The MediaTek's Crypto Engine module is only available for mt7623, in
which case it is built into the kernel.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 3f2d0703b6)
Fix the wps button to prevent wrongly detected recovery procedures.
In the official banana pi r64 git the wps button is set to
GPIO_ACTIVE_LOW and not GPIO_ACTIVE_HIGH.
Import patch to fix on boot unwanted recovery entering:
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- failsafe button wps was pressed -
- failsafe -
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry-picked from commit 6686194255)
The kernel configuration option CONFIG_MACH_MT7629 selects
CONFIG_HAVE_ARM_ARCH_TIMER now. Handle this change in the config-5.10.
This fixes some build problems.
Fixes: 81530d69ef ("kernel: bump 5.10 to 5.10.121")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
93e3fce916c6 mt76: pass original queue id from __mt76_tx_queue_skb to the driver
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 06d0cc2fb3)
c07f45927839 firmware: update mt7622 firmware to version 20220630
af406a2d1c36 mt76: do not use skb_set_queue_mapping for internal purposes
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 8e90abb396)
At least two AX820 hardware variants are known to exist, but they cannot
be distinguished (same hardware revision, no specific markings).
They appear to have the same LED hardware, but wired differently:
- One has a red system LED at GPIO 15, a green wlan2g LED at GPIO 14 and
a blue wlan5g LED at GPIO 16;
- The other only offers a green system LED at GPIO 15, with GPIO 14 and
16 being apparently not connected
Finally, a Yuncore datasheet says the canonical wiring should be:
- Blue wlan2g GPIO 14, green system GPIO 15, red wlan5g GPIO 16
All GPIOs are tied to a single RGB LED which is exposed via lightpipe on
the device front casing.
Considering the above, this patch exposes all three LEDs, preserves the
common system LED (GPIO 15) as the openwrt status LED, and removes the
color information from the LEDs names since it is not consistent across
hardware. The LED naming is made consistent with other YunCore devices.
A note is added in DTS to ensure this information is always available
and prevent unwanted changes in the future.
Fixes: #10131 "YunCore AX820: GPIO LED not correct"
Reviewed-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
No patches rebased, just checksum update for this refresh.
Build system: x86_64
Build-tested: ipq806x/R7800
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit c5882c33a7)
Enable PowerPC Book-E Watchdog Timer support. Having this enabled
in-kernel will result in procd starting it during boot.
This effectively solves the problem of the WDT in the Winbond W83793 chip
potentially resetting the system during sysupgrade, which could result
in an unbootable device. While the driver is modular, resulting in procd
not starting the WDT during boot (because that happens before kmod
load), the WDT handover during sysupgrade results in the WDT being
started. This normally shouldn't be a problem, but the W83793 WDT does
not like procd's defaults, nor the handover happening during sysupgrade.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 04071cb111)
Avoid shipping ath10k board file in Mikrotik initram images
Most will only ever need to use these initram images once—to initially
load OpenWrt, but fix these images for more consistent Wi-Fi performance
between the initram and installed squashfs images.
OpenWrt BUILDBOT config ignores -cut packages in the initram images build.
This results in BUILDBOT initram images including the linux-firmware
qca4019 board-2.bin, and (initram image booted) Mikrotik devices loading
a generic BDF, rather than the intended BDF data loaded
from NOR as an api 1 board_file.
buildbot snapshot booted as initram image:
cat /etc/openwrt_version
r19679-810eac8c7f
dmesg | grep ath10k | grep -E board\|BDF
[ 9.794556] ath10k_ahb a000000.wifi: Loading BDF type 0
[ 9.807192] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:16
crc32 11892f9b
[ 12.457105] ath10k_ahb a800000.wifi: Loading BDF type 0
[ 12.464945] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:17
crc32 11892f9b
CC: Robert Marko <robimarko@gmail.com>
Fixes: 5eee67a72f ("ipq40xx: mikrotik: dont include ath10k-board-qca4019 by default")
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 602b5f6c60)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Since MikroTik subtarget now uses dynamic BDF loading its crucial that it
doesnt include the board-2.bin at all which is provided by the
ath10k-board-qca4019 package.
So to resolve this dont include the ath10k-board-qca4019 package on the
MikroTik subtarget.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 5eee67a72f)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Since we now provide the BDF-s for MikroTik IPQ40xx devices on the fly,
there is noneed to include package and ship them like we do now.
This also resolves the performance issues that happen as MikroTik
changes the boards and ships them under the same revision but they
actually ship with and require a different BDF.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit ab141a6e2c)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Since we now can pass the API 1 BDF-s aka board.bin to the ath10k
driver per radio lets use that to provide the BDF-s for MikroTik devices.
This also resolves the performance issues that happen as MikroTik changes
the boards and ships them under the same revision but they actually ship
with and require a different BDF.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4d4462cc2a)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Some ath10k IPQ40xx devices like the MikroTik hAP ac2 and ac3 require the
BDF-s to be extracted from the device storage instead of shipping packaged
API 2 BDF-s.
This is required as MikroTik has started shipping boards that require BDF-s
to be updated, as otherwise their WLAN performance really suffers.
This is however impossible as the devices that require this are release under
the same revision and its not possible to differentiate them from devices
using the older BDF-s.
In OpenWrt we are extracting the calibration data during runtime and we are
able to extract the BDF-s in the same manner, however we cannot package the
BDF-s to API 2 format on the fly and can only use API 1 to provide BDF-s on
the fly.
This is an issue as the ath10k driver explicitly looks only for the board.bin
file and not for something like board-bus-device.bin like it does for pre-cal
data.
Due to this we have no way of providing correct BDF-s on the fly, so lets
extend the ath10k driver to first look for BDF-s in the board-bus-device.bin
format, for example: board-ahb-a800000.wifi.bin
If that fails, look for the default board file name as defined previously.
So, backport the upstream ath10k patch.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3daf2d477e)
[prune unrelated patch refreshes]
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Update ath10k-ct to the latest version which includes the backported
ath10k commit for requesting API 1 BDF-s with a unique name like caldata.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit ab97b2a25d)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
11f5c7b fw4.uc: fix zone helper assignment
b9d35ff fw4.uc: don't skip zone for unavailable helper
e35e26b tests: add test for zone helpers
a063317 ruleset: fix conntrack helpers
e1cb763 ruleset: reuse zone-jump.uc template for notrack and helper chain jumps
11410b8 ruleset: reorder declarations & output tweaks
880dd31 fw4: fix skipping invalid IPv6 ipset entries
5994466 fw4: simplify `is_loopback_dev()`
53886e5 fw4: fix crash in parse_cthelper() if no helpers are present
11256ff fw4: add support for configurable includes
3b5a033 tests: add test coverage for firewall includes
d79911c fw4: support sets with timeout capability but without default expiry
15c3831 fw4: add support for `option log` in rule and redirect sections
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit e8433fb433)
The random crashes observed with HARDENED_USERCOPY enabled no longer
seem to occur. Enable HARDENED_USERCOPY to improve security.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 61587c9242)
We do not need support for 32 bit applications, as we're building
everything for 64 bit.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 3e1848ee0f)
This patch provides support for the Firebox M300 reset button.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit 19231cf838)
This patch provides support for the Firebox M300 only user-controllable
bi-color LED, and makes the green "shield" LED act as the typical
OpenWrt status led.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit 4ab421b81d)
The MikroTik mAP-2nd (sold as mAP) is an indoor 2.4Ghz AP with
802.3af/at PoE input and passive PoE passthrough.
See https://mikrotik.com/product/RBmAP2nD for more details.
Specifications:
- SoC: QCA9533
- RAM: 64MB
- Storage: 16MB NOR
- Wireless: QCA9533 802.11b/g/n 2x2
- Ethernet: 2x 10/100 ports,
802.3af/at PoE in port 1, 500 mA passive PoE out on port 2
- 7 user-controllable LEDs
Note: the device is a tiny AP and does not distinguish between both
ethernet ports roles, so they are both assigned to lan.
With the current setup, ETH1 is connected to eth1 and ETH2 is connected
to eth0 via the embedded switch port 2.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. The "ETH1" port
must be used to upload the TFTP image. Follow common MikroTik procedure
as in https://openwrt.org/toh/mikrotik/common.
Tested-By: Andrew Powers-Holmes <aholmes@omnom.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit e1223dbee3)
Linux MTD requires the parent partition be writable for a child
partition to be allowed write permission.
In order for soft_config to be writeable (and modifiable via sysfs),
the parent RouterBoot partition must be writeable
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit bb929a0f9c)
Linux MTD requires the parent partition be writable for a child
partition to be allowed write permission.
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
(cherry picked from commit 86fb287ad5)
Update this pending patch to remove the untested (variable eraseregions)
section, alongside simplifying the patch.
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[refresh and split out unrelated refreshes]
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit 4f7065ed25)
This adds the igc driver for the Intel 2.5GBit Ethernet chip to the
default packages.
Fixes: #10064
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit aae3a8a254)
OpenWrt now uses firewall4 (nft) by default,
so iptables should also default to nftables backend.
When multiple packages provide the same virtual package,
opkg pick the first one by alphabetical order,
so we rename iptables-legacy to iptables-zz-legacy and add
iptables-legacy in PROVIDES.
We also need to remove IPTABLES_NFTABLES config as
this cause recursive dependencies.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
(cherry picked from commit 35fec487e3)
Kernel 5.10.124 introduced a new symbol 'LIB_MEMNEQ'. Add it to the
generic 5.10 config.
Fixes: 9e5d743422 ("kernel: bump 5.10 to 5.10.124")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit f3caba679b)
This requires U-Boot environment changes:
setenv OpenWrt_kernel watchguard_firebox-m300-fit-uImage.itb
setenv loadaddr 0x20000000
setenv wgBootSysA 'setenv bootargs root=/dev/mmcblk0p2 rw rootdelay=2 console=$consoledev,$baudrate fsl_dpaa_fman.fsl_fm_max_frm=1530; mmc dev 0; ext2load mmc 0:1 $loadaddr $OpenWrt_kernel; bootm $loadaddr'
Trying to sysupgrade an image containing this change on an M300 already
running OpenWrt will fail with the following error:
Tue Jun 14 12:06:21 EEST 2022 upgrade: The device is supported, but the config is incompatible to the new image (1.0->1.1). Please upgrade without keeping config (sysupgrade -n).
Tue Jun 14 12:06:21 EEST 2022 upgrade: Kernel switched to FIT uImage. Update U-Boot environment.
Tue Jun 14 12:06:21 EEST 2022 upgrade: Reading partition table from bootdisk...
Tue Jun 14 12:06:21 EEST 2022 upgrade: Extract boot sector from the image
Tue Jun 14 12:06:21 EEST 2022 upgrade: Reading partition table from image...
Image check failed.
This is to prevent rendering your device unbootable. Make the U-Boot
environment changes as instruced above, and then flash the image using
sysupgrade -F. The config can be kept, there is no need to use -n.
After the new image booted successfully, you can increase the compat_version:
uci set system.@system[0].compat_version='1.1'
uci commit
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit c4b499bc03)
Use the KERNEL_SUFFIX variable in Build/sdcard-img, rather than
using hardcoded "-kernel.bin", to allow overriding KERNEL_SUFFIX for a
device.
Fixes: 080a769b4d ("qoriq: new target")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 86948716db)
No patches required a rebase, just updated checksum.
Build system: x86_64
Build-tested: ipq806x/R7800
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 5202a511cc)
WolfSSL is crashing with an illegal opcode in some x86_64 CPUs that have
AES instructions but lack other extensions that are used by WolfSSL
when AES-NI is enabled.
Disable the option by default for now until the issue is properly fixed.
People can enable them in a custom build if they are sure it will work
for them.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 0bd5367233)
Restore CONFIG_I8K + CONFIG_INTEL_INT0002_VGPIO that got
removed when I refreshed the config. Each x86 target gets
its own CONFIG_CRYPTO_BLAKE2S + LIB settings as only the
x86_64 can use the accelerated x86 version.
Also remove two extra spaces that sneaked into geode's config.
Fixes: 539e60539a ("generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 9fc2d58bf8)
This is now built-in, enable so it won't propagate on target configs.
Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 539e60539a)
This updates prereq-build.mk to find a suitable realpath utility, and
adds another place to look for a suitable getopt utility.
realpath has been used most notably by scripts/ipkg-build since
commit bb95be9265 ("scripts,ipkg-build: use realpath for pkg_dir")
and there are assorted other uses of it during a build.
It is ordinarily provided by GNU coreutils. This adds a SetupHostCommand
to locate it either under its own name or under grealpath, the name that
it will be available as under MacPorts or Homebrew, which use
--program-prefix=g.
Similarly, update the SetupHostCommand for getopt to be able to locate a
util-linux getopt at the default path used by MacPorts, in the same
fashion that
commit cc16f5d73e ("build: try to find getopt in macOS homebrew's standard location")'
did for Homebrew. As there is no standard alternative --program-prefix
for util-linux utilities in the way that GNU packages often use a "g"
prefix, this path-based approach is required in case a non-util-linux
getopt (such as one provided by an OS) shadows the util-linux getopt
in the PATH.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
(cherry picked from commit f614332197)
This adds a few fixes for compiling against Linux 5.10:
1. segment_eq() has been removed with upstream commit
428e2976a5bf7e7f5554286d7a5a33b8147b106a ("uaccess: remove
segment_eq") and can use uaccess_kernel() instead
2. ioremap_nocache() is removed and is now an alias for ioremap() with
upstream commit 4bdc0d676a643140bdf17dbf7eafedee3d496a3c ("remove
ioremap_nocache and devm_ioremap_nocache")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
(cherry picked from commit cd3de51bb4)
Existing conntracks will continue to be SNATed to 192.0.0.1 even after
464xlat interface gets teared down. To prevent this, matching
conntracks must be killed.
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
(cherry picked from commit 289c46869b)
There is not RTC battery connected to the SoC of the UniFi 6 LR board.
Disable the RTC to prevent the system coming up with time set to
2000-01-01 00:00:00 after each reboot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 692d87a27b)
Some K2P comes with the worse boards with GD25Q128 (may be A2), which
only works with 50MHz frequency and less. Reduce spi frequency so that
these routers can boot.
remove m25p,fast-read because it isn't needed for 50MHz SPI.
Signed-off-by: Aviana Cruz <gwencroft@proton.me>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 857ea3f690)
902b321 wireless-regdb: Update regulatory rules for Israel (IL)
20f6f34 wireless-regdb: add missing spaces for US S1G rules
25652b6 wireless-regdb: Update regulatory rules for Australia (AU)
081873f wireless-regdb: update regulatory database based on preceding changes
166fbdd wireless-regdb: add db files missing from previous commit
e3f03f9 Regulatory update for 6 GHz operation in Canada (CA)
888da5f Regulatory update for 6 GHz operation in United States (US)
647bcaa Regulatory update for 6 GHz operation in FI
c6b079d wireless-regdb: update regulatory rules for Bulgaria (BG) on 6GHz
2ed39be wireless-regdb: Remove AUTO-BW from 6 GHz rules
7a6ad1a wireless-regdb: Unify 6 GHz rules for EU contries
68a8f2f wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit e3e9eb31a2)
With some OS (Guix) the git submodule command is wrapped in
a script. Current logic parse the git submodule script directly.
If it's wrapped the prereq check wrongly fails while 'git submodule
--recursive' is actually available.
Add an additional check that try to directly use the 'git submodule'
command to check if the prereq is satisfied.
Fixes: #9986
Reported-by: Attila Lendvai <attila@lendvai.name>
Suggested-by: Attila Lendvai <attila@lendvai.name>
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
(cherry picked from commit ab1f3a8706)
This reverts the airtime scheduler back from the virtual-time based scheduler
to the deficit round robin scheduler implementation.
This reduces burstiness and improves fairness by improving interaction with AQL.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 6d49a25804)
