Commit Graph

453 Commits

Author SHA1 Message Date
Nian Bohung
454ebdf1c9 linux-firmware: add firmware for intel ax200
Signed-off-by: Nian Bohung <n0404.n0404@gmail.com>
2021-11-20 21:08:25 +01:00
Nian Bohung
b1db558555 cypress-nvram: fix firmware is not exist for raspberry pi compute 4
Fix file "brcmfmac43455-sdio.raspberrypi,4-compute-module.txt" is not exist.

Signed-off-by: Nian Bohung <n0404.n0404@gmail.com>
2021-11-20 21:08:25 +01:00
Richard Yu
12d33d388c ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0)
P&W R619AC is a IPQ4019 Dual-Band AC1200 router.
It is made by P&W (p2w-tech.com) known as P&W R619AC
but marketed and sold more popularly as G-DOCK 2.0.

Specification:

* SOC: Qualcomm Atheros IPQ4019 (717 MHz)
* RAM: 512 MiB
* Flash: 16 MiB (NOR) + 128 MiB (NAND)
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN)
* Wireless:
  - 2.4 GHz b/g/n Qualcomm Atheros IPQ4019
  - 5 GHz a/n/ac Qualcomm Atheros IPQ4019
* USB: 1 x USB 3.0
* LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED)
* Input: 1 x reset
* 1 x MicroSD card slot
* Serial console: 115200bps, pinheader J2 on PCB
* Power: DC 12V 2A
* 1 x Unpopulated mPCIe Slot (see below how to connect it)
* 1 x Unpopulated Sim Card Slot

Installation:
1. Access to tty console via UART serial
2. Enter failsafe mode and mount rootfs
   <https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset>
3. Edit inittab to enable shell on tty console
   `sed -i 's/#ttyM/ttyM/' /etc/inittab`
4. Reboot and upload `-nand-factory.bin` to the router (using wget)
5. Use `sysupgrade` command to install

Another installation method is to hijack the upgrade server domain
of stock firmware, because it's using insecure http.

This commit is based on @LGA1150(at GitHub)'s work
<a4932c8d5a>
With some changes:
1. Added `qpic_bam` node in dts. I don't know much about this,
   but I observed other dtses have this node.
2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not
   working. This fix is from
   <51143b4c75>
3. Removed the 32MB NOR variant.
4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes
   wlan2g led light up.
5. Added ethphy led config in dts.
6. Changed nand partition label from `rootfs` to `ubi`.

About the 128MiB variant: The stock bootloader sets size of nand to 64MiB.
But most of this devices have 128MiB nand. If you want to use all 128MiB,
you need to modify the `MIBIB` data of bootloader. More details can be
found on github:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060>
For instructions on how to flash the MIBIB partition from u-boot console:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232>

About the Mini PCIe slot: (from "ygleg")
"The REFCLK signals on the Mini PCIe slot is not connected on
this board out of the box. If you want to use the Mini PCIe slot
on the board, you need to (preferably) solder two 0402 resistors:
R436 (REFCLK+) and R444 (REFCLK-)..."
This and much more information is provoided in the github comment:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670>

Signed-off-by: Richard Yu <yurichard3839@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
[Added comment about MIBIB+128 MiB variant. Added commit
message section about pcie slot. Renamed gpio-leds' subnodes
and added color, function+enum properties.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-14 14:28:34 +01:00
Christian Lamparter
fd717f54be ipq40xx: detangle ath10k-board-qca4019 from ath10k-firmware-qca4019*
Back in the day, the board-2.bin came with ath10k-firmware-qca4019.
This changed with
commit c3b2efaf24 ("linux-firmware: ath10k: add board firmware packages")
which placed the board-2.bin into a separate package: ath10k-board-qca4019.
This was great, because it addressed one of the caveat of the original
ipq-wifi package:
commit fa03d441e9 ("firmware: add custom IPQ wifi board definitions")

|  2. updating ath10k-firmware-qca4019 will also replace
|      the board-2.bin. For this cases the user needs to
|      manually reinstall the wifi-board package once the
|      ath10k-firmware-qca4019 is updated.

This could be extended further so that ipq-wifi packages
no longer use "install-override" and the various QCA4019
variants list the ath10k-board-qca4019 as a CONFLICT
package.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-30 16:32:59 +02:00
Christian Lamparter
dbb4c47798 wireless-regdb: update to version 2021.08.28
e983a25 Update regulatory rules for Ecuador (EC)
a0bcb88 wireless-regdb: Update regulatory rules for Norway (NO) on 6 and 60 GHz
cdf854d wireless-regdb: Update regulatory rules for Germany (DE) on 6GHz
86cba52 wireless-regdb: reduce bandwidth for 5730-5850 and 5850-5895 MHz in US
6fa2384 wireless-regdb: remove PTMP-ONLY from 5850-5895 MHz for US
9839e1e wireless-regdb: recent FCC report and order allows 5850-5895 immediately
42dfaf4 wireless-regdb: update 5725-5850 MHz rule for GB

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-23 19:31:32 +02:00
Sven Eckelmann
8b09070820 ipq-wifi: Work around Plasma Cloud PA1200 5GHz crash
It was noticed [1] that the ath10k firmware crashes on 5GHz since OpenWrt
21.02.0. The problem seems to be triggered by the the nonLinearTxFir field
in the 5GHz BDF. If baseEepHeader.nonLinearTxFir (offset 0xc2) is 1 then
the firmware just crashes when setting up the 5Ghz radio using `ifconfig
wlan1 up`:

  ath10k_ahb a800000.wifi: firmware crashed! (guid 9e36ee82-4d2c-4c63-b20b-609a1eaca30c)
  ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
  ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
  ath10k_ahb a800000.wifi: firmware ver 10.4-3.6-00140 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 ba79b746
  ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:17 crc32 5f400efc
  ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1
  ath10k_ahb a800000.wifi: firmware register dump:
  ath10k_ahb a800000.wifi: [00]: 0x0000000B 0x000015B3 0x009C3C27 0x00975B31
  ath10k_ahb a800000.wifi: [04]: 0x009C3C27 0x00060530 0x00000018 0x004176B8
  ath10k_ahb a800000.wifi: [08]: 0x00405A50 0x00412A30 0x00000000 0x00000000
  ath10k_ahb a800000.wifi: [12]: 0x00000009 0x00000000 0x009B9742 0x009B974F
  ath10k_ahb a800000.wifi: [16]: 0x00971238 0x009B9742 0x00000000 0x00000000
  ath10k_ahb a800000.wifi: [20]: 0x409C3C27 0x004053DC 0x00000D2C 0x00405A60
  ath10k_ahb a800000.wifi: [24]: 0x809C3E13 0x0040543C 0x00000000 0xC09C3C27
  ath10k_ahb a800000.wifi: [28]: 0x809B9AC5 0x0040547C 0x00412A30 0x0040549C
  ath10k_ahb a800000.wifi: [32]: 0x809B8ECD 0x0040549C 0x00000001 0x00412A30
  ath10k_ahb a800000.wifi: [36]: 0x809B8FF3 0x004054CC 0x00412838 0x00000014
  ath10k_ahb a800000.wifi: [40]: 0x809BEF98 0x0040551C 0x0041627C 0x00000002
  ath10k_ahb a800000.wifi: [44]: 0x80986D47 0x0040553C 0x0041627C 0x00416A88
  ath10k_ahb a800000.wifi: [48]: 0x809CBB0A 0x0040559C 0x0041ACC0 0x00000000
  ath10k_ahb a800000.wifi: [52]: 0x809864EE 0x0040560C 0x0041ACC0 0x00000001
  ath10k_ahb a800000.wifi: [56]: 0x809CA8A4 0x0040564C 0x0041ACC0 0x00000001
  ath10k_ahb a800000.wifi: Copy Engine register dump:
  ath10k_ahb a800000.wifi: [00]: 0x0004a000  14  14   3   3
  ath10k_ahb a800000.wifi: [01]: 0x0004a400  16  16  22  23
  ath10k_ahb a800000.wifi: [02]: 0x0004a800   3   3   2   3
  ath10k_ahb a800000.wifi: [03]: 0x0004ac00  15  15  15  15
  ath10k_ahb a800000.wifi: [04]: 0x0004b000   4   4  44   4
  ath10k_ahb a800000.wifi: [05]: 0x0004b400   3   3   2   3
  ath10k_ahb a800000.wifi: [06]: 0x0004b800   1   1   1   1
  ath10k_ahb a800000.wifi: [07]: 0x0004bc00   1   1   1   1
  ath10k_ahb a800000.wifi: [08]: 0x0004c000   0   0 127   0
  ath10k_ahb a800000.wifi: [09]: 0x0004c400   0   0   0   0
  ath10k_ahb a800000.wifi: [10]: 0x0004c800   0   0   0   0
  ath10k_ahb a800000.wifi: [11]: 0x0004cc00   0   0   0   0
  ath10k_ahb a800000.wifi: failed to update channel list: -108
  ath10k_ahb a800000.wifi: failed to set pdev regdomain: -108
  ath10k_ahb a800000.wifi: failed to create WMI vdev 0: -108
  ieee80211 phy1: Hardware restart was requested

Since no actual solution is known (besides downgrading the ath10k firmware)
it seems to be better to disable the nonLinearTxFir for now.

[1] https://lore.kernel.org/ath10k/3423718.UToCqzeSYe@ripper/

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-09-23 20:50:58 +02:00
Sven Eckelmann
e0721608f9 ipq-wifi: Update Plasma Cloud PA1200 BDFs to firmware 3.5.12
The official Plasma Cloud firmware adjusted the BDFs to contain new
conformance test limits and target power values. These should be imported
to avoid emissions outside the allowed limits.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-09-23 20:50:58 +02:00
Sven Eckelmann
ebe800765e ipq-wifi: Drop empty wifi package for Netgear WAC510
The ipq-wifi-netgear_wac510 package is not selected by any device and would
be empty anyway. The default board-2.bin from ath10k-board-qca4019 is
therefore used for this device and the package doesn't provide any visible
features.

Fixes: b126d9c3a3 ("ipq40xx: add netgear wac510 support")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-09-12 18:52:30 +02:00
Damien Mascord
d996b47be0 linux-firmware: add 2G and 5G precal binaries for QCA99X0
Some devices (such as Extreme Networks WS-AP3959i-ROW) do not contain
precal binaries in ART, and the precal in the cards eeprom causes
firmware load errors.

These firmware files were previously in linux-firmware,
so these are adding them back and renaming to be cleaner.

Signed-off-by: Damien Mascord <tusker@tusker.org>
2021-07-25 13:52:38 +02:00
Tomas Lara
4413537430 linux-firmware: update to 20210511
git log --pretty=oneline --abbrev-commit 20201118..20210511

7685cf4 (HEAD, tag: 20210511) nvidia: Update Tegra194 XUSB firmware to v60.09
cf32752 nvidia: Update Tegra186 XUSB firmware to v55.18
cb8ca82 nvidia: Update Tegra210 XUSB firmware to v50.26
f99d6a1 linux-firmware: update firmware for mhdp8546
ecdfcf8 Merge branch 'adlp_dmc_firmware' of git://anongit.freedesktop.org/drm/drm-firmware into main
547b202 Merge https://github.com/suraj714/linux-firmware-venus into main
3d32f21 i915: Add ADL-P DMC Support
3f23f51 amdgpu: add new polaris 12 MC firmware
a2565bb firmware: nvidia: Add VIC firmware for Tegra194
17ec2a5 qcom: add gpu firmwares for sc7280
b653cf4 Merge https://github.com/pkshih/linux-firmware into main
2a96c08 brcm: Add a link to enable khadas VIM2's WiFi
ffc64a2 rtw89: 8852a: update fw to v0.13.8.0
3e3497c rtl_bt: Update RTL8852A BT USB firmware to 0xD9A8_7893
c7b11ed qcom: Add venus firmware files for VPU-2.0
2f4f0f8 rtw89: 8852a: update fw to v0.13.8.0
fa0efef linux-firmware: Update firmware file for Intel Bluetooth AX210
9be3daa linux-firmware: Update firmware file for Intel Bluetooth 9560
687d64a linux-firmware: Update firmware file for Intel Bluetooth 9260
a7f1249 linux-firmware: Update firmware file for Intel Bluetooth AX200
47650a0 linux-firmware: Update firmware file for Intel Bluetooth AX201
195ecf1 linux-firmware: Intel BT 7265: Fix Security Issues
4116d72 linux-firmware: Update firmware file for Intel Bluetooth 8265
ca83c73 qcom: update venus firmware files for v5.4
1334578 Merge branch 'mrvl-prestera' of https://github.com/PLVision/linux-firmware into main
16052e4 mrvl: prestera: Add Marvell Prestera Switchdev firmware 3.0 version
bdf929d rtw88: 8822c: Update normal firmware to v9.9.9
0b558e8 brcm: add missing symlink for Pi Zero W NVRAM file
cfa004c amdgpu: update arcturus firmware from 21.10
d5567c5 amdgpu: update navy flounder firmware from 21.10
ef5ea5d amdgpu: update sienna cichlid firmware from 21.10
f35700f amdgpu: update vega20 firmware from 21.10
1be98f1 amdgpu: update picasso firmware from 21.10
fee0497 amdgpu: update navi14 firmware from 21.10
15003b0 amdgpu: update green sardine firmware from 21.10
64555fb amdgpu: update vega12 firmware from 21.10
eb07276 amdgpu: update navi12 firmware from 21.10
e36c82a amdgpu: update vega10 firmware from 21.10
4a5eaa2 amdgpu: update renoir firmware from 21.10
65eb326 amdgpu: update navi10 firmware from 21.10
8bdca03 amdgpu: update raven2 firmware from 21.10
c9e44ca amdgpu: update raven firmware from 21.10
bc3e610 rtl_nic: add new firmware for RTL8153 and RTL8156 series
8528618 Merge branch 'for-upstream' of git://git.chelsio.net/pub/git/linux-firmware into main
940b7f4 cxgb4: Update firmware to revision 1.25.4.0
f66adc3 Merge branch 'main' of gitolite.kernel.org:/pub/scm/linux/kernel/git/maks/linux-firmware into main
f350e91 Merge https://github.com/rjliao-qca/qca-btfw into main
9bc1bcc Merge https://github.com/Netronome/linux-firmware into main
2f30708 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2438
393f272 brcm: Link CM4's WiFi firmware with DMI machine name.
73144e0 linux-firmware: Update firmware file for Intel Bluetooth AX201
8ab7aba amdgpu: update navi14 smc firmware
4fe6e53 amdgpu: update navi10 SMC firmware
c296849 QCA: Update Bluetooth firmware for QCA6174
d6a18e9 WHENCE: link to similar config file for rtl8821a support
6c419ae nfp: update Agilio SmartNIC flower firmware to rev AOTC-2.14.A.6
af1ca28 amdgpu: add arcturus firmware
0dd245d Merge branch 'sm8250-new-fw' of https://github.com/lumag/linux-firmware into main
55cab07 rtl_bt: Add rtl8723bs_config-OBDA0623.bin symlink
2548d06 brcm: Add nvram for the Chuwi Hi8 (CWI509) tablet
e45c137 brcm: Add nvram for the Predia Basic tablet
d8fa0cf qcom: sm8250: update remoteproc firmware
84af0e0 qcom: update a650 firmware files
3f026a2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x59A_76A3
c82cb46 amdgpu: update sienna cichlid firmware for 20.50
24fe696 amdgpu: update vega20 firmware for 20.50
e05d197 amdgpu: update picasso firmware for 20.50
76d07cd amdgpu: update navi14 firmware for 20.50
b2fc037 amdgpu: update vega12 firmware for 20.50
25451a4 amdgpu: update navi12 firmware for 20.50
b938597 amdgpu: update vega10 firmware for 20.50
2542ba7 amdgpu: update renoir firmware for 20.50
b55d063 amdgpu: update navi10 firmware for 20.50
1a62f28 amdgpu: update raven2 firmware for 20.50
4df488f amdgpu: update raven firmware for 20.50
a29bdb2 amdgpu: add initial support for navy flounder
3568f96 (tag: 20210315) linux-firmware: Update firmware file for Intel Bluetooth AX210
9e96e50 linux-firmware: Update firmware file for Intel Bluetooth AX200
c8d0db5 linux-firmware: Update firmware file for Intel Bluetooth AX201
5e2a387 Merge tag 'iwlwifi-fw-2021-03-05-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware into main
b0d3e31 rtw88: 8822c: Update normal firmware to v9.9.6
5a2fd63 iwlwifi: add new FWs from core59-66 release
4f54906 iwlwifi: update 9000-family firmwares
11b7607 iwlwifi: update 7265D firmware
e425f76 Merge branch 'add-silabs-wf200' of github.com:jerome-pouiller/linux-firmware into main
5ecd13f Mellanox: Add new mlxsw_spectrum firmware xx.2008.2406
58fb90a linux-firmware: add frimware for mediatek bluetooth chip (MT7921)
e576a1b rtw89: 8852a: add firmware v0.9.12.2
048a7cb WHENCE: add missing symlink for BananaPi M3
aa6c6e7 Add symlink for BananaPi M2 to brcmfmac43430-sdio config
58825f7 brcm: Fix Raspberry Pi 4B NVRAM file
520f71b silabs: add new firmware for WF200
f7915a0 amdgpu: add initial firmware for green sardine
80cb579 rtw88: RTL8822C: Update normal firmware to v9.9.5
b79d239 (tag: 20210208) Merge branch 'DG1-guc-huc-ADLS-dmc' of git://anongit.freedesktop.org/drm/drm-firmware into main
66970e1 Merge branch 'qcom-rb5' of https://github.com/lumag/linux-firmware into main
cf6fc2b Mellanox: Add new mlxsw_spectrum firmware xx.2008.2304
391fd50 linux-firmware: add firmware for MT7921
c5e3240 rtw88: RTL8821C: Update firmware to v24.8
d33d2d8 linux-firmware: Update firmware file for Intel Bluetooth AX210
3027ae4 linux-firmware: Update firmware file for Intel Bluetooth AX200
13979c3 linux-firmware: Update firmware file for Intel Bluetooth AX201
348d8a9 i915: Add DMC v2.01 for ADL-S
f33f1f7 i915: Add HuC v7.7.1 for DG1
6a422f5 i915: Add GuC v49.0.1 for DG1
df822a8 qcom: Add venus firmware files for VPU-1.0
11a1db1 qcom: Add SM8250 Compute DSP firmware
e55248b qcom: Add SM8250 Audio DSP firmware
da74cc6 qcom: add firmware files for Adreno a650
0578970 brcm: Link RPi4's WiFi firmware with DMI machine name.
d528862 brcm: Add NVRAM for Vamrs 96boards Rock960
870b805 brcm: Update Raspberry Pi 3B+/4B NVRAM for downstream changes
a28a590 cypress: Fix link direction
060ad8b cypress: Link the new cypress firmware to the old brcm files
0f0aefd brcm: remove old brcm firmwares that have newer cypress variants
f580dc2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x059A_25CB
7df2220 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099a_7253
e79405d rtl_bt: Add firmware and config files for RTL8852A BT USB chip
ef3813d rtl_bt: Update RTL8821C BT(USB I/F) FW to 0x829a_7644
646f159 (tag: 20201218) make AP6212 in bananpi m2 plus/zero work
28185ec linux-firmware: Update firmware file for Intel Bluetooth AX210
23da869 linux-firmware: Update firmware file for Intel Bluetooth AX200
2099248 linux-firmware: Update firmware file for Intel Bluetooth AX201
94de5e2 linux-firmware: Update firmware file for Intel Bluetooth 9560
27a3689 linux-firmware: Update firmware file for Intel Bluetooth 9260
5c3c4af Merge branch 'lt9611uxc' of https://github.com/lumag/linux-firmware into main
aaed4a8 Merge branch 'v1.1.6' of https://github.com/irui-wang/linux_fw_vpu_v1.1.6 into main
d8c9865 Merge branch 'master' of https://github.com/sampnimm/linux-firmware-BT into main
63ab3db linux-firmware: add firmware for Lontium LT9611UXC DSI to HDMI bridge
0fe0fe0 mediatek: update MT8173 VPU firmware to v1.1.6
1a08ec9 QCA : Updated firmware files for WCN3991
7455a36 Merge branch 'guc_v49' of git://anongit.freedesktop.org/drm/drm-firmware into main
7eb7fda linux-firmware: Update firmware file for Intel Bluetooth AX210
5cbf459 linux-firmware: Update firmware file for Intel Bluetooth AX210
c487f7d i915: Add GuC firmware v49.0.1 for all platforms
d9ffb07 i915: Remove duplicate KBL DMC entry
b362fd4 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2018
bc9cd0b linux-firmware: Update AMD SEV firmware
54c797a amdgpu: add sienna cichlid firmware for 20.45
1340e9c amdgpu: update vega20 firmware for 20.45
b260c9c amdgpu: update vega12 firmware for 20.45
d683bd5 amdgpu: update vega10 firmware for 20.45
7c81cc2 amdgpu: update renoir firmware for 20.45
3619e57 amdgpu: update navi14 firmware for 20.45
68ce0fb amdgpu: update navi12 firmware for 20.45
e889b80 amdgpu: update navi10 firmware for 20.45
f4edc15 amdgpu: update raven2 firmware for 20.45
e71210f amdgpu: update raven firmware for 20.45

Signed-off-by: Tomas Lara <tl849670@gmail.com>
[rebased; removed brcmfmac changes due to removed firmware]
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-06-08 00:38:41 +02:00
Josef Schlehofer
ff2bb16730 linux-firmware: update to version 20210315 and trim down broadcom FW
In there linux-firmware repository located in kernel, there were removed old
broadcom firmware [1] as they seem to be likely vulnerable to KrØØk vulnerability
(CVE-2019-15126), because Cypress released new versions and superseded
by it.

In OpenWrt, there is Makefile for cypress-firmware, which already provides
the same named packages like it was in linux-firmware. For example, cypress-firmware-43455-sdio
provides brcmfmac-firmware-43455-sdio [2].

Changelog between 2020118 and 20210315:
3568f96 (tag: 20210315) linux-firmware: Update firmware file for Intel Bluetooth AX210
9e96e50 linux-firmware: Update firmware file for Intel Bluetooth AX200
c8d0db5 linux-firmware: Update firmware file for Intel Bluetooth AX201
5e2a387 Merge tag 'iwlwifi-fw-2021-03-05-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware into main
b0d3e31 rtw88: 8822c: Update normal firmware to v9.9.6
5a2fd63 iwlwifi: add new FWs from core59-66 release
4f54906 iwlwifi: update 9000-family firmwares
11b7607 iwlwifi: update 7265D firmware
e425f76 Merge branch 'add-silabs-wf200' of github.com:jerome-pouiller/linux-firmware into main
5ecd13f Mellanox: Add new mlxsw_spectrum firmware xx.2008.2406
58fb90a linux-firmware: add frimware for mediatek bluetooth chip (MT7921)
e576a1b rtw89: 8852a: add firmware v0.9.12.2
048a7cb WHENCE: add missing symlink for BananaPi M3
aa6c6e7 Add symlink for BananaPi M2 to brcmfmac43430-sdio config
58825f7 brcm: Fix Raspberry Pi 4B NVRAM file
520f71b silabs: add new firmware for WF200
f7915a0 amdgpu: add initial firmware for green sardine
80cb579 rtw88: RTL8822C: Update normal firmware to v9.9.5
b79d239 (tag: 20210208) Merge branch 'DG1-guc-huc-ADLS-dmc' of git://anongit.freedesktop.org/drm/drm-firmware into main
66970e1 Merge branch 'qcom-rb5' of https://github.com/lumag/linux-firmware into main
cf6fc2b Mellanox: Add new mlxsw_spectrum firmware xx.2008.2304
391fd50 linux-firmware: add firmware for MT7921
c5e3240 rtw88: RTL8821C: Update firmware to v24.8
d33d2d8 linux-firmware: Update firmware file for Intel Bluetooth AX210
3027ae4 linux-firmware: Update firmware file for Intel Bluetooth AX200
13979c3 linux-firmware: Update firmware file for Intel Bluetooth AX201
348d8a9 i915: Add DMC v2.01 for ADL-S
f33f1f7 i915: Add HuC v7.7.1 for DG1
6a422f5 i915: Add GuC v49.0.1 for DG1
df822a8 qcom: Add venus firmware files for VPU-1.0
11a1db1 qcom: Add SM8250 Compute DSP firmware
e55248b qcom: Add SM8250 Audio DSP firmware
da74cc6 qcom: add firmware files for Adreno a650
0578970 brcm: Link RPi4's WiFi firmware with DMI machine name.
d528862 brcm: Add NVRAM for Vamrs 96boards Rock960
870b805 brcm: Update Raspberry Pi 3B+/4B NVRAM for downstream changes
a28a590 cypress: Fix link direction
060ad8b cypress: Link the new cypress firmware to the old brcm files
0f0aefd brcm: remove old brcm firmwares that have newer cypress variants
f580dc2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x059A_25CB
7df2220 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099a_7253
e79405d rtl_bt: Add firmware and config files for RTL8852A BT USB chip
ef3813d rtl_bt: Update RTL8821C BT(USB I/F) FW to 0x829a_7644
646f159 (tag: 20201218) make AP6212 in bananpi m2 plus/zero work
28185ec linux-firmware: Update firmware file for Intel Bluetooth AX210
23da869 linux-firmware: Update firmware file for Intel Bluetooth AX200
2099248 linux-firmware: Update firmware file for Intel Bluetooth AX201
94de5e2 linux-firmware: Update firmware file for Intel Bluetooth 9560
27a3689 linux-firmware: Update firmware file for Intel Bluetooth 9260
5c3c4af Merge branch 'lt9611uxc' of https://github.com/lumag/linux-firmware into main
aaed4a8 Merge branch 'v1.1.6' of https://github.com/irui-wang/linux_fw_vpu_v1.1.6 into main
d8c9865 Merge branch 'master' of https://github.com/sampnimm/linux-firmware-BT into main
63ab3db linux-firmware: add firmware for Lontium LT9611UXC DSI to HDMI bridge
0fe0fe0 mediatek: update MT8173 VPU firmware to v1.1.6
1a08ec9 QCA : Updated firmware files for WCN3991
7455a36 Merge branch 'guc_v49' of git://anongit.freedesktop.org/drm/drm-firmware into main
7eb7fda linux-firmware: Update firmware file for Intel Bluetooth AX210
5cbf459 linux-firmware: Update firmware file for Intel Bluetooth AX210
c487f7d i915: Add GuC firmware v49.0.1 for all platforms
d9ffb07 i915: Remove duplicate KBL DMC entry
b362fd4 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2018
bc9cd0b linux-firmware: Update AMD SEV firmware
54c797a amdgpu: add sienna cichlid firmware for 20.45
1340e9c amdgpu: update vega20 firmware for 20.45
b260c9c amdgpu: update vega12 firmware for 20.45
d683bd5 amdgpu: update vega10 firmware for 20.45
7c81cc2 amdgpu: update renoir firmware for 20.45
3619e57 amdgpu: update navi14 firmware for 20.45
68ce0fb amdgpu: update navi12 firmware for 20.45
e889b80 amdgpu: update navi10 firmware for 20.45
f4edc15 amdgpu: update raven2 firmware for 20.45
e71210f amdgpu: update raven firmware for 20.45

[1] https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/commit/?id=0f0aefd733f70beae4c0246edbd2c158d5ce974c

[2] eeda8652f1/package/firmware/cypress-firmware/Makefile (L124)

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2021-06-06 00:26:13 +02:00
Robert Marko
b126d9c3a3 ipq40xx: add netgear wac510 support
This adds support for the Netgear WAC510 Insight Managed Smart Cloud
Wireless Access Point, an indoor dual-band, dual-radio 802.11ac
business-class wireless AP with integrated omnidirectional antennae
and two 10/100/1000 Mbps Ethernet ports.

For more information see:
<https://www.netgear.com/business/wifi/access-points/wac510>

Specifications:
SoC:        Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:        256 MiB
Flash1:     2 MiB Winbond W25Q16JV SPI-NOR
Flash2:     128 MiB Winbond W25N01GVZEIG SPI-NAND
Ethernet:   Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port,
            WAN port active IEEE 802.3af/at PoE in
Wireless1:  Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
Wireless2:  Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae
Input:      (Optional) Barrel 12 V 2.5 A Power, Reset button SW1
LEDs:       Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN
Serial:     Header J2
1 - 3.3 Volt (Do NOT connect!)
2 - TX
3 - RX
4 - Ground
WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter!
         The Serial settings are 115200-8-N-1.

Installation via Stock Web Interface:
BTW: The default factory console/web interface login user/password are
admin/password.

In the web interface navigating to Management - Maintenance - Upgrade -
'Firmware Upgrade' will show you what is currently installed e.g.:
Manage Firmware
Current Firmware Version: V5.0.10.2
Backup Firmware Version: V1.2.5.11
Under 'Upgrade Options' choose Local (alternatively SFTP would be
available) then click/select 'Browse File' on the right side, choose
openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar
and hit the Upgrade button below. After a minute or two your browser
should indicate completion printing 'Firmware update complete.' and
'Rebooting AP...'.

Note that OpenWrt will use the WAN PoE port as actual WAN port
defaulting to DHCP client but NOT allowing LuCI access, use LAN port
defaulting to 192.168.1.1/24 to access LuCI.

Installation via TFTP Requiring Serial U-Boot Access:
Connect to the device's serial port and hit any key to stop autoboot.
Upload and boot the initramfs based OpenWrt image as follows:
(IPQ40xx) # setenv serverip 192.168.1.1
(IPQ40xx) # setenv ipaddr 192.168.1.2
(IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb
(IPQ40xx) # bootm

Note: This only runs OpenWrt from RAM and has not installed anything
to flash as of yet. One may permanently install OpenWrt as follows:

Check the MTD device number of the active partition:
root@OpenWrt:/# dmesg | grep 'set to be root filesystem'
[    1.010084] mtd: device 9 (rootfs) set to be root filesystem
Upload the factory image ending with .ubi to /tmp (e.g. using scp or
tftp). Then flash the image as follows (substituting the 9 in mtd9
below with whatever number reported above):
root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi
And reboot.

Dual Image Configuration:
The default U-Boot boot command bootipq uses the U-Boot environment
variables primary/secondary to decide which image to boot. E.g.
primary=0, secondary=3800000 uses rootfs while primary=3800000,
secondary=0 uses rootfs_1.
Switching their values changes the active partition. E.g. from within
U-Boot:
(IPQ40xx) # setenv primary 0
(IPQ40xx) # setenv secondary 3800000
(IPQ40xx) # saveenv
Or from a OpenWrt userspace serial/SSH console:
fw_setenv primary 0
fw_setenv secondary 3800000
Note that if you install two copies of OpenWrt then each will have its
independent configuration not like when switching partitions on the
stock firmware.
BTW: The kernel log shows which boot partition is active:
[    2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB)
vs.
[    2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB)
Note: After 3 failed boot attempts it automatically switches partition.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[squashed netgear-tar commit into main and rename netgear-tar for
now, until it is made generic.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-06-05 23:29:46 +02:00
Felix Fietkau
d76535c45e wireless-regdb: update to version 2021.04.21
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-26 11:48:14 +02:00
Hauke Mehrtens
1903233f2b treewide: Mark packages nonshared if they depend on @TARGET_
This marks all packages which depend on a target with @TARGET nonshared.
If they are not marked nonshared they would be build by the SDK build
and if this happens with a different SDK, then the SDK from the target
the package depends on, the package would not be added to the index.

This should fix the image builder for some of these packages.

This should fix the image builder at least for bcm27xx/bcm2710 and
bcm4908/generic.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-05-24 00:28:22 +02:00
Roger Pueyo Centelles
d1f1e5269e ipq40xx: add support for MikroTik SXTsq 5 ac
This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD),
an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet
port.

Specifications:
 - SoC: Qualcomm Atheros IPQ4018
 - RAM: 256 MB
 - Storage: 16 MB NOR
 - Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae
 - Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in
 - 1x Ethernet LED (green)
 - 7x user-controllable LEDs
  · 1x power (blue)
  · 1x user (green)
  · 5x rssi (green)

Note:
 Serial UART is probably available on the board, but it has not been
 tested.

Flashing:
 Boot via TFTP the initramfs image. Then, upload a sysupgrade image
 via SSH and flash it normally. More info at the "Common procedures
 for MikroTik products" page https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2021-04-29 10:55:07 +02:00
Josef Schlehofer
b265649085 linux-firmware: ath10k: add support for Qualcomm Atheros QCA9377
Add firmware and board file for Qualcomm Atheros QCA9377 802.11ac Wireless
Network Adapter (rev 31) recognized as [168c:0042].

This card supports standard 1x1 802.11ac Wave2, BT5, and MU-MIMO.

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2021-04-17 21:56:05 +02:00
Robert Marko
faea7becaf
ipq40xx: add MikroTik hAP ac2 support
This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC
(hAP ac²), a  indoor dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional antennae, USB port and  five
10/100/1000 Mbps Ethernet ports.

See https://mikrotik.com/product/hap_ac2 for more info.

Specifications:
 - SoC: Qualcomm Atheros IPQ4018
 - RAM: 128 MB
 - Storage: 16 MB NOR
 - Wireless:
   · Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
   · Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
 - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port,
             passive PoE in
- 1x USB Type A port

Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-04-05 04:13:28 +02:00
Daniel Golle
ebcb4f1d0a
treewide: fix spelling 'seperate' -> 'separate'
This popular spelling mistake was also introduced by myself lately.
Fix it everywhere.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-28 23:59:21 +00:00
David Bauer
9a9cf40dd9 download: add mirror alias for Debian
Add an alias for Debian packages and download them from the Debian
mirror redirector.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-26 20:41:00 +01:00
Adrian Schmutzler
910b5d669f tfa-layerscape: build fiptool again
The ls-ddr-phy package needs fiptool options that are not
available via the version from arm-trusted-firmware-tools.
This breaks build for layerscape with the recently added LX2160a:

  create: unrecognized option '--ddr-immem-udimm-1d'

Use the tfa-layerscape variant again for now, but rename it to
fiptool-layerscape to indicate that it's a specific variant.

This reverts 84bc7d31e0 ("tfa-layerscape: don't build fiptool").

Fixes: f59d7aab2a ("layerscape: add ddr-phy package")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-21 00:01:36 +01:00
Yangbo Lu
80dcd14abe layerscape: add LX2160ARDB (Rev2.0 silicon) board support
The QorIQ LX2160A reference design board provides a comprehensive platform
that enables design and evaluation of the LX2160A processor.

- Enables network intelligence with the next generation Datapath (DPPA2)
  which provides differentiated offload and a rich set of IO, including
  10GE, 25GE, 40GE, and PCIe Gen4

- Delivers unprecedented efficiency and new virtualized networks

- Supports designs in 5G packet processing, network function
  virtualization, storage controller, white box switching, network
  interface cards, and mobile edge computing

- Supports all three LX2 family members (16-core LX2160A; 12-core LX2120A;
  and 8-core LX2080A)

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[use AUTORELEASE, add dtb to firmware part]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-19 15:29:46 +01:00
Yangbo Lu
f59d7aab2a layerscape: add ddr-phy package
Add ddr-phy package for layerscape. Currently only LX2160ARDB
requires the package.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[use AUTORELEASE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-19 15:27:45 +01:00
Yangbo Lu
2c2d77bd3b layerscape: add FRWY-LS1046A board support
The LS1046A Freeway board (FRWY) is a high-performance computing,
evaluation, and development platform that supports the QorIQ
LS1046A architecture processor capable of support more than 32,000
CoreMark performance. The FRWY-LS1046A board supports the QorIQ
LS1046A processor, onboard DDR4 memory, multiple Gigabit Ethernet,
USB3.0 and M2_Type_E interfaces for Wi-Fi.

The FRWY-LS1046A-TP includes the Coral Tensor Flow Processing Unit
that offloads AI/ML inferencing from the CPU to provide significant
boost for AI/ML applications. The FRWY-LS1046A-TP includes one M.2
TPU module and more modules can easily be added including USB
versions of the module to scale the AI/ML performance.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[rebase, use AUTORELEASE, fix sorting, add dtb to firmware part]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-19 15:27:15 +01:00
Álvaro Fernández Rojas
7febba3e50 cypress-firmware: fix PKG_SOURCE_URL
Download link has been moved.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-19 11:06:23 +01:00
Paul Spooren
8286f3a3d3 treewide: unify OpenWrt hosted source via @OPENWRT
Multiple sources are hosted on OpenWrts source server only. The source
URLs to point to the server vary based on different epochs in OpenWrts
history.

Replace all by @OPENWRT which is an "empty" mirror, therefore using the
fallback servers sources.cdn.openwrt.org and sources.openwrt.org.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-02-05 12:00:24 -10:00
Robert Marko
246fd27e52 linux-firmware: Add wil6210 firmware
This patch adds wil6210 firmware and board files.
Firmware version is not up to date but is only freely redistributable one I found.
Board file is a generic one so most devices and especially those for long distance
PtP links will require so in a ipq-wifi like way.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-01-05 02:16:24 +00:00
Álvaro Fernández Rojas
e1938d3397 ath10k-ct-firmware: update to 022 (2020-11-08)
Runtime-tested on ath79 (TP-Link Archer C7 v2) and ipq806x (Netgear R7800).

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-12-28 18:07:34 +01:00
Dongming Han
b9389186b0 ipq40xx: add support for GL.iNet GL-AP1300
Specifications:
SOC:        Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:        256 MiB
FLASH1:     4 MiB NOR
FLASH2:     128 MiB NAND
ETH:        Qualcomm QCA8075
WLAN1:      Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2:      Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT:      Reset
LED:        Power, Internet
UART1:      On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
OTHER:      On board with BLE module - by cp210x USB serial chip
            On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed

Install via uboot tftp or uboot web failsafe.

By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi
(IPQ40xx) # run lf

By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1

Afterwards upgrade can use sysupgrade image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
2020-12-25 10:38:13 +01:00
Yanase Yuki
3bb1618573 ipq806x: add support for NEC Platforms Aterm WG2600HP3
NEC Platforms Aterm WG2600HP3 is a dual-band router based on Qualcomm IPQ8062.

Specification
-------------
- SoC: Qualcomm IPQ8062
- RAM: 512MiB
- Flash memory: SPI-NOR 32MiB (Cypress S25FL256S)
- Wi-Fi: Qualcomm QCA9984 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm QCA9984 (5GHz, 36ch - 64ch, 100ch - 140ch)
- Ethernet: 4x 100/1000 Mbps (1x WAN, 4x LAN)
- LED: 6x green LED, 6x red LED
- Input: 2x tactile switch, 1x SP3T slide switch
- Serial console: 115200bps, through-hole J3
  - [  ] [GND] [  ] [TX] [RX] ----> DC jack
- Power: DC 12V 1.5A

This device does not support VHT160 and VHT80+80.
Custom BDFs are required to limit VHT capabilities.

Flash instructions
------------------
1. Setup TFTP server (IP address: 192.168.1.2)
2. Put initramfs image into TFTP server directory
3. Connect WG2600HP3 lan port and computer that runs TFTP server
4. Connect to the serial console
5. Interrupt booting by Esc key (password: chiron)
6. Execute the following commands
    # setenv bootcmd "nboot 0x44000000 1 0x860000"
    # saveenv
    # setenv ipaddr 192.168.1.1
    # setenv serverip 192.168.1.2
    # tftpboot 0x44000000 openwrt-ipq806x-generic-nec_wg2600hp3-initramfs-uImage
7. After booting OpenWrt initramfs image, backup SPI-NOR flash memory
8. Erase firmware partition
    # mtd erase firmware
9. Run sysupgrade

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
2020-12-25 10:38:13 +01:00
Sven Eckelmann
b4009f453c ipq-wifi: Fix suffix for Plasma Cloud PA2200 QCA4019 board-2.bin
The Makefile is rejecting all files with for a given prefix (here
"board-plasmacloud_pa2200") when it didn't match a known suffix. Instead it
stops the build with an error like:

  Makefile:135: *** Unrecognized board-file suffix '.ipq4019' for 'board-plasmacloud_pa2200.ipq4019'. Stop.

The correct suffix for the QCA4019/hw1.0 is qca4019 and not ipq4019.

Fixes: 4871fd2616 ("ipq40xx: add support for Plasma Cloud PA2200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-25 10:38:13 +01:00
Sven Eckelmann
1c557e27fd ipq-wifi: Fix suffix for Plasma Cloud PA1200 QCA4019 board-2.bin
The Makefile is rejecting all files with for a given prefix (here
"board-plasmacloud_pa1200") when it didn't match a known suffix. Instead it
stops the build with an error like:

  Makefile:135: *** Unrecognized board-file suffix '.ipq4019' for 'board-plasmacloud_pa1200.ipq4019'. Stop.

The correct suffix for the QCA4019/hw1.0 is qca4019 and not ipq4019.

Fixes: ea5bb6bbfe ("ipq40xx: add support for Plasma Cloud PA1200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-25 10:38:13 +01:00
Stefan Schake
d3c8881194 ipq40xx: add support for devolo Magic 2 WiFi next
SOC:     IPQ4018 / QCA Dakota
CPU:     Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7
DRAM:    256 MiB
NOR:     32 MiB
ETH:     Qualcomm Atheros QCA8075 (2 ports)
PLC:     MaxLinear G.hn 88LX5152
WLAN1:   Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:   Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:   RESET, WiFi, PLC Button
LEDS:    red/white home, white WiFi

To modify a retail device to run OpenWRT firmware:
1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT
   initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'.
2) Power on the device while pressing the recessed reset button next to
   the Ethernet ports. This causes the bootloader to retrieve and start
   the initramfs.
3) Once the initramfs is booted, the device will come up with IP
   192.168.1.1. You can then connect through SSH (allow some time for
   the first connection).
4) On the device shell, run 'fw_printenv' to show the U-boot environment.
   Backup this information since it contains device unique factory data.
5) Change the boot command to support booting OpenWRT:
   # fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm'
6) Change directory to /tmp, download the sysupgrade (e.g. through wget)
   and install it with sysupgrade. The device will reboot into OpenWRT.

Notice that there is currently no support for booting the G.hn chip.
This requires userland software we lack the rights to share right now.

Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
2020-12-22 20:55:40 +01:00
Marek Lindner
4871fd2616 ipq40xx: add support for Plasma Cloud PA2200
Device specifications:

* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 36-64)
  - QCA9888 hw2.0 (PCI)
  - requires special BDF in QCA9888/hw2.0/board-2.bin
    bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 100-165)
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200
* GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE
* GPIO-LEDs for power (orange) and status (blue)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio3:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + used as LAN interface
  - phy@mdio4:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 802.3at POE+
    + used as WAN interface
* 12V 2A DC

Flashing instructions:

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-22 19:11:50 +01:00
Marek Lindner
ea5bb6bbfe ipq40xx: add support for Plasma Cloud PA1200
Device specifications:

* QCA IPQ4018
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200
* 2T2R 5 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200
* 3x GPIO-LEDs for status (cyan, purple, yellow)
* 1x GPIO-button (reset)
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio4:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + used as LAN interface
  - phy@mdio3:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 802.3af/at POE(+)
    + used as WAN interface
* 12V/24V 1A DC

Flashing instructions:

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-22 19:11:50 +01:00
Hauke Mehrtens
94d1b2508c wireless-regdb: Update to version 2020.11.20
9efa1da wireless-regdb: update regulatory rules for Egypt (EG)
ede87f5 wireless-regdb: restore channel 12 & 13 limitation in the US
5bcafa3 wireless-regdb: Update regulatory rules for Croatia (HR)
4e052f1 wireless-regdb: Update regulatory rules for Pakistan (PK) on 5GHz
f9dfc58 wireless-regdb: update 5.8 GHz regulatory rule for GB
c19aad0 wireless-regdb: Update regulatory rules for Kazakhstan (KZ)
07057d3 wireless-regdb: update regulatory database based on preceding changes

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-12-16 22:11:19 +01:00
Álvaro Fernández Rojas
61e381d322 ath10k-firmware: remove unused package
All firmwares were added to linux-firmware, so there's no need to keep this
package definitions.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-11-28 18:19:37 +01:00
Álvaro Fernández Rojas
655091ec45 ath10k-ct-firmware: switch to linux-firmware board binaries
Instead of duplicating board firmware binaries, which are exactly the same
as the ones from linux-firmware, add dependencies and remove duplicated
downloads.

Runtime-tested on ath79 (TP-Link Archer C7 v2) and ipq806x (Netgear R7800).

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-11-28 18:19:37 +01:00
Álvaro Fernández Rojas
c3b2efaf24 linux-firmware: ath10k: add board firmware packages
Split ath10k firmwares into board and firmware packages.
This way we can add dependencies to ath10k-ct firmware packages.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-11-28 18:19:37 +01:00
Álvaro Fernández Rojas
2418657104 linux-firmware: brcm: use RPI 4B NVRAM file
Use the dedicated RPI 4B NVRAM file introduced in 20191215.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-11-25 10:46:15 +01:00
Álvaro Fernández Rojas
3c0059773c cypress-nvram: add proper package conflicts
There are linux firmware packages for all RPIs NVRAMs.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-11-25 10:30:44 +01:00
Álvaro Fernández Rojas
3678778445 cypress-firmware: add proper package conflicts
There are linux firmwares packages for 43362, 43430 and 43455 which shouldn't
be installed at the same time as Cypress firmwares.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-11-25 10:30:44 +01:00
Karel Kočí
bbe302d2b6 ath10k-ct-firmware: add conflicts and better provides
This expands packages to define not only provides but also conflicts.
These packages provides same files so they should specify conflicts.

Second expansion is that *-ct-htt and *-ct-full-htt firmwares can also
provide *-ct variant as that allows explicit dependency on CT variant
with various firmware modifications.

Signed-off-by: Karel Kočí <karel.koci@nic.cz>
[Bump PKG_RELEASE and format PROVIDES/CONFLICTS]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-11-25 10:30:44 +01:00
Pawel Dembicki
cdff729b27 layerscape: enable spi-uart in LS1012A-FRDM
This patch add missing support of SC16IS740 serial controller, installed
on LS1012A-FRDM board.

It was required to change RCW bits, because SPI was disabled by default.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-11-23 22:53:15 +01:00
John Audia
991e6f8ccc linux-firmware: update to 20201118
git log --pretty=oneline --abbrev-commit 20201022..20201118
2ea8667 (tag: 20201118) rtlwifi: v88.2 firmware files for RTL8192CU
e850cf3 Merge https://github.com/rjliao-qca/qca-btfw into main
65370db rtw88: RTL8822C: Update firmware to v9.9.4
e371b7c Revert "rtw88: RTL8822C: Update firmware to v9.9.4"
51d2c81 vpdma: Move firmware to ti directory
d7a24c9 Merge branch 'master' of https://github.com/shahasit/video-linux-firmware into main
9ee1543 Merge branch 'master' of https://github.com/shahasit/bt-linux-firmware into main
3bcc4c1 amdgpu: update picasso VCN firmware
b6b4542 amdgpu: update raven2 VCN firmware
79aa335 amdgpu: update raven VCN firmware
c93834e rtw88: RTL8822C: Update firmware to v9.9.4
3ef6c93 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099A_281A
b503c96 Merge branch 'ath10k-20201023' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/linux-firmware into main
463fdea QCA: Update Bluetooth firmware for QCA6390
8a46c32 qcom : updated venus firmware files for v5.4
d7793e5 QCA : Fixed BT SSR due to command timeout / IO fatal error
d842d8c ath11k: QCA6390 hw2.0: add to WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
8fb1a6e ath11k: QCA6390 hw2.0: add board-2.bin
34cb5fc ath11k: IPQ8074 hw2.0: add to WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
c0a8efd ath11k: IPQ8074 hw2.0: add board-2.bin
ac7f5e9 ath11k: IPQ6018 hw1.0: add to WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
2594e51 ath11k: IPQ6018 hw1.0: add board-2.bin
d8f10d4 ath10k: QCA6174 hw3.0: add firmware-sdio-6.bin version WLAN.RMH.4.4.1-00077
6652297 ath10k: QCA9984 hw1.0: update firmware-5.bin to 10.4-3.9.0.2-00131
36059aa ath10k: QCA9888 hw2.0: update firmware-5.bin to 10.4-3.9.0.2-00131
1e5629d ath10k: QCA6174 hw3.0: update board-2.bin
e315d1a ath10k: QCA6174 hw3.0: update firmware-6.bin to WLAN.RM.4.4.1-00157-QCARMSWPZ-1

Signed-off-by: John Audia <graysky@archlinux.us>
2020-11-23 22:53:15 +01:00
John Audia
e48aac89a2 linux-firmware: update to 20201022
git log --pretty=oneline --abbrev-commit 20200918..20201022
dae4b4c (HEAD -> main, tag: 20201022, origin/master, origin/main, origin/HEAD) Merge branch 'v1.1.5' of https://github.com/irui-wang/linux_fw_vpu_v1.1.5 into main
04f71fe cypress: add Cypress firmware and clm_blob files
4d0755b Merge https://github.com/shahasit/bt-linux-firmware into main
2a262bb Merge https://github.com/shahasit/video-linux-firmware into main
c024640 Merge tag 'iwlwifi-fw-2020-10-14' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware into main
09e8cff rtl_bt: Update RTL8821C BT FW to 0xAA6C_A99E
d7904d5 ath10k: add SDIO firmware for QCA9377 WiFi
ecdc272 Merge branch 'dg1_dmc_v2_02' of git://anongit.freedesktop.org/drm/drm-firmware into main
c86361d ice: update package file to 1.3.16.0
76ceac8 mediatek: separate venc service thread
8877322 QCA : Updated firmware file for WCN3991
4f41e9d iwlwifi: update and add new FWs from core56-54 release
346057d iwlwifi: update 3168, 7265D, 8000C and 8265 firmwares
a140ef3 i915: Add DG1 DMC v2.02
a09b728 qcom : updated venus firmware files for v5.4
58d41d0 ice: Add comms package file for Intel E800 series driver
c1bef9e copy-firmware: Always write Link: entries
b95e230 Merge commit 'ad1da95d52f1a9206da3ef52f3484f3b89ec6615' of https://github.com/shahasit/linux-firmware-bt into main
0b884ec amdgpu: update vega20 firmware for 20.40
bca0233 amdgpu: update vega12 firmware for 20.40
8652e02 amdgpu: update vega10 firmware for 20.40
9f46d48 amdgpu: update renoir firmware for 20.40
e667605 amdgpu: update raven2 firmware for 20.40
a487f2f amdgpu: update raven firmware for 20.40
aa7b732 amdgpu: update picasso firmware for 20.40
a18981e amdgpu: update navi14 firmware for 20.40
1696e2e amdgpu: update navi12 firmware for 20.40
6b8a6ea amdgpu: update navi10 firmware for 20.40
5b30b38 linux-firmware: Add new VPDMA firmware 1b8.bin
ad1da95 QCA : Updated firmware files for WCN3991
b78a66c linux-firmware: Update firmware for Cadence MHDP8546 DP bridge
afbfb5f linux-firmware: Update firmware patch for Intel Bluetooth 7265 (D1)
a38b8ed Mellanox: Add new mlxsw_spectrum firmware xx.2008.1312
1487a8a linux-firmware: nvidia: move firmware symlinks to WHENCE
bdd5617 linux-firmware: move i915 firmware symlinks to WHENCE
ab69b57 linux-firmware: move iwlwifi-7265D-10.ucode symlink to WHENCE
49c4ff5 Merge branch 'mrvl-prestera' of https://github.com/PLVision/linux-firmware into main
7a02212 linux-firmware: Update Marvell Switchdev firmware with ABI changes

Signed-off-by: John Audia <graysky@archlinux.us>
2020-11-01 20:54:37 +01:00
Biwen Li
348602186a layerscape: update ls-rcw to LSDK-20.04-update-290520
Update ls-rcw to LSDK-20.04-update-290520.

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[rebase, fix PKG_RELEASE change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-26 00:40:12 +01:00
Sungbo Eo
8f29e36963 ipq40xx: improve support for Edgecore ECW5211
This adds several stylistic and functional improvements of the recently
added Edgecore ECW5211, especially:

* Drop the local BDFs as those are already in the upstream under different names
* Add SPDX tag to DTS
* Add label MAC address
* Move LED trigger to DTS
* Remove unnecessary status="okay"
* Disable unused SS USB phy as the USB port only supports USB 2.0
* Make uboot-env partition writable
* Remove qcom,poll_required_dynamic property as the driver does not use it
* Tidy up the device recipe

Fixes: 4488b260a0 ("ipq40xx: add Edgecore ECW5211 support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Acked-by: Robert Marko <robert.marko@sartura.hr>
2020-10-07 18:07:54 +02:00
David Bauer
0abf2c081c linux-firmware: update to 20200918
00a84c5 linux-firmware: Update AMD SEV firmware
71338c2 Merge branch 'for-master' of https://github.com/CosmicPenguin/linux-firmware into main
07367b9 linux-firmware: Update firmware file for Intel Bluetooth AX200
1d1586a linux-firmware: Update firmware file for Intel Bluetooth AX201
28b333d linux-firmware: Update firmware file for Intel Bluetooth 9560
db30380 linux-firmware: Update firmware file for Intel Bluetooth 9260
eb3aa1f Mellanox: Add new mlxsw_spectrum firmware xx.2008.1310
ec88f05 mediatek: update MT7915 firmware to 20200819
a9993f8 brcm: Fix a stale symlink for RPi3 model b+
f48fec4 qcom: Add updated a5xx and a6xx microcode
d5f9eea wl18xx: update firmware file 8.9.0.0.83
7a237c6 linux-firmware: mt7615: update firmware to 20200814 version
74bd44f amdgpu: add navi12 firmware from 20.30
b9f69cd amdgpu: update navi10 firmware for 20.30

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-10-03 22:51:16 +02:00
David Bauer
f29c7a1f30 ath10k-firmware: package Wave1 from linux-firmware
The firmware for Wave1 chips was updated to the latest release
10.2.4-1.0-00047 at the end of 2019 (commit 513d70cc50b).
Package firmware for these chips from linux-firmware.

This avoids downloading the ath10k-firmware repository.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-09-28 16:23:33 +02:00
Hans Geiblinger
a9071d02b5 ipq40xx: Add support for Linksys MR8300 (Dallas)
The Linksys MR8300 is based on QCA4019 and QCA9888
and provides three, independent radios.
NAND provides two, alternate kernel/firmware images
with fail-over provided by the OEM U-Boot.

Hardware Highlights:

SoC: IPQ4019 at 717 MHz (4 CPUs)
RAM: 512MB RAM

SoC:	Qualcomm IPQ4019 at 717 MHz (4 CPUs)
RAM:	512M DDR3
FLASH:	256 MB NAND (Winbond W29N02GV, 8-bit parallel)
ETH:	Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks)
BTN:	Reset and WPS
USB:	USB3.0, single port on rear with LED
SERIAL:	Serial pads internal (unpopulated)
LED:	Four status lights on top + USB LED
WIFI1:	2x2:2 QCA4019 2.4 GHz radio on ch. 1-14
WIFI2:  2x2:2 QCA4019 5 GHz radio on ch. 36-64
WIFI3:  2x2:2 QCA9888 5 GHz radio on ch. 100-165

Support is based on the already supported EA8300.
Key differences:
	EA8300 has 256MB RAM where MR8300 has 512MB RAM.
	MR8300 has a revised top panel LED setup.

Installation:
"Factory" images may be installed directly through the OEM GUI using
URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1)

Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com>
[copied Hardware-highlights from EA8300. Fixed alphabetical order.
fixed commit subject, removed bogus unit-address of keys,
fixed author (used Signed-off-By to From:) ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:31:51 +02:00
Tomasz Maciej Nowak
e24635710c ipq40xx: add support for Luma Home WRTQ-329ACN
Luma Home WRTQ-329ACN, also known as Luma WiFi System, is a dual-band
wireless access point.

Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 2 MB SPI NOR
       128 MB SPI NAND
WIFI: 2.4 GHz 2T2R integrated
      5 GHz 2T2R integrated
Ethernet: 2x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
Bluetooth: 1x 4.0 CSR8510 A10, connected to USB bus
LEDS: 16x multicolor LEDs ring, controlled by MSP430G2403 MCU
Buttons: 1x GPIO controlled
EEPROM: 16 Kbit, compatible with AT24C16
UART: row of 4 holes marked on PCB as J19, starting count from the side
      of J19 marking on PCB
      1. GND, 2. RX, 3. TX, 4. 3.3V
      baud: 115200, parity: none, flow control: none

The device supports OTA or USB flash drive updates, unfotunately they
are signed. Until the signing key is known, the UART access is mandatory
for installation. The difficult part is disassembling the casing, there
are a lot of latches holding it together.

Teardown
Prepare three thin, but sturdy, prying tools. Place the device with back
of it facing upwards. Start with the wall having a small notch. Insert
first tool, until You'll feel resistance and keep it there. Repeat the
procedure for neighbouring walls. With applying a pressure, one edge of
the back cover should pop up. Now carefully slide one of the tools to
free the rest of the latches.
There's no need to solder pins to the UART holes, You can use hook clips,
but wiring them outside the casing, will ease debuging and recovery if
problems occur.

Installation
1. Prepare TFTP server with OpenWrt initramfs image.
2. Connect to UART port (don't connect the voltage pin).
3. Connect to LAN port.
4. Power on the device, carefully observe the console output and when
   asked quickly enter the failsafe mode.
5. Invoke 'mount_root'.
6. After the overlayfs is mounted run:
     fw_setenv bootdelay 3
   This will allow to access U-Boot shell.
7. Reboot the device and when prompted to stop autoboot, hit any key.
8. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
   'setenv' to do that, then run following commands:
     tftpboot 0x84000000 <openwrt_initramfs_image_name>
     bootm 0x84000000
   and wait till OpenWrt boots.
9. In OpenWrt command line run following commands:
     fw_setenv openwrt "setenv mtdids nand1=spi_nand; setenv mtdparts mtdparts=spi_nand:-(ubi); ubi part ubi; ubi read 0x84000000 kernel; bootm 0x84000000"
     fw_setenv bootcmd "run openwrt"
10. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
    with:
     ubirmvol /dev/ubi0 -N ubi_rootfs
     sysupgrade -v -n /tmp/<openwrt_sysupgrade_image_name>
11. After flashing, the access point will reboot to OpenWrt, then it's
    ready for configuration.

Reverting to OEM firmware
1. Execute installation guide steps: 1, 2, 3, 7, 8.
2. In OpenWrt command line run following commands:
     ubirmvol /dev/ubi0 -N rootfs_data
     ubirmvol /dev/ubi0 -N rootfs
     ubirmvol /dev/ubi0 -N kernel
     ubirename /dev/ubi0 kernel1 kernel ubi_rootfs1 ubi_rootfs
     ubimkvol /dev/ubi0 -S 34 -N kernel1
     ubimkvol /dev/ubi0 -S 320 -N ubi_rootfs1
     ubimkvol /dev/ubi0 -S 264 -N rootfs_data
     fw_setenv bootcmd bootipq
3. Reboot.

Known issues
The LEDs ring doesn't have any dedicated driver or application to control
it, the only available option atm is to manipulate it with 'i2cset'
command. The default action after applying power to device is spinning
blue light. This light will stay active at all time. To disable it
install 'i2c-tools' with opkg and run:
 i2cset -y 2 0x48 3 1 0 0 i
The light will stay off until next cold boot.

Additional information
After completing 5. step from installation guide, one can disable asking
for root password on OEM firmware by running:
 sed -e 's/root/root::/' -i /etc/passwd
This is useful for investigating the OEM firmware. One can look
at the communication between the stock firmware and the vendor's
cloud servers or as a way of making a backup of both flash chips.
The root password seems to be constant across all sold devices.
This is output of 'led_ctl' from OEM firmware to illustrate
possibilities of LEDs ring:

Usage: led_ctl [status | upgrade | force_upgrade | version]
       led_ctl solid    COLOR <brightness>
       led_ctl single   COLOR INDEX <brightness 0 - 15>
       led_ctl spinning COLOR <period 1 - 16 (lower = faster)>
       led_ctl fill     COLOR <period 1 - 16 (lower = faster)>
                                             ( default is 5 )
       led_ctl flashing COLOR <on dur 1 - 128>  <off dur 1 - 128>
                              (default is  34)  ( default is 34 )
       led_ctl pulsing  COLOR
COLOR: red, green, blue, yellow, purple, cyan, white

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[squash "ipq-wifi: add BDFs for Luma Home WRTQ-329ACN" into commit,
changed ubi volumes for easier integration, slightly reworded
commit message, changed ubi volume layout to use standard names all
around]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:30:19 +02:00
Tan Zien
e826e00765 firmware: intel-microcode: update to 20200616
intel-microcode (3.20200616.1)

  * New upstream microcode datafile 20200616
    + Downgraded microcodes (to a previously shipped revision):
      sig 0x000406e3, pf_mask 0xc0, 2019-10-03, rev 0x00d6, size 101376
      sig 0x000506e3, pf_mask 0x36, 2019-10-03, rev 0x00d6, size 101376
  * Works around hangs on boot on Skylake-U/Y and Skylake Xeon E3,
  * This update *removes* the SRBDS mitigations from the above processors
  * Note that Debian had already downgraded 0x406e3 in release 3.20200609.2

intel-microcode (3.20200609.2)

  * REGRESSION FIX: 0x406e3: rollback to rev 0xd6 and document regression
    * Microcode rollbacks (closes: LP#1883002)
      sig 0x000406e3, pf_mask 0xc0, 2019-10-03, rev 0x00d6, size 101376
    * THIS REMOVES THE SECURITY FIXES FOR SKYLAKE-U/Y PROCESSORS
    * Avoid hangs on boot on (some?) Skylake-U/Y processors,
  * ucode-blacklist: blacklist models 0x8e and 0x9e from late-loading,
    just in case.  Note that Debian does not do late loading by itself.
    Refer to LP#1883002 for the report, 0x806ec hangs upon late load.

intel-microcode (3.20200609.1)

  * SECURITY UPDATE
    * For most processors: SRBDS and/or VRDS, L1DCES mitigations depending
      on the processor model
    * For Skylake HEDT and Skylake Xeons with signature 0x50654: VRDS and
      L1DCES mitigations, plus mitigations described in the changelog entry
      for package release 3.20191112.1.
    * Expect some performance impact, the mitigations are enabled by
      default.  A Linux kernel update will be issued that allows one to
      selectively disable the mitigations.
  * New upstream microcode datafile 20200609
    * Implements mitigation for CVE-2020-0543 Special Register Buffer Data
      Sampling (SRBDS), INTEL-SA-00320, CROSSTalk
    * Implements mitigation for CVE-2020-0548 Vector Register Data Sampling
      (VRDS), INTEL-SA-00329
    * Implements mitigation for CVE-2020-0549 L1D Cache Eviction Sampling
      (L1DCES), INTEL-SA-00329
    * Known to fix the regression introduced in release 2019-11-12 (sig
      0x50564, rev. 0x2000065), which would cause several systems with
      Skylake Xeon, Skylake HEDT processors to hang while rebooting
    * Updated Microcodes:
      sig 0x000306c3, pf_mask 0x32, 2019-11-12, rev 0x0028, size 23552
      sig 0x000306d4, pf_mask 0xc0, 2019-11-12, rev 0x002f, size 19456
      sig 0x00040651, pf_mask 0x72, 2019-11-12, rev 0x0026, size 22528
      sig 0x00040661, pf_mask 0x32, 2019-11-12, rev 0x001c, size 25600
      sig 0x00040671, pf_mask 0x22, 2019-11-12, rev 0x0022, size 14336
      sig 0x000406e3, pf_mask 0xc0, 2020-04-27, rev 0x00dc, size 104448
      sig 0x00050653, pf_mask 0x97, 2020-04-24, rev 0x1000157, size 32768
      sig 0x00050654, pf_mask 0xb7, 2020-04-24, rev 0x2006906, size 34816
      sig 0x00050656, pf_mask 0xbf, 2020-04-23, rev 0x4002f01, size 52224
      sig 0x00050657, pf_mask 0xbf, 2020-04-23, rev 0x5002f01, size 52224
      sig 0x000506e3, pf_mask 0x36, 2020-04-27, rev 0x00dc, size 104448
      sig 0x000806e9, pf_mask 0x10, 2020-04-27, rev 0x00d6, size 103424
      sig 0x000806e9, pf_mask 0xc0, 2020-04-27, rev 0x00d6, size 103424
      sig 0x000806ea, pf_mask 0xc0, 2020-04-27, rev 0x00d6, size 103424
      sig 0x000806eb, pf_mask 0xd0, 2020-04-27, rev 0x00d6, size 103424
      sig 0x000806ec, pf_mask 0x94, 2020-04-23, rev 0x00d6, size 103424
      sig 0x000906e9, pf_mask 0x2a, 2020-04-23, rev 0x00d6, size 103424
      sig 0x000906ea, pf_mask 0x22, 2020-04-27, rev 0x00d6, size 102400
      sig 0x000906eb, pf_mask 0x02, 2020-04-23, rev 0x00d6, size 103424
      sig 0x000906ec, pf_mask 0x22, 2020-04-27, rev 0x00d6, size 102400
      sig 0x000906ed, pf_mask 0x22, 2020-04-23, rev 0x00d6, size 103424
  * Restores the microcode-level fixes that were reverted by release
    3.20191115.2 for sig 0x50654 (Skylake Xeon, Skylake HEDT)

intel-microcode (3.20200520.1)

  * New upstream microcode datafile 20200520
    + Updated Microcodes:
      sig 0x000206d6, pf_mask 0x6d, 2020-03-04, rev 0x0621, size 18432
      sig 0x000206d7, pf_mask 0x6d, 2020-03-24, rev 0x071a, size 19456

intel-microcode (3.20200508.1)

  * New upstream microcode datafile 20200508
    + Updated Microcodes:
      sig 0x000706e5, pf_mask 0x80, 2020-03-12, rev 0x0078, size 107520
    * Likely fixes several critical errata on IceLake-U/Y causing system
      hangs

intel-microcode (3.20191115.2)

  * Microcode rollbacks (closes: #946515, LP#1854764):
    sig 0x00050654, pf_mask 0xb7, 2019-07-31, rev 0x2000064, size 33792
  * Avoids hangs on warm reboots (cold boots work fine) on HEDT and
    Xeon processors with signature 0x50654.

intel-microcode (3.20191115.1)

  * New upstream microcode datafile 20191115
    + Updated Microcodes:
      sig 0x000406e3, pf_mask 0xc0, 2019-10-03, rev 0x00d6, size 101376
      sig 0x000506e3, pf_mask 0x36, 2019-10-03, rev 0x00d6, size 101376
      sig 0x000806e9, pf_mask 0x10, 2019-10-15, rev 0x00ca, size 100352
      sig 0x000806e9, pf_mask 0xc0, 2019-09-26, rev 0x00ca, size 100352
      sig 0x000806ea, pf_mask 0xc0, 2019-10-03, rev 0x00ca, size 100352
      sig 0x000806eb, pf_mask 0xd0, 2019-10-03, rev 0x00ca, size 100352
      sig 0x000806ec, pf_mask 0x94, 2019-10-03, rev 0x00ca, size 100352
      sig 0x000906e9, pf_mask 0x2a, 2019-10-03, rev 0x00ca, size 100352
      sig 0x000906ea, pf_mask 0x22, 2019-10-03, rev 0x00ca, size 99328
      sig 0x000906eb, pf_mask 0x02, 2019-10-03, rev 0x00ca, size 100352
      sig 0x000906ec, pf_mask 0x22, 2019-10-03, rev 0x00ca, size 99328
      sig 0x000906ed, pf_mask 0x22, 2019-10-03, rev 0x00ca, size 100352
      sig 0x000a0660, pf_mask 0x80, 2019-10-03, rev 0x00ca, size 91136

intel-microcode (3.20191113.1)

  * New upstream microcode datafile 20191113
    + SECURITY UPDATE, refer to the 3.20191112.1 changelog entry for details
      Adds microcode update for CFL-S (Coffe Lake Desktop)
      INTEL-SA-00270, CVE-2019-11135, CVE-2019-0117
    + Updated Microcodes (previously removed):
      sig 0x000906ec, pf_mask 0x22, 2019-08-14, rev 0x00c6, size 99328

intel-microcode (3.20191112.1)

  * New upstream microcode datafile 20191112
    + SECURITY UPDATE
      - Implements MDS mitigation (TSX TAA), INTEL-SA-00270, CVE-2019-11135
      - Implements TA Indirect Sharing mitigation, and improves the
        MDS mitigation (VERW)
      - Fixes FIVR (Xeon Voltage Modulation) vulnerability, INTEL-SA-00271,
        CVE-2019-11139
      - Fixes SGX vulnerabilities and errata (including CVE-2019-0117)
    + CRITICAL ERRATA FIXES
      - Fixes Jcc conditional jump macro-fusion erratum (Skylake+, except
        Ice Lake), causes a 0-3% typical perforance hit (can be as bad
        as 10%).  But ensures the processor will actually jump where it
        should, so don't even *dream* of not applying this fix.
      - Fixes AVX SHUF* instruction implementation flaw erratum
    + Removed Microcodes:
      sig 0x000906ec, pf_mask 0x22, 2019-02-14, rev 0x00ae, size 98304
    + New Microcodes:
      sig 0x000406d8, pf_mask 0x01, 2019-09-16, rev 0x012d, size 84992
      sig 0x00050656, pf_mask 0xbf, 2019-09-05, rev 0x400002c, size 51200
      sig 0x00060663, pf_mask 0x80, 2018-04-17, rev 0x002a, size 87040
      sig 0x000706a8, pf_mask 0x01, 2019-08-29, rev 0x0016, size 74752
      sig 0x000706e5, pf_mask 0x80, 2019-09-05, rev 0x0046, size 102400
      sig 0x000a0660, pf_mask 0x80, 2019-08-27, rev 0x00c6, size 91136
    + Updated Microcodes:
      sig 0x000406e3, pf_mask 0xc0, 2019-08-14, rev 0x00d4, size 101376
      sig 0x00050654, pf_mask 0xb7, 2019-09-05, rev 0x2000065, size 34816
      sig 0x00050657, pf_mask 0xbf, 2019-09-05, rev 0x500002c, size 51200
      sig 0x000506e3, pf_mask 0x36, 2019-08-14, rev 0x00d4, size 101376
      sig 0x000706a1, pf_mask 0x01, 2019-08-28, rev 0x0032, size 73728
      sig 0x000806e9, pf_mask 0x10, 2019-08-14, rev 0x00c6, size 99328
      sig 0x000806e9, pf_mask 0xc0, 2019-08-14, rev 0x00c6, size 100352
      sig 0x000806ea, pf_mask 0xc0, 2019-08-14, rev 0x00c6, size 99328
      sig 0x000806eb, pf_mask 0xd0, 2019-08-14, rev 0x00c6, size 100352
      sig 0x000806ec, pf_mask 0x94, 2019-08-14, rev 0x00c6, size 100352
      sig 0x000906e9, pf_mask 0x2a, 2019-08-14, rev 0x00c6, size 100352
      sig 0x000906ea, pf_mask 0x22, 2019-08-14, rev 0x00c6, size 99328
      sig 0x000906eb, pf_mask 0x02, 2019-08-14, rev 0x00c6, size 100352
      sig 0x000906ed, pf_mask 0x22, 2019-08-14, rev 0x00c6, size 99328
    + Updated Microcodes (previously removed):
      sig 0x00050653, pf_mask 0x97, 2019-09-09, rev 0x1000151, size 32768

Signed-off-by: Tan Zien <nabsdh9@gmail.com>
2020-09-18 20:08:51 +02:00
Tan Zien
182c7d955f firmware: amd64-microcode: update to 20191218
amd64-microcode (3.20191218.1)

  * New microcode update packages from AMD upstream:
    + Removed Microcode updates (known to cause issues):
      sig 0x00830f10, patch id 0x08301025, 2019-07-11
  * README: update for new release

amd64-microcode (3.20191021.1)

  * New microcode update packages from AMD upstream:
    + New Microcodes:
      sig 0x00830f10, patch id 0x08301025, 2019-07-11
    + Updated Microcodes:
      sig 0x00800f12, patch id 0x08001250, 2019-04-16
      sig 0x00800f82, patch id 0x0800820d, 2019-04-16

amd64-microcode (3.20181128.1)

  * New microcode update packages from AMD upstream:
    + New Microcodes:
      sig 0x00800f82, patch id 0x0800820b, 2018-06-20

Signed-off-by: Tan Zien <nabsdh9@gmail.com>
2020-09-18 20:08:51 +02:00
John Crispin
0fbdb51f76 ipq40xx: add Edgecore OAP-100 support
flashing the unit
* first update to latest edcore FW as per the PDF instructions
* boot the initramfs
  - tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm
* inside the initramfs call the following commiands
  - ubiattach -p /dev/mtd0
  - ubirmvol /dev/ubi0 -n0
  - ubirmvol /dev/ubi0 -n1
  - ubirmvol /dev/ubi0 -n2
* scp the sysupgrade image to the board and call
  - sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin

Signed-off-by: John Crispin <john@phrozen.org>
2020-09-17 08:43:07 +02:00
Robert Marko
4488b260a0 ipq40xx: add Edgecore ECW5211 support
This patch adds support for the Edgecore ECW5211 indoor AP.

Specification:
- SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7
- RAM: 256MB DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB MX35LFxGE4AB SPI-NAND
- Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn)
- CC2540 BLE connected to USB 2.0 port
- Atmel AT97SC3205T I2C TPM

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-17 08:43:03 +02:00
Robert Marko
59f0a0fd83 ipq806x: add Edgecore ECW5410 support
This patch adds support for the Edgecore ECW5410 indoor AP.

Specification:
- SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15
- RAM: 256MB(225 usable) DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB S34MS01G2 Parallel NAND
- Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn)
- CC2540 BLE
- UART console on RJ45 next to ethernet ports exposed.
Its Cisco pin compatible, 115200 8n1 baud.

Installation instructions:
Through stock firmware or initramfs.

1.Connect to console
2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe.
3. Transfer factory image
4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path>

This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0

Note

Initramfs:
1.  Connect to console
2.  Transfer the image from TFTP server with tftpboot,
or by using DHCP advertised image with dhcp command.
3. bootm
4. Run ubiformat /dev/mtd1

You need to interrupt the bootloader after rebooting and run:
run altbootcmd

This will switch your active rootfs partition to one you wrote to and boot from it.

So if rootfs1 is active, then it will change it to rootfs2.

This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0
If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those.
This will result in wrong ordering and OpenWrt will panic on boot.

5. Transfer sysupgrade image
6. Flash with sysupgrade -n.

Note that sysupgrade will write the image to rootfs partition that is not currently in use.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-17 08:42:17 +02:00
Robert Marko
179073b0cc firmware: ipq-wifi: enable use on IPQ806x
This enables the ipq-wifi package to be used on IPQ806x target.
Its needed for boards using a different BDF than one shipped in the upstream board-2.bin.

Currently needed for Edgecore ECW5410.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-17 08:42:17 +02:00
Paul Spooren
35f2116519 treewide: https for downloads.openwrt.org sources
Instead of using http and https for source downloads from
downloads.openwrt.org, always use https for it's better security.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-08-31 11:26:10 +01:00
Adrian Schmutzler
4e4ee46495 ar71xx: drop target
This target has been mostly replaced by ath79 and won't be included
in the upcoming release anymore. Finally put it to rest.

This also removes all references in packages, tools, etc. as well as
the uboot-ar71xx and vsc73x5-ucode packages.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-30 22:18:35 +02:00
Josef Schlehofer
ed381e2fb2 linux-firmware: add support for Marvell SDIO 8997
For example, Turris MOX SDIO card is using Marvell (NXP) 88W8997 chip.

Technical specs of 88W8997:
- 28nm
- 802.11 ac wave-2
It should support simultaneous dual-band 2.4 GHz and 5 GHz,
but it requires to support multiSSID for one Wi-Fi card [1], which is
not supported in OpenWrt, yet and if we tried to run two instances of
hostapd, it didn't work well, so it's 2.4 GHz or 5 GHz.
- 2x2 MU-MIMO
- Bluetooth 5.1 with LE support
- Unfortunately, there can be connected only 8 clients at the same time
(limited by FW, however, there exists "enterprise" chip, its equal chip,
it is just different that it uses different FW)

Symlink is necessary as mwifiex_sdio tries to load sd8997_uapsta.bin
[   13.651182] mwifiex_sdio mmc0:0001:1: Direct firmware load for mrvl/sd8997_uapsta.bin failed with error -2
[   13.661065] mwifiex_sdio mmc0:0001:1: Falling back to user helper
[   13.684880] firmware mrvl!sd8997_uapsta.bin: firmware_loading_store: map pages failed
[   13.695910] mwifiex_sdio mmc0:0001:1: Failed to get firmware mrvl/sd8997_uapsta.bin
[   13.703774] mwifiex_sdio mmc0:0001:1: info: _mwifiex_fw_dpc: unregister device

Pali Rohár sent two patches [2] [3] into kernel to fix default firmware name for SD8997, so
the symlink will not be required in the future versions of kernel, which
was accepted and right now, according to my details it was backported to 5.8, 5.7 and 5.4

[1] https://bugs.openwrt.org/index.php?do=details&task_id=3243
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=00eb0cb36fad5
[3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=2e1fcac52a9ea

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2020-08-24 18:53:59 +02:00
Josef Schlehofer
18aca6b17d linux-firmware: update to version 20200817
git log --pretty=oneline --abbrev-commit 20200619..20200817
7a30af1 (HEAD -> master, tag: 20200817, origin/master, origin/main, origin/HEAD) Merge branch 'i915-firmware-updates-08-2020' of git://anongit.freedesktop.org/drm/drm-firmware into main
923bfa6 brcm: Add brcmfmac43455-sdio.raspberrypi,3-model-a-plus.txt symlink
33e11ab rtl_bt: Update RTL8822C BT UART firmware to 0x0599_8A4F
1b81373 i915: Add DMC firmware 2.02 for RKL
bdf8d7a i915: Add DMC firmware 2.08 for TGL
1bcdc9a i915: Add HuC firwmare v7.5.0 for TGL
c331aa9 amdgpu: update vega20 firmware for 20.30
a434387 amdgpu: update vega12 firmware for 20.30
49e9ea8 amdgpu: update vega10 firmware for 20.30
d89e9b1 amdgpu: update renoir firmware for 20.30
373c08a amdgpu: update raven2 firmware for 20.30
69ca06e amdgpu: update raven firmware for 20.30
12042c2 amdgpu: update picasso firmware for 20.30
2c9d97a amdgpu: update navi14 firmware for 20.30
eaa3e55 amdgpu: update navi10 firmware for 20.30
9bc3789 linux-firmware: update NXP SDSD-8997 firmware image
6c79b68 Mellanox: Add new mlxsw_spectrum firmware xx.2008.1036
2b823fc (tag: 20200721) linux-firmware: Update AMD SEV firmware
e33306f Merge branch 'qca_0714' of https://github.com/bgodavar/qca_bt_fw into main
1d1c80b Update to 20200629111339 version to aligh SDK. Mainly fix DFS false alarm.
69c7f0b rtl_nic: update firmware for RTL8125B
f39b687 Update binary firmware for MT7663 based devices to include firmware offload feature and low power feature.
3882702 QCA: Add correct bin file for WCN3991
3d3a06f linux-firmware: Update firmware file for Intel Bluetooth AX201
b7849f7 linux-firmware: Update firmware file for Intel Bluetooth AX200
07b0375 linux-firmware: Update firmware file for Intel Bluetooth 9560
44bf1b1 linux-firmware: Update firmware file for Intel Bluetooth 9260
7169ab3 linux-firmware: wilc1000: add wilc1000 v15.4 FW
b1497fc Merge https://github.com/rjliao-qca/qca-btfw into main
c4e04b4 QCA: Update Bluetooth firmware for QCA6390
74ac3b5 Merge https://github.com/bgodavar/qca_wcn3991 into main
1a0c0c2 amdgpu: add UVD firmware for SI asics
24cc617 QCA: Update WCN3991 FW files

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2020-08-24 18:53:59 +02:00
Michael Yartys
91aab77bf1 ath10k-ct-firmware: update firmware images
Not a large change from last time, but should fix at least one rare wave-2
crash. The htt-mgt-community builds are trimmed for supporting lots of
stations (typically 150+ stations per radio).

Tested on Netgear R7800.

Signed-off-by: Michael Yartys <michael.yartys@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-12 11:50:48 +02:00
Adrian Schmutzler
0f3c3a5fb2 layerscape: harmonize device strings
OpenWrt lately has harmonized device (definition) names to the
pattern vendor_model to improve overall consistency, also with
other values like the DTS compatible.

This patch applies that scheme to the layerscape target.

Since this (intentionally) creates a bigger overlap between DTS names,
compatible, and device definition name, it also moves DEVICE_DTS and
SUPPORTED_DEVICES definitions to the Device/Default blocks.

Apart from that, it also modifies several packages to use consistent
naming in order to keep the $(1) file references working.

While at it, remove one layer of complexity for the setup in
tfa-layerscape package.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 12:06:52 +02:00
Tomasz Maciej Nowak
4d92a558f2 linux-firmware: package EIP197 mini firmware
Quoting part of original message from eefb5f741015 commit in
linux-firmware repository:

This adds the "minifw" version of the EIP197 firmware, which the inside-
secure driver will use as a fallback if the original full-featured
firmware cannot be found. This allows for using the inside-secure driver
and hardware without access to "official" firmware only available under
NDA.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-07-11 13:33:28 +02:00
Yanase Yuki
4a77a060ab ipq40xx: add support for Buffalo WTR-M2133HP
Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.

Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A

Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
   and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
    # ubidetach -p /dev/mtd15
    # ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
    # fw_setenv bootcmd bootipq
8. Perform reboot.

Recover to stock firmware
-------------------------
1. Execute the following command.
    # fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
2020-07-08 16:07:05 +02:00
Dongming Han
f103321349 ipq40xx: add support for GL.iNet GL-S1300
Specifications:
SOC:        Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core
RAM:        512 MiB
FLASH1:     16 MiB NOR - SPI0
FLASH2:     8 GiB eMMC
ETH:        Qualcomm QCA8075
WLAN1:      Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2
WLAN2:      Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2
INPUT:      Reset, WPS
LED:        Power, Mesh, WLAN
UART1:      On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
UART2:      On board with BLE module
SPI1:       On board socket for Zigbee module

Install via tftp
- NB: need to flash transition image firstly

Firstly install transition image:
(IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script

Secondly install openwrt sysupgrade bin:
(IPQ40xx) # run lf

Revert to factory image:
(IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script

The kernel and rootfs of factory firmware are on eMMC, and openwrt
firmware is on NOR flash. The transition image includes U-boot
and partition table, which decides where to load kernel and rootfs.
After you firstly install openwrt image, you can switch between
factory and openwrt firmware by flashing transition image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
2020-07-08 16:07:05 +02:00
John Audia
556eb9872d linux-firmware: Update linux-firmware to 20200619
git log --pretty=oneline --abbrev-commit 20200122..20200619

e96c121 (tag: 20200619, origin/main) amdgpu: update renoir firmware from 20.20 release
db0402e amdgpu: update picasso firmware from 20.20 release
c4e6e8f amdgpu: update raven2 firmware from 20.20 release
1967282 amdgpu: update raven firmware from 20.20 release
f73f82c amdgpu: add vega20 TA firmware from 20.20 release
9ecaba8 amdgpu: update vega20 firmware from 20.20 release
3866af1 amdgpu: update vega12 firmware from 20.20 release
adba945 amdgpu: update vega10 firmware from 20.20 release
3c5eef0 amdgpu: update navi10 firmware from 20.20 release
152c929 amdgpu: update navi14 firmware from 20.20 release
3890db3 (HEAD -> master, origin/master, origin/HEAD) rtl_nic: add firmware for RTL8125B
887d2a1 linux-firmware: Update firmware file for Intel Bluetooth AX200
3914943 linux-firmware: Update firmware file for Intel Bluetooth AX201
4966923 linux-firmware: Update firmware file for Intel Bluetooth 9560
5ee82c0 linux-firmware: Update firmware file for Intel Bluetooth 9260
d9880b1 Mellanox: Add new mlxsw_spectrum firmware xx.2007.1168
c2e313b rtw88: RTL8822C: update firmware version to v9.9
4d91664 Merge branch 'mrvl-prestera' of https://github.com/PLVision/linux-firmware
a54dfbe Merge branch 'for-upstream' of git://git.chelsio.net/pub/git/linux-firmware
51a773d cxgb4: Update firmware to revision 1.24.17.0
5611000 mrvl: add firmware for Prestera ASIC devices
8ba6fa6 (tag: 20200519) Merge tag 'iwlwifi-fw-2020-05-19' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware
5ee1c7d iwlwifi: update and add new FWs from core50-70 and core52-81 releases
401bd6d rtw88: RTL8821C: add firmware file v24.5
2ae9974 iwlwifi: update FWs to core47-142 release
50c1340 iwlwifi: update 8265 FW
f8d32e4 rtw88: update firmware information and README
412f95a linux-firmware: add firmware for MT7915E
619d339 QCA: Add Bluetooth firmware for QCA9377
1392591 linux-firmware: add rebb firmware for mt7663
b2cad6a linux-firmware: Update firmware file for Intel Bluetooth AX200
c5ac1ad linux-firmware: Update firmware file for Intel Bluetooth AX201
642d115 linux-firmware: Update firmware file for Intel Bluetooth 9560
dc3047c linux-firmware: Update firmware file for Intel Bluetooth 9260
78c0348 (tag: 20200421) Use Link function for brcmfmac43362-sdio.lemaker,bananapro.txt
f2df706 Add symlink for Dell XPS 15 9550 Broadcom Bluetooth patch-ram file
87dcb0e rtl_bt: Update RTL8822C BT FW to 0x0999_3AA1
3aa3ae4 Merge branch 'for-upstream' of git://git.chelsio.net/pub/git/linux-firmware
8aa36f5 cxgb4: Update T6 config file
6314fa0 amdgpu: update vega20 firmware for 20.10
1f308f1 amdgpu: update vega12 firmware for 20.10
1ffd569 amdgpu: update vega10 firmware for 20.10
9a0b0f4 amdgpu: update renoir firmware for 20.10
428a747 amdgpu: update raven2 firmware for 20.10
624ecdf amdgpu: update raven firmware for 20.10
7532f50 amdgpu: update picasso firmware for 20.10
75e352e amdgpu: update navi10 firmware for 20.10
3c175d1 amdgpu: update navi14 firmware for 20.10
8d7ac32 amdgpu: add navi14 TA firmware from 20.10
dd6b4db Merge branch 'for-upstream' of git://git.chelsio.net/pub/git/linux-firmware
3afe520 cxgb4: Update firmware to revision 1.24.14.0
64dba0f Merge branch 'a630-zap' of https://github.com/andersson/linux-firmware
236ec45 linux-firmware: add firmware for MT7663 Wifi/BT combo device
107b9a2 Merge https://github.com/bgodavar/qca_bt_fw
5b240e5 Merge https://github.com/rjliao-qca/qca-btfw
47533bc linux-firmware: Update firmware file for Intel Bluetooth AX200
677930a linux-firmware: Update firmware file for Intel Bluetooth AX201
e6ff1e7 qcom: Add SDM845 Adreno ZAP shader firmware
1a8b0dc qca: Enable transparent WBS for WCN3991
4921f73 QCA: Add Bluetooth firmware for QCA6390
edf390c Merge branch 'v12573.77' of https://github.com/erinlo/linux_fw_scp
3c213aa mediatek: Add mt8183 SCP firmware
8eb0b28 (tag: 20200316) linux-firmware: Update firmware file for Intel Bluetooth AX200
b9f720f linux-firmware: Update firmware file for Intel Bluetooth AX201
426db50 linux-firmware: Update firmware file for Intel Bluetooth 9560
9361709 linux-firmware: Update firmware file for Intel Bluetooth 9260
3b3dd5a amdgpu: update vega20 firmware from 19.50
4871e7a amdgpu: update vega12 firmware from 19.50
4e7f0f8 amdgpu: update vega10 firmware from 19.50
fce60a9 rtl_bt: Add firmware and configuration files for RTL8822C BT UART chip
d553c05 Merge branch 'tgl_huc_7.0.12_dmc_2.06' of git://anongit.freedesktop.org/drm/drm-firmware
fb83402 i915: Add DMC firmware v2.06 for TGL
45d36b5 i915: add HuC firmware v7.0.12 for TGL
0148cfe Merge https://github.com/rjliao-qca/qca-btfw
94cb0a6 check_whence: python3/utf-8 support
7fa32bc Makefile: improve `make check` usefulness
4bb6805 mediatek: Remove in-tree symlinks
6f50efe Merge branch 'v1.1.4' of https://github.com/ruiwang-mtk/linux_fw_vpu
2db3978 qca: Fix blueooth firmware name for QCA6174
a8a18d1 mediatek: move MT8173 VPU FW to subfolder
efcfa03 linux-firmware: Update firmware file for Intel Bluetooth AX201
83cb43e Merge https://github.com/bgodavar/qca_bt_wcn3991
54b017d qca: Add firmware files for BT chip wcn3991.
2277987 nvidia: add TU116/117 signed firmware
f63922d drm/amdgpu: update to latest 19.50 firmware for raven
1168a90 Merge branch 'v1.1.4' of https://github.com/ruiwang-mtk/linux_fw_vpu_v1.1.4
0bd965d mediatek: update MT8173 VPU firmware to v1.1.4
6f89735 rtl_nic: update firmware for RTL8153A
5351afe rtl_bt: Update RTL8822C BT FW to V0x0998_C2B4
83a7c50 linux-firmware: add firmware for MT7622
feb91a4 linux-firmware: add version 2 for MT7615E
b791e15 amdgpu: update to latest navi10 firmware from 19.50
0ff2f37 Revert "radeon: update oland rlc microcode from amdgpu"
c2df39a Merge branch 'amlogic-vdec' of https://github.com/Elyotna/linux-firmware
fb505a6 amlogic: update video decoder firmwares
6d9f399 amdgpu: add renoir firmware for 19.50
2c08b38 amdgpu: update raven2 firmware for 19.50
8846543 Merge commit '779514ec044a75ee6c9c20e52a2bf291f80d7d4e' of https://github.com/Netronome/linux-firmware
74d71b6 Merge branch 'bt-20200122' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/linux-firmware
779514e nfp: update Agilio SmartNIC flower firmware to rev AOTC-2.12.A.13
3055060 qca: update bluetooth firmware for QCA6174

Signed-off-by: John Audia <graysky@archlinux.us>
2020-07-04 21:12:42 +02:00
Yen-Ting-Shen
3f61e5e1b9 ipq40xx: add support for EnGenius EMR3500
SOC:     IPQ4018 / QCA Dakota
CPU:     Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:    256 MiB
NOR:     32 MiB
ETH:     Qualcomm Atheros QCA8072 (2 ports)
USB:     1 x 2.0 (Host controller in the SoC)
WLAN1:   Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:   Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:   RESET Button
LEDS:    White, Blue, Red, Orange

Flash instruction:

From EnGenius firmware to OpenWrt firmware:

In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emr3500-squashfs-factory.bin directly.

From OpenWrt firmware to EnGenius firmware:

1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
   Put the EnGenius firmware in the TFTP server directory on your computer.
2. Power up EMR3500. Press 4 and then press any key to enter u-boot.
3. Download EnGenius firmware
   (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emr3500-nor-fw-s.img
4. Flash the firmware
   (IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script
5. Reboot
   (IPQ40xx) # reset

Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com>
[squashed update patch, updated to 5.4, dropped BOARD_NAME,
migrated to SOC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-06-13 14:38:03 +02:00
Álvaro Fernández Rojas
aabfd4b1db cypress-firmware: add PROVIDES sections
Some firmwares are already provided by linux-firmware.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-28 10:36:27 +02:00
Yangbo Lu
1b370e7f62 layerscape: update ls-dpl to LSDK-20.04
Update ls-dpl to latest LSDK-20.04.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
70a6a98149 layerscape: define only one package for ls-dpl
We do not have to define package for each board, and
consider variant's installing.
It is easier to maintain ls-dpl with only one package
installing all 4 files as intermediate files.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
b7820d57db layerscape: update ls-mc to LSDK-20.04
Update ls-mc to latest LSDK-20.04.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
2e61c4ac1f layerscape: define only one package for ls-mc
We do not have to define package for each board, and
consider variant's installing.
It is easier to maintain ls-mc with only one package
installing all two images as intermediate files.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
99091f6796 layerscape: update ppfe-firmware to LSDK-20.04
Update ppfe-firmware to latest LSDK-20.04.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
e920530847 layerscape: update fman-ucode to LSDK-20.04
Just update PKG_VERSION/PKG_MIRROR_HASH since fman-ucode
of LSDK-20.04 had no changes.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
6c9d8990a4 layerscape: define only one package for fman-ucode
We do not have to define package for each board, and
consider variant's installing.
It is easier to maintain fman-ucode with only one package
installing all two binaries as intermediate files.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
2e2643f74d layerscape: update ls-rcw to latest LSDK-20.04
Update ls-rcw to latest LSDK-20.04.
Update patch 0001 with a new one.
Drop patch 0002 since it had been integrated.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
084c82c5b0 layerscape: define only one package for ls-rcw
We do not have to define package for each board, and
consider variant's building/installing.
It is easier to maintain ls-rcw with only one package
installing all boards RCW binaries as intermediate
files, each of which is just about hundreds of bytes.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Petr Štetiar
493eef5b27 wireless-regdb: bump to latest release 2020-04-29
Update to latest release.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-30 00:52:04 +02:00
Álvaro Fernández Rojas
a882bfce05 ath10k-ct-firmware: add htt-mgt variants
For wave-2, there is now a new variant: htt-mgt-community (vs the old
full-htt-mgt-community).

The non-full one (hence forth 'diet') compiles out a lot of firmware features
that ath10k does not use. This saves a lot of resources and lets one
configure more stations/vdevs/etc using fwcfg.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-04-28 09:33:09 +02:00
Álvaro Fernández Rojas
06f510df6e ath10k-ct-firmware: update firmware images
No release notes this time.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-04-28 09:33:09 +02:00
Álvaro Fernández Rojas
2e5e9b459e ath10k-ct-firmware: rename ct-htt packages
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-04-28 09:33:09 +02:00
Álvaro Fernández Rojas
658e68f85c ath10k-firmware: move CT firmwares to new package
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-04-28 09:33:09 +02:00
Petr Štetiar
76a0ddf130 wireless-regdb: backport three upstream fixes
Another release is overdue for quite some time, so I'm backporting three
fixes from upstream which I plan to backport into 19.07 as well.

Ref: FS#2880
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-28 07:45:00 +02:00
Álvaro Fernández Rojas
97c5fb4709 cypress-firmware: update to v5.4.18-2020_0402
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-04-13 10:14:48 +02:00
Pawel Dembicki
c30220d458 ipq40xx: add support for Cell C RTL30VW
Cell C RTL30VW is a LTE router with tho gigabit ethernets and integrated
QMI mPCIE modem.

This is stripped version of ASKEY RTL0030VW.

Hardware:

Specification:
-CPU: IPQ4019
-RAM: 256MB
-Flash: NAND 128MB + NOR 16MB
-WiFi: Integrated bgn/ac
-LTE: mPCIe card (Modem chipset MDM9230)
-LAN: 2 Gigabit Ports
-USB: 2x USB2.0
-Serial console: RJ-45 115200 8n1
-Unsupported VoIP

Known issues:

None so far.

Instruction install:

There are two methods: Factory web-gui and serial + tftp.

Web-gui:
1. Apply factory image via stock web-gui.

Serial + initramfs:
1. Rename OpenWrt initramfs image to "image"
2. Connect serial console (115200,8n1)
3. Set IP to different than 192.168.1.11, but 24 bit mask, eg. 192.168.1.4.

4. U-Boot commands:
sf probe && sf read 0x80000000 0x180000 0x10000
setenv serverip 192.168.1.4
set fdt_high 0x85000000
tftpboot 0x84000000 image
bootm 0x84000000

5. Install sysupgrade image via "sysupgrade -n"

Back to stock:

All is needed is swap 0x4c byte in mtd8 from 0 to 1 or 1 to 0,
do firstboot and factory reset with OFW:

1. read mtd8:
dd if=/dev/mtd8 of=/tmp/mtd8
2. go to tmp:
cd /tmp/
3. write first part of partition:
dd if=mtd8 of=mtd8.new bs=1 count=76
4. check which layout uses bootloader:
cat /proc/mtd
5a. If first are kernel_1 and rootfs_1 write 0:
echo -n -e '\x00' >> mtd8.new
5b. If first are kernel and rootfs write 1:
echo -n -e '\x01' >> mtd8.new
6. fill with rest of data:
dd if=mtd8 bs=1 skip=77 >> mtd8.new
7. CHECK IF mtd8.new HAVE CHANGED ONLY ONE BYTE! e.g with:
hexdump mtd8.new
8. write new mtd8 to flash:
mtd write mtd8.new /dev/mtd8
9. do firstboot
10.reboot
11. Do back to factory defaults in OFW GUI.

Based on work: Cezary Jackiewicz <cezary@eko.one.pl>

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-10 15:22:26 +02:00
DENG Qingfang
a30abb1b6b ipq40xx: add support for MobiPromo CM520-79F
MobiPromo CM520-79F is an AC1300 dual band router based on IPQ4019

Specification:

SoC/Wireless: QCA IPQ4019
RAM: 512MiB
Flash: 128MiB SLC NAND
Ethernet PHY: QCA8075
Ethernet ports: 1x WAN, 2x LAN
LEDs: 7 LEDs
      2 (USB, CAN) are GPIO
      other 5 (2.4G, 5G, LAN1, LAN2, WAN) are connected to a shift register
Button: Reset

Flash instruction:
Disassemble the router, connect UART pins like this:
 GND TX    RX
  [x x . . x .]
  [. . . . . .]

(QCA8075 and IPQ4019 below)
Baud-rate: 115200

Set up TFTP server: IP 192.168.1.188/24
Power on the router and interrupt the booting with UART console
env backup (in case you want to go back to stock and need it there):
	printenv
	(Copy the output to somewhere save)
Set bootenv:
	setenv set_ubi 'set mtdids nand0=nand0; set mtdparts mtdparts=nand0:0x7480000@0xb80000(fs); ubi part fs'
	setenv bootkernel 'ubi read 0x84000000 kernel; bootm 0x84000000#config@1'
	setenv cm520_boot 'run set_ubi; run bootkernel'
	setenv bootcmd 'run cm520_boot'
	setenv bootargs
	saveenv
Boot initramfs from TFTP:
	tftpboot openwrt-ipq40xx-generic-mobipromo_cm520-79f-initramfs-fit-zImage.itb
	bootm
After initramfs image is booted, backup rootfs partition in case of reverting to stock image
	cat /dev/mtd12 > /tmp/mtd12.bin
Then fetch it via SCP

Upload nand-factory.ubi to /tmp via SCP, then run
	mtd erase rootfs
	mtd write /tmp/*nand-factory.ubi rootfs
	reboot

To revert to stock image, restore default bootenv in uboot UART console
	setenv bootcmd 'bootipq'
	printenv
use the saved dump you did back when you installed OpenWrt to verify that
there are no other differences from back in the day.
	saveenv
upload the backed up mtd12.bin and run
	tftpboot mtd12.bin
	nand erase 0xb80000 0x7480000
	nand write 0x84000000 0xb80000 0x7480000
The BOOTCONFIG may have been configured to boot from alternate partition (rootfs_1) instead
In case of this, set it back to rootfs:
	cd /tmp
	cat /dev/mtd7 > mtd7.bin
	echo -ne '\x0b' | dd of=mtd7.bin conv=notrunc bs=1 count=1 seek=4
	for i in 28 48 68 108; do
		dd if=/dev/zero of=mtd7.bin conv=notrunc bs=1 count=1 seek=$i
	done
	mtd write mtd7.bin BOOTCONFIG
	mtd write mtd7.bin BOOTCONFIG1

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[renamed volume to ubi to support autoboot,
as per David Lam's test in PR#2432]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-04-10 15:22:26 +02:00
Petr Štetiar
5fbcb52648 linux-firmware: add firmware for RTL8723BS SDIO modules
Adds firmware package for Realtek RTL8723BS SDIO Wireless LAN NIC driver
available in the staging.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Álvaro Fernández Rojas
84f4a783c6 ath10k-firmware: update ath10k-ct firmware images
Release notes for 017:

Wave-1:

 *  March 19, 2020:  Fix problem where power-save was not enabled when going off-channel to scan.
                     The problem was a boolean logic inversion in the chmgr code, a regression I introduced
                     a long time ago.

 *  March 19, 2020:  When scanning only on current working channel, do not bother with disable/enable
                     powersave.  This should make an on-channel scan less obtrusive than it was previously.

 *  March 23, 2020:  Fix channel-mgr use-after-free problem that caused crashes in some cases.  The crash
                     was exacerbated by recent power-save changes.

 *  March 23, 2020:  Fix station-mode power-save related crash:  backported the fix from 10.2 QCA firmware.

 *  March 23, 2020:  Attempt to better clean up power-save objects and state, especially in station mode.

Release notes for 016:

Wave-1 changes, some debugging code for a crash someone reported, plus:

*  February 28, 2020:  Fix custom-tx path when sending in 0x0 for rate-code.  Have tries == 0 mean
                        one try but NO-ACK (similar to how wave-2 does it).

wave-2:

 * Fixed some long-ago regressions related to powersave and/or multicast.  Maybe fix some
   additional multicast and/or tx-scheduling bugs.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
2020-03-27 10:18:41 +01:00
Tomasz Maciej Nowak
3a3d998c12 layerscape: resurrect support for FRDM-LS1012A
Re-add support for NXP FRDM-LS1012A, which mimics the flash layout of the
rest boards supported by LSDK.

0x000000000000-0x000000100000 : "bl2"
0x000000100000-0x000000500000 : "fip"
0x000000500000-0x000000600000 : "u-boot-env"
0x000000600000-0x000000a00000 : "reserved-1"
0x000000a00000-0x000000d00000 : "pfe"
0x000000d00000-0x000000f00000 : "reserved-2"
0x000000f00000-0x000001000000 : "dtb"
0x000001000000-0x000002000000 : "kernel"
0x000002000000-0x000004000000 : "ubifs"

Specification
SoC: LS1012A single core 800MHz
RAM: 512 MB DDR3
Flash: 64 MB QSPI NOR
Ethernet: 2x 10/100/1000 Mbps
Connectors: µUSB 3.0 OTG
            µUSB 2.0 (debugging & power input)
            2x 3.5mm jack for microphone & headphone (SGTL5000)
            Arduino Shield expansion with I2C, SPI, UART, and GPIO
            JTAG
LEDS: 3x (non-configurable)
Buttons: 1x (reset, non-configurable)

Be advised that erasing or writing 64MB flash takes some time to finish.
Do not reset the board until all operations end with success, otherwise
You'll need external tools to re-program the flash chip.

Installation
Follow the QSPI programing procedure for LS1012AFRWY board in
target/linux/layerscape/README, point 3.3.
Don't forget about updating U-Boot environment with MAC addresses of
ethernet interfaces, variable 'ethaddr' for eth0 and 'eth1addr' for eth1.

As the LSDK images do not support sysupgrade, nor do changes in this
commit, it's planed in upcoming submissions.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-03-12 12:59:44 +01:00
Robert Marko
6256ca3232 ipq40xx: add support for 8devices Habanero DVK
This patch adds support for the 8devices Habanero development board.

Specs are:
CPU: QCA IPQ4019
RAM: DDR3L 512MB
Storage: 32MB SPI-NOR and optional Parallel SLC NAND(Some boards ship with it and some without)
WLAN1: 2.4 GHz built into IPQ4019 (802.11n) 2x2
WLAN2: 5 GHz built into IPO4019 (802.11ac Wawe-2) 2x2
Ethernet: 5x Gbit LAN (QCA 8075)
USB: 1x USB 2.0 and 1x USB 3.0 (Both built into IPQ4019)
MicroSD slot (Uses SD controller built into IPQ4019)
SDIO3.0/EMMC slot (Uses the same SD controller)
Mini PCI-E Gen 2.0 slot (Built into IPQ4019)
5x LEDs (4 GPIO controllable)
2x Pushbutton (1 is connected to GPIO, other to SoC reset)
LCD ZIF socket (Uses the LCD controller built into IPQ4019 which has no driver support)
1x UART 115200 rate on J18

2x breakout development headers
12V DC Jack for power
DIP switch for bootstrap configuration

Installation instructions:
Since boards ship with vendors fork of OpenWrt sysupgrade can be used.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2020-03-09 00:53:50 +01:00
Steven Lin
a736d912e2 ipq40xx: add support for EnGenius EAP2200
SOC:    IPQ4019 / QCA Dakota
CPU:    Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:   256 MiB
FLASH:  NOR 4 MiB + NAND 128 MiB
ETH:    Qualcomm Atheros QCA8072
WLAN1:  Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2:2x2
WLAN2:  Qualcomm Atheros QCA4019 5GHz 802.11a/n/ac 2:2x2
WLAN2:  Qualcomm Atheros QCA9888 5GHz 802.11a/n/ac 2:2x2
INPUT:  WPS Button
LEDS:   Power, LAN1, LAN2, WLAN 2.4GHz, WLAN 5GHz-1, WLAN 5GHz-2, OPMODE

1. Load Ramdisk via U-Boot

To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
   * 115200bps
   * 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports.
c. Set a static ip 192.168.99.8 for Ethernet that connects to board.
d. The PC must have a TFTP server launched and listening on the interface to which the board is connected.
e. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.

U-BOOT> set serverip 192.168.99.9 && tftpboot 0x84000000 192.168.99.8:openwrt.itb && bootm

Signed-off-by: Steven Lin <steven.lin@senao.com>
[copied 4.19 dts to 5.4]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-02-28 22:29:10 +01:00
DENG Qingfang
e6cec17568 linux-firmware: update to 20200122
Update linux-firmware to 20200122

git log --pretty=oneline --abbrev-commit 20191215..20200122

1eb2408 linux-firmware: Update firmware file for Intel Bluetooth AX200
0dc1611 linux-firmware: Update firmware file for Intel Bluetooth AX201
d03f79c linux-firmware: Update firmware file for Intel Bluetooth 9560
aab62bc linux-firmware: Update firmware file for Intel Bluetooth 9260
ed0aa3a nvidia: add TU102/TU104/TU106 signed firmware
9c340bd amdgpu: update navi10 firmware for 19.50
3b4a503 amdgpu: Add navi10 TA ucode
16cc13a Merge branch 'v1.1.3' of https://github.com/ruiwang-mtk/linux_fw_vpu_v1.1.37f3177d mediatek: update MT8173 VPU firmware to v1.1.3
67d4ff5 Mellanox: Add new mlxsw_spectrum firmware xx.2000.2714
f1c9e7b radeon: update oland rlc microcode from amdgpu
b1dafb7 amdgpu: update vega20 microcode for 19.50
c38789e amdgpu: update vega12 microcode for 19.50
5a141c1 amdgpu: update vega10 microcode for 19.50
a03173a amdgpu: update picasso microcode for 19.50
86e9a5f amdgpu: update raven2 microcode for 19.50
febe09a amdgpu: update raven microcode for 19.50
af76fd0 amdgpu: update navi10 microcode for 19.50
b5b176a amdgpu: update navi14 microcode for 19.50
ad90178 amdgpu: add TA microcode for Raven asics
379551b qed: Add firmware 8.42.2.0
58b4003 Merge branch 'RB3-wlan-firmware-1387-v2' of https://github.com/andersson/linux-firmware
5967a45 Adjust WHENCE entry to check_whence doesn't complain
d1e743d Merge branch 'master' of https://github.com/NXP/mwifiex-firmware
d6219ab qcom: Switch SDM845 WLAN firmware
e65245c linux-firmware: add NXP firmware licence file
6871bff Merge branch 'ath10k-20191220' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/linux-firmware
b142c2e ath10k: WCN3990 hw1.0: add firmware WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
8809b87 ath10k: QCA9984 hw1.0: update firmware-5.bin to 10.4-3.9.0.2-00070
513d70c ath10k: QCA988X hw2.0: update firmware-5.bin to 10.2.4-1.0-00047
203435b ath10k: QCA9888 hw2.0: update firmware-5.bin to 10.4-3.9.0.2-00070
a66d2fc ath10k: QCA9887 hw1.0: update firmware-5.bin to 10.2.4-1.0-00047
6d19154 ath10k: QCA6174 hw3.0: update board-2.bin
c4586ff linux-firmware: Update AMD cpu microcode

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-02-22 16:38:41 +01:00
Adrian Schmutzler
7d7aa2fd92 brcm2708: rename target to bcm27xx
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.

Despite, since subtargets range from bcm2708 to bcm2711, it seems
appropriate to use bcm27xx instead of bcm2708 (again, as already done
for BOARDNAME).

This also renames the packages brcm2708-userland and brcm2708-gpu-fw.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-02-14 14:10:51 +01:00
Michael Yartys
1862263883 ath10k-firmware: update ath10k-ct firmware
This supports better per-chain noise floor reporting, which in turn allows for
better RSSI reporting in the driver.

Wave-2 fixes a long-standing rate-ctrl problem when connected to xbox (and probably other devices).

Wave-2 has fix for crash likely related to rekeying.

Wave-1 has some debugging code added where a user reported a crash.

Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>  [ipq806x+qca9984,ipq4019+qca9986]
Signed-off-by: Michael Yartys <michael.yartys@protonmail.com>
2020-02-13 17:45:46 +01:00
Álvaro Fernández Rojas
ffbb8ed5a2 cypress-firmware: update to v4.14.77-2020_0115
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-02-01 10:59:51 +01:00
Christian Lamparter
a59f1ec30f ipq-wifi: drop deprecated .bin support
This patch converts the Qxwlan E2600AC image away from
the deprecated .bin file and to the new .qca4019 method.

As a result, we no longer need to carry around the
legacy support for handling .bin files.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-01-26 01:20:46 +01:00
Yen-Ting-Shen
51f3035978 ipq40xx: add support for EnGenius EMD1
SOC:     IPQ4018 / QCA Dakota
CPU:     Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:    256 MiB
NOR:     32 MiB
ETH:     Qualcomm Atheros QCA8072 (1 port)
WLAN1:   Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:   Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:   RESET Button
LEDS:    White, Blue, Red, Orange

Flash instruction:

From EnGenius firmware to OpenWrt firmware:

In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emd1-squashfs-factory.bin directly.

From OpenWrt firmware to EnGenius firmware:

1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
   Put the EnGenius firmware in the TFTP server directory on your computer.
2. Power up EMD1. Press 4 and then press any key to enter u-boot.
3. Download EnGenius firmware
   (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emd1-nor-fw-s.img
4. Flash the firmware
   (IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script
5. Reboot
   (IPQ40xx) # reset

Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com>
[removed BOARD_NAME]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-01-26 01:20:45 +01:00
Fredrik Olofsson
52b8c7a892 ipq40xx: Add support for D-Link DAP-2610
Specifications
==============
- SOC: IPQ4018
- RAM: DDR3 256MB
- Flash: SPI NOR 16MB
- WiFi:
    - 2.4GHz: IPQ4018, 2x2, front end SKY85303-11
    - 5GHz: IPQ4018, 2x2, front end SKY85717-21
- Ethernet: 1x 10/100/1000Mbps, POE 802.3af
- PHY: QCA8072
- UART: GND, blocked, 3.3V, RX, TX / 115200 8N1
- LED: 1x red / green
- Button: 1x reset / factory default
- U-Boot bootloader with tftp and "emergency web server" accessible
  using serial port.

Installation
============
Flash factory image from D-Link web UI. Constraints in the D-Link web UI
makes the factory image unnecessarily large. Flash again using
sysupgrade from inside OpenWrt to reclaim some flash space.

Return to stock D-Link firmware
===============================
Partition layout is preserved, and it is possible to return to the stock
firmware simply by downloading it from D-Link and writing it to the
firmware partition.

    # mtd -r write dap2610-firmware.bin firmware

Quirks
======
To be flashable from the D-Link http server, the firmware must be larger
then 6MB, and the size in the firmware header must match the actual file
size. Also, the boot loader verifies the checksum of the firmware before
each boot, thus the jffs2 must be after the checksum covered part. This
is solved in the factory image by having the rootfs at the very end of
the image (without pad-rootfs).

The sysupgrade image which does not have to be flashable from the D-Link
web UI may be smaller, and the checksum in the firmware header only
covers the kernel part of the image.

Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
[added WRGG Variables to DEVICE_VARS, squashed spi pinconf/mux,
added emd1's gmac0 config,fix dtc warnings]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-01-26 01:20:45 +01:00
DENG Qingfang
2d758129ca ath10k-firmware: fix mirror hash
Fix PKG_MIRROR_HASH hash mismatch.

Fixes: 641a93f0f2 ("ath10k-firmware: update wave 1 firmware to 10.2.4-1.0-00047")
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[added missing commit description]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-01-24 08:21:04 +01:00