This patch fixes the ath79-nand build error:
|Package kmod-tpm is missing dependencies for the following libraries:
|rng-core.ko
by making it depend on rng-core from 4.19 onwards.
This should work as 4.9 is gone so only 4.14 and 4.19
are there.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This adds the dm-raid kmod, which is needed for
LVM builtin raid configurations, aka "MD-over-LVM"
Signed-off-by: Chris Koying Browet <cbro@semperpax.com>
bnx2x driver support for the x86 architecture. Includes module and
firmware for Broadcom QLogic 5771x/578xx 10/20-Gigabit ethernet
adapters.
Signed-off-by: Petko Bordjukov <bordjukov@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added +kmod-lib-zlib-inflate as well]
After commit e82a4d9cfb ("config: regenerate *_shipped sources") the mconf
parser became more strict as a side effect and started to spew a series of
warnings when evaluating our generated kconfig sources:
tmp/.config-package.in:705:warning: ignoring unsupported character '@'
The root cause of these warnings is a wrong use of the @SYMBOL dependency
syntax in various Makefile. Fix the corresponding Makefiles by turning
`@SYM||@SYM2` expressions into the proper `@(SYM||SYM2)` form.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
While testing 4.19 build on malta/be64, I've encountered following
error:
gpio-button-hotplug/gpio-button-hotplug.c:529:18: error: implicit
declaration of function 'gpio_to_desc'
which is caused by the missing include fixed by this patch.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Supports EIP97 and EIP197 found on Armada 37xx, 7k and 8k SoCs.
Unfortunately firmware for EIP197 is not easily obtainable, therefore
to not cause lot of user requests directed at OpenWrt, package it as
module with explanation where to obtain the firmware.
Cc: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This improves FullMAC firmware compatibility, adds logging in case of
firmware crash and *may* fix "Invalid packet id" errors.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
FCC allows maximum antenna gain of 6 dBi. 15.247(b)(4):
> (4) The conducted output power limit
> specified in paragraph (b) of this section
> is based on the use of antennas
> with directional gains that do not exceed
> 6 dBi. Except as shown in paragraph
> (c) of this section, if transmitting
> antennas of directional gain greater
> than 6 dBi are used, the conducted
> output power from the intentional radiator
> shall be reduced below the stated
> values in paragraphs (b)(1), (b)(2),
> and (b)(3) of this section, as appropriate,
> by the amount in dB that the
> directional gain of the antenna exceeds
> 6 dBi.
https://www.gpo.gov/fdsys/pkg/CFR-2013-title47-vol1/pdf/CFR-2013-title47-vol1-sec15-247.pdf
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Most of the txpower for the ath10k firmware is stored as twicepower (0.5 dB
steps). This isn't the case for max_antenna_gain - which is still expected
by the firmware as dB.
The firmware is converting it from dB to the internal (twicepower)
representation when it calculates the limits of a channel. This can be seen
in tpc_stats when configuring "12" as max_antenna_gain. Instead of the
expected 12 (6 dB), the tpc_stats shows 24 (12 dB).
Tested on QCA9888 and IPQ4019 with firmware 10.4-3.5.3-00057.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
FCC allows maximum antenna gain of 6 dBi. 15.247(b)(4):
> (4) The conducted output power limit
> specified in paragraph (b) of this section
> is based on the use of antennas
> with directional gains that do not exceed
> 6 dBi. Except as shown in paragraph
> (c) of this section, if transmitting
> antennas of directional gain greater
> than 6 dBi are used, the conducted
> output power from the intentional radiator
> shall be reduced below the stated
> values in paragraphs (b)(1), (b)(2),
> and (b)(3) of this section, as appropriate,
> by the amount in dB that the
> directional gain of the antenna exceeds
> 6 dBi.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Changes:
ath10k: Improve PMF/MPF mgt frame check
And add a driver for 5.2 (beta, not even tested yet) kernel.
Refresh patches.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Add support for xfrm interfaces in kernel. XFRM interfaces are used by
the IPsec stack for tunneling.
XFRM interfaces are available since linux 4.19.
Signed-off-by: André Valentin <avalentin@marcant.net>
Commit afc056d7dc ("gpio-button-hotplug: support interrupt
properties") changed the gpio-keys interrupt handling logic in a way,
that it always misses first event, which causes issues with rc.button
scripts, so this patch restores the previous behaviour.
Fixes: afc056d7dc ("gpio-button-hotplug: support interrupt properties")
Reported-by: Kristian Evensen <kristian.evensen@gmail.com>
Tested-by: Kuan-Yi Li <kyli.tw@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [drop state check]
Currently the generated event contains wrong seen value, when the button
is pressed for the first time:
rmmod gpio_button_hotplug; modprobe gpio_button_hotplug
[ pressing the wps key immediately after modprobe ]
gpio-keys: create event, name=wps, seen=1088, pressed=1
So this patch adds a check for this corner case and makes seen=0 if the
button is pressed for the first time.
Tested-by: Kuan-Yi Li <kyli.tw@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
ctinfo is a new tc filter action module. It is designed to restore
information contained in firewall conntrack marks to other packet fields
and is typically used on packet ingress paths. At present it has two
independent sub-functions or operating modes, DSCP restoration mode &
skb mark restoration mode.
The DSCP restore mode:
This mode copies DSCP values that have been placed in the firewall
conntrack mark back into the IPv4/v6 diffserv fields of relevant
packets.
The DSCP restoration is intended for use and has been found useful for
restoring ingress classifications based on egress classifications across
links that bleach or otherwise change DSCP, typically home ISP Internet
links. Restoring DSCP on ingress on the WAN link allows qdiscs such as
but by no means limited to CAKE to shape inbound packets according to
policies that are easier to set & mark on egress.
Ingress classification is traditionally a challenging task since
iptables rules haven't yet run and tc filter/eBPF programs are pre-NAT
lookups, hence are unable to see internal IPv4 addresses as used on the
typical home masquerading gateway. Thus marking the connection in some
manner on egress for later restoration of classification on ingress is
easier to implement.
Parameters related to DSCP restore mode:
dscpmask - a 32 bit mask of 6 contiguous bits and indicate bits of the
conntrack mark field contain the DSCP value to be restored.
statemask - a 32 bit mask of (usually) 1 bit length, outside the area
specified by dscpmask. This represents a conditional operation flag
whereby the DSCP is only restored if the flag is set. This is useful to
implement a 'one shot' iptables based classification where the
'complicated' iptables rules are only run once to classify the
connection on initial (egress) packet and subsequent packets are all
marked/restored with the same DSCP. A mask of zero disables the
conditional behaviour ie. the conntrack mark DSCP bits are always
restored to the ip diffserv field (assuming the conntrack entry is found
& the skb is an ipv4/ipv6 type)
e.g. dscpmask 0xfc000000 statemask 0x01000000
|----0xFC----conntrack mark----000000---|
| Bits 31-26 | bit 25 | bit24 |~~~ Bit 0|
| DSCP | unused | flag |unused |
|-----------------------0x01---000000---|
| |
| |
---| Conditional flag
v only restore if set
|-ip diffserv-|
| 6 bits |
|-------------|
The skb mark restore mode (cpmark):
This mode copies the firewall conntrack mark to the skb's mark field.
It is completely the functional equivalent of the existing act_connmark
action with the additional feature of being able to apply a mask to the
restored value.
Parameters related to skb mark restore mode:
mask - a 32 bit mask applied to the firewall conntrack mark to mask out
bits unwanted for restoration. This can be useful where the conntrack
mark is being used for different purposes by different applications. If
not specified and by default the whole mark field is copied (i.e.
default mask of 0xffffffff)
e.g. mask 0x00ffffff to mask out the top 8 bits being used by the
aforementioned DSCP restore mode.
|----0x00----conntrack mark----ffffff---|
| Bits 31-24 | |
| DSCP & flag| some value here |
|---------------------------------------|
|
|
v
|------------skb mark-------------------|
| | |
| zeroed | |
|---------------------------------------|
Overall parameters:
zone - conntrack zone
control - action related control (reclassify | pipe | drop | continue |
ok | goto chain <CHAIN_INDEX>)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make suitable adjustments for backporting to 4.14 & 4.19
and add to SCHED_MODULES_FILTER
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This adds a new package for the kernel module of the ATUSB WPAN driver.
Signed-off-by: Sebastian Meiling <s@mlng.net>
[fixed SoB: and From: mismatch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This reverts commit 7c50182e0c.
Produces build error:
Package kmod-sched is missing dependencies for the following libraries:
nf_conntrack.ko
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
ctinfo is a new tc filter action module. It is designed to restore
information contained in firewall conntrack marks to other packet fields
and is typically used on packet ingress paths. At present it has two
independent sub-functions or operating modes, DSCP restoration mode &
skb mark restoration mode.
The DSCP restore mode:
This mode copies DSCP values that have been placed in the firewall
conntrack mark back into the IPv4/v6 diffserv fields of relevant
packets.
The DSCP restoration is intended for use and has been found useful for
restoring ingress classifications based on egress classifications across
links that bleach or otherwise change DSCP, typically home ISP Internet
links. Restoring DSCP on ingress on the WAN link allows qdiscs such as
but by no means limited to CAKE to shape inbound packets according to
policies that are easier to set & mark on egress.
Ingress classification is traditionally a challenging task since
iptables rules haven't yet run and tc filter/eBPF programs are pre-NAT
lookups, hence are unable to see internal IPv4 addresses as used on the
typical home masquerading gateway. Thus marking the connection in some
manner on egress for later restoration of classification on ingress is
easier to implement.
Parameters related to DSCP restore mode:
dscpmask - a 32 bit mask of 6 contiguous bits and indicate bits of the
conntrack mark field contain the DSCP value to be restored.
statemask - a 32 bit mask of (usually) 1 bit length, outside the area
specified by dscpmask. This represents a conditional operation flag
whereby the DSCP is only restored if the flag is set. This is useful to
implement a 'one shot' iptables based classification where the
'complicated' iptables rules are only run once to classify the
connection on initial (egress) packet and subsequent packets are all
marked/restored with the same DSCP. A mask of zero disables the
conditional behaviour ie. the conntrack mark DSCP bits are always
restored to the ip diffserv field (assuming the conntrack entry is found
& the skb is an ipv4/ipv6 type)
e.g. dscpmask 0xfc000000 statemask 0x01000000
|----0xFC----conntrack mark----000000---|
| Bits 31-26 | bit 25 | bit24 |~~~ Bit 0|
| DSCP | unused | flag |unused |
|-----------------------0x01---000000---|
| |
| |
---| Conditional flag
v only restore if set
|-ip diffserv-|
| 6 bits |
|-------------|
The skb mark restore mode (cpmark):
This mode copies the firewall conntrack mark to the skb's mark field.
It is completely the functional equivalent of the existing act_connmark
action with the additional feature of being able to apply a mask to the
restored value.
Parameters related to skb mark restore mode:
mask - a 32 bit mask applied to the firewall conntrack mark to mask out
bits unwanted for restoration. This can be useful where the conntrack
mark is being used for different purposes by different applications. If
not specified and by default the whole mark field is copied (i.e.
default mask of 0xffffffff)
e.g. mask 0x00ffffff to mask out the top 8 bits being used by the
aforementioned DSCP restore mode.
|----0x00----conntrack mark----ffffff---|
| Bits 31-24 | |
| DSCP & flag| some value here |
|---------------------------------------|
|
|
v
|------------skb mark-------------------|
| | |
| zeroed | |
|---------------------------------------|
Overall parameters:
zone - conntrack zone
control - action related control (reclassify | pipe | drop | continue |
ok | goto chain <CHAIN_INDEX>)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make suitable adjustments for backporting to 4.14 & 4.19
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Upstream Linux's input gpio-keys driver supports
specifying a external interrupt for a gpio via the
'interrupts' properties as well as having support
for software debounce.
This patch ports these features to OpenWrt's event
version. Only the "pure" interrupt-driven support is
left behind, since this goes a bit against the "gpio"
in the "gpio-keys" and I don't have a real device to
test this with.
This patch also silences the generated warnings showing
up since 4.14 due to the 'constification' of the
struct gpio_keys_button *buttons variable in the
upstream struct gpio_keys_platform_data declaration.
gpio-button-hotplug.c: In function 'gpio_keys_get_devtree_pdata':
gpio-button-hotplug.c:392:10: warning: assignment discards 'const'
qualifier from pointer target type [-Wdiscarded-qualifiers]
button = &pdata->buttons[i++];
^
gpio-button-hotplug.c: In function 'gpio_keys_button_probe':
gpio-button-hotplug.c:537:12: warning: assignment discards 'const'
qualifier from pointer target type [-Wdiscarded-qualifiers]
bdata->b = &pdata->buttons[i];
^
gpio-button-hotplug.c: In function 'gpio_keys_probe':
gpio-button-hotplug.c:563:37: warning: initialization discards 'const'
qualifier from pointer target type [-Wdiscarded-qualifiers]
struct gpio_keys_button *button = &pdata->buttons[i];
^
Acked-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
For devices such as BTHOMEHUBV5A with both reset and restart buttons,
its easily accessible restart button has been assigned to KEY_POWER
power script to poweroff preventing accidental (or malicious) factory
resets by KEY_RESTART reset script. However an easily accessible button
immediately powering off the device is also undesirable.
As KEY_RESTART is already used for reset script (and there's no
KEY_REBOOT in Linux input events), use KEY_POWER2 for rebooting via new
reboot script with 5 second seen delay.
Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
For devices such as BTHOMEHUBV5A with both reset and restart buttons,
its easily accessible restart button has been assigned to KEY_POWER
power script to poweroff preventing accidental (or malicious) factory
resets by KEY_RESTART reset script. However an easily accessible button
immediately powering off the device is also undesirable.
As KEY_RESTART is already used for reset script (and there's no
KEY_REBOOT in Linux input events), use KEY_POWER2 for rebooting via new
reboot script with 5 second seen delay.
Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
This patch updates ath10k-ct to current version.
Changes are:
ath10k-ct: Fix printing PN in peer stats.
Previous logic was incorrect. Also add set-special API to enable
returning PN.
Patches refreshed and tested on 8devices Jalapeno dev board(IPQ4019)
Signed-off-by: Robert Marko <robimarko@gmail.com>
MT7620 integrated WMAC does not need RT2x00 PCI driver or firmware
Also corrected kmod-eeprom-93cx6 and kmod-lib-crc-itu-t dependencies
according to original Kconfig and lsmod output
This will remove some unnecessary packages from MT7620 target to
save some space
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[75 characters per line in the commit message]
No target is using kernel 3.18 anymore, remove all the generic
support for kernel 3.18.
The removed packages are depending on kernel 3.18 only and are not used on
any recent kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 4.1, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently Auto probing for BMP/BME280 does not work because kernel
module name in the call is not correct.
Package name was used instead of kernel module name.
Signed-off-by: Robert Marko <robimarko@gmail.com>
struct ieee80211_local needs to be passed in separately instead of
dereferencing the (potentially NULL) sdata
Signed-off-by: Felix Fietkau <nbd@nbd.name>
9cd701a4f028 ath10k-ct: Add PN get/set API for wave-2 firmware.
5c8a4668323b ath10k-ct: Support over-riding the power ctl table in eeprom
75e2705f31bb ath10k-ct: CCA, eeprom, other changes.
a696e602a0fc ath10k-ct: Attempt to fix-out-of-tree compile for 4.16
a2aec62262df ath10k: Improve beacon tx status for 4.20 kernel.
be5c21a82b15 ath10k-ct: Fix out-of-tree compile for 4.20, pull in stable changes for 4.19
Fixes compile errors when using the 4.20 flavour.
Also the amount of beacon errors seems to have dropped.
Tested on a Mikrotik RB912UAGS-5HPacD
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Currently the Geode builds fails on following kernel module missing
dependencies:
Package kmod-drm-amdgpu is missing dependencies for the following libraries:
backlight.ko
drm_kms_helper.ko
fb.ko
ttm.ko
So this patch tries to fix the kmod-drm-amdgpu module dependecies.
Fixes: 2f239c0 ("x86: video: add amdgpu DRM kernel package")
Fixes: 2f6918e ("x86: video: add radeon DRM module support")
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Both targets have their own idea of how to use ehci-fsl.
This patch reverts part of commit
68b8d3b079 ("kernel: usb: add FSL EHCI package") and moves
ehci-fsl back into kmod-usb2, while also making it hopefully
useable for the mpc85xx target.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Replace the patch introduced by commit d0b969eee8 ("mac80211: rt2x00:
do not increment sequence number while re-transmitting") was merged
into wireless-drivers.git. Replace our version with the merged version.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
After getting rid of cryptsetup's heavy openssl dependency, there is now
the problem of missing RIPEMD160 support. RIPEMD160 is used for True/Vera
crypt volumes as well as old LUKS1 ones.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The removed patches are now integrated in the upstream kernel.
Refresh all patches on top of the new backports release.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
New target introduces initial support for NVIDIA Tegra SoC based devices.
It focuses on Tegra 2 CPUs, for successors supporting NEON instruction
set the target should be split in two subtargets.
This initial commit doesn't create any device image, it's groundwork
for further additions.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
