Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40477
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40475
The bootloader does not initializes the output function
correctly for all LEDs. DO that from the board setup code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40474
The hardware manual says amber so change the color part of
the LED names to reflect that. Also update the constant names.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40473
Everything seems to be working fine. Potential issues:
* VLAN port IDs are reversed with regard to the numbers on the case.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 40400
I don't have access to the specs, so I'm not sure about every detail, but I
haven't seen any problems with my test system, a TL-WR841N v9. It looks pretty
much like a QCA955x without PCI, a little twist in the clock calculation and
a AR9331-compatible switch.
Features not yet supported:
* EHCI (my test system doesn't have USB)
* ? (I have no idea if the QCA953x has any other features I don't know about
that aren't used by the TL-WR841N v9)
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 40399
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg:
- use a separate patch for kernel changes,
- reorder Kconfig and Makefile entries,
- change function and variable names to be lowercase only
and fix misaligned tabs in mach-gs-oolite.c,
... ]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40032
The flash address passed to rb_init_info() is bogus,
use the predefined AR71XX_SPI_BASE macro instead.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39891
sizeof(array_from_function_definition) gives back the size of the pointer.
sizeof(type) * array_size should be used in memset.
Signed-off-by: David Völgyes <david.volgyes@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4950/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39890
The RB91x boards are using a serial shift register
connected to the SPI bus to drive some of the LEDs.
Rework the board setup code to register a SPI device
for that. This makes it possible to use the 'spi-74x164'
driver to control the device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39703
I noticed that the patch at http://patchwork.openwrt.org/patch/4017/
for adding support for the MikroTik RouterBOARD 951Ui-2HnD had been
abandoned because it wasn't generated and sent to the mailing list
correctly and doesn't apply as a result. I have cleaned up this patch.
When testing this on real hardware, I also noticed that wireless didn't
work, so this patch fixes that as well.
This patch applies cleanly to SVN 39392.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Patchwork: http://patchwork.openwrt.org/patch/4773/
[juhosg:
- drop the 'rb951ui_wlan_init' function and rework the code to
use the recently introduced rb95x_wlan_init function instead,
- fix GPIO number of the port5 LED,
- rename LEDs according to the standard LED naming conventions,
and use 'rb' prefix in the names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39641
On recent TL-WDR4300 boards the external LNAs of the 2.4GHz
interface are connected to GPIO lines. Because these GPIO
lines are disabled by default, the RX sensitivity of the
device is quite bad.
Setup the GPIOs of the external LNAs to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39392
The eth5 LED on the RB2011 is not working because the
LED control rule is missing. Fix it.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39335
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.
Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Tested-by: Steven Haigh <netwiz@crc.id.au>
Patchwork: http://patchwork.openwrt.org/patch/4689/
[juhosg:
- remove the GPIO LED changes, the My Net N600 has no yellow LEDs at all,
- change subject and update the commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39214
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.
Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4688/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39213
The hardware supports large ethernet frames. Override
the maximum frame length and packet lenght mask in the
platform data to allow to use large MTU on the ethernet
interfaces.
Limit the feature to AR934x SoCs for now. It should work
on some other SoCs as well, but those has not been tested
yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39149
Now that the switch is working correctly I had the chance to actually
test the LED config.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4616/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39129
The bootloader on the WD My Net N750 disables the ports on it's internal
AR8327N switch by powering them down. The stock firmware then brings the
ports back up again by starting the auto negotiation process on each
port.
This fix implements just that.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4615/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39128
This enables us to add fixups to the board specific code for boards that
require special treatment of PHYs on mdio bus reset.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
http://patchwork.openwrt.org/patch/4614/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39127
This enables us to modify the ag71xx_mdio_platform_data from within the
board support files.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4613/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39126
It is only on RB911G-5HPnD and RB912UAG-5HPnD boards.
The LEDs and the USB port is not working yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39102
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: use a separate patch for kernel changes]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39077
The TL-WA801ND v2 board has only one LAN port which makes
it more similar to the TL-WR[78]50RE devices. Move the
board setup code into the mach-tl-wax50re.c file.
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39072
This way it is a bit easier to add other TP-LINK devices based on the
Atheros AP123 reference board with one LAN port.
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39071
Patch to add kernel support for the TP-LINK WA801ND v2
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4500/
[juhosg:
- the TL-WA801ND v2 does not have a sliding switch, it uses a push button
for WPS instead. Use the tl_mr3420v2_gpio_keys array to reflect that,
- rename kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39063
This patch improves support for the device considerably.
1. The wifi didn't work in the initial release. This was because
the WMAC of the AR9340 is not connected to the antennas.
(However, it can pick up wifi signals, if they are strong enough!)
Instead there's a dedicated AR9300 chip on the same board, which
works.
2. Ethernet throughput is improved. iperf shows that the hardware
can sustain more than 200Mbit/s and no longer drops any packages
when the link is under load.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4461/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38949
Just a small oversight my part, added the support for the USB led
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4425/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38946
Patch to add kernel support for the TP-LINK WA750RE and the WA850RE
range extender
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
[juhosg: rename and refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38717
This patch adds a new device definition for a
Western Digital device. The hardware seems to
be based on Qualcomm Atheros DB120 design.
Patchwork: http://patchwork.openwrt.org/patch/4281/
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
[juhosg: refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38686
BXU2000n-2 A1 is a BHU Networks WLAN board, use ar9341 chip.
Patchwork: http://patchwork.openwrt.org/patch/4183/
Signed-off-by: Terry Yang <yangbo@bhunetworks.com>
[juhosg:
- rename and refresh kernel patch,
- fix some checkpatch warnings and adjust whitespaces in
mach-bhu-bxu2000n2-a.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38591
This patch adds support for DRAGINO2 board (used by
Meshpotato v2). Most of the files included can be
found in the official svn repository provided by the
company [1]. I have just adapt it to the last OpenWrt
trunk revision (Fri Oct 4 10:49:47 2013).
1. http://svn.dragino.com/dragino2
Patchwork: http://patchwork.openwrt.org/patch/4234/
Signed-off-by: Pau Escrich <p4u@dabax.net>
[juhosg:
- rename and refresh kernel patch,
- fix checkpatch warnings in mach-dragino2.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38587
Fixes the 5 GHz LED.
The same function has no effect on the 2.4 GHz LED at all, so we might
as well remove it.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38482
This patch adds support for the hardware slide switch on
the TL-MR3040 v2.
Signed-off-by: Mads Hansen <d@taba.se>
[juhosg: use EV_SW instead of EV_KEY]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38190
This patch
- changes the color names from orange to amber
- changes the name of GPIO 13 from WIFI_BGN (wifi_bgn) to WLAN_2G
(wlan2g) to be more consistent with the other routers' files
- changes the descriptions of the hardware keys to be a tad more
explicit
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4081/
[juhosg: update the LED migration script as well]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38105
Enable GPIO 20. This hands off control of the blue planet led to the
integrated switch. Consequently, remove the led configuration for the
blue planet led.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4080/
[juhosg: whitespace fixup]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38096
This patches fixes the lan led configuration. The new configuration is
identical to the one in mach-db120.c and it works. The previous one
didn't work at all.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38094
Rename the function and extend it in order to make it
usable from board setup code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38085
This patch adds support for TP-Link TL-MR13U router with built-in 10AH
rechargeable battery.
The patch is based on kamwanlai's patch:
https://forum.openwrt.org/viewtopic.php?pid=206746#p206746
Updated to accommodate recent changes introduced with:
ar71xx: remove fs_* variables from image/Makefile
Signed-off-by: Oleg Titov <oleg.titov@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4063/
[juhosg:
- refresh and rename rename 930-add-tl-mr13u-support.patch =>
625-MIPS-ath79-add-tl-mr13u-support.patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38063
This patch adds OpenWRT support for the Netgear WNR2200 (N300)
wireless router with USB.
Technical details of this router can be found at
http://www.netgear.com/home/products/wirelessrouters/work-and-play/WNR2200.aspx
and http://wikidevi.com/wiki/Netgear_WNR2200
Signed-off-by: Aidan Kissane <aidankissane@googlemail.com>
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4055/
[juhosg:
- add commit message and SoB line from the original patch
- remove dead code from mach-wnr2200.c
- refresh 624-MIPS-ath79-WNR2200-support.patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38059
I checked the GPL code drop from D-Link and tried to get the wireless
and LAN switch LEDs to light up. I found some references in
AthSDK/www/DIR-825_C1/bsp.h as well as
AthSDK/www/DIR-825_C1/rootfs/etc/sysconfig/S2gpio.sh, but in the end I
only got the led for 2.4GHz to work. Anyway, here's the patch.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37963
Apparently registering usb device on newest trunk causes
this AP not to boot...
Since there is no USB socket in that device anyway this
can be simply removed (and device boots then no problem).
[juhosg:
- tweak subject line and description,
- remove #include "dev-usb.h",
- remove 'select ATH79_DEV_USB' from Kconfig]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37844
This patch fixes the code of the buttons for TP-Link WA901ND.
Signed-off-by: Rocco Folino <lordzen@autistici.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37696
Small router sold in EU: AR9330@400MHz, 1x USB2.0,
2x ethernet, 8MB flash, 32MB ram, one led, one button.
See: http://galeria.tech-blog.pl/TP-Link_TL-WR710N-EU/
[juhosg: use a separate kernel patch]
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3873/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37572
Looks like trunk@37090 has changed the logic that determines
if router's button was pressed. This resulted in TEW632BRP
always booting into failsafe mode because it detected pressed
button (which was not pressed).
Measure with voltmeter has shown that buttons on this router
are actually active-low. This patch reflects this fact in
board configuration and fixes 'load info failsafe mode' issue.
Note: it looks like Trendnet TEW632BRP and a close relative
to TEW-652BRP V1.0 and D-Link DIR-615C1, so same problem may
exist on those routers as well. This patch doesn't affect
routers other than 632BRP and unfortunately I do not have
hardware to test this issue with other routers.
This patch fixes#13893 and is tested on actuall Trendnet
TEW632BRP.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37569
