Serge Vasilugin reports:
To improve mt7620 built-in wifi performance some changes:
1. Correct BW20/BW40 switching (see comments with mark (1))
2. Correct TX_SW_CFG1 MAC reg from v3 of vendor driver see
https://gitlab.com/dm38/padavan-ng/-/blob/master/trunk/proprietary/rt_wifi/rtpci/3.0.X.X/mt76x2/chips/rt6352.c#L531
3. Set bbp66 for all chains.
4. US_CYC_CNT init based on Programming guide, default value was 33 (pci),
set chipset bus clock with fallback to cpu clock/3.
5. Don't overwrite default values for mt7620.
6. Correct some typos.
7. Add support for external LNA:
a) RF and BBP regs never be corrected for this mode
b) eLNA is driven the same way as ePA with mt7620's pin PA
but vendor driver explicitly pin PA to gpio mode (for forrect calibration?)
so I'm not sure that request for pa_pin in dts-file will be enough
First 5 changes (really 2) improve performance for boards w/o eLNA/ePA.
Changes 7 add support for eLNA
Configuration w/o eLAN/ePA and with eLNA show results
tx/rx (from router point of view) for each stream:
35-40/30-35 Mbps for HT20
65-70/60-65 Mbps for HT40
Yes. Max results for 2T2R client is 140-145/135-140
with peaks 160/150, It correspond to mediatek driver results.
Boards with ePA untested.
Reported-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Prepare patches for sending upstream by adding patch descriptions
generated from the original OpenWrt commits adding each patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It is common for 802.11ax NICs to support more than just AP mode, which
results in there being a distinct set of HE capabilities for each mode. As
(bad) luck would have it, iw prints out info for each HE mode in sequential
order according to `enum nl80211_iftype`, and AP mode isn't always first.
As a result, the wrong set of HE capabilities can be parsed if an AP NIC
supports station (managed) mode or any other mode preceding AP mode, since
only the first set of HE capabilities printed by iw is parsed from awk's
output.
This has a noticeable impact on beamforming for example, since managed mode
usually doesn't have beamformer capabilities enabled, while AP mode does.
Hostapd won't be set up with the configs to enable beamformer capabilities
in this scenario, causing hostapd to disable beamforming to HE stations
even when it's supported by the AP.
Always parse the correct set of HE capabilities for AP mode to fix this.
This is achieved by trimming all of iw's output prior to the AP mode
capabilities, which ensures that the first set of HE capabilities are
always for AP mode.
Signed-off-by: Sultan Alsawaf <sultan@kerneltoast.com>
Add support for randomly generating a MAC address for a wifi-iface
instance by setting `macaddr` to `random`
When set to `random`, a new locally administered unicast MAC address
is generated and assigned to the iface everytime it is (re-)configured
Signed-off-by: Manas Sambhus <manas.sambhus+github@gmail.com>
Backports upstream fix from 5.19
lockdep complains use of uninitialized spinlock at ieee80211_do_stop() [1],
for commit f856373e2f31ffd3 ("wifi: mac80211: do not wake queues on a vif
that is being stopped") guards clear_bit() using fq.lock even before
fq_init() from ieee80211_txq_setup_flows() initializes this spinlock.
According to discussion [2], Toke was not happy with expanding usage of
fq.lock. Since __ieee80211_wake_txqs() is called under RCU read lock, we
can instead use synchronize_rcu() for flushing ieee80211_wake_txqs().
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This updates mac80211 to version 5.15.58-1 which is based on kernel
5.15.58.
The removed patches were applied upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
TechNexion PICO-PI-IMX7D uses BCM4339 Wi-Fi interface in SDIO mode.
Enable SDIO support for imx/cortexa7 to fully support it in images.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
The mac80211-hwsim and the Intel iwlwifi driver support ieee80211ax, add
the missing DRIVER_11AX_SUPPORT dependency too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In Turris MOX SDIO card [1], which uses Marvell 88W997 and its driver
mwifiex, you might get cryptic messages, which are not helpful to use.
@pali created patch, which improves messages by the driver and he will
send this to Linux kernel soon.
Before:
[ 81.026156] mwifiex_sdio mmc1:0001:1: CMD_RESP: cmd 0x20 error, result=0x1
After:
[ 15.784018] mwifiex_sdio mmc1:0001:1: CMD_RESP: cmd RF_ANTENNA (0x20) error, result=0x1
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
SDIO chip 88W9997 from NXP [1] is quite limited by its firmware and
driver. Add hacky patch to allow up to 4 SSID instead of 3 SSID.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Introduce a new option background_radar to toggle hostapd's background
radar feature. Enabling this allows DFS CAC to run on dedicated radio RF
chains while the radio(s) are otherwise running normal AP activities on
other channels.
As OpenWrt configures hostapd to use a channel list even when a single
channel is configured, using this feature requires a list of channels in
/etc/config/wireless. Alternatively, channel can be set to auto.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Enable ath10k offload by default. This improves wireless performance
without requiring user configuration.
This adds ath10k_core to the AUTOLOAD section so that the frame_mode
paramter can be added to /etc/modules.d and passed to the driver.
The frame_mode 2 enables ethernet mode on the firmware/driver.
This parameter is set by passing a different value to the frame_mode
value on kmod insmod.
Link to the original patchset:
https://patchwork.kernel.org/project/linux-wireless/cover/20220516032519.29831-1-ryazanov.s.a@gmail.com/
Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com>
This reverts the airtime scheduler back from the virtual-time based scheduler
to the deficit round robin scheduler implementation.
This reduces burstiness and improves fairness by improving interaction with AQL.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The MAC can be stored in OTP memory or in flash memory, currently the
driver could read it only from OTP. Backport the patch allowing setting
the MAC address from flash. Some modules have the OTP programmed but
the ODM/OEM decided to overwrite it with value stored in flash.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
This backports encap offload support from upstream.
On some ath10k devices there can be about 10% improvement on tx throughput.
Users can turn it on by setting frame_mode=2.
Signed-off-by: Zhijun You <hujy652@gmail.com>
Sync nl80211.h with upstream in order to maintain parity with
nl80211_copy.h shipped with hostapd.
This is necessary, as currently the enum value for
NL80211_EXT_FEATURE_RADAR_BACKGROUND mismatches between hostapd and
mac80211. This breaks background radar capability detection in hostapd.
Reported-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David Bauer <mail@david-bauer.net>
In case no specific BSS color is configured, set it to a random value.
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
latency and short-term fairness is improved by fixing the tx queue sorting
so that it considers the pending AQL budget
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add ieee80211_rx_check_bss_color_collision routine in order to introduce
BSS color collision detection in mac80211 if it is not supported in HW/FW
(e.g. for mt7915 chipset).
Add IEEE80211_HW_DETECTS_COLOR_COLLISION flag to let the driver notify
BSS color collision detection is supported in HW/FW. Set this for ath11k
which apparently didn't need this code.
Tested-by: Peter Chiu <Chui-Hao.Chiu@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/a05eeeb1841a84560dc5aaec77894fcb69a54f27.1648204871.git.lorenzo@kernel.org
[clarify commit message a bit, move flag to mac80211]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Some ath10k IPQ40xx devices like the MikroTik hAP ac2 and ac3 require the
BDF-s to be extracted from the device storage instead of shipping packaged
API 2 BDF-s.
This is required as MikroTik has started shipping boards that require BDF-s
to be updated, as otherwise their WLAN performance really suffers.
This is however impossible as the devices that require this are release under
the same revision and its not possible to differentiate them from devices
using the older BDF-s.
In OpenWrt we are extracting the calibration data during runtime and we are
able to extract the BDF-s in the same manner, however we cannot package the
BDF-s to API 2 format on the fly and can only use API 1 to provide BDF-s on
the fly.
This is an issue as the ath10k driver explicitly looks only for the board.bin
file and not for something like board-bus-device.bin like it does for pre-cal
data.
Due to this we have no way of providing correct BDF-s on the fly, so lets
extend the ath10k driver to first look for BDF-s in the board-bus-device.bin
format, for example: board-ahb-a800000.wifi.bin
If that fails, look for the default board file name as defined previously.
So, backport the upstream ath10k patch.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit f9ff282d17 as during
upstream patch review process nbd pointed out, that this patch needs
more work:
"The patch looks wrong to me. I'm pretty sure that AR_CH0_TOP2 is the
correct register, the definition has an explicit check for 9561 as well.
I believe this patch works by accident because it avoids writing a wrong
value to that register."
1. https://lore.kernel.org/all/91c58969-c60e-2f41-00ac-737786d435ae@nbd.name
Signed-off-by: Petr Štetiar <ynezz@true.cz>
ath9k is setting the TX PA DC bias level different on QCA9561 and QCA9565
although they have the same radio IP-core, which results in a very low
output power and very low throughput as devices are further away from
the AP (compared to other 2.4GHz APs.)
In real life testing, without this patch the 2.4GHz throughput on Yuncore
XD3200 is around 10Mbps sitting close to the AP, and close to theoretical
maximum with the patch applied.
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
[edit commit message]
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This updates mac80211 to version 5.15.33-1 which is based on kernel
5.15.33.
The removed patches were applied upstream.
This new release contains many fixes which were merged into the upstream
Linux kernel.
This also contains the following new drivers which are needed for ath11k:
* net/qrtr/
* drivers/bus/mhi/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
LOCK_STATE_HELD define was omitted during backport of
lockdep_assert_not_held() which leads to build failures of kernels with
CONFIG_LOCKDEP=y:
backports-5.15.8-1/backport-include/linux/lockdep.h:16:47: error: 'LOCK_STATE_HELD' undeclared (first use in this function)
Fix it by adding missing LOCK_STATE_HELD define.
References: PR#9373
Reported-by: Oskari Rauta <oskari.rauta@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Both struct net_device_path_ctx and struct net_device_path
are not available in 5.4. This causes an build error on the
bcm63xx target.
|mac80211/driver-ops.h: In function 'drv_net_fill_forward_path':
|driver-ops.h:1502:57: error: passing argument 4 of
|'local->ops->net_fill_forward_path' from incompatible pointer type
| [-Werror=incompatible-pointer-types]
| 1502 | ctx, path);
| | ^~~
| | |
| | struct net_device_path_ctx *
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit adds the following package compile options.
CONFIG_PACKAGE_RTW88_DEBGUG:
Compile the driver with additional debug logging output
CONFIG_PACKAGE_RTW88_DEBGUGFS:
Add the possibility to map information about the driver rtw88 into
debugfs.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
