Commit Graph

8 Commits

Author SHA1 Message Date
Soma Zambelly
c5b44af2fc realtek: add ZyXEL GS1900-24HPv2 support
The ZyXEL GS1900-24HPv2 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches.

Specifications
--------------
* Device:    ZyXEL GS1900-24HPv2
* SoC:       Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash:     16 MiB
* RAM:       W631GG8MB-12 128 MiB DDR3 SDRAM
             (stock firmware is configured to use only 64 MiB)
* Ethernet:  24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:      1 PWR LED (green, not configurable)
             1 SYS LED (green, configurable)
             24 ethernet port link/activity LEDs (green, SoC controlled)
             24 ethernet port PoE status LEDs
             2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:   1 "RESTORE" button on front panel
             1 "RESET" button on front panel
* Power      120-240V AC C13
* UART:      1 serial header (J41) with populated standard pin connector on
             the left edge of the PCB, angled towards the side.
             The casing has a rectangular cutout on the side that provides
             external access to these pins.
             Pinout (front to back):
             + GND
             + TX
             + RX
             + VCC

Serial connection parameters for both devices: 115200 8N1.

Installation
------------

OEM upgrade method:

(Possible on master once https://patchwork.ozlabs.org/project/openwrt/patch/20210624210408.19248-1-bjorn@mork.no/ is merged)

* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
  flashed to the "Active" partition. If the second option is selected,
  OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
  file by your preferred method to the previously determined partition.
  When prompted, select to boot from the newly flashed image, and reboot the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
   > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
   it may be necessary to restart the network (/etc/init.d/network restart) on
   the running initramfs image.

U-Boot TFTP method:

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:
   > rtk network on
* Since the GS1900-24HPv2 is a dual-partition device, you want to keep the OEM
  firmware on the backup partition for the time being. OpenWrt can only boot
  from the first partition anyway (hardcoded in the DTS). To make sure we are
  manipulating the first partition, issue the following commands:
  > setsys bootpartition 0
  > savesys
* Download the image onto the device and boot from it:
   > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
   > bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
   > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
   it may be necessary to restart the network (/etc/init.d/network restart) on
   the running initramfs image.

Signed-off-by: Soma Zambelly <zambelly.soma@gmail.com>
2021-09-13 18:36:15 +02:00
Rafał Miłecki
4b9a67362d base-files: generate network config with "device" options
Replace "ifname" with "device" as netifd has been recently patches to
used the later one. It's more clear and accurate.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-05-27 10:58:49 +02:00
Raylynn Knight
c829bc1f2c realtek: Add support for Netgear S350 series switches GS308T and GS310TP
The Netgear GS308T v1 is an 8 port gigabit switch.  The GS310TP v1 is an 8
port POE+ gigabit switch with 2 SFP Ports (currently untested).

The GS308T v1 and GS310TP v1 are quite similar to the Netgear GS1xx
devices already supported.  Theses two devices use the same Netgear
firmware and are very similar to there corresponding GS1xx devices. For
this reason they share a large portion of the device tree with the GS108T
and GS110TP with exception of the uimage magic and model and compatible
values.

All of the above feature a dual firmware layout, referred to as Image0
and Image1 in the Netgear firmware.

In order to manipulate the PoE+ on the GS310TP v1 , one needs the
rtl83xx-poe package

Specifications (GS308T)
----------------------

 * RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz
 * 128MB DDR3-1600 DRAM (Winbond W631GG8MB-12)
 * 32MB 3v NOR SPI Flash (Winbond W25Q256JVFQ)
 * RTL8231 GPIO extender to control the LEDs and the reset button
 * 8 x 10/100/1000BASE-T ports, internal PHY (RTL8218B)
 * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J1
 * Power is supplied via a 12V 1A barrel connector

Specifications (GS310TP)
----------------------

 * RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz
 * Nuvoton M0516LDN for controlling PoE
 * 128MB DDR3-1600 DRAM (Winbond W631GG8MB-12)
 * 32MB 3v NOR SPI Flash (Winbond W25Q256JVFQ)
 * RTL8231 GPIO extender to control the LEDs and the reset button
 * 8 x 10/100/1000BASE-T PoE+ ports, 2 x Gigabit SFP ports,
 internal PHY (RTL8218B)
 * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J1
 * Power is supplied via a 54V 1.25A barrel connector

Both devices have UART pinout
-----------

J1 | [o]ooo
      ^ ||`------ GND
      | |`------- RX         [TX out of the serial adapter]
      | `-------- TX         [RX into the serial adapter]
      `---------- Vcc (3V3)  [the square pin]

The through holes are filled with PB-free solder which melts at 375C.
They can also be drilled using a 0.9mm bit.

Installation
------------
Instructions are identical to those for the similar Negear devices
and apply both to the GS308T v1 and GS310TP v1 as well.
-------------------
Boot initramfs image from U-Boot
--------------------------------

 1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt
 2. Init network with `rtk network on` command
 3. Load image with `tftpboot 0x8f000000
openwrt-realtek-generic-netgear_gs308t-v1-initramfs-kernel.bin` command
 4. Boot the image with `bootm` command

The switch defaults to IP 192.168.1.1 and tries to fetch the image via
TFTP from 192.168.1.111.

Updating the installed firmware
-------------------------------

The OpenWRT ramdisk image can be flashed directly from the Netgear UI.
The Image0 slot should be used in order to enable sysupgrade.

As with similar switches, changing the active boot partition can be
accomplished in U-Boot as follows:

 1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt
 2. Run `setsys bootpartition {0|1}` to select the boot partition
 3. Run `savesys` followed by `boota` to proceed with the boot process

Signed-off-by: Raylynn Knight <rayknight@me.com>
2021-05-07 07:05:16 +02:00
Adrian Schmutzler
85b1f4d8ca treewide: remove execute bit and shebang from board.d files
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.

Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.

Note:

This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-06 11:30:06 +01:00
Stijn Segers
c4bfe68c83 realtek: add support for ZyXEL GS1900-8HP v1 and v2
The ZyXEL GS1900-8HP is an 8 port gigabit switch with PoE+ support.
There are two versions on the market (v1 & v2) which share similar
specs (same flash size and flash layout, same RAM size, same PoE+ power
envelope) but have a different case and board layout that they each
share with other GS1900 siblings.

The v1 seems to share its PCB and case with non-PoE GS1900-8; as such,
adding support for the GS1900-8 would probably be trivial. The v2 seems
to share its casing and platform with its already supported bigger
brother, the GS1900-10HP - its board looks the same, except for two
holes where the GS1900-10 has its SFP ports.

Like their 10 port sibling, both devices have a dual firmware layout.
Both GS1900-8HP boards have the same 70W PoE+ power budget. In order to
manipulate the PoE+, one needs the rtl83xx-poe package [1].

After careful consideration it was decided to go with separate images
for each version.

Specifications (v1)
-------------------
* SoC:       Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash:     Macronix MX25L12835F 16 MiB
* RAM:       Nanya NT5TU128M8HE-AC 128 MiB DDR2 SDRAM
* Ethernet:  8x 10/100/1000 Mbit
* PoE+:      Broadcom BCM59111KMLG (IEEE 802.3at-2009 compliant, 2x)
* UART:      1 serial header with populated standard pin connector on the
             left side of the PCB, towards the bottom. Pins are labeled:
             + VCC (3.3V)
             + TX
             + RX
             + GND

Specifications (v2)
-------------------
* SoC:       Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash:     Macronix MX25L12835F 16 MiB
* RAM:       Samsung K4B1G0846G 128 MiB DDR3 SDRAM
* Ethernet:  8x 10/100/1000 Mbit
* PoE+:      Broadcom BCM59121B0KMLG (IEEE 802.3at-2009 compliant)
* UART:      1 angled serial header with populated standard pin connector
             accessible from outside through the ventilation slits on the
             side. Pins from top to bottom are clearly marked on the PCB:
             + VCC (3.3V)
             + TX
             + RX
             + GND

Serial connection parameters for both devices: 115200 8N1.

Installation
------------
Instructions are identical to those for the GS1900-10HP and apply both
to the GS1900-8HP v1 and v2 as well.

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
  image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:
  > rtk network on
* Since the GS1900-10HP is a dual-partition device, you want to keep the
  OEM firmware on the backup partition for the time being. OpenWrt can
  only boot off the first partition anyway (hardcoded in the DTS). To
  make sure we are manipulating the first partition, issue the following
  commands:
  > setsys bootpartition 0
  > savesys
* Download the image onto the device and boot from it:
  > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8hp-v{1,2}-initramfs-kernel.bin
  > bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
  > sysupgrade /tmp//tmp/openwrt-realtek-generic-zyxel_gs1900-8hp-v{1,2}-squashfs-sysupgrade.bin

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[merge PoE case, keep device definitions separate, change all those
hashes in the commit message to something else so they don't get
removed when changing the commit ...]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-08 20:48:22 +01:00
Stijn Segers
ac16e6b2ea realtek: set PoE power budget for ZyXEL GS1900-10HP
As per the manufacturer's specifications, set the GS1900-10HP PoE power
budget to 77W.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2021-01-07 19:51:50 +01:00
John Crispin
9aa4490502 realtek: clean up board.json generation
In this new setup the switch is treated as wan, lan1.100 is used as
our mgmt vlan.

The board mac is applied to eth0, switch and switch.1

The board mac is assigned with the LA bit set to all lan ports while
incrementing it.

Signed-off-by: John Crispin <john@phrozen.org>
2020-12-02 07:53:21 +01:00
John Crispin
2b88563ee5 realtek: update the tree to the latest refactored version
* rename the target to realtek
* add refactored DSA driver
* add latest gpio driver
* lots of arch cleanups
* new irq driver
* additional boards

Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: John Crispin <john@phrozen.org>
2020-11-26 13:29:27 +01:00