Commit Graph

17647 Commits

Author SHA1 Message Date
Florian Beverborg
22e568d0fe hostapd: add support for custom per-BSS options
This adds an option "hostapd_bss_options" that does the same as
"hostapd_options" but on a per-BSS level, instead of a per-device level.

This can be used, for example, to configure different per-devce sae_passwords
per BSS or to augment some of the existing per-BSS options.

Signed-off-by: Florian Beverborg <flo@beverb.org>
[remove whitespace errors, bump release]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-01-03 12:31:42 -10:00
Felix Fietkau
3a12c6679e mac80211: replace legacy minstrel with minstrel_ht, improve rate selection
Legacy minstrel is essentially unmaintained and was showing poor performance
Replace it with minstrel_ht and improve rate selection and sampling behavior

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-01-03 12:56:40 +01:00
Felix Fietkau
55e23f2c02 wolfssl: enable HAVE_SECRET_CALLBACK
Fixes wpad-wolfssl build

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-01-02 14:36:25 +01:00
Hauke Mehrtens
e7d0d2e9dc wolfssl: Fix hostapd build with wolfssl 4.6.0
This fixes the following build problem in hostapd:
mipsel-openwrt-linux-musl/bin/ld: /builder/shared-workdir/build/tmp/ccN4Wwer.ltrans7.ltrans.o: in function `crypto_ec_point_add':
<artificial>:(.text.crypto_ec_point_add+0x170): undefined reference to `ecc_projective_add_point'
mipsel-openwrt-linux-musl/bin/ld: <artificial>:(.text.crypto_ec_point_add+0x18c): undefined reference to `ecc_map'
mipsel-openwrt-linux-musl/bin/ld: /builder/shared-workdir/build/tmp/ccN4Wwer.ltrans7.ltrans.o: in function `crypto_ec_point_to_bin':
<artificial>:(.text.crypto_ec_point_to_bin+0x40): undefined reference to `ecc_map'

Fixes: ba40da9045 ("wolfssl: Update to v4.6.0-stable")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-01-01 22:10:20 +01:00
Alexandru Ardelean
5eaf6d8bea libevent2: trigger rebuild on libevent2-pthreads
The symbol determines if the libevent2-pthreads libraries get built or not.
If we want to select libevent2-pthreads, and these haven't been built, an
error will occur mentioning that there are no 'libevent_pthreads-2.1.so'
files.

Adding CONFIG_PACKAGE_libevent2-pthreads to PKG_CONFIG_DEPEND will make
sure that the libraries get re-built in case libevent2-pthreads is
selected.

Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
2021-01-01 10:26:20 -10:00
Oldřich Jedlička
49d678f0d2 base-files: allow reusing of boolean value extraction logic
The `functions.sh` script has `config_get_bool()` function, which is
usable when using UCI config direct access API, but there is no
equivalent for the callback API. Introduce `get_bool()` function to
allow reusing it from init scripts.

Example:

```sh
option_cb() {
    local option="$1"
    local value="$(get_bool "$2")"
    ...
}
```

Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
2021-01-01 10:23:56 -10:00
Rui Salvaterra
0f14aec8fc kernel/modules: remove fake users from udptunnel{4,6}
Since we're now able to select CONFIG_NET_UDP_TUNNEL at will, drop the fake
dependencies.

This is a partial revert of commit d7e040f8bc
"kernel: add fake users for udptunnel and iptunnel modules".

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-01-01 19:56:00 +01:00
Stijn Segers
59b5c52a6b cryptodev-linux: bump to 1.11, fix build against kernel 5.10.
This patch bumps cryptodev-linux to the latest stable release (1.11) and fixes
compilation against the next LTS (and likely OpenWrt) kernel 5.10.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2021-01-01 19:55:59 +01:00
Rosen Penev
f97b3ad726 trace-cmd: update to 2.9.1
Fixed license information.

Adjusted Makefile to new install paths.

Backported upstream patch to fix compilation with musl. Replaces local
and incomplete patch.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2021-01-01 19:55:59 +01:00
Hauke Mehrtens
7aa8c00e4b ppp: Remove already applied patch
This patch was already applied upstream and not needed here.

Fixes: 06403981e1 ("ppp: update to version 2.4.7.git-2019-05-06")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-01-01 19:55:59 +01:00
Eneas U de Queiroz
ba40da9045 wolfssl: Update to v4.6.0-stable
This version fixes a large number of bugs, although no security
vulnerabilities are listed.

Full changelog at:
https://www.wolfssl.com/docs/wolfssl-changelog/
or, as part of the version's README.md:
https://github.com/wolfSSL/wolfssl/blob/v4.6.0-stable/README.md

Due a number of API additions, size increases from 374.7K to 408.8K for
arm_cortex_a9_vfpv3-d16.  The ABI does not change from previous version.

Backported patches were removed; remaining patch was refreshed.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2021-01-01 19:55:59 +01:00
Russell Senior
c22b689cf8 iproute2: update to 5.10.0
c8faeca5 (ss: mptcp: fix add_addr_accepted stat print, 2020-11-18)
0d78e8ea (tc: pedit: fix memory leak in print_pedit, 2020-12-11)
ec1346ac (devlink: fix memory leak in cmd_dev_flash(), 2020-12-11)
309e6027 (man: tc-flower: fix manpage, 2020-12-11)
376367d9 (uapi: merge in change to bpf.h, 2020-12-14)
2e80ae89 (Merge branch 'gcc-10' into main, 2020-12-03)
755b1c58 (tc/mqprio: json-ify output, 2020-12-02)
975c4944 (ip/netns: use flock when setting up /run/netns, 2020-11-27)
fb054cb3 (uapi: update devlink.h, 2020-11-29)
c95d63e4 (uapi: update devlink.h, 2020-11-29)
cae2e929 (f_u32: fix compiler gcc-10 compiler warning, 2020-11-29)
c0149839 (misc: fix compiler warning in ifstat and nstat, 2020-11-29)
2319db90 (tc: fix compiler warnings in ip6 pedit, 2020-11-29)
5bdc4e91 (bridge: fix string length warning, 2020-11-29)
f8176999 (devlink: fix uninitialized warning, 2020-11-29)
7a49ff9d (bridge: report correct version, 2020-11-15)
8682f588 (tc-mpls: fix manpage example and help message string, 2020-11-02)
7c7a0fe0 (tc-vlan: fix help and error message strings, 2020-11-02)
72f88bd4 (uapi: update kernel headers from 5.10-rc2, 2020-11-08)
b90c39be (rdma: fix spelling error in comment, 2020-11-08)
c8424b73 (man: fix spelling errors, 2020-11-08)
cbf64817 (tc/m_gate: fix spelling errors, 2020-11-08)
14b189f0 (uapi: updates from 5.10-rc1, 2020-11-03)
9fc5bf73 (libnetlink: define __aligned conditionally, 2020-10-26)
eb12cc9a (Merge branch 'main' into next, 2020-10-25)
f1298d76 (m_mpls: test the 'mac_push' action after 'modify', 2020-10-22)
2b7a7684 (Merge branch 'tipc-encryption' into next, 2020-10-20)
2bf1ba5a (tipc: add option to set rekeying for encryption, 2020-10-16)
5fb36818 (tipc: add option to set master key for encryption, 2020-10-16)
b4edd6a8 (Merge branch 'tc-mpls-l2-vpn' into next Guillaume Nault  says:, 2020-10-20)
02a261b5 (m_mpls: add mac_push action, 2020-10-19)
d61167dd (m_vlan: add pop_eth and push_eth actions, 2020-10-19)
3342688a (devlink: display elapsed time during flash update, 2020-10-14)
cb7ce51c (v5.9.0, 2020-10-15)
b5a583fb (Merge branch 'main' into next Signed-off-by: David Ahern <dsahern@gmail.com>, 2020-10-11)
78120128 (genl: ctrl: print op -> policy idx mapping, 2020-10-03)
91c54917 (Merge branch 'bridge-igmpv3-mldv2' into next Nikolay Aleksandrov  says:, 2020-10-11)
86588450 (bridge: mdb: print protocol when available, 2020-10-08)
2de81d1e (bridge: mdb: print source list when available, 2020-10-08)
1d28c480 (bridge: mdb: print filter mode when available, 2020-10-08)
e331677e (bridge: mdb: show igmpv3/mldv2 flags, 2020-10-08)
f94e8b07 (bridge: mdb: print fast_leave flag, 2020-10-08)
547b3197 (bridge: mdb: add support for source address, 2020-10-08)
f905191a (Update kernel headers, 2020-10-11)
4322b13c (ip xfrm: support setting XFRMA_SET_MARK_MASK attribute in states, 2020-10-02)
8dc1db80 (devlink: Add health reporter test command support, 2020-10-01)
01216471 (devlink: support setting the overwrite mask attribute, 2020-09-30)
34be2d26 (Update kernel headers, 2020-10-07)
d2be31d9 (ss: add support for xdp statistics, 2020-09-24)
f481515c (Update kernel headers, 2020-09-29)
b8663da0 (ip: promote missed packets to the -s row, 2020-09-16)
cec67df9 (Merge branch 'devlink-controller-external-info' into next Parav Pandit  says:, 2020-09-22)
748cbad3 (devlink: Show controller number of a devlink port, 2020-09-18)
8fadd011 (devlink: Show external port attribute, 2020-09-18)
454429e8 (Update kernel headers, 2020-09-22)
ad34d5fa (iproute2: ss: add support to expose various inet sockopts, 2020-08-19)
c8eb4b52 (Update kernel headers, 2020-09-08)
abee772f (tipc: support 128bit node identity for peer removing, 2020-08-27)
6fd53b2a (iplink: add support for protodown reason, 2020-08-28)
af27494d (ip xfrm: support printing XFRMA_SET_MARK_MASK attribute in states, 2020-08-28)
275eed9b (Merge branch 'main' into next, 2020-09-01)
cc889b82 (genl: ctrl: support dumping netlink policy, 2020-08-24)
d5acae24 (libnetlink: add nl_print_policy() helper, 2020-08-24)
784fa9f6 (libnetlink: add rtattr_for_each_nested() iteration macro, 2020-08-24)

OpenWrt patches unchanged.
Successfully built for ramips/mt7621 and x86/geode with:

CONFIG_PACKAGE_devlink=m
CONFIG_PACKAGE_genl=m
CONFIG_PACKAGE_ip-bridge=m
CONFIG_PACKAGE_ip-full=m
CONFIG_PACKAGE_ip-tiny=m
CONFIG_PACKAGE_nstat=m
CONFIG_PACKAGE_rdma=m
CONFIG_PACKAGE_ss=m
CONFIG_PACKAGE_tc=m

Minimally run-tested ip-tiny on ramips/mt7621 (ubnt-erx).

Signed-off-by: Russell Senior <russell@personaltelco.net>
2021-01-01 13:22:58 +01:00
Felix Fietkau
e1851720f1 hostapd: do not restart hostapd instance on wireless restarts
Add the flag that prevents netifd from killing hostapd/wpa_supplicant

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-12-31 14:26:00 +01:00
Felix Fietkau
a7ff013eb6 netifd: update to the latest version
39fb8c3edc74 wireless: add support for not killing processes on teardown

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-12-31 14:25:59 +01:00
Johannes Kimmel
3f5619f259 vxlan: allow for dynamic source ip selection (FS#3426)
By setting 'auto', the zero address or the empty string as source
address (option ipaddr, option ip6addr), vxlan will choose one
dynamically. This helps in setups where a wan ip or prefix changes.

This corresponse to setting up an vxlan tunnel with:

proto vxlan6:
    # ip link add vx0 type vxlan id ID local :: ...
proto vxlan:
    # ip link add vx0 type vxlan id ID local 0.0.0.0 ...

While it is possible to not specify a source ip at all, the kernel will
default to setting up a ipv4 tunnel. The kernel will take any hint from
source and peer ips to figure out, what tunnel type to use. To make sure
we setup an ipv6 tunnel for proto vxlan6, this workaround is needed.

This will not change the behaviour of currently working configurations.
However this will allow former broken configurations, namely those not
specifying both a source address and tunnel interface, to setup a
tunnel interface. Previously those configurations weren't reporting an
error and were stueck in a setup loop like in Bug FS#3426.

This change lifts the currently very strict behaviour and should fix the
following bug:

Fixes: FS#3426
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3426

Signed-off-by: Johannes Kimmel <fff@bareminimum.eu>
2020-12-31 11:53:21 +01:00
Sven Eckelmann
80713657b2 ath79: Add support for OpenMesh OM5P
Device specifications:
======================

* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 5 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + builtin switch port 1
    + used as LAN interface
  - eth1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

WAN/LAN LEDs appear to be wrong in ar71xx and have been swapped here.

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[add LED swap comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-12-30 23:32:07 +01:00
Sven Eckelmann
ff9e48e75c ath79: Add support for OpenMesh OM2P v2
Device specifications:
======================

* Qualcomm/Atheros AR9330 rev 1
* 400/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + builtin switch port 1
    + used as LAN interface
  - eth1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* external antenna

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to
the device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-30 23:32:07 +01:00
Sven Eckelmann
eb3a5ddba0 ath79: Add support for OpenMesh OM2P-LC
Device specifications:
======================

* Qualcomm/Atheros AR9330 rev 1
* 400/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + builtin switch port 1
    + used as LAN interface
  - eth1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to
the device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-30 23:32:07 +01:00
Hans Dedecker
23fec971ca odhcp6c: update to git HEAD
eac1961 dhcpv6: fix displaying IA info
0475e18 dhcpv6: display status code as a string

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2020-12-30 20:20:06 +01:00
Adrian Schmutzler
93b6122212 base-files: sysupgrade: add function for conffiles retrieval
The find command to retrieve files from /etc/sysupgrade.conf and
/lib/upgrade/keep.d/* is used twice in almost the same way.

Move it into a function to consolidate, enhance readability and make
future adjustments easier.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
2020-12-30 00:00:13 +01:00
Maxim Storchak
f17c300983 busybox: define BUSYBOX_SYM before the first use
Since PKG_FILE_MODES relies on BUSYBOX_SYM, it should be defined early enough

Signed-off-by: Maxim Storchak <m.storchak@gmail.com>
2020-12-29 12:19:39 -10:00
Sven Eckelmann
75900a25ed ath79: add support for OpenMesh OM2P-HS v3
Device specifications:
======================

* Qualcomm/Atheros AR9341 rev 1
* 535/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + 802.3af POE
    + builtin switch port 1
    + used as LAN interface
  - eth1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to
the device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-29 00:03:26 +01:00
Sven Eckelmann
f096accce2 ath79: add support for OpenMesh OM2P-HS v2
Device specifications:
======================

* Qualcomm/Atheros AR9341 rev 1
* 535/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + 802.3af POE
    + builtin switch port 1
    + used as LAN interface
  - eth1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to
the device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-29 00:03:26 +01:00
Sven Eckelmann
a462412977 ath79: add support for OpenMesh OM2P-HS v1
Device specifications:
======================

* Qualcomm/Atheros AR9341 rev 1
* 535/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + 802.3af POE
    + builtin switch port 1
    + used as LAN interface
  - eth1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to
the device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[drop redundant status from eth1]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-12-29 00:03:26 +01:00
Rafał Miłecki
dbb542f194 bcm63xx-cfe: update to the latest master
c0b3691 netgear: r8000p: add cferam file
ae870eb asus: gt-ac5300: add cferam file
424b57c sfr: neufbox-6v-foxconn-r0: update cferam file
81a2a8b sfr: neufbox-6v-foxconn-r0: add cferam file
2730361 sercomm: h500-s: add cferam file

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-12-28 23:09:17 +01:00
Sven Eckelmann
5b37b52e69 ath79: Add support for OpenMesh OM2P-HS v4
Device specifications:
======================

* Qualcomm/Atheros QCA9533 v2
* 650/600/217 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + 24V passive POE (mode B)
    + used as WAN interface
  - eth1
    + 802.3af POE
    + builtin switch port 1
    + used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to
the device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-28 19:37:24 +01:00
Sven Eckelmann
dd1d95cb03 ath79: Add support for OpenMesh OM2P v4
Device specifications:
======================

* Qualcomm/Atheros QCA9533 v2
* 650/600/217 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + Label: Ethernet 1
    + 24V passive POE (mode B)
  - eth1
    + Label: Ethernet 2
    + 802.3af POE
    + builtin switch port 1
* 12-24V 1A DC
* external antenna

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to
the device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[wrap two very long lines, fix typo in comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-12-28 19:37:24 +01:00
Álvaro Fernández Rojas
e1938d3397 ath10k-ct-firmware: update to 022 (2020-11-08)
Runtime-tested on ath79 (TP-Link Archer C7 v2) and ipq806x (Netgear R7800).

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-12-28 18:07:34 +01:00
Álvaro Fernández Rojas
da9beb070d ath10k-ct: update to latest version
Changelog:
- ath10k-ct: Fix invalid use of ath-cb struct

Runtime-tested on ath79 (TP-Link Archer C7 v2) and ipq806x (Netgear R7800).

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-12-28 18:07:29 +01:00
Hans Dedecker
19d7e73ecc ethtool: update to version 5.10
The ipkg sizes changes as follows for mips 24kc :
	5.9  : ethtool_5.9-1_mips_24kc.ipk 35246
	5.10 : ethtool_5.10-1_mips_24kc.ipk 35385

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2020-12-26 20:39:25 +01:00
Yousong Zhou
1508841b4e kmod-tcp-hybla: new module for hybla congestion control algorithm
Just the module and no default sysctl conf file is provided

Link: https://forum.openwrt.org/t/20-xx-tcp-hybla/83076
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2020-12-26 10:08:08 +08:00
Yousong Zhou
d45b50389d kmod-tcp-bbr: use AutoProbe
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2020-12-26 10:08:08 +08:00
Yousong Zhou
72447181bc kmod-tcp-bbr: leave CONFIG_TCP_CONG_ADVANCED to target config
Since generic has the option set to y and other targets now inherit that
choice, there is no behaviour change

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2020-12-26 10:08:08 +08:00
Dongming Han
b9389186b0 ipq40xx: add support for GL.iNet GL-AP1300
Specifications:
SOC:        Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:        256 MiB
FLASH1:     4 MiB NOR
FLASH2:     128 MiB NAND
ETH:        Qualcomm QCA8075
WLAN1:      Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2:      Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT:      Reset
LED:        Power, Internet
UART1:      On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
OTHER:      On board with BLE module - by cp210x USB serial chip
            On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed

Install via uboot tftp or uboot web failsafe.

By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi
(IPQ40xx) # run lf

By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1

Afterwards upgrade can use sysupgrade image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
2020-12-25 10:38:13 +01:00
Yanase Yuki
3bb1618573 ipq806x: add support for NEC Platforms Aterm WG2600HP3
NEC Platforms Aterm WG2600HP3 is a dual-band router based on Qualcomm IPQ8062.

Specification
-------------
- SoC: Qualcomm IPQ8062
- RAM: 512MiB
- Flash memory: SPI-NOR 32MiB (Cypress S25FL256S)
- Wi-Fi: Qualcomm QCA9984 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm QCA9984 (5GHz, 36ch - 64ch, 100ch - 140ch)
- Ethernet: 4x 100/1000 Mbps (1x WAN, 4x LAN)
- LED: 6x green LED, 6x red LED
- Input: 2x tactile switch, 1x SP3T slide switch
- Serial console: 115200bps, through-hole J3
  - [  ] [GND] [  ] [TX] [RX] ----> DC jack
- Power: DC 12V 1.5A

This device does not support VHT160 and VHT80+80.
Custom BDFs are required to limit VHT capabilities.

Flash instructions
------------------
1. Setup TFTP server (IP address: 192.168.1.2)
2. Put initramfs image into TFTP server directory
3. Connect WG2600HP3 lan port and computer that runs TFTP server
4. Connect to the serial console
5. Interrupt booting by Esc key (password: chiron)
6. Execute the following commands
    # setenv bootcmd "nboot 0x44000000 1 0x860000"
    # saveenv
    # setenv ipaddr 192.168.1.1
    # setenv serverip 192.168.1.2
    # tftpboot 0x44000000 openwrt-ipq806x-generic-nec_wg2600hp3-initramfs-uImage
7. After booting OpenWrt initramfs image, backup SPI-NOR flash memory
8. Erase firmware partition
    # mtd erase firmware
9. Run sysupgrade

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
2020-12-25 10:38:13 +01:00
Sven Eckelmann
b4009f453c ipq-wifi: Fix suffix for Plasma Cloud PA2200 QCA4019 board-2.bin
The Makefile is rejecting all files with for a given prefix (here
"board-plasmacloud_pa2200") when it didn't match a known suffix. Instead it
stops the build with an error like:

  Makefile:135: *** Unrecognized board-file suffix '.ipq4019' for 'board-plasmacloud_pa2200.ipq4019'. Stop.

The correct suffix for the QCA4019/hw1.0 is qca4019 and not ipq4019.

Fixes: 4871fd2616 ("ipq40xx: add support for Plasma Cloud PA2200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-25 10:38:13 +01:00
Sven Eckelmann
1c557e27fd ipq-wifi: Fix suffix for Plasma Cloud PA1200 QCA4019 board-2.bin
The Makefile is rejecting all files with for a given prefix (here
"board-plasmacloud_pa1200") when it didn't match a known suffix. Instead it
stops the build with an error like:

  Makefile:135: *** Unrecognized board-file suffix '.ipq4019' for 'board-plasmacloud_pa1200.ipq4019'. Stop.

The correct suffix for the QCA4019/hw1.0 is qca4019 and not ipq4019.

Fixes: ea5bb6bbfe ("ipq40xx: add support for Plasma Cloud PA1200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-25 10:38:13 +01:00
Michael Pratt
33d26a9a40 ath79: add support for Senao Engenius EAP350 v1
FCC ID: U2M-EAP350

Engenius EAP350 is a wireless access point with 1 gigabit PoE ethernet port,
2.4 GHz wireless, external ethernet switch, and 2 internal antennas.

Specification:

  - AR7242 SOC
  - AR9283 WLAN			(2.4 GHz, 2x2, PCIe on-board)
  - AR8035-A switch		(GbE with 802.3af PoE)
  - 40 MHz reference clock
  - 8 MB FLASH			MX25L6406E
  - 32 MB RAM			EM6AA160TSA-5G
  - UART at J2			(populated)
  - 3 LEDs, 1 button		(power, eth, 2.4 GHz) (reset)
  - 2 internal antennas

MAC addresses:

  MAC address is labeled as "MAC"
  Only 1 address on label and in flash
  The OEM software reports these MACs for the ifconfig

  eth0	MAC	*:0c	art 0x0
  phy0	---	*:0d	---

Installation:

  2 ways to flash factory.bin from OEM:

  - if you get Failsafe Mode from failed flash:
      only use it to flash Original firmware from Engenius
      or risk kernel loop or halt which requires serial cable

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.10.1
    username and password "admin"
    Navigate to "Upgrade Firmware" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt uboot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9f670000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

Return to OEM:

  If you have a serial cable, see Serial Failsafe instructions
  otherwise, uboot-env can be used to make uboot load the failsafe image

  *DISCLAIMER*
  The Failsafe image is unique to Engenius boards.
  If the failsafe image is missing or damaged this will not work
  DO NOT downgrade to ar71xx this way, it can cause kernel loop or halt

  ssh into openwrt and run
  `fw_setenv rootfs_checksum 0`
  reboot, wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

Format of OEM firmware image:

  The OEM software of EAP350 is a heavily modified version
  of Openwrt Kamikaze. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-senao-eap350-uImage-lzma.bin
    openwrt-senao-eap350-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring.

  The OEM upgrade script is at /etc/fwupgrade.sh

  Later models in the EAP series likely have a different platform
  and the upgrade and image verification process differs.

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1024k
  and the factory.bin upgrade procedure would
  overwrite part of the kernel when writing rootfs.

Note on PLL-data cells:

  The default PLL register values will not work
  because of the external AR8035-A switch between
  the SOC and the ethernet PHY chips.

  For AR724x series, the PLL register for GMAC0
  can be seen in the DTSI as 0x2c.
  Therefore the PLL register can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x1805002c 1`.

  uboot did not have a good value for 1 GBps
  so it was taken from other similar DTS file.

Tested from master, all link speeds functional

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2020-12-25 10:38:13 +01:00
Michael Pratt
6c98edaae2 ath79: add support for Senao Engenius EAP600
FCC ID: A8J-EAP600

Engenius EAP600 is a wireless access point with 1 gigabit ethernet port,
dual-band wireless, external ethernet switch, 4 internal antennas
and 802.3af PoE.

Specification:

  - AR9344 SOC			(5 GHz, 2x2, WMAC)
  - AR9382 WLAN			(2.4 GHz, 2x2, PCIe on-board)
  - AR8035-A switch		(GbE with 802.3af PoE)
  - 40 MHz reference clock
  - 16 MB FLASH			MX25L12845EMI-10G
  - 2x 64 MB RAM		NT5TU32M16DG
  - UART at H1			(populated)
  - 5 LEDs, 1 button		(power, eth, 2.4 GHz, 5 GHz, wps) (reset)
  - 4 internal antennas

MAC addresses:

  MAC addresses are labeled MAC1 and MAC2
  The MAC address in flash is not on the label
  The OEM software reports these MACs for the ifconfig

  eth0	MAC 1	*:5e	---
  phy1	MAC 2	*:5f	---	(2.4 GHz)
  phy0	-----	*:60	art 0x0	(5 GHz)

Installation:

  2 ways to flash factory.bin from OEM:

  - if you get Failsafe Mode from failed flash:
      only use it to flash Original firmware from Engenius
      or risk kernel loop or halt which requires serial cable

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    Navigate to "Upgrade Firmware" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt uboot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9fdf0000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

Return to OEM:

  If you have a serial cable, see Serial Failsafe instructions
  otherwise, uboot-env can be used to make uboot load the failsafe image

  *DISCLAIMER*
  The Failsafe image is unique to Engenius boards.
  If the failsafe image is missing or damaged this will not work
  DO NOT downgrade to ar71xx this way, it can cause kernel loop or halt

  ssh into openwrt and run
  `fw_setenv rootfs_checksum 0`
  reboot, wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

Format of OEM firmware image:

  The OEM software of EAP600 is a heavily modified version
  of Openwrt Kamikaze. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-senao-eap600-uImage-lzma.bin
    openwrt-senao-eap600-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring.

  The OEM upgrade script is at /etc/fwupgrade.sh

  Later models in the EAP series likely have a different platform
  and the upgrade and image verification process differs.

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would
  overwrite part of the kernel when writing rootfs.

Note on PLL-data cells:

  The default PLL register values will not work
  because of the external AR8035-A switch between
  the SOC and the ethernet PHY chips.

  For AR934x series, the PLL register for GMAC0
  can be seen in the DTSI as 0x2c.
  Therefore the PLL register can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x1805002c 1`.

  Unfortunately uboot did not have the best values
  so they were taken from other similar DTS files.

Tested from master, all link speeds functional

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2020-12-25 10:38:13 +01:00
Michael Pratt
4a55ef639d ath79: add support for Senao Engenius ECB600
FCC ID: A8J-ECB600

Engenius ECB600 is a wireless access point with 1 gigabit PoE ethernet port,
dual-band wireless, external ethernet switch, and 4 external antennas.

Specification:

  - AR9344 SOC			(5 GHz, 2x2, WMAC)
  - AR9382 WLAN			(2.4 GHz, 2x2, PCIe on-board)
  - AR8035-A switch		(GbE with 802.3af PoE)
  - 40 MHz reference clock
  - 16 MB FLASH			MX25L12845EMI-10G
  - 2x 64 MB RAM		NT5TU32M16DG
  - UART at H1			(populated)
  - 4 LEDs, 1 button		(power, eth, 2.4 GHz, 5 GHz) (reset)
  - 4 external antennas

MAC addresses:

  MAC addresses are labeled MAC1 and MAC2
  The MAC address in flash is not on the label
  The OEM software reports these MACs for the ifconfig

  phy1	MAC 1	*:52	---	(2.4 GHz)
  phy0	MAC 2	*:53	---	(5 GHz)
  eth0	-----	*:54	art 0x0

Installation:

  2 ways to flash factory.bin from OEM:

  - if you get Failsafe Mode from failed flash:
      only use it to flash Original firmware from Engenius
      or risk kernel loop or halt which requires serial cable

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    Navigate to "Upgrade Firmware" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt uboot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9fdf0000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

Return to OEM:

  If you have a serial cable, see Serial Failsafe instructions
  otherwise, uboot-env can be used to make uboot load the failsafe image

  *DISCLAIMER*
  The Failsafe image is unique to Engenius boards.
  If the failsafe image is missing or damaged this will not work
  DO NOT downgrade to ar71xx this way, it can cause kernel loop or halt

  ssh into openwrt and run
  `fw_setenv rootfs_checksum 0`
  reboot, wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

Format of OEM firmware image:

  The OEM software of ECB600 is a heavily modified version
  of Openwrt Kamikaze. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-senao-ecb600-uImage-lzma.bin
    openwrt-senao-ecb600-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring.

  The OEM upgrade script is at /etc/fwupgrade.sh

  Later models in the ECB series likely have a different platform
  and the upgrade and image verification process differs.

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would
  overwrite part of the kernel when writing rootfs.

Note on PLL-data cells:

  The default PLL register values will not work
  because of the external AR8035-A switch between
  the SOC and the ethernet PHY chips.

  For AR934x series, the PLL register for GMAC0
  can be seen in the DTSI as 0x2c.
  Therefore the PLL register can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x1805002c 1`.

  Unfortunately uboot did not have the best values
  so they were taken from other similar DTS files.

Tested from master, all link speeds functional

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2020-12-25 10:38:13 +01:00
Hans Dedecker
bc99b56d7e odhcpd: update to latest git HEAD
b75bcad dhcpv6-ia: remove assignment equal to 0 checks
d1ae052 dhcpv6-ia: fix logic to include IA_PD prefix with lifetimes set to 0
9d5e379 dhcpv6-ia: fix prefix delegation behavior

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2020-12-24 17:23:41 +01:00
Daniel Golle
8348896357 opkg: update to git HEAD
9bbc7ea pkg_hash: pkg_hash_check_unresolved: fix segfault

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-12-24 11:12:57 +00:00
Dobroslaw Kijowski
1a9b896d8b treewide: nuke DRIVER_11W_SUPPORT
As of hostapd upstream commit 7d2ed8ba "Remove CONFIG_IEEE80211W build parameter"
https://w1.fi/cgit/hostap/commit?id=7d2ed8bae86a31dd2df45c24b3f7281d55315482
802.11w feature is always enabled in the build time.

It doesn't make sense to opt-in 802.11w per driver as hostapd will always
be compiled with this feature enabled.

As suggested by Hauke Mehrtens, for now keep 11w enabled in build_features.h
for compatibility reasons. This option will be dropped when LuCI is adjusted.

Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
2020-12-23 16:36:08 +01:00
Felix Fietkau
3d8d2c3a80 netifd: update to the latest version
88c6003e2b4f netifd: fix a typo in vlandev hotplug support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-12-23 11:22:23 +01:00
Piotr Dymacz
8c28da9724 base-files: drop banner.failsafe if failsafe is disabled
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2020-12-22 21:27:25 +01:00
Stefan Schake
d3c8881194 ipq40xx: add support for devolo Magic 2 WiFi next
SOC:     IPQ4018 / QCA Dakota
CPU:     Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7
DRAM:    256 MiB
NOR:     32 MiB
ETH:     Qualcomm Atheros QCA8075 (2 ports)
PLC:     MaxLinear G.hn 88LX5152
WLAN1:   Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:   Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:   RESET, WiFi, PLC Button
LEDS:    red/white home, white WiFi

To modify a retail device to run OpenWRT firmware:
1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT
   initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'.
2) Power on the device while pressing the recessed reset button next to
   the Ethernet ports. This causes the bootloader to retrieve and start
   the initramfs.
3) Once the initramfs is booted, the device will come up with IP
   192.168.1.1. You can then connect through SSH (allow some time for
   the first connection).
4) On the device shell, run 'fw_printenv' to show the U-boot environment.
   Backup this information since it contains device unique factory data.
5) Change the boot command to support booting OpenWRT:
   # fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm'
6) Change directory to /tmp, download the sysupgrade (e.g. through wget)
   and install it with sysupgrade. The device will reboot into OpenWRT.

Notice that there is currently no support for booting the G.hn chip.
This requires userland software we lack the rights to share right now.

Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
2020-12-22 20:55:40 +01:00
John Crispin
ceb612e463 hostapd: pass respawn settings when registering the service
When hostapd gets restarted to often/quickly will cause procd to not restart it
anymore. it will think that hapd is in a crash loop.

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [adjust respawn time]
2020-12-22 19:30:26 +01:00
Kip Porterfield
6ffe8a473e kirkwood: add support for Seagate BlackArmor NAS220
The Seagate BlackArmor NAS220 is a consumer NAS
with two internal drive bays. The stock OS runs
RAID 1 over the disks via mdadm.

Device specification:
- SoC: Marvell 88F6192 800 MHz
- RAM: 128 MB
- Flash: 32 MB
- 2 x internal SATA II drives
- Ethernet: 10/100/1000 Mbps (single port, no switch)
- WLAN: None
- LED: Power, Status, Sata Activity
- Key: Power, Reset
- Serial: 10 pin header, (115200,8,N,1), 3.3V TTL
	9|x  -   x|10
	7|x  -   x|8
	5|x  - GND|6
	3|x  -  RX|4
	1|TX -   x|2
	front of case
- USB ports: 2 x USB 2.0

Flash instruction:

NOTE: this process uses a serial connection. It will upgrade the
bootloader and reset the bootloader environment variables

TFTP server setup
- Setup PC with TFTP server set the PC IP to 10.4.50.5 as TFTP server
- Copy these files to TFTP server location
    - u-boot.kwb
    - seagate_blackarmor-nas220-initramfs-uImage
    - seagate_blackarmor-nas220-squashfs-sysupgrade.bin
    - seagate_blackarmor-nas220-squashfs-factory.bin

Seagate NAS setup
- Connect LAN cable between PC and seagate device
- Connect to serial to seagate device

Install u-boot
- Boot seagate device and stop in bootloader by pressing any key
- run 'printenv' from u-boot and save the values
- tftpboot 0x2000000 u-boot.kwb
- nand erase.part uboot
- nand write 0x2000000 0x0 ${filesize}
- reset

Update MAC address in u-boot env
- Stop in u-boot by pressing any key
- Get your MAC address from your saved printenv. Is also on chassis
- setenv ethaddr <your MAC>
- saveenv

Option 1 (recommended) - Install OpenWrt via initramfs and sysupgrade
- tftpboot 0x2000000 seagate_blackarmor-nas220-initramfs-uImage
- bootm 0x2000000
- *OpenWrt should be running now, however it is not written to flash yet*
- From the running instance of OpenWrt use Luci's "flash image" feature
    from the web site or use sysupgrade from the console to write
    seagate_blackarmor-nas220-squashfs-sysupgrade.bin to flash

Option 2 - Install OpenWrt by flashing factory image from u-boot
- nand erase.part ubi
- tftpboot 0x2000000 seagate_blackarmor-nas220-squashfs-factory.bin
- nand write 0x2000000 ubi ${filesize}
- reset

Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
2020-12-22 19:11:50 +01:00
Michael Pratt
fe2f53f21c ath79: add support for Senao Engenius EnStationAC v1
FCC ID: A8J-ENSTAC

Engenius EnStationAC v1 is an outdoor wireless access point/bridge with
2 gigabit ethernet ports on 2 external ethernet switches,
5 GHz only wireless, internal antenna plates, and proprietery PoE.

Specification:

  - QCA9557 SOC
  - QCA9882 WLAN		(PCI card, 5 GHz, 2x2, 26dBm)
  - AR8035-A switch		(RGMII GbE with PoE+ IN)
  - AR8031 switch		(SGMII GbE with PoE OUT)
  - 40 MHz reference clock
  - 16 MB FLASH			MX25L12845EMI-10G
  - 2x 64 MB RAM		NT5TU32M16FG
  - UART at J10			(unpopulated)
  - internal antenna plates	(19 dbi, directional)
  - 7 LEDs, 1 button		(power, eth, wlan, RSSI) (reset)

MAC addresses:

  MAC addresses are labeled as ETH and 5GHz
  Vendor MAC addresses in flash are duplicate

  eth0	ETH	*:d3	art 0x0/0x6
  eth1	----	*:d4	---
  phy0	5GHz	*:d5	---

Installation:

  2 ways to flash factory.bin from OEM:

  - if you get Failsafe Mode from failed flash:
      only use it to flash Original firmware from Engenius
      or risk kernel loop or halt which requires serial cable

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    Navigate to "Firmware" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt uboot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9fd70000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

Return to OEM:

  If you have a serial cable, see Serial Failsafe instructions
  otherwise, uboot-env can be used to make uboot load the failsafe image

  *DISCLAIMER*
  The Failsafe image is unique to Engenius boards.
  If the failsafe image is missing or damaged this will not work
  DO NOT downgrade to ar71xx this way, it can cause kernel loop or halt

  ssh into openwrt and run
  `fw_setenv rootfs_checksum 0`
  reboot, wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

TFTP recovery:

  rename initramfs to 'vmlinux-art-ramdisk'
  make available on TFTP server at 192.168.1.101
  power board
  hold or press reset button repeatedly

  NOTE: for some Engenius boards TFTP is not reliable
  try setting MTU to 600 and try many times

Format of OEM firmware image:

  The OEM software of EnStationAC is a heavily modified version
  of Openwrt Altitude Adjustment 12.09. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-ar71xx-enstationac-uImage-lzma.bin
    openwrt-ar71xx-enstationac-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring.

  Newer EnGenius software requires more checks but their script
  includes a way to skip them, otherwise the tar must include
  a text file with the version and md5sums in a deprecated format.

  The OEM upgrade script is at /etc/fwupgrade.sh.

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

Note on PLL-data cells:

  The default PLL register values will not work
  because of the external AR8033 switch between
  the SOC and the ethernet PHY chips.

  For QCA955x series, the PLL registers for eth0 and eth1
  can be see in the DTSI as 0x28 and 0x48 respectively.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x18050028 1` and `md 0x18050048 1`.

  For eth0 at 1000 speed, the value returned was
  ae000000 but that didn't work, so following
  the logical pattern from the rest of the values,
  the guessed value of a3000000 works better.

  later discovered that delay can be placed on the PHY end only
  with phy-mode as 'rgmii-id' and set register to 0x82...

Tested from master, all link speeds functional

Signed-off-by: Michael Pratt <mcpratt@pm.me>
[fixed SoB to match From:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-12-22 19:11:50 +01:00
Marek Lindner
4871fd2616 ipq40xx: add support for Plasma Cloud PA2200
Device specifications:

* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 36-64)
  - QCA9888 hw2.0 (PCI)
  - requires special BDF in QCA9888/hw2.0/board-2.bin
    bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 100-165)
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200
* GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE
* GPIO-LEDs for power (orange) and status (blue)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio3:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + used as LAN interface
  - phy@mdio4:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 802.3at POE+
    + used as WAN interface
* 12V 2A DC

Flashing instructions:

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-22 19:11:50 +01:00