes DGN3500 wifi mac]
[fixes BTHOMEHUBV3A wifi mac]
[set invalid mac for BTHOMEHUB2B, FRITZ3370, FRITZ7320 & FRITZ7360SL to restore previous random mac behavior]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-29 21:40:16 +01:00
Felix Fietkau
16adf49620 lantiq: remove device specific sysupgrade image checks
Replaced by image metadata

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-20 20:08:48 +01:00
Felix Fietkau
be296745f8 lantiq: append metadata to images
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-19 11:24:10 +01:00
Felix Fietkau
ecab500232 lantiq: fix port indexing for WBMR-300
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-14 20:03:02 +01:00
Mathias Kresin
7fd5171a34 lantiq: use the device tree bindings from rt2x00 driver
Set a device specific wireless mac address for ARV7506PW11, VGV7519 and
VGV7510KW22. The one from the EEPROM is a generic one and the same on
all boards.

Use the wifi@0,0 label and the pci0,0 compatible string for the
ARV7519PW and ARV7525PW since the pci vendor and device id is unknown.
It should work anyway since the compatible string isn't evaluated
(yet).

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-09 20:02:18 +01:00
Mathias Kresin
13208e89d0 lantiq: fix VGV7519 and VGV7510KW22 mac addresses
The VGV7510KW22 stock firmware uses the following mac-addresses:

lan      (ifno 1): AA:BB:CC:DD:EE:60
wlan     (ifno 2): AA:BB:CC:DD:EE:61
atm0     (ifno 3): AA:BB:CC:DD:EE:62
atm1/wan (ifno 4): AA:BB:CC:DD:EE:63

The VGV7519 stock firmware uses the following mac-addresses:

lan:  AA:BB:CC:DD:EE:EF
wlan: AA:BB:CC:DD:EE:EF
wan:  AA:BB:CC:DD:EE:EE

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-09 20:02:18 +01:00
Mathias Kresin
17094e9e64 lantiq: rework VG3503J image
Use the new image build code and remove the lzma loader. The lzma
loader was used to cheat the signature validation of the bootloader and
I found another way to do this.

To migrate boards already using LEDE/OpenWrt to the new image the
following steps need to be done once:

  VR9 # run reset_uboot_config
  VR9 # reset
  VR9 # setenv ethaddr AA:BB:CC:DD:EE:FF
  VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
  VR9 # saveenv
  VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
  VR9 # erase 0xb0020000 $(filesize)
  VR9 # cp.b 0x81000000 0xb0020000 $(filesize)

The mac address is printed on the label at the bottom of the case.

The following steps are need to be done during first install:

  VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
  VR9 # saveenv
  VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
  VR9 # erase 0xb0020000 $(filesize)
  VR9 # cp.b 0x81000000 0xb0020000 $(filesize)

The image uses the uImage firmware splitter now instead of hardcoded
kernel and rootfs partitions. The firmware partition size was extended
to use flash space that was reserved for partitions required only by
the ECI firmware.

Due to the changes an upgrade to a later LEDE revision from a running
LEDE is supported now.

A default switch config was added and the device uses the same MAC
addresses as the ECI firmware now instead of the same for all VG3503J.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:06:15 +02:00
Mathias Kresin
36afaae847 lantiq: use wpad-mini for WBMR boards
The WBMR boards are the only ones in the whole tree selecting the wpad
and hostapd-utils package by default.

Remove the wps uci-default script as well, there is no obvious reason
why the wps config need to be set only for this board.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
0547b3ca64 lantiq: fix lantiq-dsl output spam
In case the adsl/vdsl service is disabled intentional, the output is
cluttered with the following message multiple times if the status of
the dsl line is queried:

  killall: vdsl_cpe_control: no process killed

If the dsl line status is queried by LuCI, the logfile is spammed with
the message.

Fix the issue by using killall in quite mode. In quite mode killall
still returns a non-zero value if the to be killed process can not be
found so that existing logic based on the return value still works.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-11 09:31:57 +02:00
Mathias Kresin
e07c80dfc8 lantiq: use aliases device tree node for leds
The chosen node is clearly the wrong place for aliases.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-05 19:23:23 +02:00
Mathias Kresin
8b639410d1 lantiq: cleanup led handling functions
Use a more generic name for the lantiq_get_dt_led_chosen function.

Drop the lantiq_is_dt_led_chosen function. The lantiq_get_dt_led
function can be used to achieve the same.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-05 19:23:23 +02:00
Mathias Kresin
dbb13a81b9 lantiq: board.d: apply alphabetical order to led file
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-05 19:23:23 +02:00
Jo-Philipp Wich
1c09849f6c treewide: remove bad local shell variable declarations
Local variable declarations outside of functions are illegal since the Busybox
update to v1.25.0, therfore remove them from the appropriate places.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-09-24 14:38:20 +02:00
Martin Blumenstingl
e9de6e5203 lantiq: do not "local" variables outside of a function
Older busybox versions allowed using the local keyword outside of
functions, whereas 1.25.0 (which was introduced in 06fa1c46fc) do not
allow this anymore (leading to the following error when executing the
script: "file: local: line nn: not in a function").

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2016-09-24 01:17:17 +02:00
Mathias Kresin
c1578d4fc9 cleanup ucidef_set_interface* usage
- quote the interface name
- remove call of not existing function
- remove the proto if it's the default proto

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-10 15:32:25 +02:00
Mathias Kresin
64d72880bc lantiq: board.d: apply alphabetical order
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-10 15:28:38 +02:00
Mathias Kresin
96f6bd501a lantiq: board.d: cleanup default switch config
Add or fix the physical port number of switch ports to allow LuCI to
display the ports in physical order.

Remove the physical port number in case bridge port and physical port
order are the same.

Reorder the ucidef_add_switch parameter to be aligned with the switch
port number.

Remove board settings which are covered by the default case and remove
comments.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-10 15:28:38 +02:00
Sigurd Hogsbro
63857a2d6a lantiq: generate switch configuration for BTHOMEHUBV2B.
Split from HH3A as it appears to have a different switch.
https://en.wikipedia.org/wiki/BT_Home_Hub#Models_and_technical_specifications

Signed-off-by: Sigurd Hogsbro <sigurd@hogsbro.org>
2016-08-20 05:35:42 +02:00
Mathias Kresin
0b327c1652 lantiq: board.d: set lan mac address only where necessary
Do not set the lan mac address for boards which having the lan mac
address already set in device tree source file.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-10 02:04:31 +02:00
Hauke Mehrtens
47cce1d5e4 lantiq: fix switch configuration for EASY80920
The device tree description misses some Ethernet ports and there was no
model specified for this board. In addition there was no switch
specific default configuration created.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-07-28 22:42:16 +02:00
Felix Fietkau
eb28a0cde6 lantiq: fix WBMR-300HPD switch port assignment
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-28 21:25:42 +02:00
Mathias Kresin
f080cfab72 lantiq: fix network in failsafe
So far the network in failsafe is setup only for one board. Use the
eth0 interface as lan interface for all boards for now.

If a board has its lan interface(s) on another eth, a special
handling based on the board name can be added.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-06-22 19:32:06 +02:00
Oswald Buddenhagen
9759fde40a lantiq: add support for ARV7506PW11 (Alice/O2 IAD 4421)
Ethernet, ADSL2+ and LEDs are fully functional.

Supporting the two TAE ports and SIP gateway was not attempted.

The WiFi is unreliable, due to experimental support for rt35xx family
devices by the rt2800pci driver.

Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
[rebase to LEDE HEAD]
[switch to normal image instead of brnboot image]
[remove not required pinmux child nodes keys, leds, ebu, exin, pci_in and pci_out]
[remove switch_rst pinmux child node (no support for hw reset in driver/setting a default GPIO value in DT]
[enable usage of the wireless LED]
[fixup mac address configuration]
Sgned-off-by: Mathias Kresin <dev@kresin.me>
2016-06-22 19:32:06 +02:00
John Crispin
f054e82bdc lantiq: remove gr7000 support
this seems to have never worked as the wrong SoC is selected

Signed-off-by: John Crispin <john@phrozen.org>
2016-06-22 19:32:06 +02:00
Mathias Kresin
551c9c8300 lantiq: diag - switch off the power led on failsafe
This patch is a follow up to commit 4cf3fd4 "add support for indicating
the boot state using three leds".

At the time of writing the patch, I wasn't aware that it's possible to
switch info failsafe after boot (factory reset).

Enabling the failsafe led without disabling the running led causes an
unexpected led colour on devices using a single multicolour led to
indicate the boot state.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-06-20 11:45:44 +02:00
Felix Fietkau
a285f1895b Revert "lantiq: Use correct macaddr generating logic for the DGN3500"
This reverts commit 492964e741, which
makes no sense. /etc/board.d cannot be used for system init stuff.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-15 18:40:48 +02:00
John Crispin
88019c6c77 lantiq: add ARV4525PW wifi led
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 06:43:02 +02:00
John Crispin
d5666b98fa lantiq: fix fritz7320 wifi support
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 06:43:02 +02:00
John Crispin
d5143a49b7 lantiq: add AVM image mageic to sysupgrade script
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:43 +02:00
John Crispin
bf007a480a lantiq: Add Support for Fritz!Box 7360 SL
Signed-off-by: Sebastian Ortwein <krone@animeland.de>
Tested-by: Guido Lipke <lipkegu@gmail.com>
2016-06-13 22:51:43 +02:00
John Crispin
027da34957 lantiq: add default lan setup to board.d script
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:41 +02:00
Felix Fietkau
2d48f93ff4 lantiq: add Buffalo WBMR-300HPD support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-11 09:49:13 +02:00
Daniel Gimpelevich
492964e741 lantiq: Use correct macaddr generating logic for the DGN3500
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2016-05-27 16:08:47 +02:00
Mathias Kresin
1e395608cc lantiq: VGV7519 - add vlan support
Add the lantiq,switch property to enable vlans and setup them up.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:16 +02:00
Mohammed Berdai
f778cdd9c9 lantiq: fix ARV4518PWR01 network
This patch fixes the missing Lan interface config in the file
/etc/config/network for ARV4518PWR01/A which results in eth0 and br-lan
being down and therefore no way to access the router unless via UART-TTL.

Signed-off-by: Mohammed Berdai <mohammed.berdai@gmail.com>
2016-05-27 15:50:16 +02:00
John Crispin
dc92917409 image / basefiles: make console password configurable
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
Signed-off-by: John Crispin <john@phrozen.org>
2016-04-18 21:53:07 +02:00
John Crispin
0a4f2b5920 lantiq: Fix typo in LED diag script.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Acked-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49242
2016-04-26 11:43:31 +00:00
John Crispin
0039bc665c lantiq-dsl: add missing blank in dsl output
blank inserted before ACTATP

Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>

SVN-Revision: 49137
2016-04-09 10:25:29 +00:00
John Crispin
c701c3ce77 lantiq-dsl: bugfix latency values swapped for lucistat
swapped wrong latency output

Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>

SVN-Revision: 49136
2016-04-09 10:25:24 +00:00
John Crispin
7beb53b1a5 lantiq-dsl: bugfix db negative sign after comma
If db is negative minus sign was shown after comma

Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>

SVN-Revision: 49135
2016-04-09 10:25:20 +00:00