Commit Graph

442 Commits

Author SHA1 Message Date
Adrian Schmutzler
16af6535fa ipq40xx: switch to kernel 5.10
There have been enough tests and new developments require the new
kernel, so let's update it.

There is a bunch of devices that do not build anymore due to
kernel size limitations. These are disabled in a subsequent commit.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-11-03 23:50:56 +01:00
Davide Fioravanti
2cb24b3f3c ipq40xx: add support for Netgear SRR60/SRS60 and RBR50/RBS50
The Netgear SRS60 and SRR60 (sold together as SRK60) are two almost
identical AC3000 routers. The SRR60 has one port labeled as wan while
the SRS60 not. The RBR50 and RBS50 (sold together as RBK50) have a
different external shape but they have an USB 2.0 port on the back.

This patch has been tested only on SRS60 and RBR50, but should work
on SRR60 and RBS50.

Hardware
--------
SoC:   Qualcomm IPQ4019 (717 MHz, 4 cores 4 threads)
RAM:   512MB DDR3
FLASH: 4GB EMMC
ETH:
  - 3x 10/100/1000 Mbps Ethernet
  - 1x 10/100/1000 Mbps Ethernet (WAN)
WIFI:
  - 2.4GHz: 1x IPQ4019 (2x2:2)
  - 5GHz:   1x IPQ4019 (2x2:2)
  - 5GHz:   1x QCA9984 (4x4:4)
  - 6 internal antennas
BTN:
  - 1x Reset button
  - 1x Sync button
  - 1x ON/OFF button
LEDS:
  - 8 leds controlled by TLC59208F (they can be switched on/off
    independendently but the color can by changed by GPIOs)
  - 1x Red led (Power)
  - 1x Green led (Power)
UART:
  - 115200-8-N-1

Everything works correctly.

Installation
------------
These routers have a dual partition system. However this firmware works
only on boot partition 1 and the OEM web interface will always flash on
the partition currently not booted.

The following steps will use the SRS60 firmware, but you have to chose
the right firmware for your router.

There are 2 ways to install Openwrt the first time:

1) Using NMRPflash
 1. Download nmrpflash (https://github.com/jclehner/nmrpflash)
 2. Put the openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img
	file in the same folder of the nmrpflash executable
 3. Connect your pc to the router using the port near the power button.
 4. Run "nmrpflash -i XXX -f openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img".
	Replace XXX with your network interface (can be identified by
	running "nmrpflash -L")
 5. Power on the router and wait for the flash to complete. After about
	a minute the router should boot directly to Openwrt. If nothing
	happens try to reboot the router. If you have problems flashing
	try to set "10.164.183.253" as your computer IP address

2) Without NMRPflash
The OEM web interface will always flash on the partition currently not
booted, so to flash OpenWrt for the first time you have to switch to
boot partition 2 and then flash the factory image directly from the OEM
web interface.

To switch on partition 2 you have to enable telnet first:
 1. Go to http://192.168.1.250/debug.htm and check "Enable Telnet".
 2. Connect through telent ("telnet 192.168.1.250") and login using
	admin/password.

	To read the current boot_part:
		artmtd -r boot_part

	To write the new boot_part:
		artmtd -w boot_part 02

	Then reboot the router and then check again the current booted
	partition

Now that you are on boot partition 2 you can flash the factory Openwrt
image directly from the OEM web interface.

Restore OEM Firmware
--------------------
 1. Download the stock firmware from official netgear support.
 2. Follow the nmrpflash procedure like above, using the official
	Netgear firmware (for example SRS60-V2.2.1.210.img)

        nmrpflash -i XXX -f SRS60-V2.2.1.210.img

Notes
-----
1) You can check and edit the boot partition in the Uboot shell using
	the UART connection.
	"boot_partition_show" shows the current boot partition
	"boot_partition_set 1" sets the current boot partition to 1

2) Router mac addresses:

   LAN XX:XX:XX:XX:XX:69
   WAN XX:XX:XX:XX:XX:6a
   WIFI 2G XX:XX:XX:XX:XX:69
   WIFI 5G XX:XX:XX:XX:XX:6b
   WIFI 5G (2nd) XX:XX:XX:XX:XX:6c

   LABEL XX:XX:XX:XX:XX:69

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[added 5.10 changes for 901-arm-boot-add-dts-files.patch, moved
sysupgrade mmc.sh to here and renamed it, various dtsi changes]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-01 00:56:51 +01:00
Davide Fioravanti
24efb49ff0 ipq40xx: enable CONFIG_CMDLINE_PARTITION and CONFIG_LEDS_TLC591XX
CONFIG_CMDLINE_PARTITION:
Some devices with mmc like the Netgear Orbi Pro SRS60 or Netgear Orbi
RBR50 needs to hardcode the partitions layout in the cmdline boot
correctly

CONFIG_LEDS_TLC591XX:
This is needed for the led driver found in the Netgear Orbi Pro SRS60

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Shang Jia <jiash416@gmail.com>
[added 5.10 config]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-01 00:56:51 +01:00
Pavel Kubelun
78be2741aa ipq40xx: fix sleep clock
It seems like sleep_clk was copied from ipq806x.
Fix ipq40xx sleep_clk to the value QSDK defines.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [5.4+5.10]
2021-11-01 00:56:51 +01:00
Christian Lamparter
fd717f54be ipq40xx: detangle ath10k-board-qca4019 from ath10k-firmware-qca4019*
Back in the day, the board-2.bin came with ath10k-firmware-qca4019.
This changed with
commit c3b2efaf24 ("linux-firmware: ath10k: add board firmware packages")
which placed the board-2.bin into a separate package: ath10k-board-qca4019.
This was great, because it addressed one of the caveat of the original
ipq-wifi package:
commit fa03d441e9 ("firmware: add custom IPQ wifi board definitions")

|  2. updating ath10k-firmware-qca4019 will also replace
|      the board-2.bin. For this cases the user needs to
|      manually reinstall the wifi-board package once the
|      ath10k-firmware-qca4019 is updated.

This could be extended further so that ipq-wifi packages
no longer use "install-override" and the various QCA4019
variants list the ath10k-board-qca4019 as a CONFLICT
package.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-30 16:32:59 +02:00
Matthew Hagan
e3c47ff90d kernel: 5.10: backport qca8k stability improvements
This is a backport of Ansuel Smith's "Multiple improvement to qca8k stability"
series. The QCA8337 switch is available on multiple platforms including
ipq806x, ath79 and bcm53xx.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-10-24 16:56:17 +02:00
Tan Zien
85a42fa9cb ipq40xx: MR33: Fix LP5562 LED driver probe
Add the reg and color property to each channel node. This update is
to accommodate the multicolor framework.

Refer to:
<https://lore.kernel.org/all/20200622185919.2131-9-dmurphy@ti.com>
<https://lore.kernel.org/all/20210818070209.1540451-1-michal.vokac@ysoft.com>

Signed-off-by: Tan Zien <nabsdh9@gmail.com>
[replaced links to lore, wrote something of a commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-23 18:50:25 +02:00
Szabolcs Hubai
81d694e30b ipq40xx: use zImage for GL.iNet GL-B1300, GL-S1300 to shrink below 4096k
In the "ipq40xx: switch to Kernel 5.10" discussion at GitHub,
Adrian noted [0] that these GL.iNet Conexa series devices,
GL-B1300 and GL-S1300 failed their image generation [1] as their gzipped
uImage kernel went above 4096k.

While notifying the vendor about this problem [2], I tested all U-Boot
releases from GL.iNet:
- they really fail to boot kernel above 4096k
- they don't support lzma: "Unimplemented compression type 3"
- but they boot zImage

Using zImage (xz compression) the kernel is 2909k which is
more than a megabyte away from the KERNEL_SIZE := 4096k limit.

The gzip compressed version would be 4116k.

[0]: https://github.com/openwrt/openwrt/pull/4620#issuecomment-932765776
[1]: commit 7b1fa276f5 ("ipq40xx: add testing support for kernel 5.10")
[2]: https://forum.gl-inet.com/t/ipq40xx-kernel-size-and-u-boot-v5-10-is-too-big-for-4-mb/17619

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2021-10-10 16:47:41 +02:00
Robert Marko
7b1fa276f5 ipq40xx: add testing support for kernel 5.10
Add kernel 5.10 as the testing kernel to ipq40xx to
get wider testing.

The following devices failed to build with buildbot settings and all
feeds installed (apparently due to kernel size):

 * cell-c rtl30vw
 * compex wpj428
 * devolo magic 2 next
 * engenius emr3500
 * glinet gl-b1300
 * glinet gl-s1300
 * qcom ap-dk01.1-c1
 * qcom ap-dk04.1-c1

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Nick Hainke <vincent@systemli.org> [ipq4019/fritzbox-7530
                                               ipq4019/fritzbox-4040
                                               ipq4019/sxtsq-5ac]
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ipq4029/gl-b1300]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq4019/map-ac2200]
[add tested-by and note about failed devices]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-25 19:28:54 +02:00
Robert Marko
f4fb63d2ab ipq40xx: 5.10: move AR40xx to MDIO drivers
MDIO drivers were moved into their own sub directory of networking drivers.
This has caused the AR40xx driver to probe before MDIO drivers and that wont
work as it depends on the MDIO bus to be up so it can be fetched.

Lets solve it by moving the AR40xx into MDIO folder so they get probed like
before.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
ccf214a408 ipq40xx: net: ethernet: edma: reject unsupported coalescing params
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.

This driver did not previously reject unsupported parameters.

This is a required ethtool op since kernel 5.7.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
603848cad8 ipq40xx: net: ethernet: edma: update of_get_phy_mode() for 5.10
In kernel v5.5 of_get_phy_mode had its API changed, so its now returning 0
or errors instead of phymode.

Phymode is now returning by passing a pointer to phy_interface_t where it
will be stored.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
80f007fdb2 ipq40xx: 5.10: add kernel config
Copy config from 5.4 and run "make kernel_oldconfig".

Select default ("N") for all new symbols.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[make commit message more explicit]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-25 19:28:54 +02:00
Robert Marko
e9559182b9 ipq40xx: 5.10: refresh patches to apply
Refresh the kernel patches on top of 5.10 so they apply.
Manually fixup the 705-net-add-qualcomm-ar40xx-phy.patch
to apply.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
fec22cfa59 ipq40xx: 5.10: replace patches with upstreamed versions
USB and SDHCI LDO DTS patches have been upstreamed into 5.12, so
replace the local versions with upstreamed ones.

Reorder, and clearly mark the kernel version.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
75a90f161e ipq40xx: 5.10: remove duplicate GPIO export patch
Its in the generic target already, so remove the duplicate
as it breaks compilation.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
9fe5516ee5 ipq40xx: 5.10: drop upstreamed patches
Drop patches that have been upstreamed in before 5.10.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
8f27ac5ec0 ipq40xx: 5.10: copy patches
Copy over the 5.4 kernel patches to 5.10 folder.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
John Audia
51c7e1d25f kernel: bump 5.4 to 5.4.144
Manually rebased:
  backport-5.4/370-netfilter-nf_flow_table-fix-offloaded-connection-tim.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

Signed-off-by: John Audia <graysky@archlinux.us>
2021-09-13 17:08:17 +02:00
Sven Eckelmann
c7e9335e4c ipq40xx: Fix board-2.bin package name for Plasma Cloud PA2200
The board data file for the Plasma Cloud PA2200 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device
package name resulted in a not correctly selected package for the device
specific board-2.bin. The wifi driver has therefore loaded the wrong
calibration information into the wifi chip.

Fixes: 4871fd2616 ("ipq40xx: add support for Plasma Cloud PA2200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-09-12 18:52:30 +02:00
Sven Eckelmann
d0ffc17535 ipq40xx: Fix board-2.bin package name for Plasma Cloud PA1200
The board data file for the Plasma Cloud PA1200 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device
package name resulted in a not correctly selected package for the device
specific board-2.bin. The wifi driver has therefore loaded the wrong
calibration information into the wifi chip.

Fixes: ea5bb6bbfe ("ipq40xx: add support for Plasma Cloud PA1200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-09-12 18:52:30 +02:00
Sven Eckelmann
14bd392a1c ipq40xx: Select correct board-2.bin for EnGenius EMR3500
The board data file for the EnGenius EMR3500 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong
calibration information will be loaded into the wifi chip.

Fixes: 3f61e5e1b9 ("ipq40xx: add support for EnGenius EMR3500")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-09-12 18:52:30 +02:00
Sven Eckelmann
d9f4a4280e ipq40xx: Select correct board-2.bin for EnGenius EMD1
The board data file for the EnGenius EMD1 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong
calibration information will be loaded into the wifi chip.

Fixes: 51f3035978 ("ipq40xx: add support for EnGenius EMD1")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-09-12 18:52:30 +02:00
Hauke Mehrtens
b9cc16a5e8 kernel: Set CONFIG_RCU_CPU_STALL_TIMEOUT=21
The default value for CONFIG_RCU_CPU_STALL_TIMEOUT was changed from 60
seconds to 21 seconds in 2012 in the upstream kernel. Some targets
already use 21 seconds.

This patch changes the default value in the generic configuration to 21
seconds and removes the target specific configuration options.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-09-09 20:24:12 +02:00
Rui Salvaterra
505b7a2d08 kernel: move two symbols to the generic kconfigs
CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them
to the generic kconfigs. And resort the generic kconfigs while at it.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-08-29 17:07:19 +02:00
Stijn Tintel
a43da1be43 ipq40xx: fix Edgecore ECW5211 boot
The bootloader will look for a configuration section named ap.dk01.1-c2
in the FIT image. If this doesn't exist, the device won't boot.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-08-18 16:11:11 +03:00
David Bauer
4d81f08771 ipq40xx: ar40xx: reset port status register
This resolves incosnsitencies of the configured RX / TX flow control
modes between different boards or bootloaders.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-08-14 14:48:07 +02:00
David Bauer
685c790e9f ipq40xx: ar40xx: use FIELD_GET macro
This improves code readability.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-08-14 14:47:51 +02:00
David Bauer
b9162a9c85 ipq40xx: increase EX6150v2 SPI frequency
The chip supports clock speeds up to 50 MHz, however it won't even read
the chip-id correctly at this frequency.

45 MHz however works reliable.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-08-14 14:47:34 +02:00
Ansuel Smith
91a52f22a1 treewide: backport support for nvmem on non platform devices
In the current state, nvmem cells are only detected on platform device.
To quickly fix the problem, we register the affected problematic driver
with the of_platform but that is more an hack than a real solution.
Backport from net-next the required patch so that nvmem can work also
with non-platform devices and rework our current patch.
Drop the mediatek and dsa workaround and rework the ath10k patches.
Rework every driver that use the of_get_mac_address api.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-08-05 01:46:26 +02:00
Ansuel Smith
821b664099 ipq40xx: convert mtd-mac-address to nvmem implementation
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-07-19 14:51:22 +02:00
David Bauer
f9d1828105 ipq40xx: fix FRITZRepeater 1200 RGMII delay
When the AVM FRITZ!Repeater 1200 was introduced on Kernel 4.19, the
at803x PHY driver incorrectly set up the delays, not disabling delays
set by the bootloader.

The PHY was always operating with RX as well as TX delays enabled, but
with kernel 5.4 and later, the required TX delay is disabled, breaking
ethernet operation.

Correct the PHY mode, so the driver enables both delays.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-07-17 20:06:49 +02:00
Dmitry Tunin
88f39b72da ipq40xx: increase SPI frequency for Zyxel NBG6617
The mx25l25635f supports clock speed up to 50Mhz.

Also remove obsolete "mx25l25635f" hack and rename
the matching device-tree flash node.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[mention node rename as well. chip is very very likely
always the "f" revision for all NBG6617]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-07-11 01:38:52 +02:00
Adrian Schmutzler
cce8d16bf1 treewide: call check-size before append-metadata
sysupgrade metadata is not flashed to the device, so check-size
should be called _before_ adding metadata to the image.

While at it, do some obvious wrapping improvements.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-07-10 19:40:10 +02:00
Adrian Schmutzler
fac6096ad6 ipq40xx: add missing case closing symbol
Though not strictly necessary, add the closing symbol to make the
job easier for future developers editing this file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-28 01:06:08 +02:00
Rafał Miłecki
3342d574be ipq40xx: specify FritzBox 7530 LAN port label numbers
This helps managing LAN ports.

Ref: https://forum.openwrt.org/t/openwrt-21-02-0-second-release-candidate/98026/121
Fixes: 95b0c07a61 ("ipq40xx: add support for FritzBox 7530")
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-06-24 09:02:31 +02:00
Tomasz Maciej Nowak
1984a6bbca ipq40xx: add uboot-envtools to default packages
When support for Luma WRTQ-329ACN was added, the instructions for
flashing this device include using tools from uboot-envtools package.
Unfortunately the OpenWrt buildroot system omits packages from
DEVICE_PACKAGES when CONFIG_TARGET_MULTI_PROFILE,
CONFIG_TARGET_PER_DEVICE_ROOTFS, CONFIG_TARGET_ALL_PROFILES are set. In
result the official images are without tools mentioned in the
instruction. The workoround for the fashing would be installing
uboot-envtools when booted with initramfs image, but not always the
access to internet is available. The other method would be to issue the
necesary command in U-Boot environment but some serial terminals default
configuration don't work well with pasting lines longer than 80 chars.
Therefore add uboot-envtools to default packages, which adds really
small flash footprint to rootfs, where increased size usually is not an
issue.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2021-06-06 00:26:13 +02:00
Adrian Schmutzler
6f648ed7e6 treewide: remove "+" sign for increment with macaddr_add
Many people appear to use an unneeded "+" prefix for the increment
when calculating a MAC address with macaddr_add. Since this is not
required and used inconsistently [*], just remove it.

[*] As a funny side-fact, copy-pasting has led to almost all
    hotplug.d files using the "+", while nearly all of the
    02_network files are not using it.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-05 23:54:37 +02:00
Robert Marko
b126d9c3a3 ipq40xx: add netgear wac510 support
This adds support for the Netgear WAC510 Insight Managed Smart Cloud
Wireless Access Point, an indoor dual-band, dual-radio 802.11ac
business-class wireless AP with integrated omnidirectional antennae
and two 10/100/1000 Mbps Ethernet ports.

For more information see:
<https://www.netgear.com/business/wifi/access-points/wac510>

Specifications:
SoC:        Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:        256 MiB
Flash1:     2 MiB Winbond W25Q16JV SPI-NOR
Flash2:     128 MiB Winbond W25N01GVZEIG SPI-NAND
Ethernet:   Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port,
            WAN port active IEEE 802.3af/at PoE in
Wireless1:  Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
Wireless2:  Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae
Input:      (Optional) Barrel 12 V 2.5 A Power, Reset button SW1
LEDs:       Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN
Serial:     Header J2
1 - 3.3 Volt (Do NOT connect!)
2 - TX
3 - RX
4 - Ground
WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter!
         The Serial settings are 115200-8-N-1.

Installation via Stock Web Interface:
BTW: The default factory console/web interface login user/password are
admin/password.

In the web interface navigating to Management - Maintenance - Upgrade -
'Firmware Upgrade' will show you what is currently installed e.g.:
Manage Firmware
Current Firmware Version: V5.0.10.2
Backup Firmware Version: V1.2.5.11
Under 'Upgrade Options' choose Local (alternatively SFTP would be
available) then click/select 'Browse File' on the right side, choose
openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar
and hit the Upgrade button below. After a minute or two your browser
should indicate completion printing 'Firmware update complete.' and
'Rebooting AP...'.

Note that OpenWrt will use the WAN PoE port as actual WAN port
defaulting to DHCP client but NOT allowing LuCI access, use LAN port
defaulting to 192.168.1.1/24 to access LuCI.

Installation via TFTP Requiring Serial U-Boot Access:
Connect to the device's serial port and hit any key to stop autoboot.
Upload and boot the initramfs based OpenWrt image as follows:
(IPQ40xx) # setenv serverip 192.168.1.1
(IPQ40xx) # setenv ipaddr 192.168.1.2
(IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb
(IPQ40xx) # bootm

Note: This only runs OpenWrt from RAM and has not installed anything
to flash as of yet. One may permanently install OpenWrt as follows:

Check the MTD device number of the active partition:
root@OpenWrt:/# dmesg | grep 'set to be root filesystem'
[    1.010084] mtd: device 9 (rootfs) set to be root filesystem
Upload the factory image ending with .ubi to /tmp (e.g. using scp or
tftp). Then flash the image as follows (substituting the 9 in mtd9
below with whatever number reported above):
root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi
And reboot.

Dual Image Configuration:
The default U-Boot boot command bootipq uses the U-Boot environment
variables primary/secondary to decide which image to boot. E.g.
primary=0, secondary=3800000 uses rootfs while primary=3800000,
secondary=0 uses rootfs_1.
Switching their values changes the active partition. E.g. from within
U-Boot:
(IPQ40xx) # setenv primary 0
(IPQ40xx) # setenv secondary 3800000
(IPQ40xx) # saveenv
Or from a OpenWrt userspace serial/SSH console:
fw_setenv primary 0
fw_setenv secondary 3800000
Note that if you install two copies of OpenWrt then each will have its
independent configuration not like when switching partitions on the
stock firmware.
BTW: The kernel log shows which boot partition is active:
[    2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB)
vs.
[    2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB)
Note: After 3 failed boot attempts it automatically switches partition.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[squashed netgear-tar commit into main and rename netgear-tar for
now, until it is made generic.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-06-05 23:29:46 +02:00
Baptiste Jonglez
979f406366 ipq40xx: fix hard_config partition size on MikroTik hAP-ac2
The routerbootparts driver dynamically discovers the location of MikroTik
partitions, but it cannot determine their size (except by extending them
up to the start of the next discovered partition).

The hard_config partition has a default size of 0x1000 in the driver,
while it actually takes 0x2000 on the hAP-ac2.  Set the correct size in
the hAP-ac2 DTS.

On most devices, this isn't a problem as the actual data fits in 0x1000
bytes.  However, some devices have larger data that doesn't fit in 0x1000
bytes.  In any case, all devices seen so far have enough space for a
0x2000 hard_config partition before the start of the dtb_config partition.
With the current 0x1000 size:

0x00000000e000-0x00000000f000 : "hard_config"
0x000000010000-0x000000017bbc : "dtb_config"

With this patch extending the size to 0x2000:

0x00000000e000-0x000000010000 : "hard_config"
0x000000010000-0x000000017bbc : "dtb_config"

Other ipq40xx boards may need the same fix but it needs testing.

References: https://forum.openwrt.org/t/support-for-mikrotik-hap-ac2/23333/324
Acked-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
2021-05-08 12:18:43 +02:00
John Audia
0d2873df15 kernel: bump 5.4 to 5.4.114
Manually rebased*
  generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch

Added new backport*
  generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch

All others updated automatically.

The new backport was included based on this[1] upstream commit that will be
mainlined soon.  This change is needed because Eric Dumazet's check for
NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use
napi_gro_frags().

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

*Credit to Alexander Lobakin
1. https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=7ad18ff6449cbd6beb26b53128ddf56d2685aa93

Signed-off-by: John Audia <graysky@archlinux.us>
2021-04-30 23:48:37 +02:00
Roger Pueyo Centelles
d1f1e5269e ipq40xx: add support for MikroTik SXTsq 5 ac
This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD),
an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet
port.

Specifications:
 - SoC: Qualcomm Atheros IPQ4018
 - RAM: 256 MB
 - Storage: 16 MB NOR
 - Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae
 - Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in
 - 1x Ethernet LED (green)
 - 7x user-controllable LEDs
  · 1x power (blue)
  · 1x user (green)
  · 5x rssi (green)

Note:
 Serial UART is probably available on the board, but it has not been
 tested.

Flashing:
 Boot via TFTP the initramfs image. Then, upload a sysupgrade image
 via SSH and flash it normally. More info at the "Common procedures
 for MikroTik products" page https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2021-04-29 10:55:07 +02:00
Rui Salvaterra
3326b5e75c treewide: switch the timer frequency to 100 Hz
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-04-21 10:31:10 +01:00
Rui Salvaterra
27b5bae2ec treewide: remove redundant ubifs kconfig symbols
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-04-21 10:31:07 +01:00
Robert Marko
faea7becaf
ipq40xx: add MikroTik hAP ac2 support
This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC
(hAP ac²), a  indoor dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional antennae, USB port and  five
10/100/1000 Mbps Ethernet ports.

See https://mikrotik.com/product/hap_ac2 for more info.

Specifications:
 - SoC: Qualcomm Atheros IPQ4018
 - RAM: 128 MB
 - Storage: 16 MB NOR
 - Wireless:
   · Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
   · Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
 - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port,
             passive PoE in
- 1x USB Type A port

Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-04-05 04:13:28 +02:00
Aleksander Jan Bajkowski
12e942b1fd kernel: move some disabled symbols to generic
Move some disabled symbols found in armvirt target to generic.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2021-03-19 00:59:22 +01:00
Daniel Golle
9690836344 ipq40xx: work-around borked QCA SDK bootloader
The bootloader of many ipq40xx boards seems to require the config node
of the FIT image to be 'config@1' (or a secific different value).
This requirement used to be implicitely satisfied because OpenWrt used
to also call the configuration node inside a FIT image 'config@1'.
However, as recent U-Boot now prohibits the use of the '@' symbol as
part of node names, this was changed by
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Explicitely restore the default name of the configuration node to
'config@1' on ipq40xx.

Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-06 19:05:53 +00:00
Adrian Schmutzler
85b1f4d8ca treewide: remove execute bit and shebang from board.d files
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.

Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.

Note:

This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-06 11:30:06 +01:00
Robert Marko
7f2d9ccd09 ipq40xx: net: phy: qca807x: fix GPIO driver
While rebasing into setting bits instead of magic values,
I accidentally forgot to actually set the force bit.

Without it using the pins as GPIO-s did not actually work.

Fixes: b5c93ed ("ipq40xx: add Qualcomm QCA807x driver")

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-03-05 00:28:35 +01:00
Jason A. Donenfeld
196f3d586f kernel-5.4: bump to 5.4.102 and refresh patches
5.4.102 backported a lot of stuff that our WireGuard backport already
did, in addition to other patches we had, so those patches were
removed from that part of the series. In the process other patches were
refreshed or reworked to account for upstream changes.

This commit involved `update_kernel.sh -v -u 5.4`.

Cc: John Audia <graysky@archlinux.us>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
2021-03-04 22:06:53 +01:00
Paul Spooren
6ab33103af treewide: remove redundant KERNEL_PREFIX definitions
The variables KERNEL_INITRAMFS_PREFIX and KERNEL_PREFIX are already
defined in include/image.mk and don't have to be redefined in the
target Makefiles.

Signed-off-by: Paul Spooren <mail@aparcar.org>
[also cover imx6]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-23 00:26:40 +01:00
Adrian Schmutzler
5697915a18 ipq40xx: remove generic profile
On a platform with many very different devices, like found on ipq40xx,
the generic profile seems like a remnant of the past that does not
have a real use anymore.

Remove it to have one thing less to maintain.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-01-27 21:31:20 +01:00
Adrian Schmutzler
f52081bcf9 treewide: provide global default for SUPPORTED_DEVICES
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:

  SUPPORTED_DEVICES := $(subst _,$(comma),$(1))

At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:

  device/image name:  vendor_model
  compatible:         vendor,model

The equal redundant definitions are a symptom of this process.

Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.

This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-23 12:45:21 +01:00
Robert Marko
36347d003a ipq40xx: fix boards being shown twice
Since generic images have been split to their own
Makefile boards are showing up twice in menuconfig
as $(eval $(call BuildImage)) was not dropped from
the new generic.mk.

Hence $(eval $(call BuildImage)) was being called
twice.

So, lets simply drop it from generic.mk.

Fixes: 378c7ff282 ("ipq40xx: split generic images into own file")

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-01-21 17:08:16 +01:00
Robert Marko
f4fdd8609c
ipq40xx: mikrotik: enable MikroTik platform driver
This enables the MikroTik platform driver, it enables us to parse
valuable info from hard_config including WLAN calibration data
extraction from sysfs.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-01-17 14:31:56 +01:00
Robert Marko
0184889088 ipq40xx: mikrotik: enable MikroTik NOR parser
Needed for SPI-NOR based MikroTik IPQ40xx devices like hAP ac2.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-01-17 14:23:05 +01:00
Robert Marko
30a92f55de ipq40xx: mikrotik: enable CONFIG_MTD_ROUTERBOOT_PARTS
This enables the new MikroTik specific partition parser.

This avoids manually specifying the MikroTik specific partitions as they
can be detected by their magic values.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-01-17 14:23:05 +01:00
Robert Marko
b779da27ef ipq40xx: add MikroTik subtarget
MikroTik devices require the use of raw vmlinux out of the self
extracting compressed kernels.

They also require 4K sectors, kernel2minor, partition parser as well as
RouterBoard platform drivers.

So in order to not add unnecessary code to the generic sub target lets
introduce a MikroTik sub target.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-01-17 14:23:05 +01:00
John Thomson
10d057f84a ipq40xx: kernel compressed boot: reset watchdog countdown
If the watchdog is enabled, set the timeout to 30 seconds before
decompress is started.

Mikrotik ipq40xx devices running with RouterBoot have the SoC watchdog
enabled and running with a timeout that does not allow time for the
kernel to decompress and manage the watchdog.

On ipq40xx RouterBoot TFTP boot the watchdog countdown is reset before:
Jumping to kernel

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
2021-01-17 14:23:05 +01:00
Robert Marko
b6461e4654 ipq40xx: arm: compressed: add appended DTB section
This adds a appended_dtb section to the ARM decompressor
linker script.

This allows using the existing ARM zImage appended DTB support for
appending a DTB to the raw ELF kernel.

Its size is set to 1MB max to match the zImage appended DTB size limit.

To use it to pass the DTB to the kernel, objcopy is used:

objcopy --set-section-flags=.appended_dtb=alloc,contents \
	--update-section=.appended_dtb=<target>.dtb vmlinux

This is based off the following patch:
c063e27e02

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-01-17 14:23:05 +01:00
Alexander Couzens
378c7ff282
ipq40xx: split generic images into own file
In preparation of the new mikrotik subtarget split the generic images
into generic.mk

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2021-01-17 07:16:23 +01:00
Jan Alexander
6738b5e2ac uboot-envtools: add support for Aruba AP-303 and AP-365
Both devices use u-boot env variables to boot OpenWrt from its flash
partition. Using u-boot envtools, it is possible to change the bootcmd
back to the stock firmware partition directly from OpenWrt without
attaching a serial cable or even physically accessing the device.

Signed-off-by: Jan Alexander <jan@nalx.net>
2021-01-14 01:04:02 +01:00
Sungbo Eo
aad3d9c710 ipq40xx: remove unnecessary execute permission bit
DTS files do not need to be executable. 644 is enough.

Fixes: 0fbdb51f76 ("ipq40xx: add Edgecore OAP-100 support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[split by targets]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-03 15:48:18 +01:00
Adrian Schmutzler
9b1b89229f kernel: bump 5.4 to 5.4.86
Removed upstreamed patches:
  pending-5.4/499-mtd-parser-cmdline-Fix-parsing-of-part-names-with-co.patch

Manually merged:
  pending-5.4/611-netfilter_match_bypass_default_table.patch
  layerscape/302-dts-0112-arm64-dts-fsl-ls1028a-prepare-dts-for-overlay.patch

Build-tested: ipq806x/R7800, bcm27xx/bcm2711, ath79/{generic,tiny},
              ipq40xx, octeon, ramips/mt7621, realtek, x86/64
Run-tested: ipq806x/R7800, realtek

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: John Audia <graysky@archlinux.us>
Tested-by: Stijn Segers <foss@volatilesystems.org>
2021-01-01 17:07:28 +01:00
David Bauer
f3e45c45cb ipq40xx: remove non-existent ethernet PHY
Since updating the MDIO driver, the probe will fail hard on any
PHY not present on the bus, while this was not the case prior.

Fixes commit 26b1f72381 ("ipq40xx: net: phy: ar40xx: remove PHY
handling")
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-12-30 23:41:03 +01:00
Dongming Han
b9389186b0 ipq40xx: add support for GL.iNet GL-AP1300
Specifications:
SOC:        Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:        256 MiB
FLASH1:     4 MiB NOR
FLASH2:     128 MiB NAND
ETH:        Qualcomm QCA8075
WLAN1:      Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2:      Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT:      Reset
LED:        Power, Internet
UART1:      On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
OTHER:      On board with BLE module - by cp210x USB serial chip
            On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed

Install via uboot tftp or uboot web failsafe.

By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi
(IPQ40xx) # run lf

By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1

Afterwards upgrade can use sysupgrade image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
2020-12-25 10:38:13 +01:00
Robert Marko
fd033364f6 ipq40xx: net: ethernet: edma: use generic PHY print
Lets use the generic upstream phy_print_status() instead of doing 
something similar by hand.

Before:
ess_edma c080000.edma: eth1: GMAC Link is up with phy_speed=1000

After:
ess_edma c080000.edma eth1: Link is Up - 1Gbps/Full - flow control rx/tx

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Robert Marko
9d69505194 ipq40xx: net: ethernet: edma: use generic ksettings functions
Since we now have a proper PHY driver for QCA807x and AR803x has already
been supported properly there is no need for the driver to be poking
on PHY registers for ethtool ops.

So, lets simply use the generic
phy_ethtool_ksettings_get/phy_ethtool_ksettings_set functions.

This also has the advantage of properly populating stuff other than
speeds like, transceiver type, MDI-X etc.

ethtool before:
root@OpenWrt:/# ethtool eth1
Settings for eth1:
        Supported ports: [ TP MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
                                1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
                                1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  10baseT/Half 10baseT/Full
                                             100baseT/Half 100baseT/Full
                                             1000baseT/Full
        Link partner advertised pause frame use: No
        Link partner advertised auto-negotiation: No
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 4
        Transceiver: internal
        Auto-negotiation: on
        MDI-X: Unknown
        Supports Wake-on: d
        Wake-on: d
        Current message level: 0x00000000 (0)

        Link detected: yes

ethtool after:
root@OpenWrt:/# ethtool eth1
Settings for eth1:
        Supported ports: [ TP MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
                                1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
                                1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  10baseT/Half 10baseT/Full
                                             100baseT/Half 100baseT/Full
                                             1000baseT/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 4
        Transceiver: external
        Auto-negotiation: on
        MDI-X: off (auto)
        Supports Wake-on: d
        Wake-on: d
        Current message level: 0x00000000 (0)

        Link detected: yes

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Robert Marko
2a5bfb6600 ipq40xx: dts: convert PHY GPIO bindings
Since the new PHY driver manages each PHY individually and therefore 
registers each PHY that is marked with gpio-controller; DT property as a
GPIO controller we need to convert old DT bindings to account for this.

Only 2 boards use this so its not much of an issue.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Robert Marko
c8af7ea205 ipq40xx: dts: add QCA807x properties
This adds necessary DT properties for QCA807x PHY-s to IPQ4019 DTSI.

Also adds the PSGMII PHY as it wont get probed otherwise.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Robert Marko
053c3d8e0b ipq40xx: net: ethernet: edma: fix link detection
PHY needs to be soft reset before starting it from ethernet driver as
AR40xx calibration will leave it in unwanted state.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Robert Marko
26b1f72381 ipq40xx: net: phy: ar40xx: remove PHY handling
Since we now have proper PHY driver for the QCA807x PHY-s, lets remove
PHY handling from AR40xx.

This removes PHY driver, PHY GPIO driver and PHY init code.
AR40xx still needs to handle PSGMII calibration as that requires R/W
from the switch, so I am unable to move it into PHY driver.

This also converted the AR40xx driver to use OF_MDIO to find the MDIO
bus as it now cant be set through the PHY driver.
So lets depend on OF_MDIO in KConfig.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Robert Marko
b5c93edd74 ipq40xx: add Qualcomm QCA807x driver
This adds driver for the Qualcomm QCA8072 and QCA8075 PHY-s.

They are 2 or 5 port IEEE 802.3 clause 22 compliant
10BASE-Te, 100BASE-TX and 1000BASE-T PHY-s.

They feature 2 SerDes, one for PSGMII or QSGMII connection with MAC,
while second one is SGMII for connection to MAC or fiber.

Both models have a combo port that supports 1000BASE-X and 100BASE-FX
fiber.

Each PHY inside of QCA807x series has 2 digitally controlled output only
pins that natively drive LED-s.
But some vendors used these to driver generic LED-s controlled by
user space, so lets enable registering each PHY as GPIO controller and
add driver for it.

This also adds the ability to specify DT properties so that 1000 Base-T
LED will also be lit up for 100 and 10 Base connections.

This is usually done by U-boot, but boards running mainline U-boot are
not configuring this yet.

These PHY-s are commonly used in Qualcomm IPQ40xx, IPQ60xx and IPQ807x
boards.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Robert Marko
03bae3cafd ipq40xx: edma: convert to of_mdio_find_bus()
With the reworked MDIO driver, EDMA will fail to get the MII BUS as it
used the MII BUS stored inside the MDIO structure private data.

This obviously does not work with the modernized driver, so lets switch
to using a purpose build of_mdio_find_bus() which will return the MII
BUS and only requires the MDIO node to be passed.
This is easy as we already have the node parsed.

Also, since we now require OF_MDIO add that as dependency.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Robert Marko
4cdc8d20fa ipq40xx: backport upstream MDIO driver
IPQ40xx MDIO driver was upstreamed in kernel version 5.8.
So lets backport the upstream version and drop our local one.

This also refreshed the kernel config since the symbol name has changed.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Robert Marko
49795690e6 ipq40xx: refresh kernel config
Generic kernel config changed a lot, so lets refresh ipq40xx
to reduce the diff.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Stefan Schake
d3c8881194 ipq40xx: add support for devolo Magic 2 WiFi next
SOC:     IPQ4018 / QCA Dakota
CPU:     Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7
DRAM:    256 MiB
NOR:     32 MiB
ETH:     Qualcomm Atheros QCA8075 (2 ports)
PLC:     MaxLinear G.hn 88LX5152
WLAN1:   Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:   Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:   RESET, WiFi, PLC Button
LEDS:    red/white home, white WiFi

To modify a retail device to run OpenWRT firmware:
1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT
   initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'.
2) Power on the device while pressing the recessed reset button next to
   the Ethernet ports. This causes the bootloader to retrieve and start
   the initramfs.
3) Once the initramfs is booted, the device will come up with IP
   192.168.1.1. You can then connect through SSH (allow some time for
   the first connection).
4) On the device shell, run 'fw_printenv' to show the U-boot environment.
   Backup this information since it contains device unique factory data.
5) Change the boot command to support booting OpenWRT:
   # fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm'
6) Change directory to /tmp, download the sysupgrade (e.g. through wget)
   and install it with sysupgrade. The device will reboot into OpenWRT.

Notice that there is currently no support for booting the G.hn chip.
This requires userland software we lack the rights to share right now.

Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
2020-12-22 20:55:40 +01:00
Marek Lindner
4871fd2616 ipq40xx: add support for Plasma Cloud PA2200
Device specifications:

* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 36-64)
  - QCA9888 hw2.0 (PCI)
  - requires special BDF in QCA9888/hw2.0/board-2.bin
    bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 100-165)
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200
* GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE
* GPIO-LEDs for power (orange) and status (blue)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio3:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + used as LAN interface
  - phy@mdio4:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 802.3at POE+
    + used as WAN interface
* 12V 2A DC

Flashing instructions:

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-22 19:11:50 +01:00
Marek Lindner
ea5bb6bbfe ipq40xx: add support for Plasma Cloud PA1200
Device specifications:

* QCA IPQ4018
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200
* 2T2R 5 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200
* 3x GPIO-LEDs for status (cyan, purple, yellow)
* 1x GPIO-button (reset)
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio4:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + used as LAN interface
  - phy@mdio3:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 802.3af/at POE(+)
    + used as WAN interface
* 12V/24V 1A DC

Flashing instructions:

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-22 19:11:50 +01:00
Sven Eckelmann
8a891bfaa0 ipq40xx: Change name for openmesh.sh to vendor-free name
Other vendors are using functionality similar to the ones OpenMesh used to
implement two areas on the flash to store the default image and a fallback
image. So just change the name to dualboot_datachk.sh to avoid duplicated
code just to have the same script for different vendors.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-22 19:11:50 +01:00
Aleksander Jan Bajkowski
77575d4c02 kernel: move some disabled symbols to generic
Move some disabled config options found in lantiq target to generic.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-12-22 19:11:50 +01:00
Moritz Warning
debbc0a8a8 ipq40xx: use upper case for NETGEAR in DEVICE_VENDOR
Adjust spelling of vendor name to what is used in other places.

Also move definition in shared section.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-12-19 19:42:00 +01:00
John Audia
afd4bf08bc kernel: bump 5.4 to 5.4.83
Manually merged:
  layerscape/808-i2c-0011-i2c-imx-support-slave-mode-for-imx-I2C-driver.patch
  layerscape/808-i2c-0012-i2c-imx-correct-code-of-errata-A-010650-for-layersca.patch

Remaining modifications made by update_kernel.sh

Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711, x86/64 [*],
              ramips/mt7621 [*], ath79/tiny [*], ipq40xx [*], octeon [*],
              realtek [*]
Run-tested: ipq806x/R7800, ramips/mt7621 [*], octeon [*], realtek [*]

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
2020-12-15 12:05:26 +01:00
David Bauer
cdc8d4b46f ipq40xx: revert usage of VLAN S-TAG
This reverts the usage of the S-Tag for separating LAN and WAN port on
the embedded switch. Many users complained about not being able to
manage C-Tag addition / removal on the switch as well as degraded
performance.

Fixes: commit 9da2b56760 ("ipq40xx: fix ethernet vlan double tagging")

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-12-14 01:13:30 +01:00
Yushi Nishida
5e9a5c15ba ipq40xx: fix 5Ghz tx/rx power on the ASUS MAP-AC2200
The ASUS MAP-AC2200 suffers from a lower transmit/receive
signal power as compared to the stock firmware.

Upon investigation, it was discovered that stock firmware from
the GPL_MAP-AC2200_3.0.0.4.384.46249-g97d05bb.tar archive.
set the following GPIOs in "release/src/router/rc/init.c".

GPIO 44 and 46 have to be set to output high
GPIO 45 and 47 have to be set to output low

Here are some results, after activating the relevant
gpios through cmdline:

<https://forum.openwrt.org/t/asus-map-ac2200-low-transmit-receive-signal-5ghz/69005/12>

THX @ slh

Fixes: 9ad3967f14 ("ipq40xx: add support for ASUS Lyra")
Signed-off-by: Yushi Nishida <kyro2man@gmx.net>
[slightly rewritten commit, added missing <>)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-12-13 16:12:45 +01:00
Sven Eckelmann
8231994d3f ipq40xx: DTS style updates for OpenMesh devices
The OpenMesh related files were not updated since a while and the new
coding style requirements weren't integrated. This can cause problems
for new devices when an author uses these files as starting point.

* use SPDX-License-Identifiers instead of full license texts
* drop linux,default-trigger with value default-off for LEDs
* led nodes with label "abc:xyz" should have name "xyz_abc"
* led DT labels for "xyz_abc" should be "led_xyz_abc"
* "m25p80@0" flash node should be renamed to "flash@0"
* drop unnecessary empty lines

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[minor commit title and message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-23 13:44:47 +01:00
John Audia
667f6c7f49 kernel: bump 5.4 to 5.4.77
Manually rebased patches:
 bcm27xx/patches-5.4/950-0135-spi-spi-bcm2835-Disable-forced-software-CS.patch
 generic-backport/744-v5.5-net-sfp-soft-status-and-control-support.patch
 layerscape/patches-5.4/819-uart-0005-tty-serial-fsl_lpuart-enable-dma-mode-for-imx8qxp.patch
 mvebu/patches-5.4/521-arm64-dts-marvell-espressobin-Add-ethernet-switch-al.patch

Removed:
 layerscape/patches-5.4/819-uart-0012-tty-serial-lpuart-add-LS1028A-support.patch

All modifications made by update_kernel.sh

Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711,
              lantiq/Easybox 904 xDSL, x86_64
Run-tested: ipq806x/R7800, lantiq/Easybox 904 xDSL, x86_64

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-18 21:13:46 +01:00
Adrian Schmutzler
95b0751d0f ipq40xx: do not remove pci@40000000 for ap.dk04.1
This pci@40000000 node from upstream was dropped when the device
was converted from local DTS(I) files to kernel patches in [1] to
ensure that change was purely cosmetic.

However, the DK04.1 has a PCI-E slot by default, so let's keep
(i.e. not remove) the kernel definition now.

[1] c4beac9ea2 ("ipq40xx: use upstream DTS files for IPQ4019/AP-DK04.1")

Suggested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-13 18:34:41 +01:00
Robert Marko
4f277b4da5 ipq40xx: 5.4: update and reorder patches
A lot of patches are outdated versions of upstreamed patches and
drivers.

So lets pull in the upstreamed patches and reorder remaining ones.

This drops the unnecessary 721-dts-ipq4019-add-ethernet-essedma-node.patch
which adds nodes for not yet in OpenWrt IPQESS driver.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[do not touch 902-dts-ipq4019-ap-dk04.1.patch here]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-13 16:08:58 +01:00
David Bauer
e73d866c6f ipq40xx: enable RX hash / CTAG TX offloading for single-phy
This re-enables offloading features disabled by
commit 9da2b56760 ("ipq40xx: fix ethernet vlan double tagging").

Single-PHY devices use port-based VLANs on the switch, therefore no
S-TAG magic is involved here. Re-enabling these features restores
throughput back to 950 Mbit/s.

Reported-by: Jannis Pinter <jannis@pinterjann.is>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-11-01 15:30:22 +01:00
Adrian Schmutzler
a7afeb3142 ipq40xx: remove support for kernel 4.19
The target uses 5.4 as default kernel since 03/2020.

Kernel 4.19 support is not really maintained anymore, it does not
seem to be needed, and removing it will make upcoming driver
updates easier. Thus, remove it.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-19 15:30:44 +02:00
John Audia
0efec6a008 kernel: bump 5.4 to 5.4.71
All modifications made by update_kernel.sh

Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711,
              lantiq/Easybox 904 xDSL
Run-tested:   ipq806x/R7800, lantiq/Easybox 904 xDSL

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
[add lantiq test reports]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-15 17:46:54 +02:00
Rui Salvaterra
e788e9bd87 treewide: enable the vDSO
The vDSO is used to accelerate some syscalls. It should work fine wherever it's
available, so enable it globally for all targets.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2020-10-13 20:08:41 +02:00
Robert Marko
9604e216bf ipq40xx: 5.4: move AR40xx driver into files
There is no point in keeping the AR40xx driver as a patch as its
not pending merge or backport.

To allow for easier maintenance until DSA is ready move it into
files like EDMA is.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[combine with removal from patches-5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-09 14:21:10 +02:00
Adrian Schmutzler
c4beac9ea2 ipq40xx: use upstream DTS files for IPQ4019/AP-DK04.1
Upstream provides DTS(I) files for IPQ4019/AP-DK04.1, but we overwrite
them with local versions so far.

Remove the local files and use patches to be closer to upstream.
We already do the same for IPQ40xx/AP-DK01.1-C1.

Technically, this changes the compatible from "qcom,ipq4019" to
"qcom,ipq4019-dk04.1-c1", but it has never been implemented correctly
beforehand anyway.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-07 22:26:52 +02:00
Sungbo Eo
8f29e36963 ipq40xx: improve support for Edgecore ECW5211
This adds several stylistic and functional improvements of the recently
added Edgecore ECW5211, especially:

* Drop the local BDFs as those are already in the upstream under different names
* Add SPDX tag to DTS
* Add label MAC address
* Move LED trigger to DTS
* Remove unnecessary status="okay"
* Disable unused SS USB phy as the USB port only supports USB 2.0
* Make uboot-env partition writable
* Remove qcom,poll_required_dynamic property as the driver does not use it
* Tidy up the device recipe

Fixes: 4488b260a0 ("ipq40xx: add Edgecore ECW5211 support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Acked-by: Robert Marko <robert.marko@sartura.hr>
2020-10-07 18:07:54 +02:00
Adrian Schmutzler
ad90a42e48 ipq40xx: remove model name from LED labels
Like in the previous patches for ath79 and ramips, this will remove
the "devicename" from LED labels in ipq40xx.

The devicename is removed in DTS files and 01_leds, and a migration
script is added. While at it, also harmonize capitalization of
wlan2G/wlan5G vs. wlan2g/wlan5g.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-07 01:31:37 +02:00
Sungbo Eo
4682d4d770 ipq40xx: tidy up device recipe for Edgecore OAP100
* split up DEVICE_TITLE into DEVICE_{VENDOR,MODEL}
* use SOC instead of DEVICE_DTS

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-09-26 18:26:19 +02:00
Adrian Schmutzler
bdd9dd8ab2 ipq40xx: tidy up dts-v1 statements
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.

Therefore, adding it to a DTS _and_ a DTSI file is actually wrong,
as it will be present twice then (though the compiler does not
complain about it).

In ipq40xx, the dts-v1 statement is already included in
qcom-ipq4019.dtsi, so we don't have to add it anywhere at all.
However, based on the conditions stated above, this requires
qcom-ipq4019.dtsi to be included as the first file in any DTS(I).

Consequently, this patch removes all cases of dts-v1 for the
ipq40xx target, and moves the includes accordingly where necessary.

While at it, remove a few obviously unneeded includes on the way.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-25 21:10:41 +02:00
Christian Lamparter
fa1713e791 ipq40xx: fix DTS warning in qcom-ipq4029-gl-s1300.dts
.dts:226.17-230.4: Warning (spi_bus_reg): /soc/spi@78b6000/spi@1:
	SPI bus unit address format error, expected "0"

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00