Hardware
--------
SoC: Qualcomm IPQ8065
RAM: 512 MB DDR3
Flash: 256 MB NAND (Macronix MX30UF2G18AC) (split into 2x128MB)
4 MB SPI-NOR (Macronix MX25U3235F)
WLAN: Qualcomm Atheros QCA9984 - 2.4Ghz
Qualcomm Atheros QCA9984 - 5Ghz
ETH: eth0 - POE (100Mbps in U-Boot, 1000Mbps in OpenWrt)
eth1 - (1000Mbps in both)
Auto-negotiation broken on both.
USB: USB 2.0
LED: 5G, 2.4G, ETH1, ETH2, CTRL, PWR (All support green and red)
BTN: Reset
Other: SD card slot (non-functional)
Serial: 115200bps, near the Ethernet transformers, labeled 9X.
Connections from the arrow to the 9X text:
[NC] - [TXD] - [GND] - [RXD] - [NC]
Installation
------------
0. Connect to the device
Plug your computer into LAN2 (1000Mbps connection required).
If you use the LAN1/POE port, set your computer to force a 100Mbps link.
Connect to the device via TTL (Serial) 115200n8.
Locate the header (or solder pads) labeled 9X,
near the Ethernet jacks/transformers.
There should be an arrow on the other side of the header marking.
The connections should go like this:
(from the arrow to the 9X text): NC - TXD - GND - RXD - NC
1. Prepare for installation
While the AP is powering up, interrupt the startup process.
MAKE SURE TO CHECK YOUR CURRENT PARTITION!
If you see: "Current Partition is : partB" or
"Need to switch partition from partA to partB",
you have to force the device into partA mode, before continuing.
This can be done by changing the PKRstCnt to 5 and resetting the device.
setenv PKRstCnt 5
saveenv
reset
After you interrupt the startup process again,
you should see: Need to switch partition from partB to partA
You can now continue to the next step.
If you see: "Current Partition is : partA",
you can continue to the next step.
2. Prevent partition switching.
To prevent the device from switching partitions,
we are going to modify the startup command.
set bootcmd "setenv PKRstCnt 0; saveenv; bootipq"
setenv
3. First boot
Now, we have to boot the OpenWrt intifs.
The easiest way to do this is by using Tiny PXE.
You can also use the normal U-Boot tftp method.
Run "bootp" this will get an IP from the DHCP server
and possibly the firmware image.
If it doesn't download the firmware image, run "tftpboot".
Now run "bootm" to run the image.
You might see:
"ERROR: new format image overwritten - must RESET the board to recover"
this means that the image you are trying to load is too big.
Use a smaller image for the initial boot.
4. Install OpenWrt from initfs
Once you are booted into OpenWrt,
transfer the OpenWrt upgrade image and
use sysupgrade to install OpenWrt to the device.
Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
This commit adds the PHY reset gpio for the LAN1 port to the dts.
According to the GPL sources, gpios 34 and 36 are used on the AVM
FritzBox 7320 and 7330. The second port is unsupported.
The gpio assignment has been verified on the FritzBox 7330.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
No patches needed to be rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
Tested-by: Robert Marko <robimarko@gmail.com> #ipq807x/Dynalink WRX36
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #ipq807x/ax3600, x86_64/FW-7543B, ath79/tl-wdr3600, ipq806x/g10, ipq806x/nbg6817
No patches rebased as a function of this bump.
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
This splits the code in 4 files:
- uencrypt.h
- uencrypt.c - main program
- uencrypt-openssl.c - OpenSSL/wolfSSL implementation
- uencrypt-mbedtls - mbedTLS implementation
Other changes, accounting for ~400 bytes increase in ipk size:
- more error condition checking and reporting,
- hide key and iv command line arguments
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This commit includes some additional changes:
- better handling of iv and keys in openssl/wolfssl variants
- fix compiler warnings and whitespace
- build all 3 variants as separate packages
- adjust the new package name in targets' DEVICE_PACKAGES
- remove PKG_FLAGS:=nonshared
[Beeline SmartBox Flash - OK]
Tested-by: Mikhail Zhilkin <csharper2005@gmail.com>
[after test: replaced a hardcoded IV size of 16 by cipher_info->iv_size]
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Make sure it uses updated Jalapeno BDF inherited from
Device/8dev_jalapeno-common
Fixes: 146eb4925c ("ipq40xx: add support for Crisis Innovation Lab MeshPoint.One")
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[ fix Fixes tag to correct format and fix commit title ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Set specific BDF file for 8devices Habanero/Jalapeno in ipq40xx
generic.mk
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[ split ipq40xx changes in separate commit ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
d978830 rc: add option to get info for a single script in list method
632b4fc rc: add option to skip running check for list method
5577db9 rc: add support for scanning USE_PROCD and skip running if not supported
4de3f02 rc: fix and improve script scanning START and STOP
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
LTO object files will now be compressed using zstd.
Compressing debug sections with zstd will have to wait for GCC 13,
which adds support for -gz=zstd.
NOTE: wiping the ccache is strongly recommended, not doing so might
yield build error later on:
"lto1: internal compiler error: original not compressed with zstd"
Signed-off-by: Andre Heider <a.heider@gmail.com>
Add new patch sent upstream for requesting the memory region in the bcm6345-l1
interrupt controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
autoreconf wants to use the gtkdocize tool now if a configure.ac file
defines GTK_DOC_CHECk(). OpenWrt does not ship the gtkdocize tool, just
use true instead. This fixes the build of some applications like guntls.
Fixes: 030447b8f4 ("tools/autoconf: bump to 2.71")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Upstream introduced a new `trailer.m4` macro file referenced by the
absolute build path of autoconf. Make sure that this is covered by
the `000-relocatable.patch` as well.
This should fix various SDK build failures related to autoconf.
Fixes: 030447b8f4 ("tools/autoconf: bump to 2.71")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Source BDF files out of project dedicated repository and drop local file
from openwrt main repository.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Hardware
--------
CPU: MediaTek MT7621 DAT
RAM: 128MB DDR3 (integrated)
FLASH: 16MB SPI-NOR ()
WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax
SERIAL: 115200 8N1
LEDs - (3V3 - GND - RX - TX) - ETH ports
Installation
------------
Upload the factory image using the Web-UI.
Web-Recovery
------------
The router supports a HTTP recovery mode by holding the reset-button
when powering on. The interface is reachable at 192.168.0.1 and supports
installation using the factory image.
Signed-off-by: David Bauer <mail@david-bauer.net>
odhcp6c logs messages related to its activity when invoked with -v, but
there is no way to configure this from within OpenWrt. This adds a UCI
option to turn on odhcp6c logging, disabled by default. To enable, set,
for example, network.wan6.verbose = 1.
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Setting this options modifies the rootfs size of created images. When
installing a large number of packages it may become necessary to
increase the size to have enough storage.
This option is only useful for supported devices, i.e. with an attached
SD Card or installed on a hard drive.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This updates libtool to its current release, from 2015. Current patches
were renumbered and given a description text. The fix in
160-passthrough-ssp.patch is no longer needed.
A patch to speed up build was cherry-picked, and another openwrt
specific patch was needed to not use quotes in $(SHELL), to acommodate
our "SHELL=/usr/bin/env bash" usage.
The already present call to ./bootstrap ensures that generated files are
refreshed, so the patches are applied only to their sources. Also, that
bootstrap call was adjusted to run at the appropriate time when QUILT=1.
References below are relevant commits to upstream libtool
regarding some of the changes to patches.
This commit is being reapplied after previous revertion, and after some editing.
The fix for the issue that prompted reverting is the parent of this commit.
Ref: 435cb8d71 ("libtoolize: simplify runtime by substituting pkgauxdir")
Ref: 3cf11cfe2 ("libtoolize: rewritten over funclib.sh instead of general.m4sh")
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
[refactored to simplify patch changes, expanded patches, added upstream references]
Signed-off-by: Michael Pratt <mcpratt@pm.me>
libtoolize hardcodes some paths. This is fine when building libtool and
then using it (for example in OpenWrt's buildroot). But when using an
SDK the paths are most likely different.
For example, when building util-linux within an SDK we're greeted with
the following message:
libtoolize: error: $pkgauxdir is not a directory: '/path/to/openwrt/staging_dir/host/share/libtool/build-aux'
This is because staging_dir/host/bin/libtoolize contains the following
hard-coded paths from when the SDK was built in the first place:
prefix="/path/to/openwrt/staging_dir/host"
datadir="/path/to/openwrt/staging_dir/host/share"
pkgauxdir="/path/to/openwrt/staging_dir/host/share/libtool/build-aux"
pkgltdldir="/path/to/openwrt/staging_dir/host/share/libtool"
aclocaldir="/path/to/openwrt/staging_dir/host/share/aclocal"
This commits updates 000-relocatable.patch to correct the paths,
relative to "$STAGING_DIR_HOST".
Ref: 96e05e2e3 ("libtool: Revert "libtool: bump to 2.4.6"")
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
[adapted to older libtool version before bumping, use STAGING_DIR_HOST]
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Add commit messages to patches as intended
by the last bump to libtool which had to be reverted.
This allows for a cleaner diff later,
removing this clutter from the complex changes to patches
that are required to bump to the latest libtool version.
Ref: c377d874b ("libtool: bump to 2.4.6")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Preparation for bumping libtool several versions at once,
which includes some complex changes to patches.
Remove an empty line change from a patch.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Autoconf release 2.71 is a bugfix release of 2.70
Links provided are the changelog of 2.70 [1] [2]
and the announcement of 2.71 [3]
The first patch needed to be rewritten.
Some of the lines in the patch were moved
to be consistent with the same change added upstream
in other similar files.
Second and third patches are no longer needed,
Emacs can now be disabled at the configure stage,
and support for musl was added upstream.
The patch now causes help2man to be required
for installing man pages, but we don't need them.
There is no way to disable man pages build
with the configure script,
so use make to touch the files with the build target install-man1.
Link: https://lists.gnu.org/archive/html/autotools-announce/2020-12/msg00001.html
Link: https://lwn.net/Articles/839395
Link: https://lists.gnu.org/archive/html/info-gnu/2021-01/msg00017.html
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Instead of having a somewhat random list of aclocal symlinks
which are named with the API versioning scheme,
install a symlink for every API version since 1.11
(the first release after Automake was moved to git)
using the API version number from the version of automake
that is currently in openwrt.
Automake API versioning does not include the patch level number.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
The configure option datarootdir
defaults to PREFIX/share.
The Host/Clean define should be Host/Uninstall
otherwise it is removing the build directory
before there is a chance to try "make uninstall"
in that directory.
Host/Clean/Default is no longer defined.
Consolidate the install stage with Host/Uninstall,
since it is essentially uninstalling before installing.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
The configure option datarootdir
defaults to PREFIX/share.
The Host/Clean define should be Host/Uninstall
otherwise it is removing the build directory
before there is a chance to try "make uninstall"
in that directory.
Host/Clean/Default is no longer defined.
Use default build recipes defined in host-build.mk
instead of custom ones that are equivalent.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
The configure option datarootdir
defaults to PREFIX/share.
The Host/Clean define should be Host/Uninstall
otherwise it is removing the build directory
before there is a chance to try "make uninstall"
in that directory.
Host/Clean/Default is no longer defined.
Use default build recipes defined in host-build.mk
instead of custom ones that are equivalent.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
