Do not parse /tmp/sysinfo/board_name, /proc/cpuinfo or the device tree
compatible string directly. Always use the board_name function to get
the board name.
The admswconfig package still reads /proc/cpuinfo directly. The code
looks somehow broken and the whole adm5120 which uses this package
looks unmaintained. Leave it as it is for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
For targets using the generic board detection and board specific
settings in diag.sh, the board name is still unset at the time the
set_state() provided by diag.sh is called by 10_indicate_preinit.
Change the execution order to ensure the boardname is populated before
required the first time. Do the target specific board detection as
early as possible, directly followed by the generic one to allow a
seamless switch to the generic function for populating /tmp/sysinfo/.
Signed-off-by: Mathias Kresin <dev@kresin.me>
- Refreshed all patches
- Removed upstreamed
- Adapted 4 patches:
473-fix-marvell-phy-initialization-issues.patch
-----------------------------------------------
Removed hunk 5 which got upstreamed
403-net-phy-avoid-setting-unsupported-EEE-advertisments.patch
404-net-phy-restart-phy-autonegotiation-after-EEE-advert.patch
--------------------------------------------------------------
Adapted these 2 RFC patches, merging the delta's from an upstream commit
(see below) which made it before these 2.
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-
stable.git/commit/?h=v4.9.36&id=97ace183074d306942b903a148aebd5d061758f0
180-usb-xhci-add-support-for-performing-fake-doorbell.patch
-----------------------------------------------------------
- Moved fake_doorbell bitmask due to new item
Compile tested on: cns3xxx, imx6
Run tested on: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
- Refreshed all patches
- Adapted 1 (0031-mtd-add-SMEM-parser-for-QCOM-platforms.patch)
Compile tested on: brcm2708, cns3xxx, imx6
Run tested on: brcm2708, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[Compile and run tested on brcm2708]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
This patch fixes a problem where the AR8035 PHY can't be
detected on the Cisco Meraki MR24, when the ethernet cable
is not connected during boot.
Russell Senior reported:
|This appears to be a problem during probing of the AR8035
|phy chip. When ethernet has no link, the phy detection fails,
|and eth0 is not created. Plugging ethernet later has no effect,
|because there is no interface as far as the kernel is
|concerned. The relevant part of the boot log looks like this:
|
|[ 0.876611] /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode
|[ 0.882532] /plb/opb/ethernet@ef600c00: reset timeout
|[ 0.888546] /plb/opb/ethernet@ef600c00: can't find PHY!
(<https://bugs.lede-project.org/index.php?do=details&task_id=687>)
Fixes FS#687
Cc: Chris Blake <chrisrblake93@gmail.com>
Reported-by: Russell Senior <russell@personaltelco.net>
Fixes: 23fbb5a87c56e98 ("emac: Fix EMAC soft reset on 460EX/GT")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
CONFIG_SG_POOL symbol is selected only by CONFIG_SCSI, since the last
one is disabled by default then disable CONFIG_SG_POOL by default too.
And explicitly enable it only for platforms that use CONFIG_SCSI.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Both of these boards share the same DTS, and hardware. The only
difference would be the PCI-E slot, and ath9k card found on the MX60W.
Due to the similarities, it would be more efficient to merge these
profiles.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This moves core router packages to the NAND target, to ensure they are
applied to all images. This change is being done due to an issue found
when flashing the MX60W image, which came without these when built as a
multi image.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This patch moves the fakeroot code required by some devices to
`image-commands.mk`.
Create the fakeroot on the fly by using the undocumented -s (skip copy)
parameter of mkimage.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
[remove unused NETGEAR_KERNEL_MAGIC, remove workarounds to have a dummy
rootfs for mkimage]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reduces the amount of hacks in the makefile code.
Remove the apm821xx code to do the same - it was broken and left both
compressed and uncompressed images in $(BIN_DIR)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Refresh patches on all 4.4 supported platforms.
077-0005-bgmac-stop-clearing-DMA-receive-control-register-rig.patch
removed as now upstream.
Compile & run tested: ar71xx - Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Currently, the device-tree partition is marked as read-only.
Hence, userspace tools like mtd can't write into the partition.
This however will be necessary in case the DTB needs to be
updated.
This patch also adds the kernel.dtb image, so the compiled
DTB is exported as a file and available in the binary
directory along the firmware images.
Note: the u-boot does expects the dtb to be a uimage.
To update the dtb manually:
1. copy the generated dtb to the router.
2. mtd erase /dev/mtd2
3. mtd write wndr4700.dtb /dev/mtd2
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for the Cisco Meraki MX60/MX60W Security
Appliance. Flashing information can be found at
https://github.com/riptidewave93/LEDE-MX60
Specs are as follows:
AppliedMicro APM82181 SoC at 800MHz
1GiB NAND - Samsung K9K8G08U0D
512MB DDR RAM - 4x Nanya NT5TU128M8GE-AC
Atheros AR8327-BL1A Gigabit Ethernet Switch
1x USB 2.0 Port
More info can be found at https://wiki.openwrt.org/toh/meraki/mx60
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This special dwc2 device definition for the Netgear WNDR4700
has been replaced by amcc,usb-otg-405ex.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch moves the common SoC device tree entries
from the currently four supported platforms into a
common apm82181.dtsi.
Furthermore, this patch also changes the GPIO, IRQ and
input definitions of the supported platforms to use the
defined dt-bindings macros for GPIO_ACTIVE_LOW|HIGH,
KEY_WPS|RESTART|*, IRQ_TYPE_* when it's appropriate.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for the amcc,usb-otg-405ex device
which is found in all APM82181 SoCs.
Note: The system can't use the generic "snps,dwc2" compatible
because of the special ahbcfg configuration. The default
GAHBCFG_HBSTLEN_INCR4 of snps,dwc2 can cause a system hang
when the USB and SATA is used concurrently.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Because the WAN port is handled by the internal AR8327N switch, the
device should use swconfig_leds trigger to handle the link activity
of the WAN LED. This has the added bonus that the WAN LED will now
go dark if there's no ethernet cable connected to the WAN port.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The old usbdev trigger never supported assigning more than 1 USB port.
This code we got was never working as expected and it was missing 2 more
ports. Switch to usbport to have LED working with all ports.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The patch "images: bump default rootfs size to 256 MB"
a1f83bad60 caused a crash
during boot for the recovery images. This is because
both variants of the MyBook Live only have 256MB of RAM
and for the recovery option, the ext4 rootfs was simply
stored in the RAMDISK.
This patch replaces recovery image for the MBL with an
initramfs kernel.
In order to boot the initramfs (for recovery or development):
0. copy the initramfs and device tree into tftp's server directory
# cp *-initramfs-kernel.bin to /tftp-server/mbl.bin
# cp *-ext4-kernel.dtb to /tftp-server/fdt.bin
1. Connect the MyBook Live (Duo) serial port.
(Warning! Use a 3.3v level shifter).
2. Hit Enter during u-boot and insert these three lines:
# setenv serverip 192.168.1.254; setenv ipaddr 192.168.1.1;
# tftp ${kernel_addr_r} mbl.bin; tftp ${fdt_addr_r} fdt.bin
# run addtty addmisc; bootm ${kernel_addr_r} - ${fdt_addr_r}
Where 192.168.1.254 is your TFTP server.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The insertion or removal of the sd-card cannot be detected
by the hardware itself. This is by design. To workaround this,
for the WNDR4700 unload/load the dwc2 module in case the
the special SD CARD GPIO line is low/high.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Russell Senior reported an issue with the MR24 initramfs kernels:
> ## Booting kernel from Legacy Image at 00c10000 ...
> Image Name: POWERPC LEDE Linux-4.4.19
> Created: 2016-08-31 11:57:05 UTC
> Image Type: PowerPC Linux Kernel Image (gzip compressed)
> Data Size: 2155723 Bytes = 2.1 MiB
> Load Address: 00000000
> Entry Point: 00000000
> Verifying Checksum ... OK
>Wrong Ramdisk Image Format
>Ramdisk image is corrupt or invalid
For the MR24, the kernel is uploaded to 0x10000. The ramdisk starts
at 0x200000. This leaves the kernel with just 0x1f0000 bytes = 1984kb.
This patch adds a size check so the image creation script will abort
instead of producing a unbootable initramfs image. A separate patch
"apm821xx: Fix initramfs image for the Meraki MR24" which fixed the
reported issue was submitted earlier.
Cc: Russell Senior <russell@personaltelco.net>
Cc: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
When gzip is used, our kernel is too large and this causes the ramdisk
to be at the wrong offset. Fix by moving to lzma.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Change the image build code to generate the DTB files as part of the kernel
build phase in order to fix the image build in the ImageBuilder environment.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The consolidation of the MR24 and WNDR4700 subtargets
into the nand subtarget broke MR24's atheros wlan.
This was because the wndr4700's board code used a
pci_fixup routines to supply the ath9k module with
the calibration data.
This is not necessary on the MR24 as it has standard
mini-pcie ports. Hence the two AR9380 mini-pcie cards
do not need any calibration data overrides.
Cc: chrisrblake93@gmail.com
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
