Commit Graph

929 Commits

Author SHA1 Message Date
Gabor Juhos
eb9e3651dd ar71xx: add support for the MikroTik RB911-2Hn/5Hn boards
The patch adds support for the MikroTik RB911-2Hn (911 Lite2)
and the RB911-5Hn (911 Lite5) boards:

  https://mikrotik.com/product/RB911-2Hn
  https://mikrotik.com/product/RB911-5Hn

The two boards are using the same hardware design, the only difference
between the two is the supported wireless band.

Specifications:
  * SoC: Atheros AR9344 (600MHz)
  * RAM: 64MiB
  * Storage: 16 MiB SPI NOR flash
  * Ethernet: 1x100M (Passive PoE in)
  * Wireless: AR9344 built-in wireless MAC, single chain
              802.11b/g/n (911-2Hn) or 802.11a/g/n (911-5Hn)

Notes:
  * Older versions of these boards might be equipped with a NAND
    flash chip instead of the SPI NOR device. Those boards are not
    supported (yet).
  * The MikroTik RB911-5HnD (911 Lite5 Dual) board also uses the
    same hardware. Support for that can be added later with little
    effort probably.

Installation:

1. Setup a DHCP/BOOTP Server with the following parameters:
   * DHCP-Option 66 (TFTP server name): pointing to a local TFTP
     server within the same subnet of the DHCP range
   * DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
     of the to be booted image. The usable intramfs files are:
       - openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
       - openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
       - openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin

2. Press the reset button on the board and keep that pressed.

3. Connect the board to your local network via its ethernet port.

4. Release the button after the LEDs on the board are turned off.
   Now the board should load and start the initramfs image from
   the TFTP server.

5. Upload the sysupgrade image to the board with scp:
     $ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin

5. Log in to the running system listening on 192.168.1.1 via ssh
   as root (without password):
     $ ssh root@192.168.1.1

7. Flash the uploaded firmware file from the ssh session via the
   sysupgrade command:
     root@OpenWrt:~# sysupgrade /tmp/fw.bin

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-22 10:53:45 +01:00
Piotr Dymacz
030176e0e7 ar71xx: image: rework EnGenius ENS202EXT factory image
Current EnGenius ENS202EXT factory image recipe version causes factory
images of the following devices to be corrupted. This issue wasn't
visible until recent changes of image Makefile snippets order.

Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 13:39:54 +01:00
Roger Pueyo Centelles
e15c63a375 ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC)
This patch adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP
AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with
integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet
ports.

See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.

Specifications:
 - SoC: Qualcomm Atheros QCA9556
 - RAM: 64 MB
 - Storage: 16 MB NOR
 - Wireless:
   · Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
   · Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
 - Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port, passive
   PoE in

Working:
 - Board/system detection
 - Sysupgrade
 - Serial console
 - Ethernet
 - 2.4 GHz radio
 - 5 GHz radio
 - Reset button

Not working:
 - LEDs (added according to Mikrotik's GPL sources but not functional)

 Unsupported:
 - ZT2046Q SPI temperature and voltage sensor

Contributors: Giuseppe Tipaldi (@Ciusss89)
              Ricky (@rickydee)

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: whitespace fix, use PHYADDR instead of PHYMASK]
2018-01-15 04:14:18 +01:00
Piotr Dymacz
2e5252d346 ar71xx: add support for GL.iNet GL-AR750
GL.iNet GL-AR750 is a small size, dual-band (AC750) router, based on
Qualcomm/Atheros QCA9531 v2 + QCA9887. FCC ID: 2AFIW-AR750.

Specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 1x USB 2.0 (power controlled by GPIO)
- 1x microSD (GL857L)
- 3x LED (all driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- header for optional PoE module
- 1x micro USB for main power input
- UART + I2C header on PCB

Flash instruction:

Vendor firmware is based on OpenWrt/LEDE. GUI or sysupgrade can be used
to flash OpenWrt/LEDE firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Piotr Dymacz
6cf682e214 ar71xx: image: move Sitecom WLR-8100 from legacy to generic
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Davide Fioravanti
a85db951db ar71xx: fix Sitecom WLR-8100 support
This patch fixes Sitecom WLR-8100:

- mtd layout
- LAN and WAN MAC address setup
- 2.4 GHz Wi-Fi MAC address setup
- 5 GHz Wi-Fi support (calibration data, MAC address setup, missing
  ath10k-* packages)

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[squashed commits, fixed whitespace issues, reworded commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Piotr Dymacz
af8f0629df ar71xx: add support for ALFA Network R36A
ALFA Network R36A is a successor of the previous model, the R36 (Ralink
RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2.

Specification:

- 650/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB
- 1x USB 2.0 (power controlled by GPIO)
- 6x LED (5 of them are driven by GPIO)
- 2x button (reset, wifi/wps)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- DC jack for main power input (12 V)
- UART header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   device, wait for first blink of all LEDs (indicates network setup),
   then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Piotr Dymacz
1f06144cde ar71xx: add support for Teltonika RUT900
Teltonika RUT900 is an industrial 3G router based on Atheros AR9344.

There are available 3 other models in RUT9xx series: RUT905, RUT950 and
RUT955, which differ in availability of additional I/O ports, built-in
GSM modem type, GPS antenna and other features. FCC ID of the RUT950
model (LTE module built-in): 2AET4-RUT950.

This patch adds support for the RUT900 model only but can be easily
extended to cover whole series. Also, as there are several different
3/4G modules (Huawei, Quectel, Telit) used in whole series, packages
required for WWAN support are not included by default. It is up to the
user to install required software for built-in modem.

Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA
- built-in 3G module (example: Telit HE910-D)
- 2x miniSIM slot
- 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G)
- PCA9539 16-bit GPIO I2C expander
- 12x LED (4 are driven by AR9344, 7 by PCA9539)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- UART available on PCB edge connector

Serial console pinout:

- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side

Flash instruction:

Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1".

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:09:43 +01:00
Piotr Dymacz
4b0eebe9df ar71xx: add support for ALFA Network N5Q
ALFA Network N5Q is a successor of previous model, the N5 (outdoor
CPE/AP, based on Atheros AR7240 + AR9280). New version is based on
Atheros AR9344.

Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 5 GHz (AR9344), with ext. PA (RFPA5542) and LNA, up to 27 dBm
- 8x LED (7 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmare which is based
on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   device, wait for first blink of all LEDs (indicates network setup),
   then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 21:30:16 +01:00
Piotr Dymacz
7f9f42d42e ar71xx: add support for ALFA Network AP91-5G
ALFA Network AP91-5G is a 5 GHz outdoor AP/CPE board, based on Atheros
AR7240 + AR9280.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 32 MB of RAM (DDR1)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1T1R 5 GHz (AR9280), with ext. PA (SE5004L) and LNA, up to 27 dBm
- 6x LED (5 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART and LEDs headers on PCB

Flash instruction:

Use "factory" image in vendor GUI (in case of problems, make sure your
board has up to date firmware). Alternatively, TFTP in U-Boot can be
used: select option "2. Load system code then write to Flash via TFTP"
during early boot and use "sysupgrade" image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 20:33:18 +01:00
Matthias Schiffer
0cd5e85e7a
ar71xx: create new ar71xx/tiny subtarget for 4MB flash devices
This new subtarget sets the small_flash flag and removes unused kernel
configuration.

small_flash removes KERNEL_KALLSYMS, which saves ~107KB in the default
configuration; removing unneeded hardware support from ar71xx/tiny saves
another ~18KB (both after LZMA).

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-13 19:54:45 +01:00
Matthias Schiffer
29d126b5c1
ar71xx/generic: add generic- prefix to vendor-specific image Makefile snippets
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-13 19:54:45 +01:00
Roger Pueyo Centelles
82626cc145 ar71xx: add support for MikroTik RouterBOARD 921GS-5HPacD r2 (mANTBox 15s)
This patch adds support for the MikroTik RouterBOARD 921GS-5HPacD r2
(mANTBox 15s), an outdoor sector antenna with a built-in 802.11ac
wireless router. Additionally, it adds a new profile for devices with
>= 128 MB NAND flash and 802.11ac to the ar71xx/mikrotik subtarget.

See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info.

Specifications:
 - SoC: Qualcomm Atheros QCA9558 (720 MHz)
 - RAM: 128 MB
 - Storage: 128 MB NAND
 - Wireless: external QCA9822 802.11a/ac 2x2:2
 - Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in
 - SFP: 1x host

Working:
 - Board/system detection
 - NAND storage detection
 - Wireless
 - Ethernet
 - 1x user LED
 - Reset button
 - Sysupgrade

Untested:
 - SFP cage (probably not working)

Installation:
 - Boot initramfs image via TFTP and then flash sysupgrade image

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2017-12-21 17:06:54 +01:00
Henryk Heisig
85c1644a86 ar71xx: generate BR region-code factory image for TP-Link TL-WR940N
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-12-14 09:29:30 +01:00
Jonas Gorski
eeeee885fb ar71xx: fix lzma-loader build with glibc
For an unknown reason gcc tries to link in crti.o when building with a
glibc toolchain (this does not happen with other targets). Prevent this
by telling gcc explicitly to not do that.

Fixes the following build error:

/home/jonas/git/lede/staging_dir/toolchain-mips_24kc_gcc-5.5.0_glibc/lib/gcc/mips-openwrt-linux-gnu/5.5.0/../../../../mips-openwrt-linux-gnu/lib/crti.o: In function `_init':
(.init+0x18): relocation truncated to fit: R_MIPS_GOT16 against `__gmon_start__'
/home/jonas/git/lede/staging_dir/toolchain-mips_24kc_gcc-5.5.0_glibc/lib/gcc/mips-openwrt-linux-gnu/5.5.0/../../../../mips-openwrt-linux-gnu/lib/crti.o: In function `_init':
(.init+0x28): relocation truncated to fit: R_MIPS_CALL16 against `__gmon_start__'
collect2: error: ld returned 1 exit status

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-12-13 11:34:51 +01:00
Luis Araneda
575178e462 treewide: add only one device when appending to TARGET_DEVICES
This will avoid some conflicts when doing a git rebase or merge,
specially when adding support to a new device.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
[drop brcm47xx changes which rename the images]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-12 18:47:26 +01:00
Zoltan HERPAI
7b5c989ab9 merge: targets: update image generation and targets
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2017-12-08 19:41:18 +01:00
Tim Thorpe
673793d753 ar71xx: add support for TP-Link TL-WR1043N v5
TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4,
except that the USB port has been removed and there is no longer a
removable antenna option.

The software is more in line with the Archer series in that it uses a
nested bootloader scheme.

Specifications:

 - QCA9563 at 775 MHz
 - 64 MB RAM
 - 16 MB flash
 - 3 (non-detachable) Antennas / 450 Mbit
 - 1x/4x WAN/LAN Gbps Ethernet (QCA8337)
 - reset and Wi-Fi buttons

Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
2017-11-14 22:36:46 +01:00
Paul Wassi
e202a8b9f6 ar71xx: add support for TP-Link TL-WA901ND v5
The TL-WA901ND v5 has the same hardware as v4, although the PCB has
a different layout. Installation from factory is done via TFTP.
(rename -factory image to wa901ndv4_tp_recovery.bin for tftp)

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2017-11-14 22:36:46 +01:00
Robert Marko
ac4a52b5c8 ar71xx: complete support for RB mAP 2nD
This patch adds support for the MikroTik RouterBOARD mAP 2nD
https://mikrotik.com/product/RBmAP2nD

Specifications:

- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: builtin QCA9531, 2x2:2
- Ethernet: 2x100M (802.3af/at POE in and passive POE out on ETH2)
- USB: microUSB type AB port

This patch adds missing code to fully support mAP. Machfile already
contained configuration for mAP 2nD, but device specific configuration
like LEDs etc., was missing.

Note: The POE LED works but doesn't turn on when POE passthrough is
enabled, despite being configured with GPIO trigger.

Installation

1. Login to the Mikrotik WebUI to backup your licence keys
2. Setup a DHCP/BOOTP server with:
   - DHCP-Option 66 (TFTP server name) pointing to a local TFTP
     server within the same subnet of the DHCP range
   - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
     of the to be booted image
3. Connect the port labeled internet to your local network
4. Keep the reset button pushed down and power on the board

The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started LEDE via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.

Revert to RouterOS

Use the "rbcfg" package on in LEDE:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply

Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.

Click on install again.

In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-11-14 22:36:46 +01:00
Robert Marko
3b15eb06c3 ar71xx: complete support for RB wAP 2nD
This patch adds support for the MikroTik RouterBOARD wAP
https://mikrotik.com/product/RBwAP2nD

Specifications:

- SoC: Qualcomm QCA9533 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9533, 2x2:2
- Ethernet: 1x100M (802.3af/at POE in)

This patch adds missing code to fully support wAP. Machfile already
contained configuration for wAP 2nD but device specific configuration
like LEDs etc. was missing.

Installation:

1. Login to the Mikrotik WebUI to backup your licence keys
2. Setup a DHCP/BOOTP server with:
   - DHCP-Option 66 (TFTP server name) pointing to a local TFTP
     server within the same subnet of the DHCP range
   - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
     of the to be booted image
3. Connect the port labeled internet to your local network
4. Keep the reset button pushed down and power on the board

The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started LEDE via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.

Revert to RouterOS

Use the "rbcfg" package on in LEDE:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply

Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.

Click on install again.

In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-11-14 22:36:46 +01:00
Paul Wassi
b23b0fb28b ar71xx: add support for TP-Link TL-WR810N v2
TP-Link TL-WR810N v2 is a compact Wi-Fi router with two Ethernet ports.

Specification:

- QCA9533 (650 MHz)
- 32 MB RAM
- 8 MB Flash
- 300 Mbps Wi-Fi 2.4 GHz
- 2x 10/100 Mbps Ethernet (eth0, eth1)
- UART on testpads on PCB
- 1x LED (GPIO-controlled)
- 1x reset/WPS button
- 1x slide-switch with 2 GPIO inputs

Flash instructions:

- Flash as regular firmware update in Web UI
- Default: 192.168.0.254 / admin / admin
- Select *-factory.bin

When holding reset button during power-up, U-Boot requests a file
'wr810nv1_tp_recovery.bin' from TFTP server at 192.168.0.66

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2017-11-14 22:36:46 +01:00
Piotr Dymacz
c83bdd094e ar71xx: add support for Wallys DR342
Wallys DR342 is a 5 GHz, 2T2R AP/CPE board based on Atheros AR9342.

Short specification:

- 560/450/225 MHz (CPU/DDR/AHB)
- 1x Gbps Ethernet (AR8035) with passive PoE support (24-56 V)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 5 GHz with external FEM (SKY85728-11), up to 30 dBm
- 2x MMCX connectors
- miniPCIe connector with PCIe and USB 2.0 buses
- optional miniSIM slot
- 7x LED, 1x button
- UART, (E)JTAG and LED headers
- 1x DC jack for main power (12-56 V)

Flash instruction (do it under U-Boot, using UART):

1. tftp 0x82000000 lede-ar71xx-generic-dr342-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-11-14 22:36:46 +01:00
Piotr Dymacz
55c77b3d3c ar71xx: increase kernel partition size for TP-Link RE450 v1
This increases kernel partition size and fixes rootfs (file-system)
partition size on TP-Link RE450 v1. Also, while we are at it, switch
from statically defined kernel and rootfs partitions in kernel cmdline
to "tplink-fw" mtd splitter.

Fixes: FS#1072.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-11-14 22:36:46 +01:00
Piotr Dymacz
2eeb8ac271 ar71xx: image: fix typo in tp-link.mk
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-11-14 22:36:46 +01:00
Henryk Heisig
ca6002c0ef ar71xx: increase kernel partition size for some TP-Link boards
This patch increases kernel partition size and re-enables image
generation for below TP-Link boards:

- archer-c58-v1
- archer-c60-v1
- tl-wr902ac-v1
- tl-wr942n-v1

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[commit message and title reworded]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-11-14 22:36:46 +01:00
Henryk Heisig
34958c8269 ar71xx: Archer C58/C59/C60 fix qca9886 wireless interface
This commit fix 5GHz wireless interface used in Archer C58/C59/C60v1
and set correctly MAC address on this interface.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-10-26 14:44:08 +02:00
Julien Dusser
8d9ff6b6f7 ar71xx: lzma loader use LTO
Change the Makefile to use LTO for better code optimisations. Gains are
very low, only 270 bytes saved, but it's only Makefile changes.

Signed-off-by: Julien Dusser <julien.dusser@free.fr>
2017-10-24 13:24:04 +02:00
Julien Dusser
8c5702f2a0 ar71xx: fix lzma loader performance issues
Some bootloaders set a cache cohenrency to a very slow mode. Use code from
Linux kernel to set it to "Cacheable, noncoherent, write-back, write
allocate".

Perfomance impact is significant on TP-Link EAP245 board, kernel
decompression time fall from 33 seconds to less than 1.

Signed-off-by: Julien Dusser <julien.dusser@free.fr>
2017-10-24 13:24:04 +02:00
Hauke Mehrtens
f7a6fd3153 ar71xx: deactivate some boards with too small kernel partitions
This affects the following boards:
 * dr344
 * archer-c58-v1
 * archer-c60-v1
 * tl-wr902ac-v1
 * tl-wr942n-v1
 * ubnt-uap-pro
 * ubnt-unifi-outdoor-plus

The build fails for any of these boards because the resulting kernel
image will not fit into the kernel partition.

When CONFIG_KERNEL_KALLSYMS  is not set it could be that the kernel will
fit onto the board again, this is the case for release images.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-10-22 23:15:11 +02:00
Felix Fietkau
9887afb1af ar71xx: add support for TP-LINK Archer C7 v4
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9561+QCA9888.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin via Web interface

Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin
and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f040000 +$filesize
3. cp.b $fileaddr 0x9f040000 $filesize
4. reset

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-19 16:14:19 +02:00
Felix Fietkau
2c9aff289e ar71xx: add support for Nokia WI2A-AC200i
Specifications:
 - SoC: Qualcomm QCA9558 (720 MHz)
 - RAM: 256MB
 - Storage: 1MB NOR, 128 MB NAND flash
 - Ethernet: 1x1000M

Installation:
 1. Connect to serial console on the board
 2. Boot initramfs image over u-boot
 3. Copy image to the device and run sysupgrade

Installation without serial console is not supported at this time

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-19 12:27:42 +02:00
Robert Marko
443abb8ccd ar71xx: add support for Mikrotik RB750P-PBr2
Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in, 4 PoE out)
- Outdoor use ready

This ethernet router is based on the same platform as the hEX PoE lite.

Installation

1. login to the Mikrotik WebUI to backup your licence keys
2. setup a DHCP/BOOTP Server with:
     * DHCP-Option 66 (TFTP server name) pointing to a local TFTP
       Server within the same subnet of the DHCP range
     * DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
       of the to be booted image
3. connect the port labled internet to your local network
4. keep the reset button pushed down and power on the board

The board should load and start the initramfs image from the TFTP
Server. Login as root/without password to the started LEDE via ssh
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.

Revert to RouterOS

Use the "rbcfg" package on in LEDE:
  * rbcfg set boot_protocol bootp
  * rbcfg set boot_device ethnand
  * rbcfg apply

Open Netinstall and reboot routerboard. Now netinstall sees routerboard
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.

Click on install again.

In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall

Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-10-14 10:48:29 +02:00
Mathias Kresin
1c4a116a30 ar71xx: add rssileds to WA850RE v1 image
A default rssileds config exists for the TP-Link WA850RE v1 but the
rssiled package is not included by default.

The compressed 17.01.3 image size increases by 3302 bytes which should
be tolerable even for a 4MB flash board.

Fixes: FS#1043

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-07 20:15:03 +02:00
Catrinel Catrinescu
cd4b60c329 ar71xx: ew-dorin target moved from legacy to generic
Embedded Wireless Dorin platform moved from legacy to generic

Signed-off-by: Catrinel Catrinescu <cc@80211.de>
2017-10-07 09:20:04 +02:00
Enrique Giraldo
b8b410fba3 ar71xx: add metadata to wpj344 and wpj558 images
This adds metadata to wpj344 and wpj558 images to prevent loading
firmware of wpj344 into wpj558 and vice versa. This until now was
possible and break the units and had to be recovered from the uboot.

Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
2017-09-10 22:15:04 +02:00
Enrique Giraldo
fefdb1e0b9 ar71xx: add support for COMFAST CF-E355AC
COMFAST CF-E355AC is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9531 + QCA9882.

Short specification:

- 2x 10/100 Mbps Ethernet, with PoE support
- 64MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, 802.11b/g/n
- 2T2R 5 GHz, 802.11ac/n/a
- built-in 4x 3 dBi antennas
- output power (max): 500 mW (27 dBm)
- 1x RGB LED, 1x button
- built-in watchdog chipset

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
[whitespace fixes, ac radio caldata offset fix]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-09-10 22:15:03 +02:00
Piotr Dymacz
90d8c0f0a2 ar71xx: add support for GL.iNet GL-USB150
GL.iNet GL-USB150 is an USB dongle WiFi router, based on Atheros AR9331.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- Realtek RTL8152B USB to Ethernet bridge (connected with AR9331 PHY4)
- 1T1R 2.4 GHz
- 2x LED, 1x button
- UART header on PCB

Flash instruction:

Vendor firmware is based on OpenWrt CC. GUI or sysupgrade can be used
to flash LEDE firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-09-10 22:14:43 +02:00
Piotr Dymacz
2ad2946777 ar71xx: image: use tplink-v1-header in place of mktplinkfw-kernel
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-22 23:29:50 +02:00
Piotr Dymacz
f08f754993 build: move mktplinkfw-combined command to image-commands.mk
We will need "mktplinkfw-combined" command also in the "ramips" target
for new MediaTek based TP-Link devices, with "safeloader" image type.

Also, rename the command to "tplink-v1-header", use "VERSION_DIST"
variable instead of "OpenWrt" and allow passing additional parameters.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-22 23:29:50 +02:00
Piotr Dymacz
b3cb0e7588 firmware-utils: mktplinkfw: rework combined image option
We use combined option in "mktplinkfw" tool for generating initramfs
kernel images and header for kernel inside "safeloader" image type (in
fact, only for TL-WR1043ND v4 at this moment).

There is also "mktplinkfw-kernel" tool, a stripped-down version, used
only for generating "simple" header, for safeloader image types.

This changes how "mktplinkfw" handles combined images (which then will
allow us to drop the stripped-down version of the tool):

- drop "ignore size" command line option (it was used only for combined
  images anyway)
- don't require "flash layout id" for combined images (we don't need and
  shouldn't limit size of the initramfs kernel and for kernels inside
  safeloader images, the "tplink-safeloader" tool does the size check)
- require kernel address and entry point in command line parameters for
  combined images (consequence of previous point)
- don't include md5 sum and firmware length values in header (they are
  needed only for update from vendor GUI and are ingored in case of
  initramfs and "tplink-safeloader" images)
- drop "fake" flash layout for TL-WR1043ND v4 as it's no longer needed

Also, adjust "mktplinkfw-combined" command in ar71xx/image/tp-link.mk to
match introduced changes in "mktplinkfw" tool.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-22 23:29:50 +02:00
Piotr Dymacz
0c6165d21a ar71xx: add support for ALFA Network AP121F
ALFA Network AP121F is a pocket-size router dedicated for VPN/TOR users.
Device is based on Atheros AR9331 WiSoC and is running a custom version
(updated from OpenWrt CC to LEDE 17.01 release) of NetAidKit firmware.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz
- 1x microSD (optional, on separate PCB)
- 3x LED, 1x button, 1x switch
- UART header on PCB

Flash instruction (under U-Boot web recovery mode):

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
   wait for first blink of all LEDs (indicates network setup), then keep
   button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-22 23:13:55 +02:00
Alexander Couzens
8c96eb2fdb
ar71xx/image: change unifi UBNT_CHIP to ar7240
Verified by OEM firmware images which contains the same
chip.

Tested-by: Andreas Bräu <ab@andi95.de>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-07-13 23:56:24 +02:00
Matthias Schiffer
16222a1010
ar71xx: set US region code for TP-Link TL-WR710N v1 image
Non-US versions of the TP-Link TL-WR710N v1 don't have a region code so
far, so we can just set US unconditionally.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-12 21:30:08 +02:00
Piotr Dymacz
9d07d2dc56 ar71xx: image: simplify Meraki MR16 device definition
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-09 23:46:53 +02:00
Henryk Heisig
096a604df0 ar71xx: add metadata to some TP-Link images
This commit adds metadata to TP-Link sysupgrade images
created by tplink-safeloader with uImage kernel header.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-07-09 22:45:59 +02:00
Piotr Dymacz
cf23547e57 ar71xx: fix TPLINK_BOARD_ID for Archer C58 and TL-WA855RE
Rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID for two ommited devices.

Fixes: 7d6c63d ("build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID")
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 15:09:52 +02:00
Piotr Dymacz
6165e4aab0 ar71xx: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
  resitors are missing on TX/RX lines)
- 1x micro USB (for power only)

Flash instructions:

Use "factory" image under vendor GUI.

Recovery instructions:

This device contains tftp recovery mode inside U-Boot. You can use it to
flash LEDE (use "factory" image) or vendor firmware.

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ar71xx-generic-tl-wr902ac-v1-squashfs-factory.bin"
   to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
   and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.

Root access over serial line in vendor firmware: root/sohoadmin.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 08:58:54 +02:00
Piotr Dymacz
a73471dea7 ar71xx: image: specify TPLINK_HWID for TP-Link RE450
TPLINK_HWID hasn't been specified for TP-Link RE450 since the begin.
As we don't want to break sysupgrade (all existing LEDE release images
for this board have TPLINK_HWID set to 0x0), set it explicitly to 0x0.

Fixes FS#852

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:46:08 +02:00
Piotr Dymacz
7d6c63d875 build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Henryk Heisig
b05c7193fd ar71xx: add support for TP-Link Archer C58 v1
TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm
QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 3x button
- UART header on PCB, RX, TX at TP4+5 (backside)

QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to
patch macaddress.

Flash instruction:

Use "factory" image directly in vendor GUI.

Recovery method:

1. Set PC to fixed ip address 192.168.0.66/24.
2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and
   rename it to "tp_recovery.bin".
3. Start a tftp server with the file "tp_recovery.bin" in its root
   directory.
4. Turn off the router.
5. Press and hold Reset button.
6. Turn on router with the reset button pressed and wait ~15 seconds.
7. Release the reset button and after a short time the firmware should
   be transferred from the tftp server.
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b $fileaddr 0x9f020000 $filesize
reset

This commit is based on GitHub PR#1112

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-06-29 10:37:36 +02:00
Federico Cappon
9fec39a033 ar71xx: add support for TP-Link TL-WA855RE v1
TP-Link TL-WA855RE v1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 550/397/198 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 2x LED (green and orange in the same package), 2x button
- UART: TP5(TX) and TP4(RX) test points on PCB

Flash instruction: use "factory" image directly in vendor GUI.

Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.

You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin

Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.

Signed-off-by: Federico Cappon <dududede371@gmail.com>
2017-06-29 10:37:36 +02:00
Piotr Dymacz
656ed7544f ar71xx: fix EnGenius ENS202EXT mtd definition
Use statically defined sizes for kernel and rootfs mtd partitions.
Vendor upgrade script writes both firmware parts independently which
ends up in a gap between kernel and rootfs images. This results in
incorrectly calculated rootfs_data start offset.

Also, fix IMAGE_SIZE, DEVICE_PACKAGES and drop redundant KERNEL
definition.

Fixes FS#835

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Camille Bilodeau
bb46b635df ar71xx: move Arduino Yun to generic building code
Migrate Arduino Yun from legacy to generic building code.

Note: the mtd partitioning is changed to adopt the LEDE default
partitioning. It allows to have a kernel bigger than 1280k. It is
necessary as kernel > 4.4 with default LEDE configuration grows
bigger.

To use the new partitioning, you need to update your U-Boot env in
advance:

setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro"
setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000"
saveenv

Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
2017-06-29 10:37:36 +02:00
Camille Bilodeau
2fa58a8d7c ar71xx: remove Arduino Yun 8 MiB prototype
The Arduino Yun has 16 MiB flash. Early prototype boards with 8 MiB were
not available for sell:

https://blog.arduino.cc/2013/08/21/updating-about-arduino-yun-and-arduino-robot/

Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
2017-06-29 10:37:36 +02:00
Alexander Couzens
d98cafc7b6
ar71xx/images/senao: fix reproducible issue using tar
Use deterministic sorting
Use numeric owner/group
Set uid/gid to 0

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-06-25 12:14:26 +02:00
Alexander Couzens
d6331d5583 ar71xx/image: make tar calls reproducible
Use --mtime when SOURCE_DATE_EPOCH is set.
Use gzip -n9z instead of tar z to remove
timestamp in gzip header.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-06-25 12:11:41 +02:00
Mathias Kresin
e7cd6f5d66 ar71xx: add AVM FRITZ!WLAN Repeater 300E support
Specifications:
* SoC: AR7242 (Virian 400MHz)
* RAM: 64 MB DDR (W9751G6JB-25)
* Flash: 16MB SPI flash (S25FL129PIF)
* WiFi: AR9382 (2.4/5GHz) + 2x SE2595L
* LAN: 1x1000M (PEF7071V)

To install LEDE via EVA bootloader, a FTP connection need to be
established to 192.168.178.1 within the first seconds after power on:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Piotr Dymacz
3ff31586eb ar71xx: image: simplify TP-Link devices definitions
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Piotr Dymacz
8b556fb056 ar71xx: image: fix TP-Link TL-WR710N v2/v2.1 BOARDNAME
All TP-Link TL-WR710N versions share the same machine code.

This has been working since the beginning as we don't use double-quotes
to protect spaces inside command line values. Thus, kernel interprets
'board=TL-WR710N v2' as 'board=TL-WR710N' and separate parameter 'v2'.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Piotr Dymacz
7efe0cd83d ar71xx: image: tp-link.mk: keep devices in alphabetical order
Keep TP-Link devices definitions in alphabetical order whenever it's
possible. Also group together similar devices or devices from the same
series.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Ludwig Thomeczek
b4711dbad3 ar71xx: add support for TP-Link Archer C25 v1
The TP-Link Archer C25 is a low-cost dual-band router.

Specification:

- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet

Some LEDs are controlled by an additional 74HC595 chip.

Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
[minor code style fixes, boards alphabetical order fixes,
reworked commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Serg Studzinskii
b7cc661615 ar71xx: add support for TP-Link TL-WR942N v1
TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on
Qualcomm/Atheros QCA9561.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x USB 2.0
- 11x LED (most are controlled by 74HC595)
- 2x button
- UART header on PCB*

* Serial console is disabled in OEM non-beta firmwares and corresponding
  GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by
  production (non-beta) U-Boot and firmware.

Currently not working:

1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs
   by some U-Boot versions.

Flash instruction under vendor GUI:

1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin".
2. Go to WEB interface and perform usual firmware upgrade.

FLash instruction under U-Boot recovery mode (doesn't work in beta
firmware):

1. Setup PC with static IP "192.168.0.66/24" and tftp server.
2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make
   it available to download from your tftp server.
3. Press "reset" button and power up the router, wait till "WPS" LED
   turns on.

Flash instruction under U-Boot, using UART (can be done only with
preinstalled UART-enabled U-Boot version!):

1. Use "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
   tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin
   erase 0x9f020000 +$filesize
   cp.b 0x81000000 0x9f020000 $filesize
   reset

Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
[minor code style fixes, extended commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
641af0c39d ar71xx: move WRTnode2Q to generic build target
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
636ae9e9a0 ar71xx: image: simplify Ubiquiti devices definitions
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
01aa23acf7 ar71xx: image: mikrotik: shorten DEVICE_TITLE
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
7bc5571d14 ar71xx: image: use simply expanded variables
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
80136e57a4 ar71xx: image: update GL.iNet boards DEVICE_TITLE
Use "GL.iNet" as vendor name (based on information from the vendor, this
is registered name of the company) and align model names with official
website.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:31:25 +02:00
Piotr Dymacz
93198b8335 ar71xx: image: fix 8devices boards DEVICE_TITLE
Be consistent with DEVICE_TITLE syntax and use vendor + board names.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:30:05 +02:00
Piotr Dymacz
bd92a6cf57 ar71xx: image: drop unused mtdlayouts from legacy.mk
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:22:46 +02:00
Piotr Dymacz
708cc2bd3c ar71xx: image: cosmetic: drop redundant empty lines
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:22:46 +02:00
Piotr Dymacz
e83cac1a8f ar71xx: image: add ROOTFS_SIZE to DEVICE_VARS
Also use ROOTFS_SIZE variable in place of static values.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:22:46 +02:00
Piotr Dymacz
c00fb14329 ar71xx: image: keep custom Build/* functions in separate files
Most of the custom Build/* functions in ar71xx target are rarely used by
image building code for devices from more than one subtarget. As they
don't need to be always included, move them to corresponding *.mk files.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:22:46 +02:00
Piotr Dymacz
3a3cd0ac43 ar71xx: image: keep DEVICE_VARS and Build/* at the beginning
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:21:45 +02:00
Piotr Dymacz
af27dd1a51 ar71xx: image: simplify Compex devices definitions
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 19:06:49 +02:00
Piotr Dymacz
43c0ef1010 ar71xx: image: drop redundant kmod-usb-ohci from DEVICE_PACKAGES
kmod-usb-ohci is needed only on devices with AR71xx and AR7240 SoCs.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 19:06:49 +02:00
Piotr Dymacz
05e276c071 ar71xx: image: drop redundant uboot-envtools from DEVICE_PACKAGES
uboot-envtools is already included in DEFAULT_PACKAGES for ar71xx.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 19:06:49 +02:00
Piotr Dymacz
6173f6d8f1 ar71xx: move Wallys DR344 to generic build target
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-30 14:34:09 +02:00
Marty Plummer
558d86923e ar71xx: add support for EnGenius ENS202EXT
EnGenius ENS202EXT is an outdoor wireless access point with
2-port 10/100 switch, detachable antennas and proprietery PoE.

The device is based on Qualcomm/Atheros AR9341 v1.

Specifications:
- 535/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM
- 16 MB of FLASH
- UART (J1) header on PCB (unpopulated)
- 2x 10/100 Mbps Ethernet
- 2.4 GHz, up to 26dBm
- 2x external, detachable antennas
- 7x LED, 1x button

Flash instructions:

You have three options:

- Use the vendor firmware upgrade page on the web interface and give
it the factory.img. This is the easiest way to go about it.

- If you have serial access during u-boot, interrupt the normal boot
(any key before timeout) and run 'run failsafe_boot'; this will bring
you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've
bricked the normal firmware.

- Use the vendor's management cli, which can be accessed via telnet
with the same credentials as the web login (default admin:admin), then
issue the following commands:

*** Hi admin, welcome to use cli(V-1.6.7) ***
---========= Commands Help =========---
      stat -- Status
       sys -- System
    wless2 -- 2.4G-Wireless
      mgmt -- Management
      tree -- Tree
      help -- Help
    reboot -- Reboot
ens202ext>mgmt
  Management
---========= Commands Help =========---
     admin -- Administration
     mvlan -- Management VLAN settings
      snmp -- SNMP settings
    backup -- Backup/Restore settings
    autorb -- Auto reboot settings
   fwgrade -- Firmware upgrade
      time -- Time settings
   wifisch -- Wifi schedule
       log -- Log
      diag -- Diagnostics
      disc -- Device Discovery
    logout -- Logout
      help -- Help
      exit -- Exit
ens202ext/mgmt>fwgrade
  Management --> Firmware upgrade
---========= Commands Help =========---
      fwup -- Firmware upgrade
      help -- Help
      exit -- Exit
ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin

Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
2017-05-30 14:15:25 +02:00
Andrey Polischuk
0f21873f7f ar71xx: fix LED defines for TP-Link TL-WR740N v6
Signed-off-by: Andrey Polischuk <androld.b@gmail.com>
[changed commit subject, dropped redundant kernel config symbol]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-30 14:15:25 +02:00
Filip Moc
43e4e1f4a5 Move enablemodem from ramips to new package adb-enablemodem and make it used also by TL-MR6400
Signed-off-by: Filip Moc <lede@moc6.cz>
2017-05-27 07:54:40 +02:00
Filip Moc
a639cbfd00 ar71xx: Add support for TP-Link MR6400
You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin
on 192.168.0.66/24, connect to any ethernet port and power on device while
holding the reset button). Flashing via OEM web interface does not work.

Hardware Specification (v1.0 EU):
 - SoC: QCA9531
 - Flash: Winbond W25Q64FV (8MiB)
 - RAM: EtronTech EM6AB160TSE-5G (64MiB)
 - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
 - Ethernet: 2NIC (3x100M + 1x100M)
 - WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
 - Power: DC 12V 1A

Signed-off-by: Filip Moc <lede@moc6.cz>
2017-05-27 07:54:21 +02:00
Matthias Fritzsche
a4e63e2679 ar71xx: change image version for ubiquiti devices
changes the image version from hardcoded OpenWrt to
$VERSION_DIST. AirOS shows a notification with the image version
during a firmware upgrade.

fixes #582

Signed-off-by: Matthias Fritzsche <txt.file@txtfile.eu>
2017-05-25 09:22:37 +02:00
John Crispin
bad2f9c4dc Revert "ar71xx: Add support for Teltonika RUT900"
This reverts commit 224e5f5efa.

pepe2k pointed out that this was not ready to merge

Signed-off-by: John Crispin <john@phrozen.org>
2017-05-18 15:31:47 +02:00
Steffen Weinreich
224e5f5efa ar71xx: Add support for Teltonika RUT900
Teltonika RUT900 is a Router with LTE dual SIM, WiFi, 4x Ethernet
ports, I/O, RS232, RS485, GPS.

The device ist based on a Atheros AR9344 rev 3,

Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM
- 16 MB of FLASH
- Serial Console header on a Card Board edge connector
- 4x 10/100 Mbps Ethernet (3x LAN, 1x WAN)
- 2.4 GHz Wifi
- 2x external, detachable Wifi antennas
- LTE Modem Huawei ME909u-521 (Also other Modem seen)
- 2x LTE antennas
- 1x GPS antenna
- 7x LED, 1x button
- 1x USB Connector
- 1x Serial RS232
- 1x Serial RS485
- 1x MicroSD Card

The GPL sources of the device are available at www.teltonika.lt/gpl/
and are based on OpenWRT Barrier Breaker (14.07)

Running from tftp:

The Router starts into the uboot Webupdater if the Button ist pressed
more than 3 seconds, if no Network cable is attached it starts the
uboot serial console, from there the router loads the firmware image
via tftpboot from 192.168.1.2:firmware.bin (the router has the
192.168.1.1). With bootm the loaded image will be booted.

Signed-off-by: Steffen Weinreich <steve@weinreich.org>
2017-05-18 14:47:53 +02:00
Chris Blake
10d11859df ar71xx: add support for Aerohive AP-121
This adds support for Aerohive AP-121 access point.

Specification:
- SoC: Atheros AR9344-BC2A at 560MHz
- WiFi 1: 2.4GHz Atheros AR9340? - SoC
- WiFi 2: 5.0GHz Atheros AR9382-AL1A
- Memory: 128MB from 2x Nanya NT5TU32M16DG-AC
- SPI: 1MB Macronix MX25L8006E
- NAND: 128MB Hynix H27U1G8F2BTR-BC
- Ethernet: Atheros AR8035-A
- USB: 1x 2.0
- TPM: Atmel SC3204

Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter
a password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, download and flash LEDE factory image over tftp:

dhcp;
setenv serverip tftp-server-ip;
tftpboot 0x81000000 lede-ar71xx-nand-hiveap-121-squashfs-factory.bin;
nand erase 0x800000 0x800000;
nand write 0x81000000 0x800000 0x800000;
reset;

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[minor text changes in commit subject and description, fixed
alphabetical order in etc/diag.sh, use only model name in lib/ar71xx.sh,
fixed code style issues in mach-hiveap-121.c, ubinized factory image]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-15 22:58:59 +02:00
Mantas Pucka
68b5d34f69 ar71xx: add support for 8devices Rambutan development board
Rambutan is a Wifi module based on QCA9550/9557
http://www.8devices.com/products/rambutan

This commit adds basic support for Rambutan development kit

Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of DDR2 RAM
- 128 MB of NAND Flash
- 1x 100Mbps Ethernet
- 1x 1000Mbps Ethernet (PHY on dev-kit)
- 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz
- 2x U.FL connectors on module, chip antennas on dev-kit
- 1x miniPCIe slot
- 1x USB2.0 host socket + 1x USB2.0 pins on 2.54mm header

Flash instructions:
Stock firmware is OpenWrt, so use:
 sysupgrade -n /tmp/lede-ar71xx-nand-rambutan-squashfs-sysupgrade.tar
or upgarde from GUI (don't save config)
Use factory image to flash from U-Boot:
 tftpboot 80060000 lede-ar71xx-nand-rambutan-squashfs-factory.ubi
 nand erase.part ubi
 nand write 80060000 ubi ${filesize}

Signed-off-by: Mantas Pucka <mantas@8devices.com>
[split support in uboot-envtools package into a separate commit,
fixed alphabetical order in lib/preinit/05_set_iface_mac_ar71xx]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-15 22:43:33 +02:00
Ludwig Thomeczek
43a7a1a05e ar71xx: add support for UniFi-AC-Mesh
This adds the build option for the new UniFi AC Mesh.
It is a direct hardware copy from the AC Lite.

- SoC: QCA9563-AL3A (775Mhz)
- RAM: 128MiB
- Flash: 16MiB - dual firmware partitions!
- LAN: 1 1000M - POE
- Wireless:
        2.4G: QCA9563
          5G: UniFi Chip, QCA988X compatible

Thanks to Frank Dietz for testing.

Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
[wrapped too long lines in mach-ubnt-unifiac.c]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-15 22:43:33 +02:00
Piotr Dymacz
1c56a7929a ar71xx: move Zbtlink ZBT-WE1526 to generic build target
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-15 22:43:33 +02:00
Felix Fietkau
c536c50171 ar71xx: enable nand-utils in the mikrotik subtarget to ensure it makes it to initramfs
Without it, sysupgrade from initramfs to nand fails

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-05-12 13:29:55 +02:00
Piotr Dymacz
190db43615 ar71xx: tp-link.mk: always include device version in image and DEVICE_TITLE
There are currently several supported TP-Link devices without specified
version number in image name and/or DEVICE_TITLE (e.g. WBS210, WBS510,
TL-WR810N, TL-WA7510N, TL-WPA8630), but vendor website shows that there
are already more than one version of them on the market.

For devices like Archer C5, which second version is based on a total
different platform, missing version number in DEVICE_TITLE (used in
menuconfig) might be misleading for users.

To make it less confusing for users and easier to maintain in future,
include version number in image name and DEVICE_TITLE for all TP-Link
devices, even if there is only one version of device at the moment.

Also, keep DEVICE_TITLE in same format for all TP-Link devices.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Acked-by: John Crispin <john@phrozen.org>
2017-04-03 12:29:07 +02:00
Vittorio Gambaletta
539e2a78f0 ar71xx: add TP-LINK TL-WR841N/ND v12 image
This router has the same hardware as TP-LINK TL-WR841N/ND v11 (same FCC
ID, same TFTP image name...).

If the stock firmware web interface doesn't accept LEDE factory image,
it can be flashed via the U-Boot TFTP recovery mode, by long-pressing
the reset button after power on.

The TFTP image name is wr841nv11_tp_recovery.bin (yes, v11, not v12).

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
2017-04-03 12:29:07 +02:00
Christian Mehlis
dc4eae7a8c ar71xx: Compex WPJ563 support
Specification:
- SoC: Qualcomm Atheros QCA9563 (775 MHz, MIPS 74Kc)
- RAM: 128 MiB
- Storage: 16MB NOR flash
- Wireless: Built into QCA9563 (Dragonfly), PHY modes b/g/n, 3x3 MIMO
- Ethernet: 2x1G

Tested and working:
- ethernet / switch / lan / wan
- 2.4GHz SoC wifi
- PCIe
- leds
- buzzer

Ramload:
- tftpboot 0x84000000 lede-ar71xx-generic-wpj563-16M-initramfs-uImage.bin
- bootm 0x84000000

Install:
- tftpboot 0x80500000 lede-ar71xx-generic-wpj563-16M-squashfs-sysupgrade.bin
- erase 0x9f030000 +$filesize
- erase 0x9f680000 +1
- cp.b $fileaddr 0x9f030000 $filesize

Erasing 0x9f680000 is required because uboot defines
"bootcmd=bootm 0x9f680000 || bootm 0x9f030000", so it first tries to boot
the higher address. I think the 16 mb flash are intended to be used as
8+8mb for a fallback image. In my hardware only the lower address has a
bootable image. But to make sure future hardware will boot lede too, I
erase one block, so uboot will skip this address.

Signed-off-by: Christian Mehlis <christian@m3hlis.de>
2017-03-30 09:57:22 +02:00
John Crispin
95c333a3b5 ar71xx: drop default CONSOLE values
Compex boards dont need to set these as they are default.

Signed-off-by: John Crispin <john@phrozen.org>
2017-03-29 09:22:46 +02:00
Christian Mehlis
be11ce8f26 ar71xx: move Compex WPJ342 to generic build target
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
2017-03-29 09:04:08 +02:00
Christian Mehlis
0af487033e ar71xx: move Compex WPJ344 to generic build target
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
2017-03-29 09:04:08 +02:00
Christian Mehlis
f5ece7326a ar71xx: move Compex WPJ531 to generic build target
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
2017-03-29 09:04:08 +02:00
Christian Mehlis
f940fe8964 ar71xx: move Compex WPJ558 to generic build target
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
2017-03-29 09:04:08 +02:00
Mathias Kresin
86a0cbb333 treewide: select ath10k firmware explicit
Do not rely on the default firmware selected by ath10k.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-24 08:09:39 +01:00
Piotr Dymacz
597c9f0be5 ar71xx: image: fix indentation
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-23 22:02:47 +01:00