the following changes are included in this patch:
- node is enabled by default, drop 'status = "okay"'
- adjust order of "compatible" lines and "reg" lines
- add a new blank line before fixed-link node in rtl830x.dtsi
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This patch adds "dts-5.10" directory to use backported drivers.
There are several specification changes in the new drivers, so there
are some compatibility issues in using dts/dtsi files for 5.4.
The old DTS files are moved to "dts-5.4", so their corresponding
kernel version is obvious as well.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[change "dts" to "dts-5.4", adjust Makefile]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The following line is already defined in arch/mips/Kbuild.platforms by
300-mips-add-rtl838x-platform.patch.
platform-$(CONFIG_RTL838X) += rtl838x/
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
A macro with the same name is provided in asm/pgtable.h in Kernel 5.10,
use it and drop from ioremap.h.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This patch backports "irq-realtek-rtl" driver to Kernel 5.10 from 5.12.
"MACH_REALTEK_RTL" is used as a platform name in upstream, but "RTL838X"
is used in OpenWrt, so update the dependency by the additional patch.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
To use backported irq driver, drop old irq driver from realtek target
and call irqchip_init() in setup.c.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
To backport the upstreamed driver (gpio-realtek-otto) from 5.13, drop the
old driver from realtek target.
And, modify 301-gpio-add-rtl838x-driver.patch to remove rtl838x GPIO
support and rename it only for rtl8231 GPIO support.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This patch backports "spi-realtek-rtl" driver to Kernel 5.10 from 5.12.
"MACH_REALTEK_RTL" is used as a platform name in upstream, but "RTL838X"
is used in OpenWrt, so update the dependency by the additional patch.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
To backport the upstreamed driver (spi-realtek-rtl) from 5.12, drop the
old driver from realtek target.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
this patch copies the following files from 5.4 to 5.10:
- config-5.4 -> config-5.10
- files-5.4/ -> files-5.10/
- patches-5.4/ -> patches-5.10/
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[rebase on change in files-5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Expose I2C busses with a chardev device. This is required to control the
PSE controller on the Ubiquiti UniFi Flex Switch.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
MediaTek MT7621AT
16M SPI-NOR Macronix MX25L12835FMI
Microchip PD69104B1 4-Channel PoE-PSE controller
TI TPS2373 PoE-PD controller
PoE-Controller
--------------
By default, the PoE outputs do not work with OpenWrt. To make them output
power, install the "poemgr" package from the packages feed.
This package can control the PD69104B1 PSE controller.
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt" via SSH.
2. Add the uboot-envtools configuration file /etc/fw_env.config with the
following content
$ echo "/dev/mtd1 0x0 0x1000 0x10000 1" > /etc/fw_env.config
3. Update the bootloader environment.
$ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr);
fdt rm /signature; bootubnt"
$ fw_setenv bootcmd "run boot_openwrt"
4. Transfer the OpenWrt sysupgrade image to the device using SCP.
5. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
6. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4
7. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock6
$ dd if=openwrt.bin of=/dev/mtdblock7
8. Reboot the device. It should boot into OpenWrt.
Restore to UniFi
----------------
To restore the vendor firmware, follow the Ubiquiti UniFi TFTP
recovery guide for access points. The process is the same for
the Flex switch.
Signed-off-by: David Bauer <mail@david-bauer.net>
TP-Link CPE710-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on the AP152 reference board
Specifications:
- SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz
- RAM: 128MiB DDR2 @ 650MHz
- Flash: 16MiB SPI NOR Based on the GD25Q128
- Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless
data rate) Based on the QCA9896
- Ethernet: one 1GbE port
- 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal
reflector
- Power, LAN, WLAN5G Blue LEDs
- 3x Blue LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 30-40 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[convert to nvmem, fix MAC assignment in 11-ath10k-caldata]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This backports the upstream commit:
leds: lp55xx: Initialize enable GPIO direction to output
Without it under kernel 5.10 on Asus MAP-AC2200
the LED driver will fail probing:
[ 1.947521] lp5523x: probe of 0-0032 failed with error -22
After the backported fix:
[ 1.873236] lp5523x 0-0032: lp5523 Programmable led chip found
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ipq4029/gl-b1300]
Tested-by: Nick Hainke <vincent@systemli.org> [ipq4019/fritzbox-7530
ipq4019/fritzbox-4040
ipq4019/sxtsq-5ac]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq4019/map-ac2200]
Add kernel 5.10 as the testing kernel to ipq40xx to
get wider testing.
The following devices failed to build with buildbot settings and all
feeds installed (apparently due to kernel size):
* cell-c rtl30vw
* compex wpj428
* devolo magic 2 next
* engenius emr3500
* glinet gl-b1300
* glinet gl-s1300
* qcom ap-dk01.1-c1
* qcom ap-dk04.1-c1
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Nick Hainke <vincent@systemli.org> [ipq4019/fritzbox-7530
ipq4019/fritzbox-4040
ipq4019/sxtsq-5ac]
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ipq4029/gl-b1300]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq4019/map-ac2200]
[add tested-by and note about failed devices]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
MDIO drivers were moved into their own sub directory of networking drivers.
This has caused the AR40xx driver to probe before MDIO drivers and that wont
work as it depends on the MDIO bus to be up so it can be fetched.
Lets solve it by moving the AR40xx into MDIO folder so they get probed like
before.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
This is a required ethtool op since kernel 5.7.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
In kernel v5.5 of_get_phy_mode had its API changed, so its now returning 0
or errors instead of phymode.
Phymode is now returning by passing a pointer to phy_interface_t where it
will be stored.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Copy config from 5.4 and run "make kernel_oldconfig".
Select default ("N") for all new symbols.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[make commit message more explicit]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Refresh the kernel patches on top of 5.10 so they apply.
Manually fixup the 705-net-add-qualcomm-ar40xx-phy.patch
to apply.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
USB and SDHCI LDO DTS patches have been upstreamed into 5.12, so
replace the local versions with upstreamed ones.
Reorder, and clearly mark the kernel version.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
I-O DATA WN-DX2033GR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : Raw NAND 128 MiB (Macronix MX30LF1G18AC-TI)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 2T2R, MediaTek MT7603E
- 5 GHz : 4T4R, MediaTek MT7615
- Ethernet : 5x 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC)
- LEDs/Keys : 2x/3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J5: 3.3V, TX, RX, NC, GND from triangle mark
- 57600n8
- Power : 12 VDC, 1 A
Flash instruction using initramfs image:
1. Boot WN-DX2033GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新") button
to perform firmware update
4. On the initramfs image, download the sysupgrade.bin image to the
device and perform sysupgrade with it
5. Wait ~120 seconds to complete flashing
Notes:
- The hardware of WN-DX2033GR and WN-AX2033GR are almost the same, and
it is certified under the same radio-wave related regulations in Japan
- The last 0x80000 (512 KiB) in NAND flash is not used on stock firmware
- stock firmware requires "customized uImage header" (called as "combo
image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't
- uImage magic ( 0x0 - 0x3 ) : 0x434F4D42 ("COMB")
- header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32"
- image name (0x20 - 0x37) : model ID and firmware versions
- data length (0x38 - 0x3b) : kernel + rootfs
- data crc32 (0x3c - 0x3f) : kernel + rootfs
- There are 2x important flags in the flash:
- bootnum : select os partition for booting (persist, 0x4)
- 0x01: firmware
- 0x02: firmware_2
- debugflag : allow interrupt kernel loader, it's named as "Z-LOADER"
(Factory, 0xFE75)
- 0x00: disable debug
- 0x01: enable debug
MAC addresses:
LAN : 50:41:B9:xx:xx:90 (Factory, 0xE000 (hex) / Ubootenv, ethaddr (text))
WAN : 50:41:B9:xx:xx:92 (Factory, 0xE006 (hex))
2.4 GHz : 50:41:B9:xx:xx:90 (Factory, 0x4 (hex))
5 GHz : 50:41:B9:xx:xx:91 (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
GPIOs > 31 require special handling. This patch fixes both the
initialisation and direction get/set operations.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
Add additional header information required for newer
bootloaders found on DIR-2660-A1 & A2.
Also remove the MTD splitter compatible from the second firmware
partition, as OpenWrt only supports handling of the first one.
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
[rephrase commit message, remove removal of read-only flags]
Signed-off-by: David Bauer <mail@david-bauer.net>
The rockchip platform supports squashfs SD card images. However, the
resulting image is not padded to completely fill the rootfs partition.
Because of that, the f2fs overlay might not be erased, resulting in
uci-defaults not bing executed or the configuration not being erased,
even though drop config was selected.
Modify the image generation process so the image is padded to cover the
entire root filesystem partition.
Signed-off-by: David Bauer <mail@david-bauer.net>
Remove use of DEVICE_TITLE in favor of the
DEVICE_VENDOR and DEVICE_MODEL as used by
all other targets.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Remove use of DEVICE_TITLE in favor of the
DEVICE_VENDOR and DEVICE_MODEL as used by
all other targets.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Using `make info` show the current target, revision, default packages
and available profiles. This commits adds the used architecture.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Meraki wrote the ethernet MAC-address of the device
onto the eeprom (AT24C64) at the fixed location 0x66
to 0x6C. Let's fetch it from there.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
broke support for Meraki MR32 and this patch makes the replacement
configurable allowing for specifying the @ or - or whatever character
that is desired to retain backwards compatibility with existing devices.
For example, this patch includes the fix for the Meraki MR32 in
target/linux/bcm53xx/image for meraki_mr32:
DEVICE_DTS_DELIMITER := @
DEVICE_DTS_CONFIG := config@1
Fixes: 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Signed-off-by: Damien Mascord <tusker@tusker.org>
[Added tags, checkpatch.pl fixes, noted that this is for old stuff]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
With GCC11, memcpy doesn't work here as it assumes a size of 0. Use
ioremap to avoid it.
Fixed parameter type to match board_get_mac_address.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This fixes:
Distributed Switch Architecture (NET_DSA) [Y/n/m/?] y
Tag driver for Atheros AR9331 SoC with built-in switch (NET_DSA_TAG_AR9331) [N/m/y/?] n
Tag driver for Broadcom switches using in-frame headers (NET_DSA_TAG_BRCM) [N/m/y/?] n
Tag driver for Broadcom legacy switches using in-frame headers (NET_DSA_TAG_BRCM_LEGACY) [N/m/y/?] (NEW)
Error in reading or end of file.
Fixes: 8fa1b576bb ("linux: update b53 upstream driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Specifying serial in bootargs is not needed since the commit
ffeb37047e ("procd: update to git HEAD"). It's thanks to the procd
commit 2cfc26f8456a ("inittab: detect active console from kernel if no
console= specified").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Build cortexa7 subtarget with DSA driver for MDIO-connected Broadcom
BCM53xxx switches. This is needed for the Lamobo R1 aka. BananaPi
BPi-R1 board which comes with such a switch IC.
Remove old swconfig driver from target kernel config as the only board
using it is now supported by the DSA driver.
No changes to device tree are needed as upstream DTS already got a
DSA switch definition and we are just using that upstream source.
Update default network config of the Lamobo R1 to create lan bridge
with all 4 lan ports.
Introduce DEVICE_COMPAT_VERSION for the board to inform users about
having the re-create their network configuration and add device alias
as Bananapi BPi-R1 while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Changes from 5.4 to 5.10:
-------------------------
- patches from 5.4 are all upstream for 5.10 execpt for
0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch
- disable block device data integrity (DIF/DIX/T10) in default config
(CONFIG_BLK_DEV_INTEGRITY)
This feature is only supported by:
- Enterprise SAS/SCSI HBAs and Disks
- Software raid
- NVMEs with metadata capabilities (most don't have this)
None of which are part of any octeontx boards.
- arm64 TEXT_OFFSET (0x80000) has been removed after 5.4
This will break Uimages with kernel load addresses that aren't 2MiB
aligned any longer. Resulting in the kernel silently fail to boot.
For Gatworks newport boards for example, the uimage kernel load
and execute address is 0x20080000. These need to be changed to
0x20000000 when running kernels beyond 5.4.
Tested-on: Gateworks Newport GW64xx
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Linksyses Audi EA3500 and Viper E4200/E4500 have too small kernel
partition size when kernel 5.10 is used. This patch change kernel
partition to maximum size allowed by u-boot.
Kernel size is overlapping rootfs now, like mvebu Linksyses and stock
partition table. It fix back to stock via sysupgrade, which was broken
since 18.06.
Fixes: 9808b9ae02 ("kirkwood: switch to kernel 4.9")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The ZyXEL GS1900-24HPv2 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HPv2
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: W631GG8MB-12 128 MiB DDR3 SDRAM
(stock firmware is configured to use only 64 MiB)
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
24 ethernet port PoE status LEDs
2 SFP status/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESTORE" button on front panel
1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J41) with populated standard pin connector on
the left edge of the PCB, angled towards the side.
The casing has a rectangular cutout on the side that provides
external access to these pins.
Pinout (front to back):
+ GND
+ TX
+ RX
+ VCC
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
OEM upgrade method:
(Possible on master once https://patchwork.ozlabs.org/project/openwrt/patch/20210624210408.19248-1-bjorn@mork.no/ is merged)
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HPv2 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Soma Zambelly <zambelly.soma@gmail.com>
like commit 78c1ed6. Without this,Some USB port on H3 baseboard
can' work. So, need enable MUSB support on this target.
Signed-off-by: Zhao Yu <574249312@qq.com>
