the OOB layout in MTK SNFI uses the 2nd byte, and anything using OOB
will make the block a bad-block in spi-nand driver.
Hack it for now. We need a proper solution upstream.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Adresses of device tree nodes are typically noted without the '0x'
prefix. While having the '0x' prefix doesn't hurt when using Linux,
more recent versions of U-Boot will add a duplicate ramoops node as a
simple string compare is used to check if the node is already present.
Remove the '0x' prefix to avoid the kernel warning resulting from
U-Boot adding a dupplicate pstore/ramoops node.
See also https://lists.denx.de/pipermail/u-boot/2022-April/481810.html
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The MediaTek's Crypto Engine module is only available for mt7623, in
which case it is built into the kernel.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Use ARMv8 Crypto Extensions for AES, ghash and sha256.
This results in a 16 times speed gain in speed for aes-128-ctr, 17x in
aes-128-gcm, and 9 times in sha256.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This commit add some enabled symbols to generic config.
LTO is only supported by clang compiler and therefore should
be disabled in the generic config instead of duplicating this
symbol in each target. CONFIG_LTO_NONE do this job.
The second group of symbols is enabled by the options available
in the generic config and is therefore added here:
* CONFIG_AF_UNIX_OOB is selected by CONFIG_NET && CONFIG_UNIX,
* CONFIG_BINARY_PRINTF is selected by CONFIG_BPF_SYSCALL,
* CONFIG_NET_SOCK_MSG is selected by CONFIG_BPF_SYSCALL && CONFIG_NET.
The other symbols are disabled and should be in the generic config.
This commit also removes these symbols from subtargets.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Also known as the "Xiaomi Router AX3200" in western markets,
but only the AX6S is widely installation-capable at this time.
SoC: MediaTek MT7622B
RAM: DDR3 256 MiB (ESMT M15T2G16128A)
Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG)
WLAN: 2.4/5 GHz 4T4R
2.4 GHz: MediaTek MT7622B
5 GHz: MediaTek MT7915E
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531B
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8
Power: 12 VDC, 1.5 A
Notes:
U-Boot passes through the ethaddr from uboot-env partition,
but also has been known to reset it to a generic mac address
hardcoded in the bootloader.
However, bdata is also populated with the ethernet mac addresses,
but is also typically never written to. Thus this is used instead.
Installation:
1. Flash stock Xiaomi "closed beta" image labelled
'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'.
(MD5: 5eedf1632ac97bb5a6bb072c08603ed7)
2. Calculate telnet password from serial number and login
3. Execute commands to prepare device
nvram set ssh_en=1
nvram set uart_en=1
nvram set boot_wait=on
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
4. Download and flash image
On computer:
python -m http.server
On router:
cd /tmp
wget http://<IP>:8000/factory.bin
mtd -r write factory.bin firmware
Device should reboot at this point.
Reverting to stock:
Stock Xiaomi recovery tftp that accepts their signed images,
with default ips of 192.168.31.1 + 192.168.31.100.
Stock image should be renamed to tftp server ip in hex (Eg. C0A81F64.img)
Triggered by holding reset pin on powerup.
A simple implementation of this would be via dnsmasq's
dhcp-boot option or using the vendor's (Windows only)
recovery tool available on their website.
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
This patch moves the patches of parser_trx in mediatek target to
generic/backport-5.10 to use the changes from ramips target and
backport the additional patch of the parser.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
X32 Pro is another product name for it in the Chinese market.
Specifications:
- SoC: MT7622B
- RAM: 256MB
- Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR
- Ethernet: 5x1GbE
- Switch: MT7531BE
- WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN
- 3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red)
- 2Keys: Mesh button + Reset button
- UART: Marked J19 on board. 3.3v, 115200n1
- Power: 12V 2.5A
MAC addresses as verified by OEM firmware:
use address source
WAN *:F4 ethaddr@product_info
LAN *:F5
5g *:F6
2g *:F7
Flash instruction:
1. Serve the initramfs.img using a TFTP server with address 10.10.10.3.
2. Interrupt the uboot startup process via UART.
3. Select "System Load Linux to SDRAM via TFTP" item.
4. (important) Back up firmware(mtd7) partitions with:
dd if=/dev/mtd7 of=/tmp/firmware.bin
and then download the firmware.bin image via SCP.
5. Flash the OpenWrt sysupgrade firmware.
Recovery stock firmware:
1. Transfer the firmware.bin image to the device.
2. Flash the image with:
mtd write firmware.bin firmware
Signed-off-by: Langhua Ye <y1248289414@outlook.com>
Enable support for allocating user space page table entries in high memory [1],
for the targets which support this feature. This saves precious low memory
(permanently mapped, the only type of memory directly accessible by the kernel).
[1] https://www.kernel.org/doc/html/latest/vm/highmem.html
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
fwtool is now always part of the sysupgrade stage2 ramdisk, so drop
the no longer needed RAMFS_COPY_BIN variable.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that both, fw_printenv/fw_setenv and fwtool are always present
during stage2 sysupgrade, we no longer need to list them in
RAMFS_COPY_BIN and RAMFS_COPY_DATA in platform.sh.
Drop both variables as they are now unneeded.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Turns out the MT7531 switch IRQ line is connected to GPIO#53 just like
on the BPi-R64, so this seems to be part of the reference design and
will probably apply to most MT7622+MT7531 boards.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that we support link-state-change interrupts, wire up MT7531 IRQ
line which is connected to GPIO#53 according to the schematics [1].
As a result, PHY state no longer needs to be polled on that board.
[1]: https://forum.banana-pi.org/t/bpi-r64-mt7622-schematic-diagram-public/10118
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for MediaTek Gigabit Ethernet PHYs found in MT7530 and
MT7531. Fix some link up/down issues.
The errornous check for the PHY mode which broke things with MT7531
has been removed as suggested by patch
net: phy: mediatek: remove PHY mode check on MT7531
As a result, things are working fine now on MT7622+MT7531 as well.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
This reverts commit 8b4cba53a9.
This broke the mt7530 on Linksys e8450 (mt7622) for me.
[ 1.312943] mt7530 mdio-bus:00 lan1 (uninitialized): failed to connect to PHY: -EINVAL
[ 1.320890] mt7530 mdio-bus:00 lan1 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 0
[ 1.331163] mt7530 mdio-bus:00 lan2 (uninitialized): failed to connect to PHY: -EINVAL
[ 1.339085] mt7530 mdio-bus:00 lan2 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 1
[ 1.349321] mt7530 mdio-bus:00 lan3 (uninitialized): failed to connect to PHY: -EINVAL
[ 1.357241] mt7530 mdio-bus:00 lan3 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 2
[ 1.367452] mt7530 mdio-bus:00 lan4 (uninitialized): failed to connect to PHY: -EINVAL
[ 1.375367] mt7530 mdio-bus:00 lan4 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 3
[ 1.385750] mt7530 mdio-bus:00 wan (uninitialized): failed to connect to PHY: -EINVAL
[ 1.393575] mt7530 mdio-bus:00 wan (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 4
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for MediaTek Gigabit Ethernet PHYs found in MT7530.
Fix some link up/down issues.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
The two options 'emmc' and 'sdmmc' now became identical lines after
introducing CONFIG_TARGET_ROOTFS_PARTSIZE.
Remove the now useless if-clauses.
Fixes: a40b4d335a ("mediatek: use CONFIG_TARGET_ROOTFS_PARTSIZE")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Append 'earlycon=uart8250,mmio32,0x11004000' to the boot arguments
embedded in device-tree in order to enable early console on the
UniElec U7623 board when using the vendor/stock bootloader.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The legacy image for the UniElec U7623-02 until now included
kmod-ata-ahci-mtk. The MT7623 chip doesn't have that IP and that
board uses a PCIe-connected AHCI controller for the SATA port and
mSATA-pins of the mPCIe socket. Hence include kmod-ata-ahci instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
For devboards without a MAC address assigned from factory, store
the random MAC in U-Boot env on first boot to make it persistent.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add U-Boot env settings to allow accessing the environment using
fw_printenv and fw_setenv tools on the UniElec U7623 board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Users of older OpenWrt versions need sysupgrade using the *emmc.img.gz
file once which will upgrade U-Boot and switch to the new image layout.
Users of the vendor firmware need to first flash the legacy image to
then sunsequently carry out a full-flash upgrade.
Alternatively the board can also be flashed using MediaTek's
proprietary SP Flash Tool.
Configuration as well as persistent MAC address will be lost once at
this point and you will have to redo (or restore) all configuration
manually. To restore the previous persistent MAC address users may set
it manually using
fw_setenv ethaddr 00:11:22:33:44:55
For future upgrades once running OpenWrt past this commit, the usual
*sysupgrade.itb file can be used.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* Use serial0 instead of serial2 for the only serial port
* Add LED aliases
* Add ethernet0 alias to inherit ethaddr from U-Boot env
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable 'rootfs-part' feature to make the size of the partition of the
production image configurable instead of hard-coding it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Limit bmt remapping range to cover everything up to and including the kernel image,
use the rest of the flash area for ubi.
Fix partition table and sysupgrade support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Preparation for supporting BMT on MT7621. Move source files to the files/
subdirectory in order to simplify maintenance
Signed-off-by: Felix Fietkau <nbd@nbd.name>
CONFIG_ARM_ARCH_TIMER cannot be enabled in the config directly; it is only
selected by CONFIG_HAVE_ARM_ARCH_TIMER. We need to enable the latter in
our config.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fixes: 4f1c5b01c1 ("mediatek: mt7623: backport musb, improve HDMI console")
The Unielec U7623 doesn't have a physical power button; I think it's hard
wired so that it turns on automatically when power is applied (unlike the
Banana Pi R2 which is a pain).
So the 'reset on long press of power button' behaviour that we get when
we enable the PMIC keyboard driver is kind of unhelpful. Disable it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fixes: 0d3f3323a2 ("mediatek: mt7623: enable more hardware features")
The lowest frequency should be 300MHz, since that is the label
assigned to the OPP in the mt7622.dtsi device tree, while there is one
missing zero in the actual value.
To be clear, the lowest frequency should be 300MHz instead of 30MHz.
As mentioned @dangowrt on the OpenWrt forum there is no benefit in
leaving 30MHz as the lowest frequency.
Signed-off-by: Jip de Beer <gpk6x3591g0l@opayq.com>
Signed-off-by: Fritz D. Ansel <fdansel@yandex.ru>
To easy future maintainance, replace the local patch with what has been
accepted into net-next and is likely to end up in Linux 5.17.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
To allows Ethernet phys supporting 2500Base-T mode to announce that
speed, enable the corresponding bit in mtk_eth_soc driver.
This should hopefully unlock 2500Base-T speed on the UniFi 6 LR.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Upon comment of Russell King ('Oh no, not this "-1 disease" again.')
clean up mdio read and write return type and value in mtk_eth_soc
driver and also use appropriate return values for bus-busy-timeout-
errors in newly added Clause 45 access code.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Replace recently added patch
701-net-ethernet-mtk_eth_soc-add-support-for-clause-45-mdio.patch
with version sent upstream
701-net-ethernet-mtk_eth_soc-implement-Clause-45-MDIO-access.patch
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
