When PHY's are defined on the MDIO bus in the DTS, gigabit support was
being masked out for no apparent reason, pegging all such ports to 10/100.
If gigabit support must be disabled for some reason, there should be a
"max-speed" property in the DTS.
Reported-by: James McKenzie <openwrt@madingley.org>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
(cherry picked from commit 379fe50672)
* Refreshed patches.
* Removed patches:
- target/linux/ar71xx/patches-4.9/103-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch superseded by upstream
- target/linux/ar71xx/patches-4.9/403-mtd_fix_cfi_cmdset_0002_status_check.patch superseded by upstream
- target/linux/brcm63xx/patches-4.9/001-4.11-01-mtd-m25p80-consider-max-message-size-in-m25p80_read.patch accepted upstream
- target/linux/brcm63xx/patches-4.9/001-4.15-08-bcm63xx_enet-correct-clock-usage.patch accepted upstream
- target/linux/brcm63xx/patches-4.9/001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch accepted upstream
- target/linux/generic/pending-4.9/900-gen_stats-fix-netlink-stats-padding.patch
* New backported patch to address ext4 breakage, introduced in 4.9.112:
- backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch
Also add ARM64_SSBD symbol to ARM64 targets still running kernel 4.9
Thanks to Koen Vandeputte for pointing out the need to add the ARM64_SSBD symbol, and the ext4 patch.
Compile-tested on: ar71xx
Run-tested on: ar71xx
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
The Linux headers on arm64 architectures contain references to common
arch/arm/ headers which were not bundled by the SDK so far.
Check if we're packing the SDK for an arm64 target and if we do, also
include arch/arm headers as well.
Fixes FS#1725.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 4bb8a678e0)
2.0.12 change set (as of June 25th 2018)
o Change the unicast TTL default value from 1 to the system default (to be compatable with previous versions.) Mulitcast still defaults to 1.
o adpative formatting bug fix: crash occurs when values exceed 1 Tera. Add support for Tera and Peta and eliminate the potential crash condition
o configure default compile to include isochronous support (use configure --disable-isochronous to remove support)
o replace 2.0.11's --vary-load option with a more general -b option to include <mean>,<stdev>, e.g. -b 100m,40m, which will pull from a log normal distribution every 0.1 seconds
o fixes for windows cross compile (using mingw32)
o compile flags of -fPIE for android
o configure --enable-checkprograms to compile ancillary binaries used to test things such as delay, isoch, pdf generation
o compile tests when trying to use 64b seq numbers on a 32b platform
o Fix GCC ver 8 warnings
2.0.11 change set (as of May 24th, 2018)
o support for -b on server (read rate limiting)
o honor -T (ttl) for unicast. (Note: the default value is 1 so this will impact unicast tests that require routing)
o support for --isochronous traffic with optional frames per second, mean and variance uses a log normal distribution (requires configure w/-enable-isochronous and compile)
o support for --udp triggers (requires configure w/ --enable-udptriggers, early code with very limited support)
o support for --udp-histogram with optional bin width and number of bins (default is 1 millisecond bin width and 1000 bins)
o support for frame (burst) latency histograms when --isochronous is set
o support for --tx-sync with -P for synchonrized writes. Initial use is for WiFi OFDMA latency testing.
o support for --incr-dstip with -P for simultaneous flows to multiple destinations (use case is for OFDMA)
o support for --vary-load with optional weight, uses log normal distribution (requires -b to set the mean)
o support for --l2checks to detect L2 length errors not detected by v4 or v6 payload length errors (requires linux, berkeley packet filters BPFs and AF_PACKET socket support)
o support for server joining mulitcast source specific multicast (S,G) and (*,G) for both v4 and v6 on platforms that support it
o improved write counters (requires -e)
o accounting bug fix on client when write fails, this bug was introduced in 2.0.10
o slight restructure client/server traffic thread code for maintainability
o python: flow example script updates
o python: ssh node object using asyncio
o python: histograms in flows with plotting (assumed gnuplot available)
o python: hierarchical clustering of latency histograms (early code)
o man pages updates
o Note: latency histograms require client and server system clock synchronization. A GPS disciplined oscillator using Precision Time Protocol works well for this.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Bundle the usbip utility sources shipped with the Linux kernel tree in
order to allow the usbip packages from the package feed to build within
the OpenWrt SDK.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit d0e0b7049f)
This includes Linksys EA9500 support, BCM53573 timer fix and
upstream-ready partitions patch that replaces two downstream hacks.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit a07730472c)
USB 3.0 PHY is attached to the MDIO bus and should be supported
(accessed) as a MDIO device. This wasn't known initially which resulted
in writing driver that was working with MDIO bus (using some magic
values) without knowing it.
This commit updates DT to properly describe MDIO & USB 3.0 PHY and
enables required kernel drivers.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 8a175ea219)
This is a new & warm feature that allows nesting partiitons in DT and
mixing their types (e.g. static vs. dynamic). It's very useful for
boards that have most partitions static but some of them require extra
parsing (e.g. a "firmware" partition).
It's required to successfully backport support for new devices using
that new syntax in their DT files.
Since brcm63xx has a custom alternative patch the upstream one is being
reverted for it. The plan is to make brcm63xx use the upstream
implementation.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 2a598bbaa3)
Two tiny & trivial patches with no regression risk. One simplifies
bcm53xx downstream patch.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 6bcafea2c0)
The 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch kernel patches
break the possibility for using an ip4ip6 tunnel interface as a fall
back interface accepting ip4-in-ip6 tunneled packets from any remote
address. This works out of the box with any normal (non-666-patched)
kernel and can be configured by setting up an 'ip -6 tunnel' with type
'any' or 'ip4ip6' and a remote address of '::'.
The misbehavior comes with line 290 the patch which discards all packets
that do not show the expected saddr, even if no single fmr rule was
defined and despite the validity of the saddr was already approved earlier.
Signed-off-by: Axel Neumann <neumann@cgws.de>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
(cherry picked from 65c05301c2)
AT803X_REG_CHIP_CONFIG and AT803X_BT_BX_REG_SEL have been defined
upstream by commit f62265b53ef3 ("at803x: double check SGMII side autoneg")
An existing local patch then added those exact same defines again which
isn't necessary, so remove them.
Fixes: f791fb4af4 ("kernel: add linux 4.9 support")
Fixes: b3f95490b9 ("kernel: generic: Add kernel 4.14 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 67fcff6aaf)
The patch was wrongly removed by a kernel version bump to 4.9.106 in
the believe that it was merged upstream thow it wasn't. This lead to
unrecoverable link losses on devices which use those PHYs such as
many ubnt single-port CPEs.
Fixes: 6f8eb1b50f ("kernel: bump 4.9 to 4.9.106 for 18.06")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit a497e47762)
This reverts commit 3442ec5d57.
The device behaviour is reportedly erratic so let's not take chances and
leave this out for now.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Tested with 18.06.0-rc2/ar71xx/generic/tl-wdr4300-v1, image & list
This PR is based on the work of @fewckert[1] with slight improvements.
Add function `manifest` to show the manifest of the produced image,
before actually building it. The manifest contains an orderd list of
package name and version.
This is usefull to check package dependencies but also determine a
unique and reproducible image name before building the package. The
sysupgrade server[2] builds images on request with individual package
selection. To distignish between created images which contain differnt
packages, the EXTRA_IMAGE_NAME is set to a shortend hash of the
manifest's content. So far the image was renamed afterwards as the
manifests content was unknown, however this corrupts the signed
sha256sums. This patch allows a clean solution as to dtermine the
manifest in advance and set the EXTRA_IMAGE_NAME accordingly.
[1]: https://github.com/lede-project/source/pull/1591
[2]: https://github.com/aparcar/attendedsysupgrade-server
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry-picked from commit 869b0d11db)
Qxwlan E750G v8 is based on Qualcomm QCA9344.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4G GHz (AR9344)
- 2x 10/100 Mbps Ethernet (PoE support)
- 2x 10/100/1000 Mbps Ethernet
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
(cherry picked from commit 53a4502013)
Qxwlan E750A v4 is based on Qualcomm QCA9344.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 5G GHz (AR9344)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
(cherry picked from commit ac03d51a3f)
Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9558)
- 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 4x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 3-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (JP5) and LEDs (J8) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
(cherry picked from commit b74f63f81d)
@vahid-dan reported a issue with extracting the rpi images with
Gnome's Archive Manager:
"Ubuntu Archive Manager cannot extract the file and it just
throws a general error message: "An error occurred while
extracting files".
<https://forum.lede-project.org/t/corrupted-pre-built-v18-06-0-rc2-image-for-rpi>
@blogic told me to split the single sdcard.img.gz for the RPi
into a sysupgrade and a factory image for all brcm2708 targets.
The factory images will have no metadata attached, this way
these utilities that can't deal with the attached metadata will
not fail for no reason.
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 7516a96011)
When attempting to use any of the functions in network.sh while netifd is
not started yet, the ubus interface dump query will fail with "Not found",
yielding an empty response.
Subsequently, jsonfilter is invoked with an empty string instead of a valid
JSON document, causing it to emit a second "unexpected end of data" error.
This caused the dnsmasq init script to log the following errors during
early boot on some systems:
procd: /etc/rc.d/S19dnsmasq: Command failed: Not found.
procd: /etc/rc.d/S19dnsmasq: Failed to parse json data: unexpected end of data.
Fix the issue by allowing the ubus query to fail with "Not found" but still
logging other failures, and by passing an empty JSON object to jsonfilter
if the interface status cache is empty.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Update to new iwinfo version.
Adds support for channel survey.
Adds ubus support.
Etc.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 296ae7ab89)
e59f925 hardware: add device ids for QCA9984, 88W8887 and 88W8964 radios
2a82f87 nl80211: back out early when receiving FAIL-BUSY reply
77c32f0 nl80211: fix code calculating average signal and rate
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit 20b76c0a5b)
e15c63a375 introduced code that was trying
to register GPIO 1 as both an LED and a button. The OEM source makes it
clear that LED1 is not wired to the SoC GPIOs. GPIO 1 is the reset button.
Furthermore the (green) power led default state should also be defined,
(matching OEM source), and it should be used by diag.sh since it's
currently the only software-controllable LED.
This patch fixes these issues and renames the corresponding #defines for
clarity
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit e99f760235)
On brcm47xx boards, the model ID is the combination of the "boardtype" nvram
variable and an optional supplemental "boardnum" variable while the human
readable model name is usually exposed in the "machine" field of the
/proc/cpuinfo file.
Move the extraction of the board nvram variables and model name string into
the 01_sysinfo file and rework the 01_detect board configuration script to
solely use the prepared sysinfo values without performing own detection
logic.
As a consequence, we can drop the ucidef_set_board_id() and
ucidef_set_model_name() invocations in favor to the generic behaviour
which copies the /tmp/sysinfo/{board_name,model} values into the board.json
"id" and "name" fields respectively.
Since "01_detect" only contains network configuration logic after this
change, move it to "01_network" and rename the contained "detect_by_xxx"
functions to "configure_by_xxx" instead, to avoid potential confusion.
Fixes FS#1576
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit d7d10f2c1e)
That upstream commit caused instability in flash reads. It was reported
but there isn't any proper fix as for now.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 0417b08b06)
Refresh patches
Upstream commits since last bump:
3b6eb19 Log DNSSEC trust anchors at startup.
f3e5787 Trivial comment change.
c851c69 Log failure to confirm an address in DHCPv6.
a3bd7e7 Fix missing fatal errors when parsing some command-line/config options.
ab5ceaf Document the --help option in the french manual
1f2f69d Fix recurrent minor spelling mistake in french manual
f361b39 Fix some mistakes in french translation of the manual
eb1fe15 When replacing cache entries, preserve CNAMES which target them.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 1e93ef8498)
As dnsmasq is started earlier than netifd usage of network.sh functions
at boottime will fail; therefore don't call at boottime the functions
which construct the dhcp pool/relay info.
As interface triggers are installed the dhcp pool/relay info will be
constructed when the interface gets reported as up by netifd.
At the same time also register interface triggers based on DHCP relay
config.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
(cherry picked from commit 2336b942b3)
Refresh patches and backport upstream to current HEAD:
a997ca0 Fix sometimes missing DNSSEC RRs when DNSSEC validation not enabled.
51e4eee Fix address-dependent domains for IPv6.
05ff659 Fix stupid infinite loop introduced by preceding commit.
db0f488 Handle some corner cases in RA contructed interfaces with addresses changing interface.
7dcca6c Warn about the impact of cache-size on performance.
090856c Allow zone transfer in authoritative mode whenever auth-peer is specified.
cc5cc8f Sane error message when pcap file header is wrong.
c488b68 Handle standard and contructed dhcp-ranges on the same interface.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit fbf475403b)
This fixes kernel hang when booting on BCM4718A1 (& probably BCM4717A1).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 4c1aa64b4d)
The most important is probably regression fix in handling platform
NVRAM. That bug stopped hardware from being properly calibrated breaking
e.g. 5 GHz for Netgear R8000.
Other than that it triggers memory dumps when experiencing firmware
problems which is important for debugging purposes.
Fixes: 2811c97803 ("mac80211: backport brcmfmac firmware & clm_blob loading rework")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit b26214adb5)
40e0931 libubus: pass an empty UBUS_ATTR_DATA block if msg is NULL on invoke
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 7316515891)
Reduces .ipk size on MIPS from 41.6k to 41.1k
Changes:
30463d0 zones: add interface/subnet bound LOG rules
0e77bf2 options: treat time strings as UTC times
d2bbeb7 firewall3: make reject types selectable by user
aa8846b ubus: avoid dumping interface state with NULL message
Cherry picked and squashed from commits:
a3f2451fba firewall: update to latest git HEAD
433d71e73e fw3: update to latest git HEAD
ef96d1e34a firewall: compile with LTO enabled
1e83f775a3 firewall3: update to latest git HEAD
3ee2c76ae0 firewall: update to latest git HEAD
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
884be45 libubus: check for non-NULL data before running callbacks
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit a5c3bbaf56)
This watchdog script tries to re-resolve hostnames for inactive WireGuard peers.
Use it for peers with a frequently changing dynamic IP.
persistent_keepalive must be set, recommended value is 25 seconds.
Run this script from cron every minute:
echo '* * * * * /usr/bin/wireguard_watchdog' >> /etc/crontabs/root
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
[bump the package release]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 20c4819c7b)
80b41cd version: bump snapshot
fe5f0f6 recieve: disable NAPI busy polling
e863f40 device: destroy workqueue before freeing queue
81a2e7e wg-quick: allow link local default gateway
95951af receive: use gro call instead of plain call
d9501f1 receive: account for zero or negative budget
e80799b tools: only error on wg show if all interfaces failk
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
[Added commit log to commit description]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 57b808ec88)
* device: print daddr not saddr in missing peer error
* receive: style
Debug messages now make sense again.
* wg-quick: android: support excluding applications
Android now supports excluding certain apps (uids) from the tunnel.
* selftest: ratelimiter: improve chance of success via retry
* qemu: bump default kernel version
* qemu: decide debug kernel based on KERNEL_VERSION
Some improvements to our testing infrastructure.
* receive: use NAPI on the receive path
This is a big change that should both improve preemption latency (by not
disabling it unconditionally) and vastly improve rx performance on most
systems by using NAPI. The main purpose of this snapshot is to test out this
technique.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
(cherry picked from commit 4630159294)
This partly reverts ca32373c95 which lets
profiles that suppress packages to alter the package selection for all
devices of the target when building with CONFIG_TARGET_PER_DEVICE_ROOTFS.
In particular, this caused the brcm47xx Edimax PS-1208MFG profile to
disable mtd, dropbear, firewall and other essential packages for all
brcm47xx/generic builds.
To solve this problem, prevent profiles from mangling the global
DEFAULT_PACKAGES selection and restrict the supression of negated
packages to the local PACKAGE variable list only.
Fixes ca32373c95 ("target.mk: let profile remove from DEFAULT_PACKAGES")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 69ea512c62)
The WDR4900v1 uses the P1040 SoC, so the device tree pulls in the
definition for the related P1010 SoC. However, the P1040 lacks the
CAAM/SEC4 hardware crypto accelerator which the P1010 device tree
defines. If left defined, this causes the CAAM drivers (if present) to
attempt to use the non-existent device, making various crypto-related
operations (e.g. macsec and ipsec) fail.
This commit overrides the incorrect dt node definition in the included
file.
See also:
- https://bugs.openwrt.org/index.php?do=details&task_id=1262
- https://community.nxp.com/thread/338432#comment-474107
Signed-off-by: Tim Small <tim@seoss.co.uk>
(cherry picked from commit e97aaf483c)
iproute2's tc was updated to support the recently upstreamed cake qdisc.
Backport this canonical support from upstream into iproute2 v4.16
There is no kernel kmod/userspace tc ABI change in this release from the
previous package bump, so everyone can breath a sigh of relief.
This is largely a code style change, the exception to prove the rule:
option 'autorate_ingress' has been changed to 'autorate-ingress' to fit
in with upstream option naming expectations.
No openwrt package (e.g. sqm-scripts) has knowledge of
'autorate_ingress' thus only users who made their own scripts or used
it within the 'dangerous configuration' options of sqm-scripts will be
affected.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
